Perle Systems TV Converter Box 5500316 13 User Manual

Perle SMI Media Converter  
Installation Guide  
P/N 5500316-13  
 
100/110 Models  
(xxx)  
1000/1110 Models  
(xxxx)  
Connector  
(cc)  
Wavelength  
(TX/RX)  
Mode  
Distance  
10 km  
6.2 mi.  
SMI-xxxx-S2cc10  
SMI-xxxx-S1SC10U  
SMI-xxxx-S1SC10D  
SMI-xxxx-S1SC20U  
SMI-xxxx-S1SC20D  
SMI-xxxx-S2cc40  
SMI-xxxx-S1SC40U  
SMI-xxxx-S1SC40D  
SMI-xxxx-S2cc70  
SMI-xxxx-S1SC80U  
SMI-xxxx-S1SC80D  
SMI-xxxx-S2cc120  
SMI-xxxx-S1SC120U  
SMI-xxxx-S1SC120D  
SMI-xxxx-S2cc160  
SMI-xxxx-SFP  
SC/ST/LC  
SC  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
Note 1  
1310/1310 nm  
1310/1490 nm  
1490/1310 nm  
1310/1490 nm  
1490/1310 nm  
1310 /1310 nm  
1310/1490 nm  
1490/1310 nm  
1550/1550 nm  
1510/1590 nm  
1590/1510 nm  
1550/1550 nm  
1510/1590 nm  
1590/1510 nm  
1550/1550 nm  
10 km  
6.2 mi.  
10 km  
6.2 mi.  
SC  
20 km  
12.4 mi.  
SC  
20 km  
12.4 mi.  
SC  
40 km  
25 mi.  
SC/ST/LC  
SC  
40 km  
25 mi.  
40 km  
25 mi.  
SC  
70 km  
43.5 mi.  
SC/ST/LC  
SC  
80 km  
50 mi.  
80 km  
50 mi.  
SC  
120 km  
74.6 mi.  
SC/ST/LC  
SC  
120 km  
74.6 mi.  
120 km  
74.6 mi.  
SC  
160 km  
100 mi.  
SC/ST/LC  
SPF  
Note 1  
Please visit Perle’s web site for the most up to date  
Installation guides, models and specifications:  
Perle SMI Media Converter Guide 3  
 
Getting to know your SMI Media  
Converter  
Unpacking your SMI Media Converter  
Your SMI Media Converter consists of the following items:  
A MCR-MGT Management card  
See section in this guide for setting up your MCR-MGT  
Management Module  
Media Converter module  
See enclosed Media Converter Installation guide for  
usage and features for your module. These may include  
Link Mode, Fiber Fault Alerts, Loopback and more.  
SMI chassis  
Two slot chassis  
Other Components  
Grounding screws (for improved chassis grounding)  
Country specific power adapter  
Power cord strain relief clip  
Four rubber feet  
User installation guide for the Media Converter Module  
CDROM including firmware for the MCR-MGT  
Management Module and Media Modules, MCR-MGT  
Management module User guide and MCR-MGT  
Management module CLI guide.  
This guide  
Perle SMI Media Converter Guide 4  
 
Front and Rear Panel Components  
Front View  
Rear View  
Perle SMI Media Converter Guide 5  
 
Installation  
These steps are needed to get fiber connectivity.  
1. Connect the fiber cable.  
2. Connect the copper cables.  
3. Power up the SMI Media Converter.  
4. Both the power led indicator lights on the MCR-MGT  
management module and the media module should be  
illuminated. (Refer to the product guide that came with  
your SMI Media Converter for individual LED definitions).  
Powering up the SMI Media Converter  
Note: The SMI Chassis should always be grounded for safe and  
proper operation. See Grounding the SMI Chassis  
1. Using the Perle supplied power adapter, plug the power  
cord into the power cord connector at the rear of the  
chassis.  
2. Plug the other end of the power adapter into an  
appropriate power outlet.  
See the media converter module guide that came with your  
SMI Media Converter to access media converter module  
features:  
LEDs  
DIP switch settings  
Jumper settings  
Adding or Removing Modules:  
The Media Converter Module may need to be removed for  
setting jumpers or DIP switches, if the defaults are not  
Perle SMI Media Converter Guide 6  
 
