Pelco Home Security System C1456M D User Manual

SD5 Series

Spectra^®

(Software Version 3.0)

Dome

Installation/

Operation Manual

C1456M-D (10/98)

Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120

5.11.17 Alarm Pattern ......................................................................46

5.11.18 Zone Blank .........................................................................46

5.11.19 Auto Flip..............................................................................47

5.11.20 Proportional Pan .................................................................47

5.11.21 Limit Stops ..........................................................................48

5.11.21.1 Turning Limit Stops On or Off ............................ 48

5.11.21.2 Programming Limit Stops ..................................48

5.11.22 Park Time Minutes ..............................................................49

5.11.23 Scan Speed ........................................................................49

5.11.24 Pattern Length ....................................................................50

6.0 TROUBLESHOOTING ..............................................................................51

6.1 BACK BOX ELECTRONIC ASSEMBLY REMOVAL..........................52

7.0 MAINTENANCE ........................................................................................53

7.1 DOME CLEANING ............................................................................53

7.2 SERVICE MANUAL ..........................................................................53

8.0 SPECIFICATIONS ....................................................................................54

9.0 WARRANTY AND RETURN INFORMATION ...........................................58

LIST OF ILLUSTRATIONS

Figure

Page

In-Ceiling Components ...................................................................... 9

Back Box Parts ..................................................................................9

Pendant Components .......................................................................10

Compass Tool ...................................................................................14

Conduit Fitting Installation ................................................................14

Installing Back Box............................................................................15

Fastening Back Box ..........................................................................15

Wiring Diagram .................................................................................16

Interconnect Door .............................................................................18

Transformer Wiring ............................................................................19

Interconnect Circuit Board Electrical Connections............................ 19

Switch Locations ...............................................................................21

Lower Dome Installation, In-Ceiling Models......................................27

Lower Dome Installation, Pendant Models........................................28

Backlight Compensation ...................................................................36

SD5 Series Dimension Drawing........................................................54

LIST OF TABLES

Table

Page

Video Coaxial Cable Wiring Distances .............................................17

24 VAC Wiring Distances ..................................................................17

Switch Settings for SW1 ...................................................................21

Switch Settings for SW2 – P-Type Control........................................22

Switch Settings for SW2 – D-Type Control .......................................23

Pelco Manual C1456M-D (10/98)

REVISION HISTORY

Manual # Date

Comments

C1456M

3/97

4/97

Original version.

Added instructions for assembling T-rail clip for metal

panel per ECO 97-134.

C1456M-A

C1456M-B

4/97

5/97

7/97

RevisionA. Added pendant models.

Added standard heater and sun shield.

Added Rev. 2 software features and low-temperature

heater.

9/97

Added note in Sections 3.2 and 5.1 about minimum

voltage requirement. In Section 4.1 added instructions for

sealing pendant dome from moisture. In Section 5.2 added

paragraph about pan/tilt operation with fixed-speed

controllers. Changed the minimum specification for the low-

temperature heater from -40°F (-40°C) to -60°F

(-51°C). Revised input power requirements.

12/97

In Section 1.2.2, added pipe sealant to parts list. In

Section 2.1.2, removed models with an “L” in the suffix;

removed heater kits; moved SD5-SS to Section 2.2. In

Section 2.2, added WX24. In Section 3.2, removed power

requirement for models with standard heater (obsolete);

emphasized that power ratings are “per dome.” In Table B,

removed column for 22-gauge wire. In Table C, removed

references to Spectra^®working with CM9501. In Section

4.1, added note about moisture condensation. In Section

5.3 added note about zoom speed. In Section 5.7, added

patterns for CM6700. In Section 5.8, added note about

using presets without alarms. Added Section 5.11.15.

Revised Section 7.0. In Section 9, revised power and

temperature specifications. Throughout manual, removed

references to RS-485 control.

12/97

4/98

Section 1.1, Important Safeguards and Warnings, up-

dated to include French translation for CUL certification.

C1456M-C

Added Section 1.2, Regulatory Notices. Added in-ceiling

model exploded drawing in Section 1.3.1 and pendant

model exploded drawing in Section 1.3.2. In Section 2.1,

removed reference to standard and low-temperature

heaters. In Section 2.2, removed material on options and

added certification material. In Section 3.1.2, removed

optional metal panel reference in the Caution. Removed

Section 3.1.3 documentation on the optional suspended

ceiling panel and revised Figures 4 and 5 to reflect the

change. Changed the example in Section 3.2 to 90vA from

80vA. Revised Table B. Revised item 1 in Section 3.3 to

remove references to the metal panel. In Section 4.0,

revised the note and the installation instructions to include

information about sealing against moisture and condensa-

tion. In Section 4.2, added reference to pendant conduit

adapter. In Section 5.8, revised the note and documenta-

tion to include additional information and cautioning about

using alarm presets for multiple uses. Added Section 7.2,

Service Manual. Moved Section 8.0, Exploded Assembly

Diagrams to new service manual, C1455SM. Changed

manual pagination.

5/98

Revised Section 4.1 and Figures 3, 14, and 16 because

of modification to top mount.

Pelco Manual C1456M-D (10/98)

C1456M-D

8/98

Manual name changed to Spectra^®(Software Version

3.0). In Section 2.2, revised the certifications. In Section

5.1, added information about selectable power-up mode.

In Section 5.2, revised information about high zoom in

turbo mode. Added Section 5.2.2, Scan Speed. In Section

5.6, added zone blanking information. In Section 5.7,

revised pattern material and added a note. In Section 5.8,

made extensive revisions and additions to material on

alarms. In Section 5.9, added material on programming

for AUX. In Section 5.11, added features to the list and

revised the menu structure. Changed the Main Menu

Access section number from 5.11.15 to 5.11.1, altering all

subsequent 5.11 section numbering. Added the following

sections to document new menu items: 5.11.12 (Power

Up Mode), 5.11.13 (AUX Mode), 5.11.14 (Alarm

Resume), 5.11.15 (Alarm Dwell), 5.11.16 (Alarm Priority),

5.11.17 (Alarm Pattern), and 5.11.18 (Zone Blank). In

Section 5.11.20, revised information about high zoom in

turbo mode. Moved the section on park time minutes

(new number 5.11.22) after the section on limit stops

(new number 5.11.21). Added the following sections to

document new menu items: 5.11.23 (Scan Speed) and

5.11.24 (Pattern Length). Added material in Section 6.0.

In Section 8.0, revised pan speed under Mechanical,

weights under General, and removed NTSC color camera

material under Camera.

10/98

Revised Section 6.0, Troubleshooting.

Pelco Manual C1456M-D (10/98)

(This page intentionally left blank.)

Pelco Manual C1456M-D (10/98)

1.0 GENERAL

1.1 IMPORTANT SAFEGUARDS AND

WARNINGS

1.1 MEASURES DE SECURITE

IMPORTANTES

Prior to installation and use of this product, the following

WARNINGS should be observed.

Avant d’installer ou d’utiliser ce produit, les mesures de

sécurité suivantes sont à prendre:

1. Toute installation et réparation devraient être

entreprises par un technicien qualifié et conformes

au codes locaux.

1. Installation and servicing should only be done by

qualified service personnel and conform to all local

codes.

2. Unless the unit is specifically marked as a NEMA

Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is de-

signed for indoor use only and it must not be installed

where exposed to rain and moisture.

2. A moins que cet equipement indique avoir un boitié

agrée NEMA de type 3, 3R, 3S, 4, 4X, 6 ou 6P, il est

uniquement conçu pour utilisation intérieure et ne

peut donc pas être en contact de pluie ou d’humidité.

3. Only use replacement parts recommended by

Pelco.

3. Utiliser seulement les pièces de rechanges

recommandées par Pelco.

4. After replacement/repair of this unit’s electrical

components, conduct a resistance measurement

between line and exposed parts to verify the ex-

posed parts have not been connected to line cir-

cuitry.

4. Après toute installation ou réparation de la partie

électrique de ce produit, une résistance entre le cou-

rant et la partie exposée devrait être installée afin

de vérifier que la partie électrique n’aie pas été en

contact d’un court circuit.

5. The installation method and materials should be ca-

pable of supporting four times the weight of the en-

closure, pan/tilt, camera and lens combination.

5. L’installation entreprise et le matériel utilisé devraient

supporter quatre fois le poids du boitié, de la tourelle,

de la caméra, et de la lentille.

Ce produit et/ou le manuel pourrait inclurent

les symbols suivants:

The product and/or manual may bear the

following marks:

This symbol indicates that dangerous voltage con-

stituting a risk of electric shock is present within this

unit.

Ce symbol indique qu’un voltage dangereux pouvant

provoquer un chock électrique est présant dans cette

unité.

This symbol indicates that there are important oper-

ating and maintenance instructions in the literature

accompanying this unit.

Ce symbol indique qu’il y a des mesures d’installation

et d’entretient importantes inclus dans le manuel de

cet équipement.

CAUTION:

RISK OF

CAUTION:

RISQUE DE

ELECTRIC SHOCK.

DO NOT OPEN.

CHOQUE ÉLECTRIQUE

NE PAS OUVRIR

CAUTION:

TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DO NOT REMOVE COVER. NO USER-

AFIN DE RÉDUIRE LES RISQUES DE CHOQUE

ÉLECTRIQUE, LE CACHE NE DEVRAIT PAS

ÊTRE RETIRÉ. POUR TOUTE RÉPARATION,

SE RÉFÉRER À UN TECHNICIEN.

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

Please thoroughly familiarize yourself

with the information in this manual prior

to installation and operation.

Nous vous prions de bien vous

familiarisez avec la manuel avant

d’entreprendre toute installation.

Pelco Manual C1456M-D (10/98)

1.2 REGULATORY NOTICES

NOTE: This equipment has been tested and found to comply with the limits of a

Class A digital device, pursuant to part 15 of the FCC rules. These limits are de-

signed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interfer-

ence at his own expense.

1.3 UNPACKING INSTRUCTIONS

Unpack and inspect all parts carefully.

Be sure to save the shipping carton, boxes and inserts. They are the safest material

in which to make future shipments.

If an item appears to have been damaged in shipment, replace it properly in its box

and contact the factory at 1-800-289-9100 or 1-59-292-1981 for a replacement.

(International customers fax 1-559-348-1120 for authorization and instructions.)

If an item needs to be returned to the factory for repair, consult the WARRANTY

AND RETURN section of this manual for instructions.

Pelco Manual C1456M-D (10/98)

1.3.1 In-Ceiling Models

The Spectra^®(Version 3.0) dome shipping carton contains three boxes, plus the

C1456M-D system manual that covers everything in the system (back box, dome

drive, and lower dome). Inspect each box to make sure all parts are present.

Back Box

Back box

Parts bag (refer to Figure 2)

1 Conduit fitting

1 Safety chain bracket

1 Lock nut

1 Compass tool

4 T-rail clip (clip, L-bracket, screw, lock washer and nut)

Installation/Operation Manual (C1488M)

Dome Drive

Dome drive

Installation/Operation Manual (C1490M)

Lower Dome

Acrylic lower dome with trim ring

Installation Instructions (C1457M-B)

COMPASS TOOL

BACK

BOX

SAFETY

BRACKET

DOME

DRIVE

CONDUIT FITTING

& LOCK NUT

T-RAIL CLIP

LOWER

DOME

Figure 1. In-Ceiling Components

Figure 2. Back Box Parts

Pelco Manual C1456M-D (10/98)

1.3.2 Pendant Models

The Spectra^®(Version 3.0) dome shipping carton contains three boxes, plus the

C1456M-D system manual that covers everything in the system (back box, dome

drive, and lower dome). Inspect each box to make sure all parts are present.

