Pelco Home Security System C2494M User Manual

I N S T A L L A T I O N  
Spectra IIIEVS  
In-Ceiling Back Box  
C2494M (12/05)  
 
Installation  
Locate the center point of the mounting location and insert the compass  
tool. Draw a circle.  
1
Cut the circle out of the ceiling.  
Attach the conduit fitting, safety chain bracket, and lock nut. Install a  
safety chain/cable (not supplied) that will support up to 16 pounds  
(7.3 kg).  
2
3
Open the hinged door to the back box. Push the tab lock towards the  
wall of the unit and lift the door open. Pull power, alarm/auxiliary, and  
network cable into the back box.  
The following are the recommended maximum distances for 24 VAC  
applications and are calculated with a 10 percent voltage drop.  
(Ten percent is generally the maximum allowable voltage drop for  
AC-powered devices.)  
Total  
VA  
20 AWG  
(0.5 mm2)  
18 AWG  
(1.0 mm2)  
16 AWG  
(1.5 mm2)  
14 AWG  
(2.5 mm2)  
36  
79 ft  
(24 m)  
125 ft  
(38 m)  
199 ft  
(60 m)  
316 ft  
(96 m)  
NOTE: Input power for the dome is 24 VAC only. Power consumption  
is 36 VA per dome. Use a 24 VAC transformer with a minimum of  
36 VA per dome.  
C2494M (12/05)  
3
 
Install the back box by compressing the spring clips and pushing the  
back box through the hole. Tighten the screws until you hear a clicking  
noise.  
4
Suspended Ceiling Only: Install the ceiling tile with the back box.  
Attach a T-rail clip on each side of the ceiling tile to hold the ceiling tile  
secure during installation of the dome drive and lower dome.  
Connect the power wires to the circuit board inside the back box.  
Connect any alarm and auxiliary circuits. Turn on the power to the  
system. The green LED on the door indicates system power is on.  
ALARMS  
5
6
ALARM COM  
AUX1  
NOTE: Aux 1 – Maximum 2 A at low voltage (<40 V)  
AUX COM  
POWER  
Connect a 10/100/1000BaseT network Cat5e (or better) cable to the  
RJ-45 network connector located inside the back box. Check the LED  
indicators located inside the back box to check unit status, network  
status, and network activity.  
Unit Status LED  
Green  
Amber Unit is in configuration mode.  
Red Unit is in an error condition.  
Unit is functioning normally.  
Network Status LED  
Off  
Unit is not connected to the network.  
Amber Unit is connected to a 100BaseT network.  
Red  
Unit is connected to a 10BaseT network.  
Network Activity LED  
The LED flashes whenever the unit is sending or receiving network data.  
SW1-1 is set to the ON position.  
All other switches are set to the OFF position.  
No DIP switch settings are required for the system. Before installing the  
dome drive verify that switch SW1-1 (SW1, switch 1) is set to the ON  
position and all other switches are set to the OFF position.  
7
The switches set the dome drive for Pelco’s D protocol, address 1,  
2400 baud, and no termination.  
8
6 7  
4 5  
2 3  
1
1
6
7 8  
3
4
5
1
2
SW3  
ON  
SW2  
SW1  
on  
on  
4
C2494M (12/05)  
 
Install the dome drive. Line up the blue (A) and red (B) tabs with the blue  
(A) and red (B) labels. Push in the tabs. Insert one side and then the  
other side. Continue pushing on the ends of the tabs until both sides  
click into place.  
B
8
9
Install the lower dome. Snap the clip of the lower trim ring leash into the  
hole on the lip of the back box. Snap the trim ring into the plastic snap  
washers on the mounting screws.  
To operate or program your Spectra III EVS dome drive, refer to the  
following manuals:  
Information Required  
Where to Find Information  
Spectra’s programmable  
Spectra III Operation/  
features, commands, and menu Programming manual supplied  
structure  
How to control the dome drive  
and access preset 95 with the  
WS5050  
EnduraWS5000 Advanced  
System Software Operation  
manual supplied with the  
How to control the dome drive  
and access preset 95 with the  
VCD5000  
Endura VCD5000 Video Control  
Display Operation manual  
C2494M (12/05)  
5
 
