Peripheral Electronics Network Card iPod2car User Manual

Instruction Manual  
PROFESS
IO
NAL IN
ST
ALLATION  
ST
RO
NG
L
Y
A
D
VI
SED  
IMPORTANT NOTE  
iPod Firmware MUST be updated BEFORE any other step is taken.  
Otherwise, the iPod will not operate properly. See page 1 for further details.  
Peripheral Electronics®,  
a division of AAMP of America™  
13160 56th Court Clearwater, Florida 33760  
866-788-4237 in the US or 727-572-9255 ext.262 for international calls  
©2005 AAMP™ of Florida, Inc.  
rm02.21.05  
 
Chapter 1- Getting Started  
1.1 Introduction  
Thank you for purchasing Peripheral Electronics’® iPod2car interface. The  
iPod2car is designed to provide endless hours of listening pleasure through most  
vehicles’ factory radios. To ensure that your iPod performs correctly in your car or  
truck, we recommend that you read this entire manual before attempting installa-  
tion of the iPod2car interface  
The iPod2car interface will allow you to connect your iPod to a factory radio that  
has the ability to control a CD changer. The iPod2car is designed to be used with  
Generation 3, 4, Mini and Photo iPods.  
1.2 Precautions
(Important, Please Read)  
UPDATING iPod FIRMWARE  
For proper operation of the iPod2car, your iPod must be updated with the most  
recent version of Firmware from Apple. This is done on your computer. To Update  
directions on the website to complete the download. There is no charge for this  
update.  
PREVENTING DAMAGE TO YOUR VEHICLE OR iPod.  
To eliminate the risk of an electrical short, we recommend disconnecting the car  
battery in most vehicles, except in the following situations:  
Vehicles equipped with on-board navigation should not have the car’s battery  
disconnected. Doing so may cause loss of memory settings. These settings  
would then have to be reprogrammed by an authorized car dealer for a fee to  
be paid by the vehicle’s owner. For these vehicles, we recommend extreme  
caution when handling exposed 12V power or ground wires/connectors.  
Vehicles that incorporate a security-code protecting the radio. If the car’s battery  
or the radio’s power plugs are disconnected, the radio will not operate without  
re-entering the security-code. If you have access to the security-code, feel  
comfortable disconnecting the battery and the radio’s power connectors. Other  
wise, do not disconnect the battery and exercise extreme caution while handling  
exposed 12V power or ground wires/connectors.  
PROPER MOUNTING LOCATION  
Securely install the interface in a location free from; heat, humidity, moving parts or  
direct sunlight. Beware of hot-air flow from your vehicle’s climate control system.  
We recommend securing the interface to a suitable location, free of sharp metal  
edges, using; double sided tape, Velcro or wire ties.  
1
 
Docking cable  
Vehicle specific harness  
iPod2car interface  
1.3 Configuration and Harness Selection  
This section will instruct you on how to properly identify and/or confirm the proper in-  
terface dip-switch configuration and vehicle specific harness selection. On the follow-  
ing pages you will find our vehicle application guide. This guide will inform you of the  
proper dip-switch configuration and vehicle specific harness for your particular vehicle.  
Depending on the type of iPod2car kit you purchased, it might include a bundle of  
different vehicle harnesses or none at all. If the kit contains many harnesses, only one  
will be needed for your specific vehicle. If the kit came without any vehicle harness,  
your authorized Peripheral® dealer will have the harness for you to purchase separately.  
Before consulting the application guide please take a moment to review our IMPOR-  
TANT COMPATIBILITY NOTES below. These notes will inform you of any issues or  
circumstances that can affect the compatibility of our product with your factory audio  
system and accessories. Some situations result in the loss of use of some factory  
audio players. Please read and understand these notes before proceeding to the ap-  
plication guide.  
1.4 IMPORTANT Compatibility Notes!  
1.4.1 ALL 
VEHICLES-  
If your vehicle is equipped with a factory CD changer, you must disconnect it in order to  
be able to install the interface. You will lose the use of the factory CD changer to gain  
use of your iPod.  
1.4.2 ACURA-  
Not compatible with vehicles equipped with a factory Navigation system.  
1.4.3 CHEVROLET-  
The iPod2car interface is currently not compatible with any factory external audio  
source such as: XM tuner, Any CD player or Cd changer, or Cassette player. These  
devices must be disconnected during the installation and will longer function. You will  
lose the use of these devices to gain use of your iPod.  
1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible with  
the iPod2car interface because they do not have CD changer control functions.  
1.4.4 CHRYSLER-  
To determine if your vehicles radio has CD changer control functions, and will work with  
the iPod2car interface, check preset button #”1” for the “Disc ^” symbol.  
1999 Chrysler vehicles have one of two different style radios. These two radios use  
different harnesses. The shape of the radio face will determine which harness you will  
use. If your radio face is SQUARE, you will use the harness part# PXHCH1. If your  
radio face is OVAL (rounded corners), you will use the harness part# PXHCH2.  
2
 