Back Box

Back box

Tube of pipe sealant

Installation/Operation Manual (C1488M)

Dome Drive

Dome drive

Installation/Operation Manual (C1490M)

Lower Dome

Acrylic lower dome with trim ring

Parts bag

O-ring

O-ring lubricant

Screw, 6-32 x 1/4" (black) or 6-32 x 5/16" (gray)

Tube of Loctite^®

Installation Instructions (C1457M-B)

BACK

BOX

DOME

DRIVE

LOWER

DOME

Figure 3. Pendant Components

Pelco Manual C1456M-D (10/98)

1.4 RECOMMENDED TOOLS

Pelco does not supply basic tools needed for the installation process. The following

tools are recommended.

To install the back box:

Small flat screwdriver

BNC crimp tool

Wire stripper

Wire cutter

Pen or pencil (in-ceiling models only)

Drill with 3/32-inch drill bit (in-ceiling models only)

Saw to cut hole in ceiling (in-ceiling models only)

Medium Phillips screwdriver (in-ceiling models and pendant surface-mount only)

Drill with hole saw (pendant surface-mount only)

Coaxial cable stripper

To install the dome drive:

To install the lower dome:

None required

Medium Phillips screwdriver (pendant models only)

Pelco Manual C1456M-D (10/98)

2.0 DESCRIPTION

Spectra^®(Version 3.0) domes are capable of the following:

•

360° pan rotation

+2 to -92° tilt

•

preset positioning

variable speed

The in-ceiling models can be installed in hard ceilings or standard 2' x 2' (61 cm x

61 cm) suspended ceilings. These models are for indoor installation only.

The pendant models can be installed indoors or outdoors. The outdoor models

include a sun shield and heater. The heater allows operation in temperatures down

to -60°F (-51°C).

All models include a high-resolution color or monochrome (black and white) cam-

era with a 12X optical, 8X electronic zoom lens for a total zoom ratio of 96X.

An integral receiver has a switch to select the type of control. The receiver supports

Coaxitron^®and RS-422 control types.

The dome drive quickly disconnects from the back box for easy servicing or moving.

The Spectra^®(Version 3.0) domes operate on 24 VAC.

2.1 MODELS

Each Spectra^®(Version 3.0) system consists of one each: back box, dome drive, and

lower dome. Outdoor pendant systems include a sun shield and heater. Refer to

components below (in-ceiling or pendant) to determine your system configuration.

2.1.1 In-Ceiling Components

BB5A-F

DD5-C-X

DD5-M

DD5-M-X

LD5F-0

LD5F-1

LD5F-2

LD5F-3

Indoor back box for flush mounting in a ceiling

Dome drive with color camera/lens, PAL standard

Dome drive with monochrome camera/lens, EIA standard

Dome drive with monochrome camera/lens, CCIR standard

Smoked lower dome (1/2 f-stop of light loss)

Clear lower dome

Chrome lower dome (2 f-stops of light loss)

Gold lower dome (2 f-stops of light loss)

2.1.2 Pendant Components

BB5A-PB

BB5A-PG

BB5A-PG-E

DD5-C-X

DD5-M

Black pendant-mount back box

Light gray pendant-mount back box

Same as BB5A-PG except includes heater and sun shield

Dome drive with color camera/lens, PAL standard

Dome drive with monochrome camera/lens, EIA standard

Dome drive with monochrome camera/lens, CCIR standard

Smoked lower dome (1/2 f-stop of light loss) for black pendant-

mount dome

DD5-M-X

LD5PB-0

LD5PB-1

LD5PB-2

Clear lower dome for black pendant-mount dome

Chrome lower dome (2 f-stops of light loss) for black pendant-

mount dome

LD5PB-3

LD5PG-0

Gold lower dome (2 f-stops of light loss) for black pendant-

mount dome

Smoked lower dome (1/2 f-stop of light loss) for light gray

pendant-mount dome

LD5PG-1

LD5PG-2

Clear lower dome for light gray pendant-mount dome

Chrome lower dome (2 f-stops of light loss) for light gray

pendant-mount dome

LD5PG-3

Gold lower dome (2 f-stops of light loss) for light gray pendant-

mount dome

LD5PG-E0

LD5PG-E1

Same as LD5PG-0 except includes heater

Same as LD5PG-1 except includes heater

Pelco Manual C1456M-D (10/98)

2.2 CERTIFICATIONS

The products identified below have been tested and certified for agency compli-

ance as noted.

Agency Compliance Certification

Model

FCC

CSA/cUL

Spectra^®(Ver. 3) DD5-C-X

Spectra^®(Ver. 3) DD5-M

Spectra^®(Ver. 3) DD5-M-X

Spectra^®BB5A-F

Spectra^®BB5A-PB

Spectra^®BB5A-PG

Spectra^®BB5A-PG-E

Pending

Applicable CE, FCC, UL, and CSA/cUL directives/standards:

• 93/68/ECC–CE Mark Directive

89/336/ECC, 92/31/ECC–Electromagnetic Compatibility (EMC) Directives

EN 55022: 1984 Class A–Radio-frequency emissions limits

EN 50082-2: 1992–Immunity standard

IEC 801-2: 1984–ESD immunity

IEC 801-3: 1984–Radiated field immunity

IEC 801-4: 1988–Electrical transients

• FCC-47 CFR, Part 15, Subpart B, Class A

• UL Listed (DRQH) E119552

• cUL Listed (DRQH7)

Additional applicable standards:

• NEMA Type 4 (except -F flush mount models; NEMA Type 1)

• IP 56 (except -F flush mount models; NEMA Type 10)

Pelco Manual C1456M-D (10/98)

3.0 INSTALLATION FOR IN-CEILING MODELS

To install the dome proceed through the steps in this section, beginning with Sec-

tion 3.1, “Ceiling and Back Box Preparation.”

3.1 CEILING AND BACK BOX PREPARATION

3.1.1 Hard Ceiling

1. Locate the center point where you want to drill a hole in the ceiling.

2. Drill a hole in the ceiling using a 3/32-inch drill bit.

NOTE: Use the SCA1 (structural

ceiling adapter) if additional support

is required.

3. Remove the compass tool from the parts bag that came with the back box

(refer to Figure 4). Press the stud of the compass tool into the hole in the

ceiling. Insert a pencil in the hole in the other end of the compass and mark a

circle on the ceiling.

CAUTION: Be careful

not to cut outside of the

line. If you do, you may not

be able to install the back

box. Also, the trim ring

may not cover the hole.

4. Carefully cut the circle out of the ceiling.

5. Remove the conduit fitting, lock nut, and safety chain bracket from the parts

bag and attach them to the back box as shown in Figure 5.

Proceed to Section 3.2, WIRING.

ATTACH SAFETY CHAIN HERE

Figure 4. Compass Tool

Figure 5. Conduit Fitting Installation

Pelco Manual C1456M-D (10/98)

3.1.2 Suspended Ceiling

1. Remove the ceiling tile from the ceiling.

CAUTION: The ceiling

tile must be capable of

supporting 16 pounds

(7.3 kg) of weight. If the

ceiling tile will not support

this weight, order the

SD5-P metal panel.

2. Locate the center point to drill a hole in the tile.

3. Drill a hole in the ceiling tile using a 3/32-inch drill bit.

4. Remove the compass tool from the parts bag that came with the back box

(refer to Figure 4). Press the stud of the compass tool into the hole in the

ceiling. Insert a pencil in the hole in the other end of the compass and mark a

circle on the ceiling.

CAUTION: Be careful

not to cut outside of the

line. If you do, you may not

be able to install the back

box. Also, the trim ring

may not cover the hole.

5. Carefully cut the circle out of the ceiling tile.

6. Remove the conduit fitting, lock nut, and safety chain bracket from the parts

bag and attach them to the back box as shown in Figure 5.

7. Refer to Figure 6. Compress the spring clips on the back box with your hands

and push the back box through the hole in the ceiling tile. The spring clips will

spring out when they clear the ceiling tile.

8. Refer to Figure 7. Tighten the screws until the spring clips hold the back box

firmly to the ceiling tile. You will hear a clicking noise when the screws are tight.

Do not install the ceiling tile in the ceiling yet.

Proceed to Section 3.2, WIRING.

HARD CEILING

CEILING TILE

Figure 6. Installing Back Box

HARD CEILING

CEILING TILE

T-RAIL CLIP

FOR

CEILING TILE

T-RAIL CLIP

FOR

CEILING TILE

Figure 7. Fastening Back Box

Pelco Manual C1456M-D (10/98)

3.2 WIRING

Bring wiring to the back box opening in the ceiling. Do not attach the wiring to the

back box. You will do that later.

Refer to Figure 8 for the wiring diagram.

Wiring is required for power, earth ground, and video.

Refer to Table A for the type of video coaxial cable to use.

Input power for the dome is 24 VAC only. Power consumption is 25 vA per dome for

indoor models and 90 vAfor outdoor models. Refer to Table B to determine the size

of wire to use.

Use a 24 VAC transformer with the following minimum vA:

NOTE: The dome will stop oper-

ating if the voltage at the dome

drops below 18 VAC. It will turn

back on when the voltage exceeds

18 VAC.

30 vA per dome

100 vA per dome For outdoor models (with heater)

For indoor models (without heater)

Refer to Figure 10 for wiring multiple domes from the same transformer.

If you are using a Coaxitron^®controller, the control signals to operate the dome

drive will be transmitted over the video coax. The RS-422 control lines are not used.

If you are not using a Coaxitron^®controller, use the RS-422 control lines. Use 22-

gauge wire. The distance will be the same as the video coax.

Optional wiring may be provided for alarm inputs (maximum of seven), relay output,

and auxiliary output.

Proceed to Section 3.3, BACK BOX INSTALLATION.

SPECTRA^®(VERSION 3.0) INTERCONNECT BOARD

CONTROL

(RS-422)

+5 to +24 VDC

EXTERNAL RELAY

(WIRING EXAMPLE)

Figure 8. Wiring Diagram

Pelco Manual C1456M-D (10/98)

Table A. Video Coaxial Cable Wiring Distances

Cable Type*

Maximum Distance

RG59/U

RG6/U

RG11/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance. All-copper center conductor. All-copper braided

shield with 95% braid coverage

Table B. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC with a 10-

percent voltage drop. (Ten percent is generally the maximum allowable voltage drop

for AC-powered devices.)

Wire Gauge

EXAMPLE: A dome that requires

90 vA and is installed 31 feet (9 m)

from the transformer would require

a minimum wire gauge of 20 Awg.

283 451 716 1142 1811 2880

(86) (137) (218) (348) (551) (877)

141 225 358 571 905 1440

(42) (68) (109) (174) (275) (438)

113 180 286 457 724 1152

NOTE: Distances are calculated

in feet; values in parentheses are

meters.

