®
KBD9000
Transmitter/
Controller
Installation/
Operation Manual
C551M (4/98)
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
1.0 GENERAL
1.1 IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be
observed.
1. Installation and servicing should only be done by Qualified Service Personnel
and conform to all Local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or
6P enclosure, it is designed for indoor use only and it must not be installed
where exposed to rain and moisture.
3. Only use replacement parts recommended by Pelco.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
CAUTION:
RISK OF
ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
Please thoroughly familiarize yourself with the information
in this manual prior to installation and operation.
Pelco Manual C551M (4/98)
3
1.2 REGULATORY NOTICES
NOTE: This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that
the interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try and cor-
rect the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
1.3 UNPACKING INSTRUCTIONS
Unpack and inspect all parts carefully.
The following items are supplied:
1
1
1
KBD9000 Transmitter/Controller
Installation/Operation Manual (C551M)
12 VAC Wall Mount Transformer
Be sure to save the shipping carton, boxes and inserts. They are the safest material
in which to make future shipments.
If an item appears to have been damaged in shipment, replace it properly in its box
and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replacement.
(International customers fax 1-559-348-1120 for authorization and instructions.)
If an item needs to be returned to the factory for repair, consult the WARRANTY
AND RETURN section of this manual for instructions.
4
Pelco Manual C551M (4/98)
2.0 DESCRIPTION
The KBD9000 Transmitter/Controller is a desk top unit that provides up to 16 re-
mote control functions. It operates without the need for control cables other than for
a dedicated video cable for the normal transmission of a remote camera signal to
the local monitoring and control position. Coaxitron® control lends itself to applica-
tions where short-to-medium distances are involved and where equalization of cable
losses is not required.
Check your receiver/driver manual for active functions.
Typically, control functions are:
1. Pan Left
2. Pan Right
3. Tilt Up
4. Tilt Down
5. Zoom In
6. Zoom Out
7. Focus Near
8. Focus Far
9. Iris Open
10. Iris Close
11. Camera Power On/Off
12. Auto/Manual Scan
13. AUX 1
14. AUX 2
15. AUX 3
16. AUX 4
Functions 1 through 10, 15 and 16 are momentary; that is, they are only actuated
while the associated control switch on the KBD9000 is operated. Functions 11, 12,
13 and 14 are latching; that is, camera power, auto scan, and auto/ manual iris are
latching functions and remain on until turned off. The latching iris function is not
dedicated, and with proper interfacing, it can be used for some other latching func-
tion. Alternately, AUX 1, 2, 3 and 4 may be used as momentary functions to control
such things as lights or gates with proper external interfacing. Up to ten functions
can be operated simultaneously. Functions 11 through 16 must be used individu-
ally; although any one of these functions may be used simultaneously with func-
tions 1 through 10.
KBD9000 is an improved version of the original Coaxitron® transmitter/controller.
Improvements include the following features:
1. When used with a Pelco CX900TLC Test Local Control Plug-in Module, pro-
vides troubleshooting capability for both the receiver and the KBD9000.
2. Pan/tilt, zoom, and camera power control are included on the main receiver
board, which eliminates malfunctions due to incorrect wiring or broken wires.
Pelco Manual C551M (4/98)
5
KBD9000 provides the following standard functions:
1. Pan/Tilt
2. Lens Control — Zoom, iris, and focus
3. Camera power (on/off)
The KBD9000 does not have preset capabilities, but it will work with receivers
capable of doing presets.
2.1 MODELS
KBD9000
Desktop Coaxitron® transmitter/controller with pan & tilt and
zoom lens control. 120 VAC input.
KBD9000-X
Same as the KBD9000 except 230 VAC input. (CE)
2.2 CERTIFICATIONS
The products identified below have been tested and certified for agency compli-
ance
as noted.
Agency Compliance Certification
Model
CE
FCC
UL
CSA/cUL
KBD9000
KBD9000-X
X
X
Applicable CE, FCC, UL, and CSA/cUL directives/standards:
•
93/68/EEC–CE Mark Directive
89/336/EEC, 92/31/EEC–Electromagnetic Compatibility (EMC)
Directives
•
•
•
EN 55022: 1984 Class B–Radio-frequency emissions limits
EN 55082-2: 1992–Immunity standard
•
•
•
IEC 801-2: 1984–ESD immunity
IEC 801-3: 1984–Radiated field immunity
IEC 801-4: 1988–Electrical Transients
•
•
73/23/EEC–Low Voltage Directive (EMC)
EN 60950– Safety of ITE Equipment
•
FCC–47 CFR, Part 15, Subpart B, Class B
Additional applicable standards:
•
•
NEMA Type 1
IP 30
6
Pelco Manual C551M (4/98)
3.0 INSTALLATION
3.1 POWER
No power on/off switch is provided. To apply power: insert the wall mount trans-
former plug into the 12 VAC power jack in the rear panel and insert the wall mount
transformer into a 120 VAC power source (230 VAC with KBD9000-X).
