Pelco Network Card C4680M A 8 11 User Manual

I N S T A L L A T I O N  
®
Endura UDI5000 Series  
Universal Device  
Interface  
For Third-Party Edge Devices  
C4680M-A (8/11)  
 
Contents  
C4680M-A (8/11)  
3
 
Important Notices  
REGULATORY NOTICE  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This  
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this  
equipment under Federal Communications Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
KOREAN CLASS B EMC  
이 기기는 가정 용 (B 급 ) 으로 전자파 적합 등록을 한 기기 로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든  
지역에서 사용할 수 있습니다  
C4680M-A (8/11)  
5
 
   
Description  
The Endura® UDI5000 Series universal device interface provides a flexible integration platform between third-party IP sources and the Endura IP  
video surveillance system.  
The UDI5000-CAM models can accommodate IP camera streaming for as many as 16 standard resolution cameras and several megapixel  
cameras from most manufacturers. Any combination and any mix of IP camera type and manufacturer is supported to reach a maximum bit rate,  
frame rate, and resolution. These cameras can be distributed throughout the network and then associated with a UDI5000 Series to translate  
network communication packets into a standard that is compatible with the Endura system. As more third-party sources are added to the system,  
they can be associated with additional UDI5000 Series units.  
When third-party IP cameras are associated with the universal device interface, live and recorded video are accessible in the Endura system, and  
all camera functions are available from any viewing station on the system.  
The UDI5000-MTRX provides users with a powerful means by which to leverage investments in legacy analog systems and integrations, while  
paving the way to leverage the benefits afforded by today’s IP and megapixel camera technologies. The UDI5000-MTRX has three operation  
modes to integrate ASCII interfaces into an Endura system, extend the operational life of analog matrix switchers by pulling digital video from  
standard resolution and megapixel IP devices, or provide the functionality and operator interface of the analog matrix without the cost and  
complexity of the matrix hardware.  
MODELS  
UDI5000-CAM  
Universal device interface for use with third-party cameras  
UDI5000-MTRX  
Universal device interface for use as an ASCII interface, matrix digital decoder (MDD), or V9700 virtual matrix  
controller  
COMPATIBLE PRODUCTS  
Endura System Components  
The UDI5000 Series is fully compatible with Endura 2.x or later components. The UDI5000-MTRX is compatible  
with existing CM9700 matrix systems. In V9700 mode, the system can include CM9700-ALM alarm interface  
units and CM9700-KBD keyboards.  
Third-Party Cameras  
The UDI5000-CAM is compatible with several camera vendors. For an updated list of supported cameras, go to  
Third-Party ASCII Systems  
The UDI5000-MTRX converts Pelco ASCII commands and Pelco P protocol commands into Endura messages.  
PARTS LIST  
The following parts are supplied with the device.  
Qty Description  
1
4
1
UDI5000 Series universal device interface  
Rubber mounting feet, attached  
Power cord (either 1 United States standard, European standard, United Kingdom standard, Australian standard, or Argentinian standard)  
NOTE: Units shipped to China do not include power cords.  
1
Documentation packet containing the following items:  
2 Installation manuals (1 English, 1 Chinese)  
1 Important Safety Instructions (multilingual)  
1 Resource disc with additional documentation and supporting software  
USER-SUPPLIED PARTS LIST  
A Phillips screwdriver (if mounting the unit into a rack) and Cat5e or better network cable are needed but not supplied.  
The UDI5000-MTRX is designed to support third-party components, some of which might require additional parts to operate properly. For  
example, you might need to purchase a serial to Ethernet converter or a video down converter (sometimes referred to as a DVI to BNC converter).  
Consult with your Pelco sales representative to determine if you need to purchase these or other parts to support your implementation.  
6
C4680M-A (8/11)  
 
         
Product Overview  
FRONT AND REAR PANELS  
Figure 1 illustrates the front panel with and without the face plate, and Figure 2 illustrates the rear panel of the UDI5000 Series.  
UDI50000 Series  
Figure 1. UDI5000 Series Front Panel With and Without a Face Plate  
Pelco Badge and Power Indicator  
Face Plate Lock  
Network Activity Indicator  
Unit Status Indicator  
USB 2.0 Port  
Power Button  
Figure 2. UDI5000 Series Rear Panel  
Power Connector with Locking Mechanism  
Ethernet Network RJ-45 Connector  
(Not used)  
DB-9 Connector (RS-232)  
C4680M-A (8/11)  
7
 