(34) (55) (87) (139) (220) (351)

94 150 238 380 603 960

(28) (45) (72) (115) (183) (292)

112 179

285 452 720

(86) (137) (219)

(21) (34) (54)

90 143

228 362 576

(69) (110) (175)

(17) (27) (43)

47 75 119

190 301 480

(57) (91) (146)

(14) (22) (36)

40 64 102

163 258 411

(49) (78) (125)

(12) (19) (31)

35 56 89

142 226 360

(43) (68) (109)

(10) (17) (27)

31 50 79

126 201 320

(38) (61) (97)

(9) (15) (24)

100 28

(8)

45 71

(13) (21)

114 181 288

(34) (55) (87)

110 25

(7)

41 65

103 164 261

(31) (49) (79)

(12) (19)

37 59

120 23

(7)

150 240

(11) (17)

(28) (45) (73)

130 21

(6)

34 55

139 221

(10) (16)

32 51

(26) (42) (67)

140 20

(6)

81 129 205

(9) (15)

30 47

(9) (14)

(24) (39) (62)

76 120 192

150 18

(5)

(23) (36) (58)

160 17

(5)

28 44

71 113 180

(8) (13)

26 42

(21) (34) (54)

67 106 169

170 16

(4)

(7) (12)

(20) (32) (51)

180 15

(4)

25 39

63 100 160

(7) (11)

23 37

(19) (30) (48)

60 95 151

190 14

(4)

(7) (11)

22 35

(6) (10)

(18) (28) (46)

57 90 144

(17) (27) (43)

200 14

(4)

Pelco Manual C1456M-D (10/98)

3.3 BACK BOX INSTALLATION

1. Suspended Ceiling Only (for hard ceiling, go to step 2) – Install the ceiling

tile with the back box. Attach a T-rail clip on each side of the ceiling tile as

shown in Figure 7.

OPTIONAL PROCEDURE: If

you prefer, you may make the wir-

ing connections inside the back box

before installing the back box in the

ceiling.

The clips for the ceiling tile are supplied with the back box. Attach the clip to

the T-rail. Fasten the L-bracket to the clip with the supplied screw, lock washer

and nut.

To do this, loosen the thumbscrew

inside the back box and open the

hinged door (refer to Figure 9).

Bring the wiring into the back box

through the conduit fitting. Follow

the steps in Section 3.4, “Back Box

Connections,” and then return to

this section.

2. Install a safety chain or cable (not supplied) that will support up to 16 pounds

(7.3 kg). Fasten one end to a support structure in the ceiling. Fasten the other

end to the safety chain bracket (refer to Figure 5) to prevent the back box from

falling.

3. Refer to Figure 9. Loosen the thumbscrew inside the back box and open the

hinged door.

4. Bring the wiring into the back box through the conduit fitting. If the wiring is

inside flexible conduit, connect the conduit to the fitting on the back box.

CAUTION: The ceiling

must be capable of sup-

porting 16 pounds (7.3 kg)

of weight. If the ceiling will

not support this weight,

provide additional rein-

forcement. Also, a suit-

able safety chain must be

attached to the back box

to support up to 16

pounds (7.3 kg) in the

event of a ceiling failure.

5. Hard Ceiling Only - Refer to Figure 6. Compress the spring clips on the back

box with your hands and push the back box through the hole in the ceiling. The

spring clips will spring out when they clear the ceiling. Refer to Figure 7. Tighten

the screws until the spring clips hold the back box firmly to the ceiling. You will

hear a clicking noise when the screws are tight.

Proceed to Section 3.4, BACK BOX CONNECTIONS.

THUMBSCREW

Figure 9. Interconnect Door

Pelco Manual C1456M-D (10/98)

3.4 BACK BOX CONNECTIONS

Refer to Figure 11 to attach the wiring to the interconnect circuit board inside the

back box. Also refer to Figure 8 if necessary.

1. Earth Ground - Connect earth ground to the middle connector on the power

connector.

WARNING: Make sure

you wire power to the

outer connectors of the

terminal block and ground

to the middle connector.

Otherwise, you could

damage the dome.

2. Power - Connect 24 VAC from the transformer to the outer terminals on the

power connector. It does not matter which lead goes to which terminal.

If you are wiring more than one dome from the same transformer, it is impor-

tant to wire the power connector in each dome the same way. That is, the

wiring from one side of the transformer must be connected to the same con-

nector on each dome. If you reverse the wiring, the cameras will be out of

phase with each other and may produce what appears to be vertical roll when

switching between cameras. Refer to Figure 10 for a wiring diagram.

3. Video - Connect the coaxial cable to the BNC video connector.

4. Control - If you are using a Coaxitron^®controller, control signals will be trans-

mitted over the video coax.

If you are using RS-422 control signals, connect the control lines from the

controller to the circuit board. Connect the wires as follows:

From controller

To 4-Wire terminal on circuit board

RX-

RX+

TX-

TX+

RX-

RX+

TX+

EXAMPLE: If each

dome requires 20 vA,

three domes require a

60 vA transformer.

CONNECTOR

FOR OPTIONAL

TRANSLATOR

SUBASSEMBLY

HTR/FAN

VIDEO

RS-422

CONTROL

SIGNALS

DOME 1

POWER

RX–

RX+

TX–

TX+

DOME DRIVE

CONNECTOR

GND

COM

AUX 2

GND

DOME 2

POWER

AUX 1

FUSE

FAN

24 VAC

MIDDLE

PIN IS

GND

DOME 3

POWER

(24 VAC ONLY)

1.6 A

Figure 10. Transformer Wiring

Figure 11. Interconnect Circuit Board

Electrical Connections

Pelco Manual C1456M-D (10/98)

5. Heater/Fan - This is a factory connection for a heater on outdoor pendant

models.

NOTE: Connect only a low volt-

age device to the relay output.

Maximum current rating of the re-

lay contacts is two amperes.

6. Alarm Inputs - If you need alarm inputs, connect them. The maximum num-

ber of alarm inputs is seven. Refer to Figure 8 for a typical wiring example.

Alarm inputs require a ground signal through a contact closure, such as a

switch.

7. AUX 1 - An AUX 1 command from the controller will activate the relay output.

If you need the relay, wire it as required. Refer to Figure 8. The relay contacts

are shown when AUX 1 is inactive. When an AUX 1 command is issued, the

relay contacts will reverse and remain latched until a clear command is is-

sued.

CAUTION: The maxi-

mum output of AUX 2 is

150 mA. If you connect a

device that draws more

current, you could destroy

the output transistor. The

output is intended to

drive logic circuits or low-

current devices. If higher

current is required, con-

nect the output to a relay.

8. AUX 2 - An AUX 2 command from the controller will place a ground at the

output of AUX 2 to operate the device connected to it. The output will remain

latched until a clear command is issued. If you need the AUX 2 output, wire it

as required. Refer to Figure 8 for typical wiring examples. TheAUX 2 output is

an open collector transistor driver which is capable of passing a maximum of

150 mAat 32 VDC. It is capable of driving TTL logic circuits or low-current reed

relays. If you use an external relay, make sure that both the supply voltage and

the current requirements are well below the maximum of 32 VDC and 150 mA.

Exceeding these values will cause permanent damage to the dome. If you are

not familiar with open collector drive requirements, contact Pelco technical

support for assistance.

CAUTION: Leave ad-

equate slack in the wiring

to permit the door to open

without pulling on the con-

nectors.

9. Close the door and tighten the thumbscrew securely.

Proceed to Section 3.5, DOME DRIVE.

3.5 DOME DRIVE

NOTE: For Coaxitron^®control,

SW2 is not used and all switches

must be OFF.

1. Turn on power to the back box. The red LED should light to indicate power.

If the LED does not light, correct the trouble before proceeding. Refer to Sec-

tion 6.0, TROUBLESHOOTING.

If the light is operating, you may either leave the power on and continue with

the installation, or you may turn the power off before proceeding further.

2. Set the switches on the bottom of the dome drive. Refer to Figure 12 and Table

C for the settings for SW1.

Refer to Figure 12 and Tables D and E for the settings for SW2.

3. Install the dome drive in the back box: Line up the green drive eject tab on the

dome drive with the green label on the back box and the red static tab with the

red label on the back box. Raise the dome drive into the back box and push on

the ends of the tabs until they both click into place on the back box.

CAUTION: Make sure

the dome drive locks into

place. Tug downward on

the dome drive with mod-

erate pressure to ensure

that it stays in place.

4. Turn on power, if it is not on. Listen for the fan operating. If the fan does not

work, the dome will overheat and shut down. If the fan does not work, return

the back box electronic assembly and dome drive to the factory for repair.

Refer to Section 6.1, BACK BOX ELECTRONIC ASSEMBLY REMOVAL.

Proceed to Section 3.6, LOWER DOME.

Pelco Manual C1456M-D (10/98)

Table C. Switch Settings for SW1

Control Type

Switch Setting

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

Coaxitron^®

P-Type Control

D-Type Control

OFF

OFF*

OFF**

NOTES: Switches SW1-3 through SW1-6 MUST be OFF.

D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500 and CM8500

controllers or with American Dynamics control systems using the AD2083 Translator.

P-type control is RS-422 that is compatible with Pelco’s CM6700/CM9750/CM9760 control systems.

* OFF- Use with controllers that have more than 32 presets.

ON- Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

For CM9502 with fixed speed keyboards, set switch OFF.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

SW 1

OFF

SW 1

SW 2

1 2 3 4 5 6 7 8

OFF

1 2 3 4 5 6 7 8

SW 2

OFF

Figure 12. Switch Locations

Pelco Manual C1456M-D (10/98)

Table D. Switch Settings for SW2 – P-Type Control

NOTES: For Coaxitron^®controls, all switches on SW2 MUST be OFF.

For D-type control systems, refer to Table E.

Receiver Address

Switch Setting

SW2-3

SW2-1

SW2-2

SW2-4

SW2-5

OFF

Baud Rate

Switch Setting

SW2-6

SW2-7

SW2-8

2400

4800

9600

OFF

Pelco Manual C1456M-D (10/98)

Table E. Switch Settings for SW2 – D-Type Control

NOTES: For Coaxitron^®controls, all switches on SW2 MUST be OFF.

For P-type control systems, refer to Table D.

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

Continued on next page

Pelco Manual C1456M-D (10/98)

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

OFF

Continued on next page

Pelco Manual C1456M-D (10/98)

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

OFF

Continued on next page

Pelco Manual C1456M-D (10/98)

Table E. Switch Settings for SW2 - D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

OFF

Continued on next page

Pelco Manual C1456M-D (10/98)

Table E. Switch Settings for SW2 - D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

3.6 LOWER DOME

1. Snap the clip on the end of the trim ring leash into the hole on the lip of the

back box next to one of the mounting screws.

2. Line up the snaps on the trim ring with the mounting screws on the back box.

Snap the trim ring into place on the plastic snap washers on the mounting

screws.

Figure 13. Lower Dome Installation, In-Ceiling Models

Pelco Manual C1456M-D (10/98)

4.0 INSTALLATION FOR PENDANT MODELS

4.1 PENDANT-MOUNT INSTALLATION

1. Install the pendant dome mount. Refer to the instructions supplied with the

mount. If the mount is outdoors, make sure it is properly sealed to keep mois-

ture out.