3.2 VIDEO INPUT
Connect a good grade of video coaxial cable from the Coaxitron® receiver or manual
video switcher to the video “IN” BNC connector on the rear panel of the KBD9000.
NOTE: Refer to Table A for the
type of video coaxial cable to use.
Table A. Video Coaxial Cable Requirements
Cable Type*
Maximum Distance
RG59/U
RG6/U
RG11/U
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m)
* Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
3.3 VIDEO OUTPUT
Connect a good grade of video coaxial cable from the video “OUT” BNC connector
on the rear panel of the KBD9000 to the video input of the monitor. This cable
should be terminated in 75 ohms at the monitor, or if looped through the monitor,
terminated at the far end of the run.
3.4 SYSTEM CONFIGURATIONS
The simplest system configuration utilizing the KBD9000 is shown in Figure 1. Ba-
sic KBD9000 Configuration. This system consists of the KBD9000 control transmit-
ter, coax cable and receiver/camera. This basic Coaxitron® system is flexible and
can be expanded to control multiple camera sites when a hard contact switching
device is added. In this configuration, the Hi-Z/75-ohm switch on the back of the
KBD9000 is set to the 75-ohm position.
The addition of a manual video switcher and one receiver/camera is shown in
Figure 2. KBD9000 with Manual Video Switcher and Multiple Cameras. In this
example, the active coaxial cable is terminated in the KBD9000 and the inactive
cables are terminated in the switcher. The selected camera signal is fed to the
KBD9000, which then feeds the monitor. When a camera selection is made, that
video line is dedicated to the KBD9000 and allows the associated Coaxitron®
receiver to be controlled. Functions such as auto/random are latching and will
remain on until turned off by the KBD9000. In this configuration, the Hi-Z/75-ohm
switch on the back of the KBD9000 is set to the 75-ohm position.
KBD9000 basic interconnections between the KBD9000 and receiver are shown in
Figure 3. If you have chosen a configuration that includes a switching device, refer
to the manual provided with the switcher for the appropriate connections.
Pelco Manual C551M (4/98)
7
MONITOR
(TERMINATED)
COAXIAL
CABLE
VIDEO
SIGNAL
COAXITRON®
RECEIVER
MULTICONDUCTOR
CABLE
KBD9000
Figure 1. Basic KBD9000 Configuration
MONITOR
(TERMINATED)
VIDEO
SIGNAL
COAXIAL
CABLE
COAXITRON®
RECEIVER
MULTICONDUCTOR
CABLE
MANUAL
SWITCHER
VIDEO
SIGNAL
KBD9000
COAXITRON®
RECEIVER
MULTICONDUCTOR
CABLE
Figure 2. KBD9000 Configuration with Manual Video Switcher and Multiple Cameras
8
Pelco Manual C551M (4/98)
RECEIVER VIDEO CABLE
INPUT FROM CAMERA
RECEIVER
RECEIVER VIDEO CABLE
OUTPUT TO KBD9000
RECEIVER CONTROL OUTPUT
TO PAN AND TILT/LENS
(AMP SERIES CPC OUTPUT CONN)
24/120/230 VAC
DC
POWER
INPUT
HiZ
75Ω
IN
OUT
OUTPUT TO
MONITOR
INPUT FROM
RECEIVER
Figure 3. Basic KBD9000 Configuration Interconnect Diagram
Pelco Manual C551M (4/98)
9
The Figure 4 drawing, KBD9000 Configuration with Multiple Transmitter and Re-
ceivers, shows a more complex system. In this example, multiple KBD9000 trans-
mitters are controlling multiple receivers.
Video cables from the receivers are looped through the first control station to the
second. At the first control station, a bridging-looping type sequential switcher is
used and the Hi-Z/75-ohm switch on the back of the KBD9000 is set to the Hi-Z
position. At the second control station, a terminating switcher is used and the Hi-Z/
75-ohm switch on the back of the KBD9000 is set to the 75-ohm position.