1.4.5 DODGE- See Chrysler 1.4.4  
1.4.6 EAGLE See Chrysler 1.4.4  
1.4.7 FORD-  
The iPod2car is not compatible with factory radios with built-in 6-disc CD changers.  
1.4.8 GMC- See Chevrolet 1.4.3  
1.4.9 HONDA-  
Starting in 2003 Honda introduced a new series of radios that use different software that  
is currently incompatible with the iPod2car. In 2005 all Honda radios use this software-  
making them incompatible.  
1.4.10 HUMMER- See Chevrolet 1.4.3  
1.4.11 JEEP- See Chrysler 1.4.4  
1.4.12 LINCOLN-  
The iPod2car is not compatible with factory radios with built-in 6-disc CD changers.  
1.4.13 MERCURY-  
The iPod2car is not compatible with factory radios with built-in 6-disc CD changers.  
1.4.14 OLDSMOBILE-  
The iPod2car is not compatible with factory radios with built-in 6-disc CD changers.  
1.4.15 PLYMOUTH- See Chrysler 1.4.4  
1.4.16 PONTIAC-  
The iPod2car is not compatible with factory radios with built-in 6-disc CD changers.  
1.4.17 TOYOTA-  
2003-2005 Toyota vehicles have radios that appear to be the same but use different  
harnesses. Unfortunately, because the radios have the same outward appearance, the  
only way to determine which harness to use is to remove the radio and visually confirm  
the connector on the back of the radio. If the harness part# PXHTY1 harness does  
not fit into the connector on your radio, you will also need the harness part# PXHTY2  
adapter harness that will adapt the PXHTY1 to fit the newer style radio connectors.  
1.4.18 VOLKSWAGEN-  
When possible, we recommend using the PXHVW2 harness and install the iPod2car  
behind the radio. This will avoid the possibility of inherent noise problems with the  
factory VW CD changer cable that is found in some vehicles.  
Double DIN (4” Tall) VW radios have a new connector that is not yet available. In  
these cases, you must use the PXHVW1 and install the iPod2car interface in the  
factory CD changer location. If you encounter the aforementioned inherent noise  
technical bulletin that will instruct you on how to eliminate the noise.  
3
 
1.5
APPLICATION GUIDE  
ASIAN IMPORT  
Manufacturer  
/ Fabricant  
Year  
/ Année  
Interface  
Location  
Model / Modèle  
Harness  
Configuration  
NOTE: NOT Compatible with Vehicles Equipped with Navigation  
Nota : Non Compatible Avec Les Véhicules Dotés De La Fonction Navigation  
Acura  
CL  
Integra  
Integra  
Legend  
RL  
RSX  
TL  
Vigor  
1996-2002  
1992-2001  
1992-2001  
1992-1995  
1996-2002  
2002  
PXHCH2  
PXHCH2  
PXHCH2  
PXHCH2  
PXHCH2  
PXHCH2  
PXHHD1  
PXHCH2  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
1999-2002  
1992-1994  
NOTE: NOT Compatible with Vehicles Equipped with Built-in 6 Disc Changer  
Honda  
Nota : Non Compatible Avec Les Véhicules Dotés D’Un Changeur De 6 CD Intégré  
Accord  
Accord  
Civic  
Civic  
CRV  
1992-1997  
1998-2002  
1992-1997  
1998-2004  
1997  
1997-2004  
1993-1997  
2002  
2001-2004  
1995-1997  
1998-2004  
1998-2002  
1992-1997  
1998-2001  
2000-2003  
PXHCH2  
PXHHD1  
PXHCH2  
PXHHD1  
PXHCH2  
PXHHD1  
PXHCH2  
PXHHD1  
PXHHD1  
PXHCH2  
PXHHD1  
PXHHD1  
PXHCH2  
PXHHD1  
PXHHD1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 1  
Config. # 9  
Config. # 1  
Config. # 1  
Config. # 1  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
CRV  
Del Sol  
Element  
Insight  
Odyssey  
Odyssey  
Passport  
Prelude  
Prelude  
S2000  
Amigo  
1998-2000  
PXHTY1  
Config. # 9  
Radio  
Isuzu  
Rodeo  
Trooper  
1998-2002  
1998-2002  
PXHTY1  
PXHTY1  
Config. # 9  
Config. # 9  
Radio  
Radio  
B-series Truck  
1997  
PHXFD2  
Config. # 4  
Radio  
Mazda  
B-series Truck  
Tribute  
1998-2001  
2001-2002  
PXHFD3  
PXHFD3  
Config. # 4  
Config. # 4  
Radio  
Radio  
Manufacturer  
/ Fabricant  
Year  
/ Année  
Interface  
Location  
Model / Modèle  
Harness  
Configuration  
Quest  
tC  
1999-2002  
2003-2005  
PXHFD3  
PXHTY3  
Config. # 4  
Config. # 9  
Radio  
Radio  
Nissan  
Scion  
xA  
xB  
2003-2005  
2003-2005  
PXHTY3  
PXHTY3  
Config. # 9  
Config. # 9  
Radio  
Radio  
NOTE: Matrix NOT Compatible when Equipped with Built-in 6 Disc Changer  
Toyota  
Nota : Non Compatible Avec Les Véhicules Dotés D’Un Changeur De 6 CD Intégré  
4-Runner  
Avalon  
Camry  
Solara  
Celica  
1998-2005  
1998-2005  
1998-2005  
1999-2003  
1998-2005  
1998-2005  
2000-2005  
2001-2004  
1998-2005  
2003-2004  
2005  
2000-2005  
2001-2005  
1998-2005  
2001-2005  
1998-2005  
2004-2005  
1998  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHGM3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
PXHTY3  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 7  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Config. # 9  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Corolla  
Echo  
Highlander  
Landcruiser  
Matrix  
Matrix  
MR2  
Prius  
RAV4  
Sequioa  
Sienna  
Solara  
Supra  
T100  
Tacoma  
Tercel  
1998  
1998-2005  
1998  
Tundra  
2000-2005  
4
 