appropriate. Also, either module can be removed should  
servicing be required.  
Caution: Observe electrostatic discharge precautions when  
installing or removing the Module(s) from the Chassis.  
Failure to observe this caution could result in damage to the  
Module(s) and/or chassis.  
1. Loosen the Captive retainer screw on the front of the  
module.  
2. Gently pull the module towards you.  
3. Set any jumpers and/or DIP switches on the Module to  
the desired operating mode. (Refer to the product guides  
that came with your SMI Media Converter).  
4. Gently slide the module back into the slot until it  
becomes flush with the front of the chassis. Light  
pressure may be needed to seat the module. Do not  
force the module as you might damage the module. If  
there is resistance, remove the module and check the  
module’s backplane connector for damage to the pins. If  
the module’s backplane connector is not damaged, try to  
reinsert the module again  
5. Tighten the Captive retainer screw to ensure the module  
is locked in place.  
Perle SMI Media Converter Guide 7  
 
Grounding the SMI Chassis (Optional)  
If your installation requires additional grounding the following  
procedure can be followed.  
Grounding the chassis requires the following items:  
One grounding lug (not provided)  
One 18 - 12 AWG wire (not provided)  
Cross-head screwdriver (not provided)  
Note: For your safety, when installing this equipment, always  
ensure that the chassis ground connection is installed first  
and disconnected last.  
Attaching the Grounding Lug  
1. Attach the grounding lug to one end of an 18-12 AWG  
wire.  
2. Attach the grounding lug to the chassis and secure with  
the grounding screw(s).  
Attaching the Power Cord Strain Relief Clip  
1. Feed the power cord through the opening in the power  
cord relief clip.  
Perle SMI Media Converter Guide 8  
 
2. Attach the power cord relief clip to the chassis and  
secure with the provided screw.  
3. Plug the power cord into the AC power connector at the  
rear of the chassis.  
4. Plug the other end of the power cord into an appropriate  
power outlet.  
Perle SMI Media Converter Guide 9  
 
MCR-MGT Management Module  
Your SMI Media Converter comes with a powerful MCR-  
MGT Management Module that allows you to configure,  
monitor and control your SMI Media Converter.  
Features  
Management access through AAA security such as  
RADIUS, TACACS+, LDAP, Kerberos and NIS.  
IPv4 and IPv6 network environments.  
Central management and configuration through SNMPv3  
as well as SNMPv1/2.  
Management module access via Browser, Telnet or SSH  
over 10/100/1000 Mbps Ethernet.  
Cisco pin-compatible RJ-45 console port on  
Management module for easy cabling connections.  
Local Event logging and Syslog  
Quickly restore manufacturing configuration settings.  
Making Connections to the  
Management Module  
Connecting To The LAN  
Depending on the speed at which you plan to operate your  
Ethernet connection, locate compliant copper cables with  
male, RJ-45 connectors installed at both ends.  
Connect the RJ-45 cable between the MCR-MGT Ethernet  
port and the hub or switch port which will connect the  
module to your Ethernet LAN.  
Note: The MCR-MGT module supports Auto MDI/MDIX detection  
which allows for the use of a straight-through or cross-over  
Ethernet cable.  
Perle SMI Media Converter Guide 10  
 
Connecting To The Console Port  
This is a serial connection. It will allow you to connect a  
terminal or PC with terminal emulation software to the  
console port of the Management module.  
The following is the cable pinout required to connect the  
console port to a DB-9 port on the PC.  
MCR-MGT  
PC  
Management Module  
DB9 serial  
8 (CTS)  
6 (DSR)  
2 (RxD)  
5 (GND)  
3 (TxD)  
4 (DTR)  
7 (RTS)  
RJ-45 Console Port  
1 (RTS)  
2 (DTR)  
3 (TxD)  
5 (GND)  
6 (RxD)  
7 (DSR)  
8 (CTS)  
Alternately, you can purchase the following two parts from  
Perle Systems Limited.  
3ft RJ-45 straight through cable. Part #:04005120  
RJ-45 to DB9F-DTE (console adapter). Part #:04007040  
Perle SMI Media Converter Guide 11  
 