       
Before You Begin  
Endura is a network system that requires a continuous amount of bandwidth to transmit live video; therefore, always include your network  
administrator when planning and installing Endura components.  
You will also need the following items:  
Pelco-approved Endura certification if you are installing an SM5000 system manager or NSM5200 network storage manager.  
Access to an Endura network  
that is an active, gigabit Ethernet network that supports the full Internet Protocol suite,  
that is configured with at least one SM5000 system manager  
PRODUCT SERIAL NUMBER LABEL PLACEMENT  
The product serial number label helps identify your universal device interface and its factory configuration settings in the event that the unit  
requires service.  
A label citing your product’s serial number is attached to the bottom panel of the universal device interface. Because rack mounting or other  
installation options may obscure the factory-applied label, two additional labels are provided. Attach one label to your product documentation or  
another product location that will not be obscured by installation. The second label is a spare.  
To use the serial number label, complete the following steps:  
1. On the bottom panel of the universal device interface, locate the two small labels, attached with a yellow sticker that reads “Extra serial  
number labels: remove prior to installation.”  
2. Remove the yellow sticker and the labels.  
3. Peel away the backing from one label and attach it to this manual, other product documentation, or an unobscured product location.  
Model  
MODEL  
03267-39-0020  
SN  
FREQ  
Sample Text  
AMPS  
Sample Text  
VOLTS  
Sample Text  
REV  
Sample Text  
MFG BY PELCO, CLOVIS, CA MADE IN USA  
Figure 3. Product Serial Number Label  
8
C4680M-A (8/11)  
 
     
Installation  
MOUNTING  
Use one of the following installation methods for the universal device interface (detailed instructions are provided in the following sections):  
Desktop installation: The UDI5000 Series is equipped with rubber feet for placement on a flat surface, such as a shelf or desktop.  
Rack mount installation: Turn the unit upside down and remove the four rubber feet from the unit. The feet are attached with screws.  
Store the screws and feet for future use. Install the unit in the optional RK-UDI5000 rack mount kit.  
DESKTOP INSTALLATION  
When placing the universal device interface on a flat surface, such as a desktop, be sure that you position the unit to allow for cable and power  
cord clearance at the rear panel.  
WARNING: Do not place the universal device interface on its side; the unit could fall over and cause equipment damage or personal injury.  
Figure 4. UDI5000 Series Desktop Placement  
RACK MOUNT INSTALLATION  
You can mount the UDI5000 Series in the optional RK-UDI5000 rack mount kit along with a second unit. The rack mount kit is designed to support  
two UDI5000 Series units in a side-by-side installation. For installing a single unit, the rack mount kit contains support brackets that can be  
attached to the UDI5000 Series before installing it in a rack. The UDI5000 Series connects directly to a power brick that rests in a shelf at the  
back of the mounting kit. Clearance for power cords is provided for up to two units in the rack.  
Refer to the rack mount installation manual for instructions.  
HARDWARE CONNECTIONS  
NETWORK CONNECTION  
Consult your network administrator before installing the universal device interface to avoid possible network conflicts.  
Use the network port on the rear panel and a Cat5e (or better) cable with RJ-45 connectors to connect the universal device interface to your  
system network.  
RJ-45  
Figure 5. Network Connections  
C4680M-A (8/11)  
9
 
               
POWER CONNECTION  
To connect power, complete the following steps:  
1. Connect a power supply to the unit.  
2. Connect power to the power supply.  
3. Press the power button on the front panel. If necessary, remove the face plate to access the power button. The Pelco badge (blue) on the  
front panel should glow.  
Figure 6. Power Connections  
10  
C4680M-A (8/11)  
 
   
Software Configuration  
SOFTWARE UPDATES  
The UDI5000 Series uses the same procedure to update its software as any other device on the Endura system. Refer to the WS5200 Advanced  
System Management Software Configuration manual for instructions on updating software.  
SYSTEM SETTING CONFIGURATION FOR THE UDI5000 SERIES  
After the UDI5000 Series is connected to the Endura network and the power is turned on, the device is discovered automatically on the network.  
A dynamic IP address is assigned to the UDI5000 Series through the network Dynamic Host Configuration Protocol (DHCP) server. Use the Endura  
Utilities or the WS5200 advanced system management software to verify that the UDI5000 Series is available on the system. System settings for  
the UDI5000 Series are configured through the Web application that is provided within the unit. This application is accessed through a  
Microsoft® Internet Explorer® Web browser window by entering the IP address assigned to the unit. Refer to the configuration manual that is  
available on the resource disc for information on configuring the units.  
C4680M-A (8/11)  
11  
 