1.5
APPLICATION GUIDE  
FORD  
Manufacturer  
/ Fabricant  
Year  
/ Année  
Interface  
Location  
Harness  
Configuration  
Model / Modèle  
NOTE: Not Compatible with In-dash 6 Disc CD Changer  
Ford  
Nota : Non Compatible Avec Un Changeur De 6 CD Intégré Au Tableau De Bord  
PXHFD2  
PXHFD3  
PXHFD3  
PXHFD2  
PXHFD3  
PXHFD2  
PXHFD2  
PXHFD3  
PXHFD2  
PXHFD3  
PXHFD3  
PXHFD2  
PXHFD3  
PXHFD4  
PXHFD3  
PXHFD2  
PXHFD3  
PXHFD3  
PXHFD1  
PXHFD3  
PXHFD3  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 5  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Crown Victoria  
Crown Victoria  
Escape  
Econoline  
Econoline  
Escort  
Expedition  
Expedition  
Explorer  
Explorer  
Freestar  
F-series Pick Up  
F-series Pick Up  
Focus  
1995-1997  
1998-2003  
2001-2004  
1997  
1998-2004  
1997-2003  
1997  
1998-2003  
1995-1997  
1998-2004  
2004-2005  
1995-1997  
1998-2003  
2000-2003  
2001-2003  
1995-1997  
1998-2004  
2000-2004  
1996-2005  
2000-2004  
1999-2003  
Year  
Mustang  
Ranger  
Ranger  
Sport Trac  
Taurus  
Thunderbird  
Windstar  
Manufacturer  
/ Fabricant  
Interface  
Location  
Harness  
Configuration  
Model / Modèle  
/ Année  
NOTE: Not Compatible with In-dash 6 Disc CD Changer  
Lincoln  
Nota : Non Compatible Avec Un Changeur De 6 CD Intégré Au Tableau De Bord  
PXHFD3  
PXHFD2  
PXHFD3  
PXHFD3  
PXHFD2  
PXHFD2  
PXHFD3  
PXHFD2  
PXHFD3  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Avaitor  
Continental  
Continental  
LS  
Mark VIII  
Navigator  
Navigator  
Town Car  
Town Car  
2002-2003  
1995-1997  
1998-2004  
2000-2003  
1995-1998  
1997-1998  
1999-2003  
1995-1997  
1998-2003  
NOTE: Not Compatible with In-dash 6 Disc CD Changer  
Nota : Non Compatible Avec Un Changeur De 6 CD Intégré Au Tableau De Bord  
Mercury  
PXHFD4  
PXHFD2  
PXHFD3  
PXHFD2  
PXHFD3  
PXHFD1  
PXHFD1  
PXHFD3  
Config. # 5  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Config. # 4  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Cougar  
Grand Marquis  
Grand Marquis  
Mountaineer  
Mountaineer  
Sable  
1999-2003  
1995-1997  
1998-2003  
1995-1997  
1998-2004  
1996-2005  
1995-2004  
1999-2002  
Tracer  
Villager  
5
 
1.5
APPLICATION GUIDE  
CHRYSLER  
Manufacturer  
/ Fabricant  
Interface  
Location  
Year / Année  
Harness Configuration  
Model / Modèle  
NOTE: ONLY Works in Vehicles with Radio with “DISC ^ ” Printed on Preset Button # 1  
Chrysler  
Nota : Ne Fonctionne Que Dans Les Véhicules Où « Disc ^ » Est Imprimé Sur Le Bouton De Préréglage No 1 De La Radio  
PXHCH1  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH1  
PXHCH2  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
Config. # 1  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 1  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
300M  
300M  
Cirrus  
1999-2001  
2002-2003  
1995-1999  
1999-2000  
1995-1999  
1999-2001  
2002-2004  
1995  
1995-1999  
1999-2001  
1995-1997  
2001  
Cirrus  
Concorde  
Concorde  
Concorde  
Le Baron  
LHS  
LHS  
New Yorker  
Prowler  
Prowler  
2002  
2001  
PT Cruiser  
PT Cruiser  
Sebring  
Sebring  
Sebring  
Town & Country  
Town & Country  
Town & Country  
2002-2005  
1995-1999  
1999-2001  
2002-2004  
1995-1999  
1999-2001  
2002-2004  
NOTE: ONLY Works in Vehicles with Radio with “DISC ^ ” Printed on Preset Button # 1  
Dodge  
Nota : Ne Fonctionne Que Dans Les Véhicules Où « Disc ^ » Est Imprimé Sur Le Bouton De Préréglage No 1 De La Radio  
PXHCH1  
PXHCH2  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH3  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
Config. # 1  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Avenger  
Avenger  
Caravan  
Caravan  
Caravan  
Dakota  
Dakota  
Dakota  
Durango  
Durango  
Durango  
Intrepid  
1995-1999  
1999-2000  
1995-1999  
1999-2001  
2002-2004  
1995-1999  
1999-2001  
2002-2005  
1998-1999  
1999-2001  
2002-2004  
1995-1999  
1999-2001  
2002-2004  
1995-1999  
1999-2001  
2002-2004  
1995-1999  
1999-2001  
2002-2004  
1995  
Intrepid  
Intrepid  
Neon  
Neon  
Neon  
Ram Pickup  
Ram Pickup  
Ram Pickup  
Spirit  
Sprinter  
Stratus  
Van (Fullsize)  
Van (Fullsize)  
Van (Fullsize)  
2004  
2002-2004  
1995-2003  
1995-2003  
1995-2003  
6
 