2. Bring the wiring for the dome through the mount. Refer to Section 3.2, WIR-

ING.

3. Refer to Figure 9. Loosen the thumbscrew inside the back box and open the

hinged door.

4. Screw the back box into the mount and bring the wiring into the back box. If

outdoors, apply the provided pipe sealant to the threads on the back box.

5. Attach the wiring to the back box. Refer to Section 3.4, BACK BOX CONNEC-

TIONS.

NOTE: If outdoors, apply Duct

Seal inside the pipe portion of the

back box to prevent moisture or

cold air inside the mount from en-

tering the unit and causing conden-

sation on the dome. Make sure no

moisture has condensed inside the

unit before installing the lower

dome. Duct Seal can be purchased

through local electrical supply

houses.

6. Install the dome drive. Refer to Section 3.5, DOME DRIVE.

7. Remove the O-ring and O-ring lubricant from the parts bag. Apply lubricant to

the O-ring. Install the O-ring in the groove on the trim ring of the lower dome.

8. Refer to Figure 14. Hanging down from the back box is a short cable (the trim

ring leash). Hold up the lower dome near the back box so that the trim ring

leash touches the lower dome. Line up the two screw holes in the trim ring of

the lower dome with the two screw holes in the back box. Place a finger on the

edge of the trim ring where the leash touches the lower dome.

LEASH

SCREW HOLES

(FRONT & BACK)

ATTACH LEASH

TO NEAREST

RETAINER

SCREW

Figure 14. Lower Dome Installation, Pendant Models

Pelco Manual C1456M-D (10/98)

9. Look inside the lower dome and note which of the six retainer screws is clos-

est to your finger. Remove this screw and attach the trim ring leash to the

screw. Reinstall the screw securely and make sure the leash will hold the

lower dome.

10. If you are installing an outdoor model, plug the two-pin heater connection in

the lower dome into the mating connector in the back box.

11. Remove the two screws and the tube of Loctite^®from the parts bag. Apply a

drop of Loctite^®to each screw.

12. Push the lower dome inside the back box, line up the screw holes, and install

the two screws.

4.2 SURFACE-MOUNT INSTALLATION

NOTE: For hard ceilings, such as

concrete, where the wiring must be

installed in surface-mounted con-

duit, use the optional BB5-PCA-BK

(black) or BB5-PCA-GY (gray) Pen-

dant Conduit Adapter.

1. Use a hole saw to drill a hole in the ceiling where you want to hang the pen-

dant dome.

2. Bring the wiring for the dome to the opening. Refer to Section 3.2, WIRING.

3. Refer to Figure 9. Loosen the thumbscrew inside the back box and open the

hinged door.

4. Remove the gasket and the top mount from the back box by taking out the

three screws and lock washers.

5. Attach the back box to the ceiling using #8 hardware (not supplied). Reattach

the cable (trim ring leash) that was attached to one of the screws you removed

in step 4.

6. Attach the wiring to the back box. Refer to Section 3.4, BACK BOX CONNEC-

TIONS.

7. Install the dome drive. Refer to Section 3.5, DOME DRIVE.

8. Remove the O-ring and O-ring lubricant from the parts bag. Apply lubricant to

the O-ring. Install the O-ring in the groove on the trim ring of the lower dome.

9. Refer to Figure 14. Hanging down from the back box is a short cable (the trim

ring leash). Hold up the lower dome near the back box so that the trim ring

leash touches the lower dome. Line up the two screw holes in the trim ring of

the lower dome with the two screw holes in the back box. Place a finger on the

edge of the trim ring where the leash touches the lower dome.

10. Look inside the lower dome and note which of the six retainer screws is clos-

est to your finger. Remove this screw and attach the trim ring leash to the

screw. Reinstall the screw securely and make sure the leash will hold the

lower dome.

11. If you are installing an outdoor model, plug the two-pin heater connection in

the lower dome into the mating connector in the back box.

12. Remove the two screws and the tube of Loctite^®from the parts bag. Apply a

drop of Loctite^®to each screw.

13. Push the lower dome inside the back box, line up the screw holes, and install

the two screws.

Pelco Manual C1456M-D (10/98)

5.0 OPERATION

NOTE: In the following material,

sometimes a number in parenthe-

ses follows a preset. This second

number is for 32-preset mode.

The red LED in the interconnect door in the back box lights when power is turned

on and the fan operates to exhaust heat from inside the back box.

If you have an outdoor pendant model with a heater, the heater elements in the

back box turn on at 70°F (21°C) and turn off at 85°F (29°C). The heater element in

the lower dome turns on at 40°F (4°C) and turns off at 60°F (16°C). The fans in the

back box operate continuously.

5.1 POWER-UP DISPLAY

When the Spectra^®(Version 3.0) dome is powered up or reset, the selected proto-

col, revision number, and other information is displayed on the monitor. For ex-

ample, the screen might show the following information:

PELCO SPECT II 3.02

CONFIGURE DONE

Protocol C

The information remains on the monitor until the dome is moved. The information

displayed depends on the selected protocol and the choice made on the menu for

selectable power-up mode, a feature that lets the dome resume a desired condition

upon power-up.As a default, the dome goes to a random position. (Refer to Section

5.11.12, POWER UP MODE).

The control system protocol (C, D, or P) appears. C is for Pelco’s Coaxitron^®control

systems. D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500

and CM8500 controllers or with American Dynamics control systems using the

AD2083 Translator. P-type control is RS-422 that is compatible with Pelco’s CM6700

and CM9750/CM9760 control systems.

NOTE: The dome will stop oper-

ating if the voltage at the dome

drops below 18 VAC. It will turn

back on and go through its start-

up routine when the voltage ex-

ceeds 18 VAC.

For the D and P protocols, the device address, baud rate, parity (N), number of data

bits (8), and number of stop bits (1) appears. For the D protocol, if the mode for 32

presets is selected (SW1-7 is ON), “32 presets” appears.

If the CM9500 mode is selected (SW1-8 is ON), “CM9500 mode” appears.

5.2 PAN AND TILT FUNCTIONS

Use the joystick on your controller to control pan and tilt functions.

Pan and tilt operation is at a fixed speed with fixed-speed controllers. The speed is

determined by the controller.

Standard pan operation with variable-speed controllers will range from 0.5 to 80

degrees per second, depending on the position of the joystick. In the turbo mode,

pan speed will be 150 degrees per second. When performing preset operations,

pan speed will be 250 degrees per second.

Standard tilt operation with variable-speed controllers will range from 0.5 to 40 de-

grees per second, depending on the position of the joystick. When performing pre-

set operations, tilt speed will be 100 degrees per second. Turbo mode does not

affect the tilt speed.

If the proportional pan mode is enabled (refer to Section 5.11.20, PROPORTIONAL

PAN), the pan (and tilt) speed will depend on the amount of zoom. At telephoto

zoom settings, the pan (and tilt) speeds will be slower for a given amount of joystick

deflection than at wide zoom settings. This keeps the image from moving too fast on

the monitor when there is a large amount of zoom. This slowing does not happen

when going to a preset, but does occur in turbo mode when high zoom is selected.

Pelco Manual C1456M-D (10/98)

5.2.1 Auto Flip

When the camera tilts downward and goes just beyond the vertical position, the dome

rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward

as long as you continue to hold the joystick in the down position. Once you let go of the

joystick after the dome rotates, joystick control returns to normal operation.The auto-flip

feature is useful for following a person who passes directly beneath the camera.

You can disable this feature in the auto flip programming menu. Refer to Section

5.11.19, AUTO FLIP.

5.2.2 Scan Speed

Scan speed is adjustable from 1 to 40 degrees per second through the program-

ming menu.

5.3 ZOOM

NOTE: On some controllers the

zoom speed can be changed. Re-

fer to the documentation for your

controller.

The Spectra^®(Version 3.0) dome can magnify an object up to 96 times. The dome

has 12X of optical zoom and 8X of electronic (digital) zoom for a total of 96X zoom.

The amount of zoom can be set for 12X, 24X, 48X, or 96X. Software controls the

amount of zoom. Refer to Section 5.11.3, ZOOM LIMIT, to program the zoom limits.

12X or 24X Zoom

Press the Zoom Tele button to magnify an object up to 12 or 24 times. Hold down

the button until the desired picture is obtained.

48X or 96X Zoom

1. Press the Zoom Tele button until the picture reaches 24X zoom.

2. Release the button.

3. Within one second hold down the button again. Hold down the button until the

desired picture is obtained.

5.4 PRESET FUNCTIONS

NOTE: If you are using the Spec-

tra^®(Version 3.0) dome’s alarm in-

puts, presets 1-7 must be reserved

for alarm operations. For more in-

formation, refer to Section 5.8,

ALARMS.

The Spectra^®(Version 3.0) dome is capable of going to 64 preset locations, each

with a 20-character label. The presets are numbered 1-32 and 35-66.

Refer to the documentation for your control system for programming presets.

When a preset operation is performed, the amount of error in moving to the pan and

tilt position a is 1/2 degree. If you command the dome to go to an undefined preset,

erratic operation may result.

NOTE: For AMERICAN DYNAM-

ICS controllers with only 32 pre-

sets, set switch SW1-7 on the

dome drive in the ON position.

When SW1-7 is ON, preset

Presets 33 and 34 are fixed commands, meaning that you cannot program them.

Preset 33 is the “flip” command, which will pan the dome drive 180 degrees from

the position it is at. Preset 34 is the “pan zero” command, which will direct the dome

drive to the factory-determined zero reference point.

The following presets are reserved for special functions:

99 becomes 32

98 becomes 31

97 becomes 30

96 becomes 29

95 becomes 28

93 becomes 26

92 becomes 25

91 becomes 24

90 becomes 23

Preset

Function

Park (Section 5.11.22)

1-7

90-93

Alarms, if used (Section 5.8)

Flip command (Section 5.4)

Pan zero command (Section 5.4)

Limit stops (Sections 5.5 and 5.11.21)

Select camera programming menu (Section 5.11.1)

Stop a scan (Section 5.5)

97-99

Activate scanning (Section 5.5)

If the limit stops are turned off (refer

to Section 5.11.21.1), presets 23-

26 can be used as regular presets.

Pelco Manual C1456M-D (10/98)

5.5 RANDOM, FRAME, AND AUTO SCANNING

Program preset 97 (30) to start random scanning. Program preset 98 (31) to acti-

vate frame scanning (three seconds of scanning followed by a three-second pause).

Program preset 99 (32) to start auto (continuous) scanning.

NOTE: In the following material,

sometimes a number in parenthe-

ses follows a preset. This second

number is for 32-preset mode.

Scan limit stops are controlled by software. Refer to Section 5.11.21, LIMIT STOPS,

to program the scan limit stops.

When the dome reaches a scan limit stop, it will immediately reverse direction.

Program preset 96 (29) to stop a scan. Any pan/tilt or lens command also will stop

a scan.

5.6 ZONES

The Spectra^®(Version 3.0) dome is capable of eight zones, each with a 20-char-

acter label. Depending on the controller, you can define the zone size and define

any zone as “blanked” for video when the camera pans into the zone area. (Zone

sizing and blanking work with the CM8500, CM9500, and MPT9500; but do not

work with the CM6700 and System 9760™.) If zone labels are turned off, the sys-

tem displays the message, VIDEO BLANK, to indicate the video is being blanked

and is not failing. (Refer to Section 5.11.18, ZONE BLANK, for instructions.) For

other information on programming zones, refer to the documentation for your con-

trol system.