Configuring the Management-MGT  
Module  
There are a number of methods which may be used to  
configure the MCR-MGT management module:  
Command Line or Menu interface via a direct serial  
connection to the console port  
Command Line or Menu interface via Telnet or SSH to  
module  
SNMP  
Web Browser (HTTP or HTTPS)  
All of the above methods require you to configure an IP  
address on the management card to be able to connect and  
configure the module except for the direct serial connection  
which you can connect directly to the console port. The  
management module is pre-configured with an IP address of  
10.0.0.10 with a subnet mask of 255.0.0.0. If the PC that  
you are using does not reside on this subnet, you will need  
to modify either the IP address of the MCR-MGT  
management module (using a direct serial connection to the  
Management module) or the pc’s IP address in order to  
connect and configure the Management module.  
The following are two methods in which to set the IP  
address of the MCR-MGT Management module.  
Perle SetIP Utility  
On the CD provided with the MCR-MGT module, you will  
find an executable called “Perle SetIP”. You can run it  
directly from the CD or copy it to your local PC drive and  
execute it from there  
.
When the program runs, you can do the following;  
1. From the list of devices displayed, click on the MCR-  
MGT module you wish to set the IP address on and then  
Perle SMI Media Converter Guide 12  
 
click on the “Assign IP” button at the top of the screen.  
Please note that this operation will only be valid on  
MCR-MGT modules which are in a “factory default”  
state.  
2. To manually assign the IP address, click on “Assign IP  
manually”, key in the desired IP address and press the  
“Assign IP” button. If a DHCP server is available on this  
subnet, you can choose to have the module obtain its IP  
address via your DHCP server by clicking on the “Assign  
IP using DHCP” button and then pressing the “Assign IP”  
button.  
3. For modules which have been assigned IP address, you  
can click on the “manage” button on the top of the  
screen to launch a web browser session with the  
selected MCR-MGT module. You can achieve the same  
result by manually launching your web browser and  
entering the IP address of the module in the web  
browsers address field.  
4. You can also use Telnet, SSH or SNMP to configure the  
module.  
Serial Console Port  
Using the proper cable connector, connect the Management  
module to the serial port on your PC. Perle Systems has  
available for purchase an RJ-45 to DB9F-DTE console  
adapter (part #04007040) which can be used in conjunction  
with an RJ-45 patch cable (part #04005120) to connect your  
PC’s serial port to the Management module’s console port.  
Set the communication parameters on your PC’s terminal  
emulation program to 9600,8,n,1.  
1. Press [Enter]. The management module prompt will  
appear.  
Perle SMI Media Converter Guide 13  
 
2. Type set server internet <IPv4 address>netmask  
<mask>[Enter]  
Example:  
set server internet 196.12.10.9 netmask  
255.255.255.0[Enter]  
1. Type save [Enter]  
2. When prompted “Save config to flash ROM y/n” [Enter]  
3. Type reboot [Enter]  
4. When prompted “Confirm reboot unit y/n [Enter]  
5. When the Management module reboots, the IP address  
you entered will be active. You can now use your  
favourite web browser to configure the module. Simply  
enter the IP address in the web browsers address field  
and press [Enter].  
6. You can also use Telnet, SSH or SNMP to configure the  
Management module.  
Resetting the MCR-MGT Management Module To  
Factory Default Settings  
If it becomes necessary to return the Management module  
to the factory default settings, press and hold the “RESET”  
button on the front of the module for 3 seconds (you can use  
a paper clip to do this). This will return the configuration to  
the factory default settings and will force the module to  
reboot.  
Perle SMI Media Converter Guide 14  
 