     
Troubleshooting  
LED indicators on the front panel of the UDI5000 Series allow you to monitor data activity and operating power. Table A provides troubleshooting  
information relating to the front panel indicators.  
If the following instructions fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA or Canada) or  
+1-559-292-1981 (international) for assistance.  
Note the following information before calling Pelco:  
Unit serial number: Located on the product label.  
Unit firmware version: Located on the System page in the UDI5000 Series system configuration software.  
NOTE: Do not try to repair the unit yourself. Opening it immediately voids any warranty. Leave maintenance and repairs to qualified technical  
personnel. Exchange the defective unit and return it for repair.  
Table A. Troubleshooting the UDI5000 Series  
Problem  
Indication  
Possible Causes  
Suggested Remedy  
Power LED (Pelco badge) Power is not being supplied to Power connection is faulty  
Check power connection; if the UDI5000  
Series is rack mounted, reseat the unit or  
the power supply as necessary  
is not lit  
the UDI5000 Series  
Power supply has failed  
Network cabling is faulty  
Replace power supply  
Network activity and  
status LED is not lit  
No network connection is  
available  
Ensure the cabling is tested for Cat5e or  
Cat6 connectivity  
Unit status indicator LED Internal hardware or software Log on to the configuration  
Check all camera connections, repair the  
camera associations; return to the factory  
for service  
is red  
failure  
software and check the camera  
connections; check the fans  
Unit status indicator LED Operating temperature is  
is amber approaching a threshold  
Improper installation or ambient Check the installation area for proper  
temperature has risen to  
dangerous level  
cooling and ventilation; reinstall the  
UDI5000 Series in an area with proper  
ventilation  
Unit status indicator LED UDI5000 Series is operating  
is green normally  
N/A  
N/A  
12  
C4680M-A (8/11)  
 
   
Specifications  
MODEL  
UDI5000-CAM  
Universal device interface for third-party cameras  
UDI5000-MTRX  
Universal device interface for CM9700 Series Matrix, V9700 virtual matrix, or ASCII systems  
GENERAL  
Construction  
Sheet metal  
Finish  
Gray metallic with black end caps, black matte finish  
Linux®  
Operating System  
Dimensions  
31.3 x 21.6 x 4.3 cm (12.32" D x 8.8" W x 1.70" H )  
Mounting  
Desktop  
Rack  
Rubber feet (factory-installed)  
Optional mounting accessories required  
Unit Weight  
3.0 kg (6.6 lb)  
FRONT PANEL INDICATORS/FUNCTIONS  
Power  
Blue  
Network Activity  
Unit Status  
Red, amber, green  
Red, amber, green  
REAR PANEL INDICATORS/FUNCTIONS  
Serial Port  
RS-232 DB-9 connector  
Network Port  
1 Gigabit Ethernet RJ-45 (10/100/1000Base-T)  
Other Ports (not used)  
2 USB 2.0 ports, 1 parallel port, 1 S-Video port, audio input/output  
POWER  
Power Input  
12 VDC  
Power Consumption  
60 W, 5 A, 205 BTU/H  
ENVIRONMENTAL  
Operating Temperature  
0° to 50°C (32° to 122°F)  
Storage Temperature  
Operating Humidity  
–40° to 65°C (–40° to 149°F)  
20% to 80%, noncondensing  
COMPATIBLE PRODUCTS  
Endura System Components  
The UDI5000 Series is compatible with Endura 2.x or later components.  
Third-party cameras  
The UDI5000 Series is compatible with several camera vendors. For an updated list of supported cameras,  
go to www.pelco.com.  
OPTIONAL ACCESSORIES  
RK-UDI5000  
Rack mounting hardware for two UDI5000 Series units  
STANDARDS/ORGANIZATIONS  
Pelco is a member of the MPEG-4 Industry Forum  
Pelco is a member of the Universal Plug and Play (UPnP) Forum  
Pelco is a member of the Universal Serial Bus (USB) Implementers Forum  
Pelco is a contributor to the International Standards for Organization/Electrotechnical Commission (ISO/IEC) Joint Technical Committee 1  
(JTC1), “Information Technology,” Subcommittee 29, Working Group 11  
Compliance, ISO/IEC 14496 standard (also known as MPEG-4)  
Compliant with International Telecommunication Union (ITU) Recommendation G.711, “Pulse Code Modulation (PCM) of Voice Frequencies”  
C4680M-A (8/11)  
13  
 