5.7 PATTERNS

The Spectra^®(Version 3.0) dome can do either one full pattern (1.5, 3, or 6 minutes

long) or two half patterns (.75, 1.5, or 3 minutes long). (With a CM6700 controller,

the dome can do either two patterns up to 30 seconds long or one pattern up to 60

seconds long.) This pattern can consist of any standard pan and tilt or lens com-

mand. Presets, flip, and turbo are not allowed in a pattern. Zone scan can be en-

abled while running a pattern.

NOTE: Changing the length

erases all stored patterns.

Refer to the documentation for your control system to program and run patterns.

5.8 ALARMS

The Spectra^®(Version 3.0) dome has seven alarm inputs, which can be designated

as either high or low priority through its programming menu. When an alarm is

received, the dome moves to the preset position that corresponds to the alarm

number. For example, if alarm 3 is activated, the dome moves to preset 3. There is

no indication at the controller that an alarm has been received, other than the view

displayed on the monitor.

NOTE: If any of presets 1-7 are

not used for alarms, they can be

used as regular presets. However,

if they are being used for alarms,

they should not be used for any-

thing else.

The high priority setting (if set on the programming menu) is significant when more

than one alarm is activated. If priority in alarms is not required, leave all alarms in

the low setting.

•

If the activated alarm inputs have the same priority–all low or all high–then the

dome will sequence between the presets that correspond to the alarm num-

bers.

•

If the activated alarm inputs have different priorities–for example, one is high

and four are low–the dome goes only to the high. It remains fixed on the high

and only goes to the low after the high has been cleared.

Pelco Manual C1456M-D (10/98)

In certain situations, the dome will respond as follows:

•

If a preset has not been set, but an alarm is connected: the dome will go to a

factory preset that will not be the desired position.

If one alarm is a preset and another is a pattern and both are received: the

dome will alternate between them.

An alarm clears by returning to its former (off) state.

Depending on choices made on the programming menu, the dome can respond to

an alarm by running one of the patterns below. (Refer to Section 5.7, PATTERNS,

for more information.)

•

Run full pattern

Run half pattern 1

Run half pattern 2

When sequencing between presets, the dwell time depends on the time set on the

Alarm Dwell submenu for that preset. After the dwell time expires, the dome imme-

diately does one of the following:

•

If the resume feature was selected on the programming menu and there are

no other alarms activated, the dome resumes its prior activity. So, it might

return to its previous position or resume a scan or pattern.

•

If there are other alarms activated, the dome goes to them.

If you move the joystick to pan or tilt the dome, or if you issue a lens command while

there is an alarm, the pan and tilt or lens command overrides the alarm. Sixty sec-

onds after the last pan and tilt or lens command, the dome will return to the alarm

preset if the alarm is still active.

5.9 AUXILIARY OUTPUTS

An AUX 1 command from the controller will activate the relay in the dome and

operate the device that is connected to the relay. The relay will remain latched until

a clear command is issued.

AnAUX 2 command from the controller will place a ground at the output of AUX 2 to

operate the device that is connected to it. The output will remain latched until a clear

command is issued. Refer to Section 3.4, BACK BOX CONNECTIONS, for precau-

tions regarding the use of the AUX 2 output.

The output relay can also be programmed so that it is activated when any alarm

input is activated. When latching (toggling) is selected on the programming menu,

giving the AUX 1 command from the controller changes the state of the AUX (for

example, if it was on, this turns it off). The clear command from the controller will

turn the AUX off in the latching or toggle mode.

5.10 PARK

If the Spectra^®(Version 3.0) dome does not receive any commands for a specified

period of time (refer to Section 5.11.22, PARK TIME MINUTES), the dome will go to

preset 1 and park. If the time specified is zero, or if preset 1 has not been pro-

grammed, the dome will not park. The default is zero minutes.

Pelco Manual C1456M-D (10/98)

5.11 PROGRAMMING THE SPECTRA™ (VERSION 3.0)

The Spectra^®(Version 3.0) dome can be programmed for the following functions:

AGC (automatic gain control) Auto park time

Power-up mode

Proportional panning

Scan speed

Alarm dwell

Alarm pattern

Alarm priority

Alarm resume

Auto flip disable

Auto focus

Auxiliary relays

Backlight compensation

Camera reset

Gain

Limit stops

Pattern length

Sharpness

Shutter speed

Video zone blanking

White balance

Auto iris

Power line synchronization Zoom limit

The main menu contains six secondary menus:

•

Camera

Line Sync

Power Up Mode

Aux

Alarms, Zone Blank

Other

Each secondary menu has submenus, which are structured as shown below. Be-

side the menu items are section numbers in parentheses showing where the func-

tions are explained.

1. Camera

First Camera Submenu

Backlight comp (5.11.2)

Zoom limit (5.11.3)

Reset camera (5.11.4)

Gain/AGC (5.11.5)

AGC mode

Second Camera Submenu

Shutter speed (5.11.7)

Auto focus mode (5.11.8)

Sharpness (5.11.9)

Auto sharpness

Sharpness

Gain

Auto-iris (5.11.6)

Auto-iris mode

White balance (5.11.10)

Auto white bal

R-B white bal

Auto-iris level

M-G white bal

Auto-iris peak

Prev (to first camera submenu)

Next (to second camera submenu)

2. Line Sync (5.11.11)

Line sync

Line sync phase

3. Power Up (5.11.12)

Power Up

4. Aux (5.11.13)

Aux 1 mode

Aux 2 mode

5. Alarm, Zone Blank

Alarm resume (5.11.14)

Alarm dwell sec (5.11.15)

Alarm priority (5.11.16)

Alarm pattern (5.11.17)

Zone blank (5.11.18)

6. Other

Auto flip (5.11.19)

Proportional pan (5.11.20)

Limit stops (5.11.21)

Park time minutes (5.11.22)

Scan speed deg/s (5.11.23)

Pattern length (5.11.24)

The following sections explain how to program the Spectra^®(Version 3.0) dome

using the menu choices.

Pelco Manual C1456M-D (10/98)

5.11.1 Main Menu Access

You can call up the main menu on your monitor by programming (setting or creat-

ing) preset 95 (28 if in 32-preset mode; refer to Section 5.4).

Programming preset 95 varies according to the type of controller you are using.

Instructions for programming preset 95 are given below for various controllers.

CM6700

1. Enter the number of the Spectra^®(Version 3.0) camera and press the CAM key.

2. Enter 95 and hold the PRESET key for two seconds.

3. In the Edit Preset menu, arrow to SET and press theACK key. The main menu

appears.

CM8500

1. Enter the number of the Spectra^®(Version 3.0) camera and press the CAM key.

2. Highlight PRESET in the Camera menu and hold down the joystick button until

the Set Presets prompt appears.

3. Enter 95 and press the PRESET key. The main menu appears.

CM9500

1. Enter the number of the Spectra^®(Version 3.0) camera and press the CAM key.

2. Press the SELECT key twice.

3. Highlight CAM in the Setup menu and press the SELECT key.

4. Highlight PRESET in the Camera menu and press the SELECT key.

5. Enter 95 and press the F1 key. The main menu appears.

CM9750

1. Turn the KEY SWITCH to the ON position.

2. Press the PROG key. PROGRAM appears on the LCD display.

3. Press the PRES key. The PRESET prompt appears.

4. Enter 95 and press the ENTER key. The main menu appears.

5. Turn the KEY SWITCH to the OFF position.

CM9760

1. In the default menu, select DEF. The Define Submenu appears.

2. Enter your four-digit PIN.

3. Enter 95 and select PRST. The main menu appears on the monitor.

4. Select the Quit icon to return to the default menu.

MPT9500

Standard Coaxitron^®Mode

1. Enter 95 and press the PRESET SET key.

2. Position the asterisk in the YES row and press the F1 key. The main menu

appears.

Extended Coaxitron^®or RS-485 Mode

1. Enter 95 and press the PRESET SET key.

2. Press the F2 key. The main menu appears.

Pelco Manual C1456M-D (10/98)

5.11.2 Backlight Compensation

There are two backlight compensation modes: on and off.

Backlight compensation allows the Spectra^®(Version 3.0) dome to compensate for

bright light behind the object you want to view. With backlight compensation On, the

Spectra^®(Version 3.0) dome will use only the center 10 percent of the picture for

adjusting the iris (refer to Figure 15). If there is a bright light source outside of this

area, it will wash out to white. The camera will adjust the iris so that the object in the

sensitive area is properly exposed.

Non-Sensitive Area

Sensitive

Area

To change the backlight compensation mode:

1. Program Preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

Figure 15. Backlight Compensation

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Backlight Comp.

5. Press the Iris Open button on your keyboard. A star will appear beside Back-

light Comp and the cursor will move to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.3 Zoom Limit

The Spectra^®(Version 3.0) dome can magnify an object up to 96 times. The dome

has 12X optical zoom and 8X of electronic (digital) zoom for a total of 96X zoom.

The amount of zoom can be set for 12X, 24X, 48X, or 96X.

To change the zoom limit:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Zoom Limit.

5. Press the Iris Open button. A star will appear beside Zoom Limit and the cur-

sor will move to the right beside the current zoom limit.

6. Move the joystick up or down to choose the zoom limit.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.4 Reset Camera

Resetting the camera returns the following settings to their defaults.

Setting:

Auto-focus mode

Default:

Auto

Gain/AGC

AGC mode

Gain

Auto

No default setting

Backlight comp

Shutter speed

Auto-iris

Off

Auto

Mode

Auto

Level

Peak

Default value depends on type of camera

White balance

Auto white balance

R-B white balance

M-G white balance

Sharpness

Auto sharpness

Sharpness

No default setting

When the camera is reset, the following settings are not changed: zoom limit, park

time, auto flip disable, limit stops, and proportional panning.

Turning off power to the Spectra^®(Version 3.0) dome does not reset the camera.

Camera settings are retained in memory, and when the power is turned back on,

the settings will be the same as they were when it was turned off.

To reset the camera:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Reset Camera.

5. Press the Iris Open button to reset the camera.

Pelco Manual C1456M-D (10/98)

5.11.5 Gain/AGC

5.11.5.1 AGC Mode

There are three AGC (Automatic Gain Control) modes: auto, on, and off.

In the auto mode, the Spectra^®(Version 3.0) dome automatically adjusts the gain

- the amount of amplification the camera places on its video information in order

to obtain a full 1-volt peak-to-peak video signal out. If the iris is manually opened

to its wide-open position and the picture is weak, the AGC can be turned off and

the gain increased manually to improve the picture. For instructions on how to do

this, refer to Section 5.11.6, AUTO IRIS. When you close the iris, the AGC will

turn back on automatically when the lens iris starts closing.

In the on mode the AGC is on all the time.

In the off mode the AGC is off.

To change the AGC mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Gain/AGC.

5. Press the Iris Open button to enter the Gain/AGC submenu.

6. Move the joystick up or down to position the cursor beside AGC mode.

7. Press the Iris Open button on your keyboard. A star will appear beside AGC

mode and the cursor will move to the right beside the word Auto, On, or Off.

