Pelco MP3 Player CM9700 SER 32 User Manual

I N S T A L L A T I O N / O P E R A T I O N  
CM9700-SER-32  
Port Expander  
C579M-A (5/05)  
 
Contents  
List of Illustrations  
C579M-A (5/05)  
3
 
Regulatory Notices  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may  
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in  
which case the user will be required to correct the interference at his own expense.  
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this  
equipment under Federal Communications Commission’s rules.  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.  
4
C579M-A (5/05)  
 
 
Installation  
The CM9700-SER-32 port expander assembly increases by 32 the number of available Sercom (serial communication) ports in a node-based  
CM9700-CC1 via the installation of an RP (rocket port) PCI expansion card. A maximum of 120 total ports can be achieved by using three  
2
2
4
RS-232/422 SWITCH (32)  
COMM INTERFACE FOR EACH  
CONNECTOR IS SET BY THIS  
SWITCH. UP IS RS-422;  
DOWN IS RS-232  
PCI EXPANSION CARD (1)  
(ROCKET PORT CARD)  
2
3
2
HOST CONNECTIONS  
CM9700-ADP-120  
ADAPTER BRACKET  
CONNECTING DATA CABLE (2)  
ONE SET OF CONNECTING DATA  
FOR USE WITH RP CARD CABLES IS PROVIDED. EACH  
IN PCI SLOT 1.  
CABLE IS THREE FEET LONG.  
ADAPTER DB25 TO RJ-45 (32)  
Figure 1. CM9700-SER-32 Assembly Detail  
4 SERCOM CARDS, 1 ROCKET PORT CARD (64 TOTAL PORTS)  
WARNINGS:  
Software version 9.03.007 or higher must be installed in the CC1 to enable port expansion ability. If running a previous version, contact Pelco  
for software upgrade kit options and availability.  
Failure to turn off the CC1 power could result in serious damage to the equipment.  
Electrostatic discharge (ESD) precautions must be observed when performing the procedures described in this manual. Always wear a  
gounding strap connected to an approved grounding source when working on or around exposed electronic components.  
1. Turn off all power to the CC1. Disconnect and label all attached cabling.  
a. Remove the top cover mounting screws.  
b. From the rear, tilt the top cover up at a slight angle, and then pull backwards away from the front edge to remove the cover from the  
CC1 chassis.  
NOTE: If the VGA card is present in PCI slot 2, remove the retaining screw and gently pull the card up. Reinstall the card into PCI slot 4 (follow  
steps c and d, applying them to the VGA card and PCI slot 4).  
c. Remove the retaining screw and slot cover for PCI slot 2. Slide the cover out.  
d. Install the RP card into PCI slot 2. Carefully align the gold-fingered edge connector of the RP card with the PCI slot. Gently but firmly  
press the RP card down until fully seated into the PCI slot. Reinstall the retaining screw to secure the RP card into place.  
C579M-A (5/05)  
5
 
     
e. Reinstall the top cover and secure with mounting screws.  
Figure 2. Removing the CC1 Top Cover  
RETAINING  
SCREW  
COVER  
ISA  
SLOTS  
PCI  
EXPANSION  
SLOTS  
Figure 3. CC1 Internal Layout  
a. Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit. The data cables are three feet in length.  
b. Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1. Connect the other (female)  
end to the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit.  
c. Connect the male end of the remaining data cable to the top DB26 connector of the RP card. Connect the other end to the DB25 host  
connector for the first grouping of 16 ports on the left side of the port expansion unit.  
d. If using RS-232 operation, set the switch located to the right of each port used on the port expansion unit to the “232” position.  
6
C579M-A (5/05)  
 