1.5
APPLICATION GUIDE  
CHRYSLER CON
T
.  
Manufacturer  
/ Fabricant  
Interface  
Location  
Year / Année  
Harness Configuration  
Model / Modèle  
NOTE: ONLY Works in Vehicles with Radio with “DISC ^ ” Printed on Preset Button # 1  
Eagle  
Nota : Ne Fonctionne Que Dans Les Véhicules Où « Disc ^ » Est Imprimé Sur Le Bouton De Préréglage No 1 De La Radio  
PXHCH1  
PXHCH1  
Config. # 1  
Config. # 1  
Radio  
Radio  
Summit  
Vision  
1995-1996  
1995-1997  
NOTE: ONLY Works in Vehicles with Radio with “DISC ^ ” Printed on Preset Button # 1  
Nota : Ne Fonctionne Que Dans Les Véhicules Où « Disc ^ » Est Imprimé Sur Le Bouton De Préréglage No 1 De La Radio  
Jeep  
PXHCH1  
PXHCH2  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH3  
Config. # 1  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Cherokee  
Cherokee  
Grand Cherokee  
Grand Cherokee  
Grand Cherokee  
Liberty  
Wrangler  
Wrangler  
Wrangler  
1995-1999  
1999-2001  
1995-1999  
1999-2001  
2002-2004  
2002-2004  
1995-1999  
1999-2001  
2002-2004  
NOTE: ONLY Works in Vehicles with Radio with “DISC ^ ” Printed on Preset Button # 1  
Nota : Ne Fonctionne Que Dans Les Véhicules Où « Disc ^ » Est Imprimé Sur Le Bouton De Préréglage No 1 De La Radio  
Plymouth  
PXHCH1  
PXHCH1  
PXHCH2  
PXHCH1  
PXHCH2  
PXHCH3  
PXHCH1  
PXHCH2  
PXHCH1  
PXHCH2  
Config. # 1  
Config. # 1  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 3  
Config. # 1  
Config. # 3  
Config. # 1  
Config. # 3  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Acclaim  
Breeze  
Breeze  
Neon  
Neon  
Neon  
Prowler  
Prowler  
Voyager  
Voyager  
1995  
1996-1999  
1999-2000  
1995-1999  
1999-2001  
2002-2004  
1997-1999  
1999-2000  
1995-1999  
1999-2000  
EURO-IMPORT  
Manufacturer  
Fabricant  
/
Year  
Interface  
Location  
Model / Modèle  
Harness Configuration  
/ Année  
PXHAD1  
Config. # 2  
Trunk  
A4  
1998-2004  
Audi  
PXHAD1  
PXHAD1  
PXHAD1  
PXHAD1  
PXHAD1  
PXHAD1  
PXHAD1  
PXHAD1  
PXHAD1  
PXHAD1  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
A6  
A8  
A8L  
All-Road  
Cabriolet  
RS6  
S4  
S6  
S8  
TT  
1998-2002  
1998-2002  
2004-2004  
2001-2004  
1998  
2000-2003  
2000-2004  
2002-2003  
2001-2002  
2000-2004  
PXHFD4  
PXHVW2  
Config. # 4  
Config. # 2  
Radio  
Radio  
S-Type  
2000-2002  
Jaguar  
Volkswagen  
Beetle  
1998-2005  
PXHVW2  
PXHVW2  
PXHVW2  
PXHVW2  
PXHVW2  
PXHVW2  
PXHVW3  
PXHVW3  
PXHVW3  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Config. # 2  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Cabrio  
Eurovan  
Golf  
GTI  
Jetta  
Passat  
Passat  
Phaeton  
Toureg  
1998-2004  
1999-2004  
1998-2005  
1998-2005  
1998-2005  
1998-2003  
2004-2005  
2004-2005  
2004-2005  
7
 