LED Status for the Management  
Module  
The MCR-MGT module has four status LEDs, which are  
used to monitor the operational status of the MCR-MGT  
Module in the network and the status of the MCR1900  
Chassis.  
ALM - Alarm  
Off - No faults detected.  
Red - A severe or critical level fault has been detected in the  
system.  
PWR - Power  
Green - Power is on and the module is in normal operation  
mode.  
Green blinking - The MCR-MGT Module is initializing. The  
bootup should complete within 1 minute, at which time the  
PWR LED should go solid green.  
Off - The MCR-MGT module has no power.  
Red - Unrecoverable hardware error on MCR-MGT module.  
Perle SMI Media Converter Guide 15  
 
LKC - Copper –Link/Activity  
On - Copper link is up.  
Off - Copper link is down.  
Blinking (quickly) - Copper link is up and is sending or  
receiving data.  
100/1000  
Green - The Ethernet speed on the management module is  
detected at 1000 Mbps (Gigabit).  
Yellow - The Ethernet speed on the management module is  
detected at 100 Mbps.  
Off - The Ethernet speed on the management module is  
detected at 10 Mbps  
Perle SMI Media Converter Guide 16  
 
Troubleshooting  
General  
Ensure power is supplied to the Media Converter – use  
of the supplied power adapter is highly recommended.  
Ensure that the Media Converter Module and MCR-MGT  
Management Module are securely seated in the chassis  
See Adding or Removing Modules.  
Ensure both devices on either end of the fiber are  
compatible. If using a simplex fiber connection, ensure  
that you have both an Upstream (U) and Downstream  
(D) Media Converter.  
Ensure all cabling is of the correct type and is in good  
working order.  
For duplex fiber connections, ensure the RX and TX has  
been reversed between the two Media Converters.  
No connectivity  
Refer to the media converter guide that came with your SMI  
Media Converter.  
Loopback Mode  
The fiber connection can also be verified by configuring the  
SMI Media Converter for loopback mode. Refer to the Media  
converter guide that came with your SMI Media Converter  
for DIP switch setup.  
MCR-MGT “PWR” LED is OFF  
Ensure that the management module is inserted into the  
chassis correctly. See Adding or Removing Modules.  
Ensure that the MCR Chassis is connected to an external  
power source.  
Perle SMI Media Converter Guide 17  
 
MCR-MGT “PWR” LED is RED  
The MCR-MGT module is defective. It will need to be  
replaced.  
MCR-MGT “PWR” LED is Blinking Green  
The MCR-MGT module is in the process of booting up. If this  
state persists for longer then one minute, reset the module by  
momentarily pressing the reset switch on the front of the module.  
See Front view – reset switch.  
Cannot connect serially to MCR-MGT Module  
1. Make sure that the PWR LED is “Green”  
2. Ensure that you are using the right cable/adapter.  
3. If you see garbage characters, the baud rate of the serial  
port may have been changed from the original 9600  
baud. Configure your terminal emulation to match  
configured speed.  
4. If you don’t know what the speed is, you could reset the  
module to “factory default” by pressing and holding the  
reset switch (3 seconds) on the front of the MCR-MGT  
module. NOTE: this will erase the entire configuration  
back to a factory default state.  
Cannot connect to MCR-MGT Module using an IP  
address  
1. Make sure that the PWR LED is “Green”  
2. Make sure that the LKC LED is “Green”. (Copper link  
connection is up).  
3. Make sure you are using the IP address which is  
configured on the MCR-MGT module.  
Perle SMI Media Converter Guide 18  
 
4. If you don’t know what the IP address is, you can use  
the “SetIP” utility provided on the CD to display the IP  
address of all units on your LAN segment.  
Perle SMI Media Converter Guide 19  
 