NOTE: All but the last KBD9000
transmitter and associate switcher
must be looping and unterminated.
Transmitters and associated
switchers should be physically ad-
jacent to prevent signal deteriora-
tion due to cable mismatch.
Any one KBD9000 transmitter can assume control. If two or more KBD9000 control
units are activated simultaneously, erroneous responses are prevented by error
detection circuitry in the associated receiver.
MONITOR
(TERMINATED)
COAXIAL
CABLE
VIDEO
SIGNAL
COAXITRON®
RECEIVER
LOOPING
SWITCHER
MULTICONDUCTOR
CABLE
KBD9000
VIDEO
SIGNAL
COAXITRON®
RECEIVER
TERMINATING
SWITCHER
MULTICONDUCTOR
CABLE
KBD9000
COAXIAL
CABLE
MONITOR
(TERMINATED)
Figure 4. KBD9000 Configuration with Multiple Transmitters and Receivers
10
Pelco Manual C551M (4/98)
4.0 OPERATION
In general, all operating controls on the KBD9000 are self-explanatory. See Section
4.2, KBD9000 CONTROLS, for more information about each control function.
4.1 FUNCTIONAL CIRCUIT DESCRIPTION
The basic functional concept of a Coaxitron® system feeds 15 control pulses in a re-
verse direction from the KBD9000 control transmitter to the receiver located near each
camera station. These control pulses do not interfere with the video monitor presenta-
tion because they occur during the vertical blanking interval of the video signal.
Coaxial cable impedance matching is assured by the video amplifier in the control
receiver. Proper receiving and termination impedance is likewise assured by the
terminating resistor in the KBD9000 control transmitter. Any equipment placed be-
tween the remote and local locations must be of the “loop-through” or “bridging”
type; line amplifiers cannot be tolerated.
Response time of the system is normally less than 30 ms. Error detection circuitry
is incorporated to immunize the system from externally generated noise. Under
extremely adverse environmental noise conditions response time may increase and
control functions can fail. Under such extreme conditions, however, provision is
made to inhibit all momentary functions.
The proper function of the Coaxitron® system depends on the compatibility of two
signals simultaneously traveling in opposite directions in the same coaxial cable. If
the control signal is made large, compared to the video signal, there is the risk that
associated equipment will be adversely affected. If the control signal is made small,
compared to the video signal, it becomes difficult to separate it from the video
signal (and any incumbent noise or hum). Therefore, the Coaxitron® system is de-
signed to function with video and control signals nominally equal.
Under such circumstances, reliable performance can be predicted with cable lengths
up to 1,500 feet (457 m). Beyond this distance, the control signal amplitude can
become attenuated sufficiently to make performance marginal. Marginal performance
is also approached if the video signal is allowed to become excessive — the dy-
namic range of the receiver video amplifier is one limitation. Sending end distortion,
produced by the coaxial cable, is typically the major contributor to the malfunction-
ing of a Coaxitron® system. The amplitude of distortion products is proportional to
video signal amplitude and is a nonlinear function of cable length. The influence of
these distortion products upon system performance is difficult to predict if signal
amplitude is allowed to exceed specifications.
Normally, auto-iris functions will maintain a video level well within reasonable limits
and assure reliable performance. Often, however, automatic or manual level settings
may be made abnormally high (perhaps to compensate for long cable losses or to
produce a picture with more contrast). An excessively high video level setting can
cause the Coaxitron® control system to fail completely — with all control functions
disabled. In order to prevent system failures due to excessively high video levels, it
is recommended that cameras be powered by the receiver.
The KBD9000 is designed to combat prolonged loss of control due to the condi-
tions described previously by providing the following protective functions:
1. Simultaneous commands from two different sources are processed to assure
that manual iris control cannot be inadvertently selected in place of automatic
control.
2. A sustained (20 to 40 second) illegal command condition results in (a) camera
off, (b) automatic iris, or (c) manual pan.
These functions greatly reduce the possibility of loss of control and usually elimi-
nate the need for service.
Pelco Manual C551M (4/98)
11
As an example, assume that the operator switches to manual iris control and pro-
ceeds to open the iris excessively. The result can be a complete loss of control.
Within 20 to 40 seconds, camera power is automatically removed (assuming this
feature exists) and auto iris is reinstated.