1.5
APPLICATION GUIDE  
GM VEHICLES  
Manufacturer  
/ Fabricant  
Interface  
Location  
Year / Année  
NOTE: 1995-1999 NOT Compatible with In-dash CD Player  
Nota : Non Compatible Avec Le Lecteur De CD Intégré Au Tableau De Bord Des Modèles 1995-1999  
Harness  
Configuration  
Model / Modèle  
Buick  
PXHGM3  
PXHGM3  
PXHGM3  
Config. # 7  
Radio  
Radio  
Radio  
LeSabre  
Rainier  
Rendezvous  
1999-2002  
2005  
2003-2005  
Config. # 7 or 8  
Config. # 7 or 8  
NOTE: 2003-2005 MUST Disable Factory External A/V Source Devices  
Cadillac  
NOTA : Les appareils source audiovisuels externes installés en usine dans les modèles 2003-2005 DOIVENT être  
désactivés.  
NOTE: 1996-1999 NOT Compatible with In-dash CD Player  
Nota : Non Compatible Avec Le Lecteur De CD Intégré Au Tableau De Bord Des Modèles 1996-1999  
PXHGM2  
PXHGM2  
PXHGM1  
PXHGM3  
PXHGM2  
Config. # 6  
Config. # 6  
Trunk  
Trunk  
Deville  
El Dorado  
Escalade  
Escalade  
Seville  
1995-2000  
1995-2002  
1999-2002  
2003-2005  
1995-2005  
Config. # 6  
Radio  
Config. # 7 or 8  
Config. # 6  
Radio  
Console  
NOTE: 2003-2005 MUST Disable Factory External A/V Source Devices  
Chevrolet  
NOTA : Les appareils source audiovisuels externes installés en usine dans les modèles 2003-2005 DOIVENT être  
désactivés.  
NOTE: 1996-1999 NOT Compatible with In-dash CD Player  
Nota : Non Compatible Avec Le Lecteur De CD Intégré Au Tableau De Bord Des Modèles 1996-1999  
PXHGM1  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM3  
PXHGM3  
PXHGM2  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM3  
PXHGM3  
PXHGM1  
PXHGM3  
Config. # 6  
Config. # 6  
Config. # 7 or 8  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 7  
Config. # 7  
Config. # 6  
Config. # 6  
Config. # 7  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 7  
Config. # 6  
Config. # 7  
Config. # 6  
Config. # 7  
Config. # 6  
Config. # 7  
Config. # 7 or 8  
Config. # 6  
Config. # 7 or 8  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Trunk  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Astro Van  
Avalanche  
Avalanche  
Blazer  
1996-2005  
2002  
2003-2005  
1998-2002  
1997-2002  
1996-1999  
2003-2005  
2005  
Camaro  
Cavalier  
Cavalier  
Colorado  
Corvette  
Impala  
Impala  
Lumina  
Malibu  
Monte Carlo  
Monte Carlo  
Silverado  
Silverado  
Suburban  
Suburban  
Tahoe  
1997-2004  
1995-1999  
2000-2005  
1996-1999  
1997-2000  
1995-1999  
2000-2005  
1995-2002  
2003-2005  
1995-2002  
2003-2005  
1995-2002  
2003-2005  
2004-2005  
1997-1999  
2004-2005  
Tahoe  
Trailblazer  
Venture  
Venture  
NOTE: 2003-2005 MUST Disable Factory External A/V Source Devices  
GMC  
NOTA : Les appareils source audiovisuels externes installés en usine dans les modèles 2003-2005 DOIVENT être  
désactivés.  
NOTE: 1996-1999 NOT Compatible with In-dash CD Player  
Nota : Non Compatible Avec Le Lecteur De CD Intégré Au Tableau De Bord Des Modèles 1996-1999  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM3  
Config. # 6  
Config. # 7 or 8  
Config. # 6  
Config. # 7  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 7  
Config. # 6  
Config. # 7  
Config. # 6  
Config. # 7  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Envoy  
Envoy  
Denali  
Denali  
Jimmy  
Sonama  
Safari  
Savana  
Sierra  
1999-2001  
2004-2005  
1995-2002  
2003-2005  
1998-2002  
1998-2002  
1996-2005  
1999-2000  
1995-2002  
2003-2005  
1995-2002  
2003-2005  
1995-2002  
2003-2005  
Sierra  
Suburban  
Suburban  
Yukon/XL  
Yukon/XL  
8
 
1.5
APPLICATION GUIDE  
GM VEHICLES CON
T
.  
Manufacturer  
/ Fabricant  
Interface  
Location  
Year / Année  
Harness  
Configuration  
Model / Modèle  
PXHGM3  
Config. # 7 or 8  
Radio  
H2  
2003-2004  
Hummer  
NOTE: 1995-2001 NOT Compatible with Built-in CD Player  
Oldsmobile  
Nota : Non Compatible Avec Le Lecteur De CD Intégré Au Tableau De Bord Des Modèles 1995-2001  
NOTE: 2004-2005 MUST Disable Factory External A/V Source Devices  
NOTA : Les appareils source audiovisuels externes installés en usine dans les modèles 2004-2005 DOIVENT être  
désactivés.  
PXHGM3  
PXHGM2  
PXHGM3  
PXHGM2  
PXHGM2  
PXHGM1  
PXHGM3  
PXHGM2  
PXHGM2  
PXHGM2  
PXHGM2  
PXHGM2  
PXHGM2  
PXHGM1  
PXHGM3  
Config. # 7  
Config. # 6  
Config. # 8  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 7 or 8  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 7 or 8  
Radio  
Trunk  
Radio  
Trunk  
Trunk  
Radio  
Radio  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
Trunk  
Radio  
Radio  
Achieva  
Alero  
1996-1998  
1999-2000  
2003-2004  
1995-1999  
2001-2004  
1997-2001  
2004  
Alero  
Aurora  
Aurora  
Bravada  
Bravada  
Cutlass  
Cutla Supreme  
Eighty-Eight  
Intrigue  
LSS  
1997-1999  
1995-1997  
1996-1999  
1998-2001  
1996-1999  
1997-1998  
1996-1999  
2004  
Regency  
Silhoette  
Silhoette  
NOTE: 1996-2001 NOT Compatible with Built-in CD Player  
Pontiac  
Nota : Non Compatible Avec Le Lecteur De CD Intégré Au Tableau De Bord Des Modèles 1996-2001  
NOTE: 2004-2005 MUST Disable Factory External A/V Source Devices  
NOTA : Les appareils source audiovisuels externes installés en usine dans les modèles 2004-2005 DOIVENT être  
désactivés.  
PXHGM3  
PXHGM2  
PXHGM1  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM1  
PXHGM3  
PXHGM1  
PXHGM1  
PXHGM3  
Config. # 7 or 8  
Config. # 6  
Radio  
Trunk  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
Aztec  
Bonneville  
Bonneville  
Firebird  
2003-2005  
1996-1999  
2000-2005  
1996-2002  
2003-2005  
1996-2000  
2004-2005  
1999-2000  
1996-1999  
2003-2005  
1996-2002  
1996-1998  
2004-2005  
Config. # 6  
Config. # 6  
Config. # 7 or 8  
Config. # 6  
Grand AM  
Grand AM  
Montana  
Montana  
Sunfire  
Config. # 7 or 8  
Config. # 6  
Config. # 6  
Config. # 7  
Sunfire  
Config. # 6  
Trans Am  
TransSport  
Vibe  
Config. # 6  
Config. # 7 or 8  
PXHGM1  
Config. # 6  
Radio  
SC1  
1995-1999  
Saturn  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM1  
PXHGM1  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Config. # 6  
Radio  
Radio  
Radio  
Radio  
Radio  
Radio  
SC2  
SL  
1995-1999  
1995-1999  
1995-1999  
1995-1999  
1995-1999  
1995-1999  
SL1  
SL2  
SW1  
SW2  
9
 