 
14  
C4680M-A (8/11)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment.  
• Six months:  
All pan and tilts, scanners, or preset lenses used in continuous motion  
applications (preset scan, tour, and auto scan modes)  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to a Pelco designated location. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Exceptions to this warranty are as noted below:  
• Five years:  
Fiber optic products  
Unshielded Twisted Pair (UTP) transmission products  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelcos liability  
for any claim, whether based on breach of contract, negligence, infringement of  
any rights of any party or product liability, relating to the Products shall not exceed  
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be  
liable for any special, incidental, or consequential damages (including loss of use,  
loss of profit, and claims of third parties) however caused, whether by the  
negligence of Pelco or otherwise.  
• Three years:  
Fixed network cameras and network dome cameras with Sarix® technology  
Sarix thermal imaging products (TI and ESTI Series)  
Fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, and  
IP3701H Series)  
EH1500 Series enclosures  
Spectra® IV products (including Spectra IV IP)  
Spectra HD dome products  
The above warranty provides the Dealer with specific legal rights. The Dealer may  
also have additional rights, which are subject to variation from state to state.  
Camclosure® Series (IS, ICS, IP) integrated camera systems  
DX Series video recorders (except DX9000 Series which is covered for a  
period of one year), DVR5100 Series digital video recorders, Digital Sentry®  
Series hardware products, DVX Series digital video recorders, and NVR300  
Series network video recorders  
Endura® Series distributed network-based video products  
Genex® Series products (multiplexers, server, and keyboard)  
PMCL200/300/400 Series LCD monitors  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the  
following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number  
3. Details of the defect or problem  
PMCL5xxF Series and PMCL5xxNB Series LCD monitors  
If there is a dispute regarding the warranty of a product that does not fall under  
the warranty conditions stated above, please include a written explanation with  
the product when returned.  
• Two years:  
Standard varifocal, fixed focal, and motorized zoom lenses  
DF5/DF8 Series fixed dome products  
Method of return shipment shall be the same or equal to the method by which the  
item was received by Pelco.  
Legacy® Series integrated positioning systems  
Spectra III, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, ExSite IP, and  
PS20 scanners, including when used in continuous motion applications  
RETURNS  
Esprit Ti and TI2500 Series thermal imaging products  
Esprit and WW5700 Series window wiper (excluding wiper blades)  
CM6700/CM6800/CM9700 Series matrix  
Digital Light Processing (DLP®) displays (except lamp and color wheel). The  
lamp and color wheel will be covered for a period of 90 days. The air filter is  
not covered under warranty.  
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100  
or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair) and designated return location.  
All merchandise returned for credit may be subject to a 20 percent restocking and  
refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned  
CA or RA number and freight should be prepaid.  
Revised 5-6-11  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
C4680M  
C4680M-A  
Date  
1/11  
8/11  
Comments  
Original version.  
Added feature descriptions for the V9700 mode and updated some illustrations.  
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates.  
All other product names and services are the property of their respective companies.  
© Copyright 2011, Pelco, Inc.  
All rights reserved.  
Product specifications and availability are subject to change without notice.  
 
Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States  
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150  
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120  
 

Peavey Stereo Equalizer Q431FX User Manual
Pelco Car Video System C2931M97 05 User Manual
Pelco Tablet C1421M B 8 98 User Manual
Philips Headphones SHH1710 User Manual
Philips Radio AE5250 User Manual
Philips TV DVD Combo 37MD359B User Manual
Pioneer DVD Player DV 373 K User Manual
Pioneer Speaker Active Reference Speakers for DJ Producer User Manual
Planar Model Vehicle sd2220w User Manual
Praktica Digital Camera D00387 User Manual