CC1400HZ16-* Series
DESCRIPTION
SPECIFICATIONS
General
Environmental
Operating
Temperature
Storage
Temperature
Humidity
The CC1400HZ16-* Series DSP Color CCD
Camera combines high resolution imaging
and a built-in lens in a compact package.
This DSP (Digital Signal Processing) camera
uses a 1/4-inch color CCD (charged coupled
device) interline transfer sensing element.
The built-in lens has a maximum zoom ratio
of 128X (16X optical and 8X digital).
Imaging Device
Color 1/4-inch interline
transfer CCD
NTSC
768 (H) x 508 (V)
2:1 interlace
32°-113°F (0°-45°C)
Signal System
Pixels
Scanning System
Sync System
12 VDC
32°-140°F (0°-60°C)
0%-80% relative
humidity
DSP
Color
CCD Camera
Internal
synchronization
External AC line lock
Physical
Construction
Finish
Dimensions
CC1400HZ16-2
24 VAC
Aluminum case
Neutral gray
The telephoto (zoom in), white balance, and
wide angle (zoom out) controls are push but-
tons located on the back of the camera.
When you press and hold the telephoto but-
ton, the camera reaches maximum optical
magnification (16X). If you continue to press
and hold the telephoto button, the camera
automatically goes into 8X digital zoom. Auto
focus is enabled during zoom lens setup. The
white balance control renders colors based
on the amount of white in the scene. Once
you set the white balance, the camera holds
the setting until you adjust the white balance
again.
Horizontal Resolution 470 TV lines
Signal-to-Noise Ratio >46 dB
Minimum Illumination 1.0 lux, F1.6, 30 IRE,
AGC on, 89.9%
C1960M-A
2.36 (H) x 2.27 (W) x
5.63 (L) inches
(5.99 x 5.77 x 14.30
cm)
2.36 (H) x 2.27 (W) x
4.42 (L) inches
(5.99 x 5.77 x 11.20
cm)
reflectance
SAFEGUARDS AND WARNINGS
Gain Control
Exposure
Automatic
Automatic
CC1400HZ16-4
Prior to installation and use of this product,
the following WARNINGS should be observed.
(1/60–1/10,000)
Push to set auto
3.9 to 63 mm
16X optical, 8X digital
(total 128X)
White Balance
Focal Length
Zoom Ratio
1. Installation and servicing should only be
done by qualified service and installation
personnel.
Weight
12 VDC
24 VAC
0.75 lb (0.34 kg)
0.95 lb (0.43 kg)
Minimum
Focus Distance
0.01m (wide angle),
1.20m (telephoto)
Auto focus
2. Installation shall be done in accordance
with all local and national electrical and
mechanical codes utilizing only approved
materials.
(Design and product specifications
subject to change without notice.)
Additional adjustments can be made by con-
necting the camera to a personal computer
through an RS-422 cable interface. For infor-
mation about adjusting the camera through
an RS-422 interface cable, please contact
the factory.
Focus Mode
Iris Control
Automatic
Camera Control
RS-422 cable
interfaced with PC
3. Use only installation methods and
materials capable of supporting four
times the maximum specified load.
Electrical
Power Requirements
CC1400HZ16-2
CC1400HZ16-4
Power Consumption
CC1400HZ16-2
MODELS
CC1400HZ16-2 NTSC format camera,
24 VAC, 50/60 Hz
12 VDC, 50/60 Hz
This symbol indicates that there
are important operating and main-
tenance instructions in the litera-
ture accompanying this unit.
24 VAC
6 watts maximum
(camera only)
®
CC1400HZ16-4 NTSC format camera,
12 VDC
3500 Pelco Way • Clovis, CA 93612-5699 • USA
In North America and Canada:
Tel (800) 289-9100 or FAX (800) 289-9150
CC1400HZ16-4
Video Output
4.7 watts maximum
(camera only)
Composite output,
75 ohms terminated
Please thoroughly familiarize yourself with
the information in this manual prior to instal-
lation and operation.
International Customers:
Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120
® Pelco and the Pelco logo
are registered trademarks of Pelco.
© Copyright 2004, Pelco. All rights reserved.
|