1.6 Programming the iPod2car  
Now that you have identified the correct harness and dip-switch configuration us-  
ing the application guide, it is now time to program the interface.  
To program the interface, set the dip-switches located on the side of the interface  
(see Fig.1 below) to the congfiguration listed for your vehicle in the Application  
guide. Switches are in their default setting of “off” in the up position and are turned  
“on” when switched down. Refer to the chart on the bottom of this page.  
This programs the iPod2car to the vehicle it is being installed in. The dip-switch-  
es MUST be set before the interface is plugged into the vehicle. Otherwise the  
iPod2car will not work correctly.  
Dip Switch Configuration Chart  
1
2
3
4
5
6
7
8
Config. #1  
Config. #2  
Config. #3  
Config. #4  
Config. #5  
Config. #6  
Config. #7  
Config. #8  
Config. #9  
ON  
ON  
off  
off  
off  
ON  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
off  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
off  
off  
off  
off  
ON  
off  
off  
ON  
ON  
off  
off  
ON  
off  
off  
off  
ON  
ON  
ON  
off  
off  
ON  
off  
off  
off  
ON  
ON  
off  
ON  
ON  
Fig.1 Side view of Interface with dip switches  
1 2  
DIP  
3
4
5
6
7
8
ON  
10  
 
Chapter 2- General Installation  
2.1 Installation Location  
Most installations will require you to remove the factory radio in order to plug in the vehicle  
specific harness. Some vehicles may require you to connect the interface to a factory pre-  
run CD changer cable. The location of these CD changer cables will vary by vehicle. Some  
common locations of these cables are in the trunk, behind the glove box, and in or under a  
center console. ( see Fig.2 below)  
Common Connection Locations  
iPod  
iPod2car  
interface  
MENU  
Vehicle Specific Harness  
2.2 Pre-Installation Checklist  
At this time and before beginning the installation:  
Your iPod’s Firmware should have been updated. (section 1.2)  
You should have your radio’s security code.(when applicable, see section 1.2)  
• The dip-switches on the interface should have been set with the proper configuration.  
(see section 1.3)  
You should have in your possession the correct harness for your vehicle. (see sec 1.3)  
You have determined your installation location. (see section 2.1)  
If any of these steps has not been taken, STOP. Only when ALL of these steps have been  
taken should you proceed with the rest of the installation.  
2.3 Wiring Connections  
Some vehicle specific harnesses require wiring connections that involve splicing of wires. If  
you are not confident in making these connections to your radio’s wiring harness, we recom-  
mend you seek professional installation. You can visit www.iPod2car.com and click on the  
dealer link at the top of the page to find an authorized professional installer.  
11  
 
Make these connections only after verifying the proper circuit on your radio harness with a  
voltmeter. With the key OFF and the negative test lead of the voltmeter firmly touching a  
bare metal chassis part of your car, begin probing the wires in the main radio harness with  
the positive test lead. The constant 12V+ circuit should read a continuous 12 volts or higher.  
Once you’ve identified the constant 12V+ circuit, strip back about 1/8” of the insulation. Now  
take the positive test lead and insert it into the wire stranding so that you can now probe for a  
suitable ground location in the dash cavity using the negative test lead. Bare chassis metal  
is the recommended ground spot. The voltmeter will read a constant 12 volts or higher when  
you have found a good ground point. Attach the BLACK ground wire to this spot with either  
an existing bolt or screw or use a metal piercing screw. You also have the option of splicing  
into the ground wire in the main radio harness. Probe the remaining wires with the negative  
test lead until you again find a circuit that reads a constant 12 volts on the voltmeter. When  
you’ve found a circuit that reads constant 12 volts, turn the dash light dimmer control to make  
sure you have not probed the illumination dimmer circuit. If the circuit continues to read a  
constant 12 volts or higher regardless of the dimmer position, you have found the ground  
wire. If not, continue testing until you do. Some vehicles do not have a ground wire in their  
main radio harness and instead ground through their mounting brackets to the dash. In these  
cases, you will have to ground the black wire to the bare metal chassis inside the dash . Once  
the ground wire is connected, please finish your wiring connections by splicing in the external  
YELLOW wire from the vehicle specific harness.  
Vehicle Specific Harnesses that require wiring connections:  
PXHFD1 – connect the Yellow wire to constant 12V+ & connect the Black wire to ground.  
PXHFD2 – connect the Yellow wire to constant 12V+ & connect the Black wire to ground.  
PXHFD3 – connect the Yellow wire to constant 12V+ & connect the Black wire to ground.  
PXHGM3 – connect the Yellow wire to constant 12V+ & connect the Black wire to ground.  
PXHVW2 – connect both the Black and Black/White wires to ground.  
2.4 Installation at the CD Changer Location  
In this section you will learn how to install the iPod2car in the factory CD changer location. If your  
vehicle is equipped with a factory CD changer you will need to disconnect it from the factory pre-run  
harness in order to connect the iPod2car interface. If your vehicle is not equipped with a factory  
CD changer, you will need to locate the factory pre-run harness. This may involve the removal of  
the; center console, glove box, or carpeted side panels in the trunk. Please consult your vehicle’s  
dealership or a local car audio professional for instruction or assistance with locating the factory CD  
changer connection if necessary.  
1. Connect your vehicle specific Harness to the factory pre-run CD changer harness in the ve-  
hicle.  
2. Make any necessary wiring connections on your vehicle specific harness. Please see section 2.3  
for details on making these wiring connections.  
3. Now that the interface is connected to the radio, you will need to test the operation of the interface  
before permanently running the white iPod docking cable or re-assembling the dash. First, connect  
the white iPod cable to the iPod. The iPod should indicate that it is being charged. Turn on the fac-  
tory radio and press the button that would activate the factory CD changer to select the iPod. It may  
take up to three minutes for the interface to initialize to the radio (this only happens the very first  
time you select the iPod). Once the iPod has been selected, press Play on the iPod. You should  
be able to hear the music on your iPod through your factory radio. Now press the “Next Track” but-  
ton on the radio. The iPod should change to the next song on the iPod. By pressing the “Previous  
Track” button on the radio the iPod should change to the previous song. With the operation of the  
interface confirmed, you may continue with the installation. If you experience difficulties in opera-  
tion, please see our troubleshooting chart in section 3.2.  
Continued on next page  
12  
 