8. Move the joystick up or down to position the cursor beside Auto, On, or Off.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.5.2 Gain

The gain adjusts the signal level of the video output. Increasing the gain in low light

conditions will increase the level of noise in the picture.

To change the gain:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Gain/AGC.

5. Press the Iris Open button to enter the Gain/AGC submenu.

6. Move the joystick up or down to position the cursor beside Gain.

7. Press the Iris Open button on your keyboard. Astar will appear beside Gain and

the cursor will move to the right beside the current gain setting (a numeric value).

8. Move the joystick up or down to change the gain. As you change the gain, the

picture on your monitor will get brighter or darker.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.6 Auto Iris

There are three settings for auto iris: mode, level, and peak.

To change the settings for auto iris:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Auto-Iris.

5. Press the Iris Open button on your keyboard. Another menu will appear with

auto-iris mode, level, and peak selections.

6. Move the joystick up or down to position the cursor beside one of the choices.

Press the Iris Open button on your keyboard.

MODE - The cursor moves to one of two choices: Auto or Off. In theAuto mode, the

iris is automatically adjusted to produce a constant video output as determined by

the Level setting below. In the Off mode, auto iris is disabled, and control is always

manual. Move the joystick up or down to toggle betweenAuto and Off. Press the Iris

Open button to select the choice, or press the Iris Close button if you do not want to

change the setting.

LEVEL - The cursor moves to a numeric value, which the Spectra^®(Version 3.0)

dome uses to try to maintain a certain light level. Changing the value of the Level

setting will change the video level to which the auto iris adjusts. This setting should

be adjusted if the video level in the auto iris mode is too bright or too dark. Move the

joystick up or down to a value. Press the Iris Open button to select the value, or

press the Iris Close button if you do not want to change the setting.

PEAK - The cursor moves to a numeric value. Increasing this value will cause the

auto iris circuit to react more to highlights or “peaks” in the picture. Decreasing this

value will cause it to use the average video level to adjust the iris. Move the joystick

up or down to a value. Press the Iris Open button to select the value, or press the

Iris Close button if you do not want to change the setting.

If auto iris is in the auto mode, it remains that way until you manually open or close

the iris. The dome will return to auto iris when it is panned or tilted more than 15

degrees.

If there is not enough light for a good picture when the iris is wide open, you can

increase the gain of the camera to improve the picture. To do this:

1. The AGC mode (Section 5.11.5.1, AGC MODE) must be in either the Auto or

Off mode. The following steps will not work if the AGC mode is On.

2. Hold down the Iris Open button until the iris is wide open.

3. Release the button.

4. Within one second, hold down the button again. This will start increasing the

camera gain. Hold down the button until a desirable picture is obtained or the

maximum gain is reached.

Pelco Manual C1456M-D (10/98)

5.11.7 Shutter Speed

There are nine electronic shutter speed settings:

Auto

1/100

1/120

1/500

1/1000

1/2000

1/4000

1/10,000

1/30,000

In the Auto setting the camera controls the shutter speed automatically.

Increasing the shutter speed lowers the light sensitivity, but rapidly moving objects

will be less blurred as the speed is increased.

To change the electronic shutter speed settings:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

5. Press the Iris Open button to go to the next camera submenu.

6. Move the joystick up or down to position the cursor beside Shutter Speed.

7. Press the Iris Open button on your keyboard.

8. A star will appear beside Shutter Speed and the cursor will move to the right

beside the current shutter speed.

9. Move the joystick up or down to choose the shutter speed.

10. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.8 Auto-Focus Mode

There are two auto-focus modes: auto and off.

If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will

place the focus in the manual mode. The dome will return to auto focus if you pan or

tilt the unit or do a zoom function.

If the mode is set to off, the dome will operate in the manual mode with one excep-

tion. If you issue a command to go to a preset, auto focus will turn on and remain on

until you press the Focus Far or Focus Near button.

To change the mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

5. Press the Iris Open button to go to the next camera menu.

6. Move the joystick up or down to position the cursor beside Auto-Focus Mode.

7. Press the Iris Open button on your keyboard. A star will appear beside Auto-

Focus Mode and the cursor will move to the right beside the word Auto or Off.

8. Move the joystick up or down to toggle between Auto and Off.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.9 Sharpness

There are two modes for adjusting the sharpness of the picture: automatic and manual.

To change the mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

Press the Iris Open button to go to the next camera menu.

6. Move the joystick up or down to position the cursor beside Sharpness.

7. Press the Iris Open button. Another menu will appear with the auto sharpness

and sharpness selections.

8. Move the joystick up or down to position the cursor beside one of the choices.

Press the Iris Open button.

AUTO SHARPNESS - The cursor moves to one of two choices: On or Off. Move the

joystick up or down to toggle between them. Press the Iris Open button to select the

choice, or press the Iris Close button if you do not want to change the setting.

SHARPNESS - The cursor moves to a numeric value. Move the joystick up or down

to a value. As you change the value, you will see the sharpness change. Press the

Iris Open button to select the value, or press the Iris Close button if you do not want

to change the setting. If the Auto Sharpness is on, it will change to off when you

select a new value.

Pelco Manual C1456M-D (10/98)

5.11.10 White Balance (Color Cameras Only)

There are three settings for white balance: auto, red-blue, and magenta-green.

To change the white balance settings:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position

the cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

5. Press the Iris Open button to go to the next camera submenu.

6. Move the joystick up or down to position the cursor beside White Balance.

7. Press the Iris Open button on your keyboard. Another menu will appear with

the auto, red-blue, and magenta-green selections.

8. Move the joystick up or down to position the cursor beside one of the choices.

Press the Iris Open button on your keyboard.

AUTO WHITE BALANCE - The cursor moves to one of two choices: Auto or Off. Move

the joystick up or down to toggle between them. Press the Iris Open button to select the

choice, or press the Iris Close button if you do not want to change the setting.

R-B WHITE BALANCE - The cursor moves to a numeric value. Move the joystick up

or down to a value. As you change the value, you will see the color change on your

monitor. Press the Iris Open button to select the value, or press the Iris Close button

if you do not want to change the setting. If Auto White Balance is on, it will change

to off when you select a new value.

M-G WHITE BALANCE - The cursor moves to a numeric value. Move the joystick

up or down to a value. As you change the value, you will see the color change on

your monitor. Press the Iris Open button to select the value, or press the Iris Close

button if you do not want to change the setting. If Auto White Balance is on, it will

change to off when you select a new value.

Pelco Manual C1456M-D (10/98)

5.11.11 Line Synchronization

You can turn the line synchronization on or off.

If it is on, you can adjust the synchronization of the power line voltage so that it is in

phase with other cameras. If cameras are out of phase with each other, they may

produce what appears to be vertical roll when switching between cameras.

If it is off, the Spectra^®(Version 3.0) dome synchronizes to an internal clock.

To change the line synchronization settings:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Line Sync, move the joystick up or down to

position the cursor beside Line Sync.

3. Press the Iris Open button on your keyboard. Another menu will appear with

the Line Sync and Line Sync Phase selections.

4. Move the joystick up or down to position the cursor beside one of the choices.

LINE SYNC - The cursor moves to one of two choices: On or Off. Move the joystick

up or down to toggle between them.

Press the Iris Open button to select the choice. If you changed to Off, the camera

may reset itself as it adjusts to the new synchronization. If the camera resets, it will

only affect the line synchronization. It willnot change any other camera parameters,

such as auto focus or auto iris.

Press the Iris Close button if you do not want to change the setting.

LINE SYNC PHASE - The cursor moves to a numeric value. Move the joystick up or

down to change the value.

Press the Iris Open button to select the choice. The value represents the phase angle

in tenths of a degree between 0 degrees and 359 degrees. For example, 900 is 90

degrees, 1200 is 120 degrees, and 2400 is 240 degrees. Press the Iris Open button

on your keyboard to select your choice. The Line Sync setting will change to On. The

camera may reset or the picture on your monitor may wiggle when you change the

phase angle. If the camera resets, it will only affect the line synchronization. It will not

change any other camera parameters, such as auto focus or auto iris.

Press the Iris Close button if you do not want to change the setting.

5.11.12 Power Up Mode

This feature lets the dome resume a desired condition following power-up. The

menu includes the following choices:

•

Default–On power-up, the dome goes through a configuration cycle and stops

at zero reference, showing “Configuration Done,” and address and mode set-

tings on the screen.

•

Park–The dome moves to preset 1 when the power-up sequence finishes.

The only text on the screen is the preset label (if any is programmed).

Scan Auto–The dome initiates scan mode when the power-up sequence fin-

ishes. Again, there is no text.

Scan Frame–The dome initiates a frame scan when the power-up sequence

finishes.

Scan Rand–The dome initiates a random scan when the power-up sequence

finishes.

Full Pat–The dome initiates its programmed pattern when the power-up se-

quence finishes. The length can be set to 1.5, 3, or 6 minutes.

Half Pat 1–The dome initiates the first half-pattern when the power-up se-

quence finishes. The length can be set to .75, 1.5, or 3 minutes.

Half Pat 2–The dome initiates the second half-pattern when the power-up

sequence finishes. The length can be set to .75, 1.5, or 3 minutes.

The default setting is Default.

Pelco Manual C1456M-D (10/98)

To select the power-up mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4,PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1). The main

menu will appear.

2. If the cursor (>) is not beside Power Up Mode, move the joystick up or down to

position the cursor beside Power Up Mode.

3. Press the Iris Open button to enter the Power Up Mode submenu.

4. Move the joystick up or down to cycle through the selections. Stop on the item

you want to select.

SELECT – Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.13 AUX Mode

This feature defines the output relay as either Normal (under control of the head

end), Latching (pressing the AUX key turns on the AUX and the next press of the

AUX key turns it off), or Alarm (any alarm input activates the AUX).

To change the AUX mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside AUX, move the joystick up or down to position the

cursor beside AUX.

3. Press the Iris Open button to enter the AUX submenu.

4. Move the joystick up or down to position the cursor next to either Aux 1 mode

or Aux 2 mode.

5. Press the Iris Open button. The cursor will move to the right beside the word

Normal, Latching, or Alarm.

6. Move the joystick up or down to toggle between Normal, Latching, or Alarm.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.14 Alarm Resume

This mode lets the dome resume its previous activity (scan, pattern, or previous

position) after all alarms are cleared.

To change the alarm resume mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or

down to position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Resume.

5. Press the Iris Open button. The cursor will move to the right beside the word

On or Off.

6. Move the joystick up or down to toggle between On or Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.15 Alarm Dwell

This is the minimum time the Spectra^®(Version 3.0) will stay at an alarm even if the

alarm is present for less than this amount of time.

To change the alarm dwell:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or

down to position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Dwell sec.

5. Press the Iris Open button. The cursor will move to the right beside the num-

ber of seconds for the alarm dwell time.

6. Move the joystick up or down and hold to cycle through 1-200 seconds in one-

second increments.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.16 Alarm Priority

This feature lets you set alarm inputs as either high or low priority. A high priority

alarm will not release to a low priority alarm. Alarms will release or sequence be-

tween low priority alarms only if no high priority alarm exists. (Refer to Section 5.8,

ALARMS, for more information.)

To change alarm priority:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or

down to position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Priority.

