Pelco Door W M 5000 Series User Manual

I N S T A L L A T I O N  
WM5000 Series  
Wall Mount Kit  
For Endura® Modules  
C1616M-A (1/08)  
 
Description  
With a WM5000 Series wall mount kit, you can attach up to four Endura modules to the wall in any orientation. The WM5001-4U is a base kit  
consisting of a wall bracket and a module sleeve with a cover plate.  
WARNING: Do not attach more than four module sleeves with modules. The excessive weight can cause the equipment to fall from the  
wall.  
Expansion kits are available if you want to add more module sleeves to a wall bracket. The WM5001-4UEXP expansion kit consists of an  
additional module sleeve.  
The wall bracket and module sleeve interlock are secured with two 4-40 screws, which are located on the module sleeve. Module sleeves attach  
to one another in the same way. The wall bracket can support up to four module sleeves.  
Rubber feet are attached to the wall bracket giving you the option of desktop placement for stacking the modules.  
MODELS  
WM5001-4U  
WM5001-4UEXP  
Wall mount base kit for a single module  
Wall mount expansion kit for an additional module  
C1616M-A (1/08)  
3
 
Installation  
PACKAGE CONTENTS  
WM5001-4U  
1
1
Wall bracket  
Module sleeve with cover plate  
WM5001-4UEXP  
Module sleeve  
1
MOUNTING A WALL BRACKET  
You can mount a wall bracket onto a wall so that the modules can be inserted into the sleeves from the right, left, top, or bottom.  
NOTE: The back of the wall bracket has four rubber feet for placing the mount on a desk. The feet do not need to be removed if the mount is  
installed on a wall.  
To mount a wall bracket, follow these steps and refer to Figure 1.  
1. Position the bracket on the wall in your desired orientation.  
2. Drill four holes into the wall.  
3. Secure the wall bracket to the wall using four 8-32 screws with washers (not supplied).  
Figure 1. Wall Bracket Mounting  
4
C1616M-A (1/08)  
 
 
ATTACHING A MODULE SLEEVE  
Your base kit comes with a single module sleeve. The optional expansion kits allow you to add more module sleeves.  
WARNING: Do not attach more than four module sleeves with modules. The excessive weight can cause the equipment to fall from the  
wall.  
To attach a module sleeve, follow these steps and refer to Figure 2.  
1. Attach the module sleeve to the wall bracket by inserting the four tabs on the module sleeve into the four openings on the wall bracket.  
2. Remove the two 4-40 screws from location A and screw them into location B.  
You must remove the cover plate on the module sleeve before adding additional module sleeves.  
LOCATION B  
LOCATION A  
LOCATION B  
Figure 2. Module Sleeve Attachment  
REMOVING A COVER PLATE  
To add additional module sleeves, you must remove the cover plate from the supplied module sleeve. Refer to Figure 3.  
Figure 3. Cover Plate Removal  
C1616M-A (1/08)  
5
 
   
INSTALLING A MODULE  
To insert a module, follow these steps and refer to Figure 4.  
1. Insert a module into the module sleeve.  
2. Tighten the thumbscrew on the bottom of the module sleeve to secure the module.  
NOTE: Do not attach a WM5001-4UEXP when either a NET5301T-I or a NET5301T-C is in the WM5001-4U.  
Figure 4. Module Installation  
Specifications  
MECHANICAL  
Number of Slots  
Module Orientation  
Rack Units  
1
Variable  
4
Construction  
Aluminum  
Black  
Mounting  
GENERAL  
Dimensions*  
Mounting  
2.19" D x 7.88" W x 6.69" H (5.56 x 20.02 x 16.99cm)  
Wall or desktop  
Unit Weight  
WM5001-4U  
WM5001-4UEXP  
1.46 lb (0.66 kg)  
0.42 lb (0.19 kg)  
*The dimensions are based on the orientation of the wall mount as shown in Figure 4.  
6
C1616M-A (1/08)  
 
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment.  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelcos liability  
for any claim, whether based on breach of contract, negligence, infringement of  
any rights of any party or product liability, relating to the Products shall not exceed  
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be  
liable for any special, incidental, or consequential damages (including loss of use,  
loss of profit, and claims of third parties) however caused, whether by the  
negligence of Pelco or otherwise.  
Exceptions to this warranty are as noted below:  
Five years on fiber optic products and TW3000 Series unshielded twisted pair  
(UTP) transmission products.  
Three years on Spectra® IV products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
The above warranty provides the Dealer with specific legal rights. The Dealer may  
also have additional rights, which are subject to variation from state to state.  
Three years on DX Series digital video recorders, DVR5100 Series digital video  
®
recorders, DigitalSENTRY Series hardware products, DVX Series digital video  
recorders, NVR300 Series network video recorders, and Endura® Series  
distributed network-based video products.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the  
following information:  
Three years on Camclosure® and Pelco-branded fixed camera models, except  
the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models, which have a five-year warranty.  
1. Model and serial number  
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number  
3. Details of the defect or problem  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8  
Series fixed dome products.  
Two years on Spectra III, Spectra Mini, Esprit®, ExSite®, and PS20 scanners,  
including when used in continuous motion applications.  
If there is a dispute regarding the warranty of a product that does not fall under  
the warranty conditions stated above, please include a written explanation with  
the product when returned.  
Method of return shipment shall be the same or equal to the method by which the  
item was received by Pelco.  
Two years on Esprit and WW5700 Series window wiper (excluding wiper  
blades).  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®)  
displays. The lamp and color wheel will be covered for a period of 90 days. The  
air filter is not covered under warranty.  
RETURNS  
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100  
or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair) and designated return location.  
Two years on Intelli-M® eIDC controllers.  
One year (except video heads) on video cassette recorders (VCRs). Video heads  
will be covered for a period of six months.  
All merchandise returned for credit may be subject to a 20 percent restocking and  
refurbishing charge.  
Six months on all pan and tilts, scanners, or preset lenses used in continuous  
motion applications (preset scan, tour, and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to a Pelco designated location. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Goods returned for repair or credit should be clearly identified with the assigned  
CA or RA number and freight should be prepaid.  
REVISION HISTORY  
Manual #  
C1616M  
C1616M-A  
Date  
4/05  
1/08  
Comments  
Original version.  
Added note to Installing a Module section.  
Pelco, the Pelco logo, Camclosure, DigitalSENTRY, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.  
Spectra III is a trademark of Pelco, Inc.  
© Copyright 2008, Pelco, Inc. All rights reserved.  
DLP is a registered trademark of Texas Instruments Incorporated.  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore  
|
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States  
|
|
|
|
|
 

Philips Microcassette Recorder AQ6345 01Z User Manual
Philips Work Light IS F7000 User Manual
Pioneer GPS Receiver AVIC F500BT User Manual
Pioneer Stereo Amplifier PRS D2200T User Manual
Planar Computer Monitor PL1700 User Manual
Planar Projector Accessories UR8450 3D User Manual
Polycom Cordless Telephone Avaya 2490 User Manual
Precor Treadmill 921i User Manual
Primera Technology Network Card PN 510725 121304 User Manual
Psion Teklogix Printer T5000r SR User Manual