4. Decide on a convenient location to mount your iPod.  
5. Run the white docking cable from the interface to the desired mounting location. Use caution to  
not cut, pinch, or crimp the cable during this step. Avoid moving parts, vehicle wiring harnesses and  
areas of excessive heat when routing the cable.  
6. Secure the interface in the vehicle using; double sided tape, Velcro or wire ties. Make sure to  
check for proper clearance and avoid moving parts. Take into account the size of the interface and  
the wire harness and do not force the interface and harness into a space that is too tight, damage  
to the harness may result.  
7. Now that the interface is secured and the docking cable has been run, you are ready to enjoy  
your iPod in your vehicle!  
2.5 Installation at the Radio  
In this section you will learn how to install the iPod2car behind the radio. If your vehicle is  
equipped with a factory CD changer or other external audio source, you will need to discon-  
nect it from the back of the radio in order to connect the iPod2car interface.  
1. Carefully remove the radio from the vehicle. If your radio uses a Security Code, make sure  
that you have the code before unplugging the radio. Some vehicles require the use of special  
tools to remove the radio. Please consult your vehicle’s dealership or a local car audio pro-  
fessional for instruction or assistance with radio removal if necessary.  
2. Make any necessary wiring connections on your vehicle specific harness. Please see  
section 2.3 for details on making these wiring connections  
3. Connect the Vehicle Specific Harness to the CD changer port on the back of the radio. Be  
sure to make a firm connection but do not force it. If there is difficulty making the connection,  
please consult the application guide to confirm your vehicle specific harness selection.  
4. Now that the interface is connected to the radio, you will need to test the operation of the  
interface before permanently running the white iPod docking cable or re-assembling the  
dash. First, connect the white iPod cable to the iPod. The iPod should indicate that it is be-  
ing charged. Turn on the factory radio and press the button that would activate the factory  
CD changer to select the iPod. It may take up to three minutes for the interface to initialize  
to the radio (this only happens the very first time you select the iPod). Once the iPod has  
been selected, press Play on the iPod. You should be able to hear the music on your iPod  
through your factory radio. Now press the “Next Track” button on the radio. The iPod should  
change to the next song on the iPod. By pressing the “Previous Track” button on the radio  
the iPod should change to the previous song. With the operation of the interface confirmed,  
you may continue with the installation. If you experience difficulties in operation, please see  
our troubleshooting chart in section 3.2.  
5. Decide on a convenient location to mount your iPod.  
6. Run the white docking cable from the interface to the desired mounting location. Use cau-  
tion to not cut, pinch, or crimp the cable during this step. Avoid moving parts, vehicle wiring  
harnesses and areas of excessive heat when routing the cable.  
7. Secure the interface in the dash cavity behind the radio using; double sided tape, Velcro or  
wire ties. Make sure to check for proper clearance and avoid moving parts. Take into account  
the size of the interface and the wire harness and do not force the interface and harness into  
a space that is too tight, damage to the harness may result.  
8. Now that the interface is secured and the docking cable has been run, you may reinstall  
the radio and replace any panels that may have been removed to access the radio. You are  
ready to enjoy your iPod in your vehicle!  
13  
 
Chapter 3- Operation  
3.1 Operation  
SELECTING THE IPOD  
To select the iPod from the radio, press the button that would normally activate  
the factory CD changer. This button varies by vehicle manufacturers. In some  
applications (using config.#8) the iPod2car is accessed like an XM reciever, In  
these cases you will press the appropriate activation button. Some radio models  
require pressing the “Seek >” button once, after pressing the CD button. Yet,  
it may also be necessary to press Play on the iPod itself to begin playback. In  
some cases, if it is the first time selecting the iPod from the radio it may take up  
to three minutes for the iPod2car to initialize.  
CONTROLLING THE IPOD FROM THE RADIO  
With the iPod2car interface, the radio will control the iPod as if it were a factory  
CD changer. Therefore, operation will be done by using the same buttons you  
would use to control a factory CD changer. For more details on your particular  
radio, consult your vehicle’s owner’s manual.  
The iPod2car interface allows you to skip songs forward and backwards and also  
to fast forward and rewind through a particular song. In general, most radios will  
utilize “seek” or “track” buttons to control these functions.  
CONTROLING THE IPOD FROM THE IPOD  
The iPod2car interface allows you to keep full control of the iPod from the click  
wheel. You can browse files and change playlist on the iPod. You can also skip  
songs forward and backwards from the iPod. The iPod2car interface does not  
disable any functionality of the iPod!  
RADIO DISPLAY DURING IPOD OPERTION  
Some factory radio’s may show DISC and TRACK numbers on the display of the  
radio. The iPod2car interface does not send any information from the iPod to the  
radio. This means that the DISC and TRACK numbers shown on the display will  
not and can not reflect the song number on the iPod due to the complex nature  
of the music library. Some factory radio’s may flash zero’s on the display of the  
radio, or toggle back and forth between Tracks “1” and “2”. All these are normal  
behaviors and do not represent a malfunction.  
CONTROLING THE IPOD FROM THE STEERING WHEEL CONTROLS  
If your vehicle’s steering wheel controls have the ability to select track and control  
the forward and rewind functions of your factory CD changer, then they will also  
control these same functions on the iPod.  
14  
 