   
67  
59  
65  
57  
63  
55  
61  
53  
51  
43  
49  
41  
47  
39  
45  
37  
68  
60  
66  
58  
62  
54  
64  
52  
44  
50  
42  
48  
40  
46  
38  
B
T
RP 1  
56  
99  
97  
89  
95  
93  
85  
83  
75  
81  
73  
79  
71  
77  
69  
98  
90  
100  
96  
88  
94  
86  
84  
76  
82  
74  
80  
72  
78  
70  
B
RP 2  
T
91  
87  
92  
131  
132  
129  
127  
125  
113  
115  
111  
109  
130  
128  
126  
116  
114  
112  
110  
102  
B
T
RP 3  
123  
124  
121  
119  
117  
118  
107  
105  
103  
101  
122  
120  
108  
106  
104  
T = Top connector on rocket card  
B = Bottom connector on rocket card  
Figure 4. Rocket Card to Expansion Port Control Association  
4. Apply power to the CC1. After applying power, press the Delete key on the keyboard to enter into the BIOS menu settings, and then do the  
following:  
a. After “ENTER CURRENT PASSWORD” appears on the screen, type PELCON and then press the Enter key.  
b. Using the arrow key, scroll down to PCI PLUG AND PLAY SETUP, and then press Enter.  
c. Scroll down to PCI SLOT 2 IRQ PRIORITY. Change the setting to “15” by repeatedly pressing the Page Down key.  
d. Press the Esc key to return to the BIOS menu.  
5. Scroll down to SAVE SETTINGS AND EXIT and type Y  
6. Press Enter.  
7. Reboot machine by pressing Ctrl+Alt+Del.  
C579M-A (5/05)  
7
 
 
4 SERCOM CARDS, 2 ROCKET PORT CARDS, COM 2 UNAVAILABLE (96 TOTAL PORTS)  
WARNING:  
Software version 9.03.007 or higher must be installed in the CC1 to enable port expansion ability. If running a previous version, contact Pelco  
for software upgrade kit options and availability.  
Failure to turn off the CC1 power could result in serious damage to the equipment.  
Electrostatic discharge (ESD) precautions must be observed when performing the procedures described in this manual. Always wear a  
gounding strap connected to an approved grounding source when working on or around exposed electronic components.  
1. Turn off all power to the CC1. Disconnect and label all attached cabling.  
a. Remove the top cover mounting screws.  
b. From the rear, tilt the top cover up at a slight angle, and then pull backwards away from the front edge to remove the cover from the  
CC1 chassis.  
NOTE: This configuration mandates that the VGA card be installed in PCI slot 4. If present in any other PCI slot, remove the retaining screw and  
gently pull the card up. Reinstall the card into PCI slot 4 (follow steps c and d, applying them to the VGA card and PCI slot 4).  
c. Remove the retaining screw and slot cover for PCI slots 2 and 3. Slide both covers out.  
d. Install an RP card into PCI slot 2. Carefully align the gold-fingered edge connector of the RP card with the PCI slot. Gently but firmly  
press the RP card down until fully seated into the PCI slot. Reinstall the retaining screw to secure the RP card into place.  
e. Repeat step d for installing the second RP card into PCI slot 3.  
3. Reinstall the top cover and secure with mounting screws.  
NOTE: This procedure is for each individual port expansion assembly (one RP card and port expansion unit) and is to be duplicated for each RP  
card installed in the CM9700-CC1. Power should not be applied until all physical connections have been secured.  
a. Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit. The data cables are three feet in length.  
b. Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1. Connect the other (female)  
end to the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit.  
c. Connect the male end of the remaining data cable to the top DB26 connector of the RP card. Connect the other end to the DB25 host  
connector for the first grouping of 16 ports on the left side of the port expansion unit.  
d. If using RS-232 operation, set the switch located to the right of each port used on the port expansion unit to the “232” position.  
6. Apply power to the CC1. After applying power, press the Delete key on the keyboard to enter into the BIOS menu settings, and then do the  
following:  
a. After “ENTER CURRENT PASSWORD” appears on the screen, type PELCON and then press the Enter key.  
b. Using the arrow key, scroll down to PCI PLUG AND PLAY SETUP, and then press Enter.  
c. Scroll down to PCI SLOT 2 IRQ PRIORITY. Change the setting to “15” by repeatedly pressing the Page Down key.  
d. Scroll down to PCI SLOT 3 IRQ PRIORITY. Change the setting to “3” by repeatedly pressing Page Down.  
7. Press the Esc key to return to the BIOS menu.  
8
C579M-A (5/05)  
 
