Peerless Industries TV Mount 201 9421 10 User Manual

Installation and Assembly:  
SmartMount™ Universal Tilt Wall Mount  
for 10" - 24" LCD Flat Panel Screens  
Models: ST 630P, ST 630P-S, ST 630, ST 630-S  
This product is intended for use with UL  
Listed products and must be installed by a  
qualified professional installer.  
Features:  
R
• Fits 10" to 24" LCD flat panel screens  
• One-touch tilt for effortless positioning and adjustment of the screen  
Max UL Load Capacity: 80 lb (36.3 kg)  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 04-27-05 SHEET #: 201-9421-10 10-27-09  
 
Parts List  
ST 630P  
Qty Part #  
ST 630P-S ST 630  
ST 630-S  
Part #  
Description  
Part #  
Part #  
adapter plate  
tilt assembly  
Alligator® anchor  
M4 x 10 mm phillips screw  
M4 x 20 mm phillips screw  
retaining spacer  
#14 x 2-1/2" hex head wood screw  
M5 x 6 mm screw  
1
1
2
4
4
4
2
1
1
095-1346  
095-0359  
590-0097  
504-9012  
504-9020  
590-5005  
095-4346  
095-0360  
590-0097  
504-9012  
504-9020  
590-5005  
095-1346  
095-0359  
590-0097  
504-9012  
504-9020  
590-5005  
095-4346  
095-0360  
590-0097  
504-9012  
504-9020  
590-5005  
A
B
C
D
E
F
G
H
I
5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03  
520-1023  
520-1023  
520-1114  
560-1133  
520-1114  
560-1133  
security driver  
A
B
C
D
E
F
G
H
I
ISSUED: 04-27-05 SHEET #: 201-9421-10 10-27-09  
3 of 7  
 
Installation to Single Wood Stud Wall  
WARNING  
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and  
components.  
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based  
on its edges, draw a vertical line down the stud’s center. Place tilt assembly (B) on wall as a template, making sure  
that the two mounting holes are over the stud centerline. Level tilt assembly, and mark the center of the two holes.  
Drill two 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the tilt assembly is level, secure it using two  
#14 x 2-1/2" wood screws (G) as shown.  
1
Skip to step 2 on page 6.  
WARNING  
• Tighten wood screws so that tilt assembly is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is  
highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers  
are responsible to provide hardware for other types of mounting situations.  
B
G
ISSUED: 04-27-05 SHEET #: 201-9421-10 10-27-09  
4 of 7  
 
Installation to Solid Concrete or Cinder Block  
WARNING  
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete  
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid  
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-  
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to  
avoid breaking out the back of the hole when entering a void or cavity.  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and  
components.  
Make sure that tilt assembly (B) is level, use it as a  
concrete  
surface  
1
template to mark two mounting holes. Drill two 1/4"  
(6 mm) dia. holes to a minimum depth of 2-1/2"  
(64 mm). Insert anchors (C) in holes flush with wall  
as shown (right). Place tilt assembly over anchors  
and secure with two #14 x 2-1/2" screws (G). Level,  
then tighten all fasteners.  
1
C
Drill holes and insert anchors (C).  
2
WARNING  
B
• Tighten screws so that wall plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
C
G
• Never tighten in excess of 80 in. • lb (9 N.M.).  
Place assembly (B) over anchors (C) and secure with screws (G).  
3
WARNING  
• Always attach concrete expansion anchors directly to  
load-bearing concrete.  
• Never attach concrete expansion anchors to concrete  
covered with plaster, drywall, or other finishing mate-  
rial. If mounting to concrete surfaces covered with a  
finishing surface is unavoidable, the finishing surface  
must be counterbored as shown below. Be sure  
concrete anchors do not pull away from concrete  
when tightening screws. If plaster/drywall is thicker  
than 5/8", custom fasteners must be supplied by  
installer.  
Tighten all fasteners.  
C
CORRECT  
INCORRECT  
B
wall plate  
concrete  
concrete  
wall  
plate  
plaster/  
drywall  
plaster/  
drywall  
G
ISSUED: 04-27-05 SHEET #: 201-9421-10 10-27-09  
5 of 7  
 
Attaching Adapter Plate to Flat Panel Screen  
WARNING  
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly  
secured, damage may occur to screen or product may fail.  
FORVESA® 75MOUNTINGPATTERN:  
FORVESA100MOUNTINGPATTERN:  
2
Choose hole pattern as shown below. Attach adapter  
plate (A) to back of screen using four M4 x 10 mm  
screws (D) as shown below.  
Choose hole pattern as shown below. Attach adapter  
plate (A) to back of screen using four M4 x 10 mm  
screws (D) as shown below.  
*Note: If hole pattern is in a pocket, attach adapter  
plate (A) to back of screen using four M4 x 20 mm  
screws (E) and four retaining spacers (F) as indicated  
below.  
A
D
A
D
*For screens with a hole  
pattern in a pocket,  
spacers (F) go between  
adapter plate (A) and  
screen.  
F
ISSUED: 04-27-05 SHEET #: 201-9421-10 10-27-09  
6 of 7  
 
Installing and Removing Flat Panel Screen  
Attach screen to tilt assembly (B). Tighten M5 x 6  
mm screw (H) to lock screen to tilt assembly.  
3
SCREEN  
Note: For security models, use security driver (I) to  
tighten M5 x 6 mm screws (H).  
H
To remove screen from mount, loosen screw (H) and  
lift screen off of mount.  
A
WARNING  
• Do not lift more weight than you can handle. Use  
additional man power or mechanical lifting equipment  
to safely handle placement of the screen.  
• Failure to lock adapter plate (A) with screw (H) can  
cause screen to come off mount if hit accidentally.  
B
CAUTION  
• Do not tighten screws with excessive force.  
Overtightening can cause damage to mount. Tighten  
screws to 20 in. • lb (2.26 N.M.) maximum torque.  
fig. 3  
Adjusting the Tilt Angle of the Flat Panel Screen  
Adjust tension knob on right side of mount shown in  
figure 4 to desired tension to balance your screen  
size and weight.  
4
Note: If knob is inaccessible, remove screen from  
mount, adjust tension knob to desired tension to  
balance your screen size and weight, and reattach  
screen to mount as stated in step 3.  
Push or pull from top or bottom of screen to adjust  
tilt as shown in figure 4. The tilt can be adjusted to a  
maximum of 15° forward or 5° backward.  
TENSION KNOB  
CAUTION  
• Do not tighten screws with excessive force.  
Overtightening can cause damage to mount. Tighten  
screws to 40 in. • lb (4.5 N.M.) maximum torque.  
CAUTION  
• Be careful not to pinch fingers when pushing screen  
from the bottom.  
fig. 4  
ISSUED: 04-27-05 SHEET #: 201-9421-10 10-27-09  
7 of 7  
©2007, PeerlessIndustries, Inc. Allrightsreserved.  
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.  
 

Pelco Home Security System C1306M D 7 09 User Manual
Pelco Switch MS504AFL User Manual
Perlick Refrigerator BLM 2000 User Manual
Philips DVD Player MCP9360i User Manual
Philips Stereo System AS140 User Manual
Philips TV VCR Combo CCA193AT User Manual
Pioneer Car Stereo System DEH P3370XM User Manual
Planet Technology Network Card WNL U552 User Manual
Polaris Offroad Vehicle Sportsman 500 EFI User Manual
Praktica Digital Camera D00431 User Manual