3.2 Trouble Shooting  
Symptom  
No Power  
Cause  
Remedy  
Blown fuse in vehicle fuse  
block.  
Replace fuse with same  
amp rating. If the fuse  
blows again, call tech  
support.  
No Power  
Bad connection  
Check cable and wiring  
connection.  
Alternator noise is heard  
(Changes with Engine RPM) ground loop  
Improper wiring creates a  
Install a Ground loop isola-  
tor or seek professional  
service from a local car  
audio shop.  
You can hear music from  
the iPod but you cant con-  
trol it from the radio.  
The Firmware on the iPod  
may not be updated.  
Update the Firmware on  
the iPod. See section 1.2  
of this manual.  
Radio is not recognizing  
iPod2car interface  
Bad cables or cables are  
not connected properly  
between converter box and  
car radio  
Check connection and  
cables, push in firmly.  
Radio is not recognizing  
iPod2car interface  
Wrong configuration on the  
interface  
Select the right pconfigu-  
ration for your car. (See  
section 1.5)  
Radio is not recognizing  
iPod2car interface  
Yellow and black wires are  
not connected to Constant  
12V+ and Ground. (When  
applicable)  
Please read wiring instruc-  
tions in chapter 2 of this  
manual and see if your car  
requires to connect the  
yellow and black cable to  
power and ground  
iPod Audio is Low or  
Distorted  
iPod2car interface is con-  
nected with an external CD  
changer or other external  
factory audio source  
Disconnect the factory  
external audio source.  
iPod is not charging  
Yellow and black wires are  
not connected to Constant  
12V+ and Ground. (When  
applicable)  
Please read your vehicles  
section in this manual and  
see if your car requires to  
connect the yellow and  
black cable to power and  
ground  
For consumer technical support call:  
866-788-4237 in the US or 727-572-9255 ext.262 for international calls  
Hours: 9:30 am-6:00 pm E.S.T. MON - FRI  
15  
 
3.3 Warranty  
One Year Limited Warranty  
The quality controls used in the manufacture of this product will ensure your satisfaction.  
This warranty applies only to the original purchaser of this product from an authorized  
Peripheral Elecronics dealer.  
This warranty covers any supplied or manufactured parts of this product that, upon inspec-  
tion by Peripheral Electronics authorized personnel, is found to have failed in normal use  
due to defects in material or workmanship. This warranty does not apply to installation  
expenses.  
Attempting to service or modify this unit, operating this unit under conditions other than the  
recommended voltage will render this WARRANTY VOID.  
Unless otherwise prescribed by law, Peripheral Electronics shall not be liable for any per-  
sonal injury, property damage and or any incidental or consequential damages of any kind  
(including water damage) resulting from malfunctions, defects, misuse, improper installation  
or alteration of this product.  
All parts of this Peripheral Electronics product are guaranteed for a period of 1 year as  
follows:  
Within the first 12 months from date of purchase, subject to the conditions above, Peripher-  
al Electronics will repair or replace the product at their discretion, if it is defective in material  
or workmanship providing it is returned to an Authorized Peripheral Electronic’s Dealer, with  
PROOF OF PURCHASE from an authorized Peripheral Elecronics dealer.  
3.4 Warning:  
This equipment may be reset by unintentional electrostatic discharge during operation.  
Exposure to direct sunlight or extreme heat may cause damage or malfunction.  
3.5 FCC Class B Radio Frequency  
Interference Statement  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of FCC rules. These limits are designed to provide reason-  
able protection against harmful interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television recption, which can  
be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
1. Reorientate or relocate the receiving antenna.  
2. Increase the separation between the equipment and reciever.  
3. Connect the equipment into an outlet on a circuit differant from that of which  
the reciever is connected.  
4. Consult the dealer or an experienced radio / television technical for help  
Notice : The changes or modifications not expressly approved by the party responsible for  
compliance could void the user authority to operate the equipment.  
16  
 
 
Please check out our other products including:  
Aux2car  
(PXDX)  
Programmable auxiliary input device  
CD2car  
(PCD10)  
Complete universal CD changer that connects to  
most factory stereos  
Peripheral Electronics®,  
a division of AAMP of America™  
13160 56th Court Clearwater, Florida 33760  
866-788-4237 in the US or 727-572-9255 ext.262 for international calls  
©2005 AAMP™ of Florida, Inc.  
 

Peavey Guitar S Active User Manual
Peavey Music Mixer XRD 680S Plus User Manual
Pelco Digital Camera CCC1380H 6X User Manual
Philips Answering Machine Elegance 55 User Manual
Philips Cassette Player AQ6401 User Manual
Philips Juicer RI1865 User Manual
Philips MP3 Player AD7000W 37 User Manual
Philips TV DVD Combo DVDR3460 User Manual
Planet Technology Network Router WNRT 620 User Manual
Playskool Baby Toy 5507 User Manual