Technical Specifications for the SMI Media  
Converter  
The following applies to all SMI-xxxx Media Converters:  
Max Power Input/Consumption: 12 V DC/15 Watts  
Operating Temperature:  
Storage Temperature:  
Operating Humidity:  
Storage Humidity:  
Operating Altitude:  
Weight without cards:  
Weight with cards:  
Dimensions  
0°C - 50°C (32°F - 122°F)  
-25°C - 70°C (-13°F - 158°F)  
5% to 90% non-condensing  
5% to 95% non-condensing  
Up to 3,048 m (10,000 ft)  
0.566 kg (1.25 Lbs.)  
0.722 kg (1.59 Lbs.)  
175 mm 145 mm by 23 m  
6.9” in. by 5.7” in. by .90” in.  
MTBF (Hours)  
excluding  
Power  
MTBF (Hours)  
including  
Power  
Power  
Model  
Current  
(@ 12 V DC)  
Consumption  
adapter  
adapter  
SMI-1000  
4.98 watts  
4.98 watts  
4.1 watts  
4.1 watts  
3.98 watts  
4.1 watts  
0.42 amps  
0.42 amps  
0.34 amps  
0.34 amps  
0.33 amps  
0.34 amps  
248,259  
268,167  
238,087  
256,533  
245,769  
246,403  
169,698  
SMI-1000-SFP  
SMI-1110  
178,770  
164,883  
173,524  
168,532  
168,829  
SMI-1110-SFP  
SMI-100  
SMI-110  
Perle SMI Media Converter Guide 20  
 
Ethernet Copper Cabling  
Category 5 UTP or STP  
24-22 AWG Straight through or Ethernet crossover  
Console Port Cabling Requirements  
Pinout  
Console Port  
1
2
3
4
5
6
7
8
RTS (out)  
DTR (out)  
TxD (out)  
GND  
GND  
RxD  
DSR (in)  
CTS (in)  
Note: Please refer to the product page on the Perle website  
for the most up to date specifications  
.
Perle SMI Media Converter Guide 21  
 
Compliance Information  
FCC  
This product has been found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC rules. These limits are designed to provide  
reasonable protection against harmful interference when the equipment is operated  
in a commercial environment. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in accordance with the  
instructions in this Guide, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference, in which case the user will be required to correct the interference at  
his/her own expense.  
EN 55022 Class A  
WARNING This is a Class A product. In a domestic environment this product may  
cause radio interference in which case the user may be required to take adequate  
measures.  
EN 55024 Class A  
Laser Safety – IEC 60825-1:2007  
This product meets Class I Laser safety requirements per IEC-60825-1:2007  
standard and complies with FDA/CDRH 21 CFR1040.10 and 21 CFR1040.11.  
WARNING: Visible and invisible laser radiation may be present when cables are  
not connected. Do not stare into the beam or view the beam directly with optical  
instruments. Failure to observe this warning could result in an eye injury or  
blindness.  
WARNING: Use of controls, adjustments or the performance of procedures other  
than those specified herein may result in hazardous radiation exposure.  
Perle SMI Media Converter Guide 22  
 
Warranty / Registration  
Perle’s Systems Ltd. standard Lifetime Warranty provides  
customers with return to factory repairs for Perle products  
that fail under the conditions of the warranty coverage.  
Details can be found at:  
Contacting Technical Support  
Contact information for the Perle Technical Assistance  
Center (PTAC) can be found at the link below. A Technical  
Support Query may be made via this web page.  
Copyright  
© 2011 Perle Systems Limited  
All rights reserved. No part of this document may be reproduced or used in any  
form without written permission from Perle Systems.  
Perle SMI Media Converter Guide 23  
 

Philips CRT Television 170X4 User Manual
Philips Iron GC3240 User Manual
Philips Speaker System MCM275 User Manual
Philips Work Light 66702 User Manual
Phoenix Gold Speaker TI65CS User Manual
Pinnacle Design TV Video Accessories TV51101 User Manual
Pioneer Speaker SP C22 User Manual
Polaris Offroad Vehicle 450 MXR LE User Manual
Polk Audio Speaker f x1000 User Manual
Poulan Snow Blower 192039 User Manual