 
8. Scroll down to PERIPHERAL SETTINGS, press Enter, and then do the following:  
a. Scroll down to ONBOARD SERIAL PORT 2.  
b. Change the setting to DISABLED by pressing Page Down.  
c. Press Esc.  
d. Scroll down to SAVE SETTINGS AND EXIT and type Y  
e. Press Enter.  
9. Reboot machine by pressing Ctrl+Alt+Del.  
3 SERCOM CARDS, 2 ROCKET PORT CARDS, COM 2 AVAILABLE (88 TOTAL PORTS)  
WARNING:  
Software version 9.03.007 or higher must be installed in the CC1 to enable port expansion ability. If running a previous version, contact Pelco  
for software upgrade kit options and availability.  
Failure to turn off the CC1 power could result in serious damage to the equipment.  
Electrostatic discharge (ESD) precautions must be observed when performing the procedures described in this manual. Always wear a  
gounding strap connected to an approved grounding source when working on or around exposed electronic components.  
1. Turn off all power to the CC1. Disconnect and label all attached cabling.  
3. From the rear, tilt the top cover up at a slight angle, and then pull backwards away from the front edge to remove the cover from the CC1  
4. Install the RP cards into the CC1.  
ESD-safe container.  
C579M-A (5/05)  
9
 
 
Figure 5. Sercom Card Mounting Plate Removal  
NOTE: If the VGA card is present in PCI slot 2, remove the retaining screw and gently pull the card up. Reinstall the card into PCI slot 4 (follow  
steps d, e, and f, applying them to the VGA card and PCI slot 4).  
d. Remove the retaining screw and slot cover for PCI slot 2. Slide the cover out.  
e. Install an RP card into PCI slot 1. Carefully align the gold-fingered edge connector of the RP card with the PCI slot. Gently but firmly  
press the RP card down until fully seated into the PCI slot.  
f.  
Repeat step e for installing the second RP card into PCI slot 2. Reinstall the retaining screw to secure the RP card into place.  
VGA CARD  
1
2
3
4
RP CARDS  
SERCOM  
CARDS  
Figure 6. Sercom/PCI Card Configuration for 88 Ports, Com 2 Available  
5. Install the CM9700-ADP-120 adapter plate. Carefully align the plate with the front of the three Sercom cards and the RP card in PCI slot 1  
while pushing in toward the CC1 chassis. Secure with mounting plate screws removed earlier. Refer to Figure 7.  
10  
C579M-A (5/05)  
 
   
Figure 7. CM9700-ADP-120 Adapter Plate Installation  
6. Reinstall the top cover and secure with mounting screws.  
NOTE: This procedure is for each individual port expansion assembly (one RP card and port expansion unit) and is to be duplicated for each RP  
card installed in the CM9700-CC1. Power should not be applied until all physical connections have been secured.  
a. Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit. The data cables are three feet in length.  
b. Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1. Connect the other (female)  
end to the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit.  
c. Connect the male end of the remaining data cable to the top DB26 connector of the RP card. Connect the other end to the DB25 host  
connector for the first grouping of 16 ports on the left side of the port expansion unit.  
d. If using RS-232 operation, set the switch located to the right of each port used on the port expansion unit to the “232” position.  
9. Apply power to the CC1. After applying power, press the Delete key on the keyboard to enter into the BIOS menu settings, and then do the  
following:  
a. After “ENTER CURRENT PASSWORD” appears on the screen, type PELCON and then press the Enter key.  
b. Using the arrow key, scroll down to PCI PLUG AND PLAY SETUP, and then press Enter.  
c. Scroll down to PCI SLOT 1 IRQ PRIORITY. Change the setting to “5” by repeatedly pressing the Page Down key.  
d. Scroll down to PCI SLOT 2 IRQ PRIORITY. Change the setting to “15” by repeatedly pressing Page Down.  
10. Press the Esc key to return to the BIOS menu.  
11. Reboot machine by pressing Ctrl+Alt+Del.  
C579M-A (5/05)  
11  
 