4.2 KBD9000 CONTROLS
Refer to Figure 5. KBD900 Control Buttons to better understand the KBD9000 con-
trols.
The KBD9000 has the following controls:
Camera Power
Aux 1,2
Two push-buttonswitchesforOn/Offcontrol(latchingfunction)
Two push-button switches for latching functions
Aux 3, 4
Pan
Two push-button switches for momentary functions*
Two push-button switches for Auto/Man pan control (latching
function)*
Focus
Zoom
Iris
Two push-button switches for Near/Far focus control.
Two push-button switches for Tele/Wide zoom control.
Two push-button switches for Open/Close iris control.
Four push-button switches for Pan/Tilt control.
Pan/Tilt
*External requirements are needed for operation (refer to receiver manual).
CAMERA
ON
OFF
AUX
PAN
AUTO
MAN
1
3
4
2
ZOOM
TELE
WIDE
KBD9000
PAN/TILT
®
Figure 5. KBD9000 Control Buttons
12
Pelco Manual C551M (4/98)
5.0 TROUBLESHOOTING
If you experience operating problems with either the receiver or the KBD9000, first
check all receiver fuses and voltage readings to make sure they are in working
order. The Pelco CX900TLC Local Test Board Plug-in Module can be utilized to
verify that receiver functions and accessories are operational.
There is little that can be done without the aid of an oscilloscope. We recommend
you contact your local dealer or our Customer Service Department for assistance.
Pelco Manual C551M (4/98)
13
6.0 MAINTENANCE
The KBD9000 is engineered to provide years of reliable service. Regularly sched-
uled maintenance is not required. Clean the outer surface of the KBD9000 with a
nonabrasive cleaning cloth and antistatic cleaner. Be sure not to get any cleaner
inside the KBD9000 case.
14
Pelco Manual C551M (4/98)
7.0 SPECIFICATIONS
ELECTRICAL
Input Voltage:
12 VAC from a 120 VAC, 60 Hz wall transformer provided with
unit (230 VAC, 50 Hz with KBD9000-X)
Power
Consumption:
Connectors:
2.5 vA
Two video BNC connectors (video input and output)
Input Impedance: 75 ohms or high impedance (Hi Z), switchable
Control Method:
15-pulse train (pulse width modulated) superimposed on the
videosignalduringtheverticalblankingintervalbytheKBD9000
control transmitter. Pulse train occupies 1 TV line period.
Approximately 1 Vp-p added to video signal, 333 kHz nominal
Pulse Amplitude:
Input Video
Level:
1 Vp-p nominal; 2 Vp-p maximum at less than 75% APL;
1.5 Vp-p maximum at 90% APL
System
Bandwidth:
Less than 2 dB down at 10 MHz (exclusive of cable)
GENERAL
Construction:
Finish:
Environment:
Dimensions:
Weight:
Aluminum
Gray polyester powder coat
Indoor; -10° to 120°F (-23° to 49°C)
See Figure 6.
Unit
Shipping
1.95 lb (0.90 kg)
5.0 lb (2.27 kg) approximate
Rating:
NEMA 1
(Design and product specifications subject to change without notice.)
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
8.10 (20.57)
2.21
(5.61)
HiZ
CAMERA
AUX
PAN
75Ω
IN
OUT
7.16
(18.19)
KBD9000
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES
Figure 6. KBD9000 Dimension Drawing
Pelco Manual C551M (4/98)
15
8.0 WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X,
CC3751H-2,CC3651H-2X,MC3651H-2,andMC3651H-2Xcameramodels,whichhaveafive-
year warranty.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed
dome products.
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Sixmonthsonallpanandtilts,scannersorpresetlensesusedincontinuousmotionapplications
(that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
AllgoodsrequiringwarrantyrepairshallbesentfreightprepaidtoPelco,Clovis,California.Repairs
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
totheProductsshallnotexceedthepricepaidbytheDealertoPelcoforsuchProducts. Innoevent
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss
of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
Ifawarrantyrepairisrequired, theDealermustcontactPelcoat(800) 289-9100or(559)292-1981
to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.
Methodofreturnshipmentshallbethesameorequaltothemethodbywhichtheitemwasreceived
by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number
and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Endura and ExSite are trademarks of Pelco.
© Copyright 1998, Pelco. All rights reserved.
16
Pelco Manual C551M (4/98)
|