5. Press the Iris Open button to enter the Alarm Priority submenu.

6. Move the joystick up or down to position the cursor beside the number of the

alarm input for which you want to set the priority.

7. Press the Iris Open button. The cursor will move to the right beside the word

High or Low.

8. Move the joystick up or down to toggle between the words High and Low.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.17 Alarm Pattern

In response to an alarm, the Spectra^®(Version 3.0) dome can do either one full

pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long).

You can choose one of the following for each of the seven alarm inputs:

NOTE:Pattern length is set on the

secondary menu entitled Other.

•

Full Pat (run full pattern)

Half Pat 1 (run half pattern 1)

•

Half Pat 2 (run half pattern 2)

No Pattern

To change the alarm pattern:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or

down to position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Pattern.

5. Press the Iris Open button to enter the Alarm Pattern submenu.

6. Move the joystick up or down to position the cursor beside the number of the

alarm input for which you want to set the pattern.

7. Press the Iris Open button. The cursor will move to the right beside the words

Full Pat, Half Pat 1, Half Pat 2, or No Pattern.

8. Move the joystick up or down to toggle between the choices.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.18 Zone Blank

This feature lets you define any of eight zones as blanked for video when the cam-

era pans into the zone area. The choices are On and Off. On means video blanking

is in effect. The default is Off.

To change the blank zone setting:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or

down to position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Zone Blank.

5. Press the Iris Open button to enter the Zone Blank submenu.

6. Move the joystick up or down to position the cursor beside the number of the

zone for which you want to set the blank option.

7. Press the Iris Open button. The cursor will move to the right beside the word

On or Off.

8. Move the joystick up or down to toggle between the words On and Off.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.19 Auto Flip

There are two auto flip modes: on or off.

When the auto flip mode is on, the auto flip feature is enabled. When it is off, the

feature is disabled.

To change the auto flip mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position

the cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Auto Flip.

5. Press the Iris Open button. A star will appear beside Auto Flip and the cursor

will move to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.20 Proportional Pan

There are two proportional pan modes: on or off.

When proportional pan mode is on, the proportional pan feature is enabled and the

pan (and tilt) speed will depend on the amount of zoom. At telephoto zoom settings,

the pan (and tilt) speeds will be slower for a given amount of joystick deflection than

at wide zoom settings. This keeps the image from moving too fast on the monitor

when there is a large amount of zoom. This slowing does not happen when going to

a preset, but does occur in turbo mode when high zoom is selected.

When the proportional pan mode is off, the feature is disabled and the pan speed

will not depend on the amount of zoom.

To change the proportional pan mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position

the cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Proportional Pan.

5. Press the Iris Open button. Astar will appear beside Proportional Pan and the

cursor will move to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.21 Limit Stops

There are two types of limit stops:

Manual limit stops

Scan limit stops

When manual limit stops are set, a manual (joystick) pan operation will stop when a

limit stop is reached.

When scan limit stops are set, the dome will reverse direction during random, frame,

or auto scanning when a limit stop is reached.

Limit stops are controlled by software. To set limit stops:

1. Turn on the limit stop mode.

2. Program the limit stops.

5.11.21.1 Turning Limit Stops On or Off

To change the limit stop mode:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position

the cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Limit Stops.

5. Press the Iris Open button. A star will appear beside Limit Stops and the cur-

sor will move to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

5.11.21.2 Programming Limit Stops

Manual Limit Stops

NOTE: Programming preset 90

(23) disables the manual limit

stops until preset 91 (24) is set.

1. Make sure the limit stops are turned ON (refer to Section 5.11.21.1, TURNING

LIMIT STOPS ON OR OFF).

2. Program preset 90 (23) for the left manual stop and preset 91 (24) for the right

manual stop. Refer to the documentation for your control system for program-

ming presets. Program preset 90 (23) first and then program preset 91 (24). If

presets 90 (23) and 91 (24) are set for the same point, the manual limit stops

will be disabled.

Scan Limit Stops

1. Make sure the limit stops are turned ON (refer to Section 5.11.21.1, TURNING

LIMIT STOPS ON OR OFF).

2. Program preset 92 (25) for the left scan stop and preset 93 (26) for the right

scan stop. Refer to the documentation for your control system for program-

ming presets. Programming preset 92 (25) disables the scan limit stops until

preset 93 (26) is set. If presets 92 (25) and 93 (26) are set for the same point,

the scan limit stops will be disabled.

Pelco Manual C1456M-D (10/98)

5.11.22 Park Time Minutes

This feature causes the dome to park at preset 1 after a programmed number of

minutes of control inactivity. The time can be set from 1 minute to 720 minutes (12

hours), or it can be set to zero, which disables this feature.

NOTE: Preset 1 must be pro-

grammed for the dome to park.

To change the park time:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET FUNC-

TIONS) to access the main menu (refer to Section 5.11.21.1, TURNING LIMIT

STOPS ON OR OFF). The main menu will appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Park Time Minutes.

5. Press the Iris Open button. A star will appear beside Park Time Minutes and the

cursor will move to the right beside the current park time.

6. Move the joystick up or down to change the park time.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

5.11.23 Scan Speed

The scan speed is adjustable from 1-40 degrees per second. This occurs in three

scan modes: auto, random, and frame scan.

To change the scan speed:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET FUNC-

TIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU AC-

CESS). The main menu will appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

3. Press the Iris Open button to enter the submenu entitled Other.

4. Move the joystick up or down to position the cursor beside Scan Speed deg/s.

5. Press the Iris Open button. The cursor will move to the right beside the number

of degrees.

6. Move the joystick up or down to toggle through the number of degrees (1-40)

until you reach the number you want. (If set on a low number, the scan will

appear to barely move but is still functioning.)

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

5.11.24 Pattern Length

You can set the pattern length to 1.5, 3, or 6 minutes or have two half-patterns of

.75, 1.5, or 3 minutes long.

CAUTION: If the length

is changed, all patterns

that were stored are

erased.

To set the pattern length:

1. Program preset 95 (28 if in 32-preset mode; refer to Section 5.4, PRESET

FUNCTIONS) to access the main menu (refer to Section 5.11.1, MAIN MENU

ACCESS). The main menu will appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position

the cursor beside Other.

3. Press the Iris Open button to enter the submenu entitled Other.

4. Move the joystick up or down to position the cursor beside Pattern Length.

5. Press the Iris Open button. The cursor will move to the right beside the num-

ber of minutes (1.5, 3, or 6).

6. Move the joystick up or down to toggle through the number of minutes (1.5, 3, or

6).

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL- Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1456M-D (10/98)

6.0 TROUBLESHOOTING

NOTE:The dome drive contains no

user-serviceable parts. If there is a

problem with your dome drive, it

must be returned to Pelco as a com-

plete unit for servicing.

Symptom: Unit does not operate.

1. Make sure your controller is trying to communicate with the unit and not an-

other camera.

2. Turn off power.

3. Remove the lower dome:

In-Ceiling Models - Insert the flat blade of a screwdriver into one of the slots on

the trim ring and twist the screwdriver to pop loose the trim ring and lower dome.

Pendant Models - Remove the two screws that hold the trim ring to the back

box. Insert the flat blade of a screwdriver into the slots on the trim ring and

twist the screwdriver to free the lower dome from the back box.

4. Remove the dome drive: Push in on the green drive eject tab on the side of the

dome drive and gently rock the dome drive to release the latch. When the

green latch releases, pull the dome down.

5. Turn on power.

6. If the red power LED on the door of the interconnect circuit board in the back

box does not light, turn off power.

a. Open the door to the interconnect circuit board and check the fuse.

Refer to Figure 9 for the location of the fuse. If the fuse is bad, replace

it. To order a replacement fuse from Pelco, specify the part number

FUS1.6-5X20FAST. This is a 1.6-ampere fuse, 5 x 20 mm, fast blow.

b. If the fuse is good, turn on power and use a voltmeter to check if 24 VAC

is getting to the power connector on the interconnect circuit board. Refer

to Figure 9 for the location of the AC power connector.

c. If there is 24 VAC to the power connector, turn off power and return the

back box electronic assembly to the factory for repair. Refer to Section

6.1, BACK BOX ELECTRONIC ASSEMBLY REMOVAL.

d. If there is no voltage at the power connector, check your power supply.

7. If the red power LED is lit, turn off power.

a. Open the door to the interconnect circuit board and check that all con-

nectors are fully seated.

b. Make sure the wiring is correct between the unit and controller.

c. Close the door. Check the switch settings on the dome drive (refer to

Tables C, D, and E) and reinstall the dome drive.

d. Turn on power. If the unit still does not operate, turn off power and re-

place the dome drive with a unit that is good, if you have a spare. Check

the switch settings on the substitute dome drive before installing it. If you

do not have a spare, return the dome drive to the factory. Also return the

back box electronic assembly. Refer to Section 6.1. BACK BOX ELEC-

TRONIC ASSEMBLY REMOVAL.

e. If you substituted a dome drive, turn on power. If the unit operates, the

original dome drive is bad. Return it to the factory. If the unit still does not

operate, then the interconnect board is bad. Return the back box elec-

tronic assembly to the factory; refer to Section 6.1, BACK BOX ELEC-

TRONIC ASSEMBLY REMOVAL.

Pelco Manual C1456M-D (10/98)

Symptom: Fan does not operate.

1. Turn off power.

2. Remove the lower dome:

In-Ceiling Models - Insert the flat blade of a screwdriver into one of the slots

on the trim ring and twist the screwdriver to pop loose the trim ring and lower

dome.

Pendant Models - Remove the two screws that hold the trim ring to the back

box. Insert the flat blade of a screwdriver into the slots on the trim ring and

twist the screwdriver to free the lower dome from the back box.

3. Remove the dome drive: Push in on the green drive eject tab on the side of the

dome drive and gently rock the dome drive to release the latch. When the

green latch releases, pull the dome down.

4. Make sure the connector for the fan is fully seated.

5. Replace the dome drive. Turn on power. If the fan does not operate, return the

back box electronic assembly and dome drive to the factory for repair. Refer to

Section 6.1, BACK BOX ELECTRONIC ASSEMBLY REMOVAL.

Symptom: Alarms not cycling when more than one alarm is active

Reset all your alarm priorities to all LOW or all HIGH (refer to Section 5.8, ALARMS,

for an explanation of alarm high/low priorities). To reset the alarm priorities:

1. Go to Section 5.11.1, MAIN MENU ACCESS, and follow the instructions for

accessing the programming main menu.

2. Go to Section 5.11.16, ALARM PRIORITY, and follow the instructions for set-

ting the alarm priority.

Symptom: Alarms not going to preset

•

Check that the preset is defined.

Check that no higher priority alarm is activated.

Check that a pattern is not set for the affected alarm(s). If a pattern is set, the

alarm will run a pattern, not go to a preset. If a pattern (or patterns) is set, reset

the pattern(s) to NO PATTERN. To reset a pattern:

1. Go to Section 5.11.1, MAIN MENU ACCESS, and follow the instructions for

accessing the programming main menu.

2. Go to Section 5.11.17, ALARM PATTERN, and follow the instructions for set-

ting the alarm pattern.

Symptom: Alarms not starting a pattern

Ensure that the pattern selected is valid. Any time you expect a pattern to execute,

make sure the pattern is recorded correctly and is valid.