Specifications  
SYSTEM  
Processor  
Operating System  
User Interface  
VIDEO ACTIVITY DETECTION  
PowerPC® 405EP  
Linux®  
Remote operation via WS5050 or  
VCD5000  
Zones  
3 plus background zone  
Zone Types  
Any shape, user-definable in 16 x 16 pixel  
blocks  
Sensitivity  
Adjustable  
ELECTRICAL  
Input Voltage  
Input Power  
GENERAL  
Construction  
Back Box  
Dome Drive  
Bubble  
Light Attenuation  
Smoked  
18-30 VAC; 24 VAC nominal  
36 VA nominal (without heaters)  
88 VA nominal (with heaters)  
1.25 A  
1
7
Aluminum  
Aluminum, thermo plastic  
Acrylic  
Fuse  
Auxiliary Outputs  
Alarm Inputs  
1/2 F-stop light loss  
Zero light loss  
Clear  
Chrome and Gold  
Cable Entry (Back Box)  
Weight (approximate)  
Back Box  
Dome Drive  
Lower Dome  
Environment  
2 F-stops light loss  
0.75-inch (1.91 cm) conduit fitting  
Unit  
2.8 lb (1.27 kg)  
2.4 lb (1.09 kg)  
0.2 lb (0.09 kg)  
Indoor  
32° to 122°F (0° to 50°C)  
VIDEO  
Video Standards  
Video Coding  
Video Streams  
NTSC/PAL/EIA/CCIR composite  
MPEG-4  
2, simultaneous  
Shipping  
4 lb (1.81 kg)  
4 lb (1.81 kg)  
1 lb (0.45 kg)  
Video Resolutions  
NTSC  
PAL  
4CIF  
2CIF  
CIF  
704 x 480  
704 x 240  
352 x 240  
176 x 120  
704 x 576  
704 x 288  
352 x 288  
176 x 144  
Operating Temperature  
Effective Projected Area (EPA) 92 square inches (without mount);  
QCIF  
138 square inches (with IWM Series  
mount)  
Video Inputs/Connectors  
Video Switch  
2, BNC, looping, 75¾, 1 Vp-p  
Hi-Z, 75¾  
IN-CEILING  
7.50  
(19.68)  
7.20  
(18.28)  
3.50  
(8.89)  
6.00  
(15.24)  
8.25  
(20.95)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.  
6
C2494M (12/05)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800)þ289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted  
pair transmission products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product when  
returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed  
dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair).  
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.  
The lamp and color wheel will be covered for a period of 90 days. The air filter is not  
covered under warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product lia-  
bility, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such  
Products. In no event will Pelco be liable for any special, incidental or consequential damages  
(including loss of use, loss of profit and claims of third parties) however caused, whether by  
the negligence of Pelco or otherwise.  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
Date  
Comments  
C2494M  
12/05  
Original version.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2005, Pelco. All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc.  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Australia Canada Finland France Italy Russia Singapore Spain Sweden The Netherlands United Arab Emirates United Kingdom United States  
|
|
|
|
|
|
|
|
|
|
|
|
 

Pelco Home Security System RK5000 3U User Manual
Pelco Switch CM8500 User Manual
Philips Electric Shaver 282XL User Manual
Philips TV VCR Combo 14PV325 User Manual
Pioneer Stereo Receiver VSX 518 User Manual
Polaroid Security Camera IP300 User Manual
Poulan Brush Cutter 530164830 User Manual
Poulan Trimmer QCT46 User Manual
Poulan Trimmer TE 450 LE User Manual
PYLE Audio Speaker PASW 15 User Manual