 
3 SERCOM CARDS, 3 ROCKET PORT CARDS, COM 2 UNAVAILABLE (120 TOTAL PORTS)  
WARNING:  
Software version 9.03.007 or higher must be installed in the CC1 to enable port expansion ability. If running a previous version, contact Pelco  
for software upgrade kit options and availability.  
Failure to turn off the CC1 power could result in serious damage to the equipment.  
Electrostatic discharge (ESD) precautions must be observed when performing the procedures described in this manual. Always wear a  
gounding strap connected to an approved grounding source when working on or around exposed electronic components.  
1. Turn off all power to the CC1. Disconnect and label all attached cabling.  
3. From the rear, tilt the top cover up at a slight angle, and then pull backwards away from the front edge to remove the cover from the CC1  
4. Install the RP cards into the CC1.  
a. Remove the screws securing the Sercom card mounting plate (refer to Figure 5).  
NOTE: This configuration mandates that the VGA card be installed in PCI slot 4. If present in any other PCI expansion slot, remove the retaining  
screw and gently pull the card up. Reinstall the card into PCI slot 4 (follow steps d, e, and f, applying them to the VGA card and PCI slot 4).  
d. Remove the retaining screw and slot cover for PCI slot 2 and 3. Slide both covers out.  
e. Install an RP card into PCI slot 1. Carefully align the gold-fingered edge connector of the RP card with the PCI slot. Gently but firmly  
press RP card down until fully seated into the PCI slot.  
f.  
Repeat step e for installing the second and third RP cards into PCI slots 2 and 3. Reinstall the retaining screws to secure these RP  
cards into place.  
VGA CARD  
1
2
3
4
RP CARDS  
SERCOM  
CARDS  
Figure 8. Sercom/PCI Card Configuration for 120 Ports, Com 2 Unavailable  
5. Install the CM9700-ADP-120 adapter plate. Carefully align the plate with the front of the three Sercom cards and the RP card in PCI slot 1  
while pushing in toward the CC1 chassis. Secure with mounting plate screws removed earlier. Refer to Figure 7.  
6. Reinstall the top cover and secure with mounting screws.  
12  
C579M-A (5/05)  
 
   
NOTE: This procedure is for each individual port expansion assembly (one RP card and port expansion unit) and is to be duplicated for each RP  
card installed in the CM9700-CC1. Power should not be applied until all physical connections have been secured.  
a. Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit. The data cables are three feet in length.  
b. Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1. Connect the other (female)  
end to the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit.  
c. Connect the male end of the remaining data cable to the top DB26 connector of the RP card. Connect the other end to the DB25 host  
connector for the first grouping of 16 ports on the left side of the port expansion unit.  
d. If using RS-232 operation, set the switch located to the right of each port used on the port expansion unit to the “232” position.  
9. Apply power to the CC1. After applying power, press the Delete key on the keyboard to enter into the BIOS menu settings, and then do the  
following:  
a. After “ENTER CURRENT PASSWORD” appears on the screen, type PELCON and then press the Enter key.  
b. Using the arrow key, scroll down to PCI PLUG AND PLAY SETUP, and then press Enter.  
c. Scroll down to PCI SLOT 1 IRQ PRIORITY. Change the setting to “5” by repeatedly pressing the Page Down key.  
d. Scroll down to PCI SLOT 2 IRQ PRIORITY. Change the setting to “15” by repeatedly pressing Page Down.  
e. Scroll down to PCI SLOT 3 IRQ PRIORITY. Change the setting to “3” by repeatedly pressing Page Down.  
10. Press the Esc key to return to the BIOS menu.  
11. Scroll down to PERIPHERAL SETTINGS, press Enter, and then do the following:  
a. Scroll down to ONBOARD SERIAL PORT 2.  
b. Change the setting to DISABLED by pressing Page Down.  
c. Press Esc.  
d. Scroll down to SAVE SETTINGS AND EXIT and type Y  
e. Press Enter.  
12. Reboot machine by pressing Ctrl+Alt+Del.  
C579M-A (5/05)  
13  
 
14  
C579M-A (5/05)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelco’s liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
C579M  
C579M-A  
Date  
8/02  
5/05  
Comments  
Original version.  
Changed CM9760 reference to CM9700. Manual updated to include CM9700-ADP-120 adapter plate, and revised installation instructions.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2005, Pelco. All rights reserved.  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Pentax Digital Camera Optio T20 User Manual
Pentax Telescope R 315N User Manual
Philips Baby Accessories SCF683 27 User Manual
Philips Computer Drive FM16FD05B User Manual
Philips Portable Radio AE 1495 User Manual
Philips TV VCR Combo 21PV330 07 User Manual
Philips Universal Remote SBC RU631 87 User Manual
Pioneer CD Player PD D6MK2 K User Manual
Poulan Chainsaw 545001498 User Manual
PYLE Audio Music Pedal PPDLOD User Manual