Symptom: Motion problems

When troubleshooting motion problems on a system where alarms are connected,

you can eliminate alarms as a cause of the problem by disconnecting the alarm

block in the back box.

6.1 BACK BOX ELECTRONIC ASSEMBLY REMOVAL

To remove the back box electronic assembly:

1. Turn off power.

2. Open the interconnect door and disconnect all wiring to the back box.

3. Use an 11/32 socket driver to remove the three 8-32 washers and nuts that

hold the electronic assembly to the back box. When the screws are removed,

the interconnect back box receptacle will drop down. It may be necessary to

move the open interconnect door past 90 degrees vertical toward the side of

the back box to release the door from the built-in grounding strip (and free the

interconnect back box receptacle).

4. Remove the interconnect back box receptacle with the electronic components

from the back box.

Pelco Manual C1456M-D (10/98)

7.0 MAINTENANCE

7.1 DOME CLEANING

Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to

scratch the sufaces of the dome.

Exterior Surface - Clean the dome's exterior surface with a nonabrasive cleaning

cloth and cleaning agent that is safe for acrylic. Either liquid or spray cleaner/wax

suitable for fine furniture is acceptable.

Interior Surface (Except Chrome or Gold) - Clean the same as the exterior sur-

face.

Interior Surface (Chrome or Gold) - The inside surface of a chrome or gold dome

is easily scratched. Use the following precautions to maintain the dome's surface.

a. Always handle the dome from the outside of its circular flange.

b. Never touch the coated inside surface. The acid in your fingerprints will even-

tually etch the coating if the fingerprints are not carefully removed according

to the recommended cleaning procedure in item “e”.

c. If dust or other contaminants accumulate on the dome's interior, remove the

debris with compressed air. Compressed air cans are available from photo-

graphic equipment or electronic supply dealers.

d. If heavy residue accumulates and cannot be removed with air pressure, rinse

with water and immediately dry with air pressure so that water spots will not

remain. Avoid wiping the coated surface with direct hand pressure - it will eas-

ily abrade unless extreme care is taken. Once scratched, the dome cannot be

recoated.

e. If internal wiping is necessary, avoid hand rubbing. Instead, make a wick as

follows:

Use a very soft paper towel. Roll a section into a tightly wound tube. Tear the

tube in half, and wet the fuzzy end of the wick with a solution of isopropyl

alcohol diluted with water. Hold the dome with its opening facing downward

and wipe the interior of the dome with the wet end of the wick. Use a circular

motion, starting from the outside and spiraling into the center. Use a new wick

for each two passes over the dome.

7.2 SERVICE MANUAL

If you need to service your unit, obtain a service manual in one of the following

ways:

•

Go to Pelco’s web site at ftp://www.pelco.com and find service manual

C1455SM.

Contact Pelco’s Literature Department and request service manual C1455SM.

Pelco Manual C1456M-D (10/98)

8.0 SPECIFICATIONS

MECHANICAL

Construction

Back box:

Dome drive:

Lower dome:

Cable Entry

In-Ceiling:

Pendant:

Pan Movement:

Vertical Tilt:

Manual Pan Tilt

Speeds*

Aluminum

Aluminum, ABS plastic

Acrylic

.75" (1.91 cm) conduit fitting

Through 1.5" (3.81 cm) NPT pendant mount

360° Continuous pan rotation

Unobstructed +2° to -92°

Pan:

Tilt:

Preset Speeds

Pan:

Tilt

0.5°-80°/sec manual operation, 150°/sec turbo

0.5°-40°/sec

250°/sec

100°/sec

Dimensions:

See Figure 16

* For variable-speed operation an appropriate controller is required. With fixed speed

controllers, Spectra^®(Version 3.0) pan/tilt speed is 24°/sec. The CM6700 controller

with the KBD200 keyboard has programmable fixed speeds.

TOP PORTION OF BACK BOX

IS REMOVABLE FOR SURFACE

MOUNT APPLICATIONS

DOME IS SECURED

TO CEILING BY

MOUNTING BRACKET

7.25 (18.13)

6.60 (16.76)

8.52

(21.64)

5.25

(13.34)

6.75

(17.15)

10.90

27.69

5.83

(14.80)

3.25

(8.26)

5.90 (14.99)

8.25 (20.96)

5.90

(14.99)

PENDANT DOME

IN-CEILING DOME

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

Figure 16. SD5 Series Dimension Drawing

Pelco Manual C1456M-D (10/98)

ELECTRICAL

Input Voltage:

Input Power

In-ceiling:

18-30 VAC, 24 VAC nominal

25 vA

Indoor pendant: 25 vA

Outdoor

pendant:

Fuse:

90 vA

1.6 A

Relay Contacts

AUX 1

AUX 2 Output

Type:

Voltage:

Form C

Low voltage (<40 V)

Open collector transistor output

32 VDC maximum

Current:

2 A maximum

150 mA maximum

GENERAL

Environment

In-Ceiling:

Pendant:

Indoor only

Indoor/outdoor

Operating Range

In-Ceiling:

Pendant

32° to 122°F (0° to 50°C)

Without

heater:

32° to 122°F (0° to 50°C)

With Heater*: -60° to 122°F (-51.11° to 50°C)

continuous operation; minimal icing

-50° to 122°F (-45.56° to 50°C)

continuous operation; prevents icing

-40° to 122°F (-40° to 50°C)

continuous operation; de-ices .1" (2.5 mm)

within three hours after power-up

Weight

In-Ceiling

Unit

Shipping

Back Box

Dome Drive

Lower Dome

Pendant

2.6 lb (1.18 kg)

2.65 lb (1.20 kg)

.19 lb (.09 kg)

4 lb (1.81 kg)

5 lb (2.27 kg)

1 lb (.45 kg)

Back Box

2.85 lb (1.28 kg)

5 lb (2.27 kg)

Add 1.25 lbs (.57 kg) for heater and sun shield

Dome Drive

Lower Dome

2.65 lb (1.20 kg)

1.30 lb (.59 kg)

5 lb (2.27 kg)

2.20 lb (1.0 kg)

Add .25 lbs (.11 kg) for heater

* Assumes no wind chill factor; for detailed test conditions, contact Pelco.

CAMERA

COLOR

Signal Format:

PAL

Scanning System: 2:1 interlace

Image Sensor

PAL:

1/4-inch interline transfer

Total pixels: 795 (H) x 596 (V)

Effective pixels: 752 (H) x 582 (V)

460 TV lines

Resolution:

Lens

Minimum f/stop: F/1.6

Focal Length:

Zoom Ratio:

Horizontal

4 to 48 mm

12X optical zoom, 8X electronic zoom

Angle of View: 47° (at 4 mm wide zoom), 4° (at 48 mm telephoto zoom)

MTBF:

Focus:

>2 million cycles at room temperature (zoom, focus, iris)

Automatic

Sensitivity:

4 lux at f/1.6 at signal level of 300 mv (PAL), gain high

Signal Process:

Sync System:

White Balance:

Shutter Speed:

Iris Control:

Gain Control:

Video Output:

Signal to Noise:

DSP III

AC line lock, phase adjustable via remote control*

Automatic with manual override*

Automatic (electronic iris)/manual; 1/50-1/30,000 (PAL)*

Automatic with manual override*

PAL -.7 V ±.07 V

>46 dB

* Manual control over camera setup functions depends on the head end and is not

available on all control models.

Pelco Manual C1456M-D (10/98)

BLACK AND WHITE

Signal Format:

EIA/CCIR

Scanning System: 2:1 interlace

Image Sensor

EIA:

1/4-inch interline transfer

Total pixels: 537 (H) x 505 (V)

Effective pixels: 510 (H) x 492 (V)

Total pixels: 537 (H) x 597 (V)

Effective pixels: 500 (H) x 582 (V)

380 TV lines

CCIR:

Resolution:

Lens

Minimum f/stop: F/1.6

Focal Length:

Zoom Ratio:

Horizontal

4 to 48 mm

12X optical zoom, 8X electronic zoom

Angle of View: 47degree (at 4 mm wide zoom), 4degree (at 48 mm telephoto

zoom)

MTBF:

Focus:

>2 million cycles at room temperature (zoom, focus, iris)

Automatic

Sensitivity:

0.5 lux at f/1.6 at signal level of 40 IRE (EIA)/300 mv (CCIR),

gain high

Signal Process:

Sync System:

Shutter Speed:

DSP III

AC line lock, phase adjustable via remote control*

Automatic (electronic iris)/manual; 1/60 – 1/30,000 (EIA); 1/50-

1/30,000 (CCIR)*

Iris Control:

Automatic with manual override*

EIA - .714 V ±.07 V (100 IRE ±10 IRE); CCIR -.7 V ±.07 V

>46 dB

Gain Control:

Video Output:

Signal to Noise:

* Manual control over camera setup functions is dependent on the head end and is

not available on all control models.

(Design and product specifications subject to change without notice.)

Pelco Manual C1456M-D (10/98)

NOTES

Pelco Manual C1456M-D (10/98)

9.0 WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

•

Five years on FT/FR8000 Series fiber optic products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

Three years on Camclosure^®and fixed camera models, except the CC3701H-2, CC3701H-2X,

CC3751H-2,CC3651H-2X,MC3651H-2,andMC3651H-2Xcameramodels,whichhaveafive-

year warranty.

•

Two years on standard motorized or fixed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed

dome products.

•

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 scanners, including when used in

continuous motion applications.

•

Two years on Esprit^®and WW5700 Series window wiper (excluding wiper blades).

Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura^™Series distributed network-based video products.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

Sixmonthsonallpanandtilts,scannersorpresetlensesusedincontinuousmotionapplications

(that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.

AllgoodsrequiringwarrantyrepairshallbesentfreightprepaidtoPelco,Clovis,California.Repairs

made necessary by reason of misuse, alteration, normal wear, or accident are not covered under

this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the

specific use or application made of the Products. Pelco’s liability for any claim, whether based on

breach of contract, negligence, infringement of any rights of any party or product liability, relating

totheProductsshallnotexceedthepricepaidbytheDealertoPelcoforsuchProducts. Innoevent

will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss

of profit and claims of third parties) however caused, whether by the negligence of Pelco or

otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

Ifawarrantyrepairisrequired, theDealermustcontactPelcoat(800) 289-9100or(559)292-1981

to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty

conditions stated above, please include a written explanation with the product when returned.

Methodofreturnshipmentshallbethesameorequaltothemethodbywhichtheitemwasreceived

by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)

289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,

and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number

and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed

to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco, the Pelco logo, Camclosure, Esprit,

Genex, Legacy, and Spectra are registered

trademarks of Pelco.

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

Endura and ExSite are trademarks of Pelco.

Pelco Manual C1456M-D (10/98)

Pelonis Electric Heater HC 0113 User Manual
Philips Blu ray Player BDP3200 User Manual
Philips Car Stereo System 15PT2302 User Manual
Philips Cell Phone Cordless Telephone Dual Band User Manual
Philips Cordless Telephone KX TG2205 User Manual
Philips CRT Television 14PT2104 User Manual
Philips Home Theater System HTS3151D User Manual
Philips Speaker System AW3000 User Manual
Pioneer Network Card DVR 216D User Manual
PVI Industries Water Heater 140P175A E User Manual