Phase Technology Portable Speaker SM590i User Manual

Surface-Mount Speaker  
SM590i  
Preliminary Technical Information for System Engineers  
Key Features  
• High-power output (108.5 dB) for longer  
throw and higher SPL requirements.  
• One 133 mm (5.25 in) polypropylene  
woofer and one 25 mm (1.0 in) horn-  
loaded convex aluminum dome tweeter  
mounted to a proprietary cast-alumi-  
num HP5TM baffle & heat sink.  
Mounting hardware included  
Specifications: SM590i  
System Type  
5.25” Coax, open-ceiling, ported (33 Watt transformer for  
• 89.5 dB Average sensitivity offers high  
output capabilities and reduced amplifi-  
cation costs.  
25/70.7/100 Volt or voice coil / 8 Ohm direct)  
71 Hz - 22 kHz  
61 Hz - 20 kHz  
160 Watts  
80 Watts  
108.5 dB  
89.5 dB  
8 Ohm (nominal value)  
166º (average)  
88º (average)  
5.69 (Averaged 100 Hz - 10 kHz); 5.87 @ 2 kHz  
6.12 dB (Averaged 100 Hz - 10 kHz); 7.69 dB @ 2 kHz  
6-Position rotary switch with voice coil direct (8 Ohm)  
Frequency Response (- 3 dB)1  
Low Frequnecy (-10 dB)1  
Max. Program Power  
• Weatherized components for indoor/  
outdoor applications. Includes a  
tool-free SpeedLeverTM captured ball  
mounting system for a fast & secure  
installation.  
Max. Continuous Power RMS2  
Max. SPL dB @ 1 M  
Sensitivity dB @ 1W/1M3  
Impedance (nominal)  
Coverage Angle (-6 dB @ 500 Hz)  
Coverage Angle (-6 dB @ 4 kHz)  
Directivity Factor (Q)  
• Included accessories: Mounting hard-  
ware, Euroblock connector & terminal  
weather boot.  
Directivity Index (DI)  
Tap Selector  
• Vertical and horizontal pivoting offer  
precision aiming for indoor & outdoor  
applications.  
Transformer Taps  
70.7 V Output  
33 W 104.5 dB  
17 W 102 dB  
9 W 99 dB  
6 W 97.5 dB  
3 W 97.5 dB  
100 V Output  
33 W 104.5 dB  
17 W 102 dB  
9 W 99 dB  
25 V Output  
5 W 96.5 dB  
2.5 W 93.5 dB  
1.3 W 90.5 dB  
0.63 W 87.5 dB  
• Easy access 6-position selectable tap  
switch for 25, 70.7 & 100 Volt applica-  
tions with voice coil/8 Ohm direct sim-  
plifies ordering and inventory tracking.  
6 W 97.5 dB  
• Optional accessories: Pole-Mount Adap-  
tor, Bent Shaft, U-Bracket.  
Transducers  
Low Frequency Driver  
High Frequency Driver  
Low Frequency Voice Coil  
Crossover Frequency  
1 x 133 mm (5.25 in) Polypropylene cone, butyl rubber surround  
25 mm (1.0 in) Convex aluminum horn-loaded tweeter  
25 mm (1.0 in)  
3 kHz  
• High quality black or white paint finish.  
Description  
Network Type  
Low Pass  
High Pass  
Enclosure Material  
Motor Board  
Grille  
Inputs  
Colors  
Length  
Height  
The SM590i is a high-powered 5.25”  
2-way horn-loaded loudspeaker in a ported  
surface-mount enclosure design. The SM590i  
incorporates a low-profile grille, proprietary  
HP5TM motor-board and 6-position tap  
switch with voice coil/8 Ohm direct. Hang-  
ing hardware is included and features a  
fast-action Speed-LeverTM for easy and secure  
installation with a proprietary captured ball  
mounting system. Optional accessories  
include a pole mount adaptor, a bent shaft  
and a u-bracket.  
N/A  
12 dB per octave, 2nd order  
Drawn aluminum backcan with ABS baffle  
Cast aluminum  
Iridite-plated steel with powder-coat finish  
4 Pin, 5 mm Euroblock for individual or daisy chain connection  
Black or white  
305.1 mm / 12.01 in  
316.9 mm / 12.48 in  
216.6mm / 8.53 in  
4.3 kG / 9.5 lbs  
Width (including bracket)  
Weight  
Shipping Weight  
10 kG / 22.0 lbs (2 per box)  
Accessories  
Included  
Hanging hardware, Euroblock connector & terminal  
weather boot  
Applications  
Engineered for high-SPL and effective  
low-end response (61 Hz @ - 10 dB), the  
SM590i delivers consistent high-perfor-  
mance music and paging for applications  
requiring longer throw or higher volume  
above the existing ambient noise level.  
The SM590i is ideal for suface-mount  
sound reinforcement/PA in applications  
with high ambient noise levels including  
casinos, warehouses, airports, transporta-  
Optional  
U-Mount Bracket (AC-SM-UB5), Pole Mount Adaptor  
(AC-SM-PMA5), Bent Shaft (AC-SM-BS5)  
2 Per box, can ship as single  
Packaging  
1
2
3
Frequency response is measured in half space and includes a low-frequency peak > + 3 dB.  
Continuous power rating, EIA-426-B test.  
2.83 Volts at a distance of 1 meter.  
SoundTube continually develops new product innovations and improvements. Updates to existing  
products without prior notice are an example of SoundTube’s drive for constant improvement.  
© 2006 SoundTube Entertainment. All rights reserved. PN TS-SM590 REV 03.03.06  
 
Surface-Mount Speaker  
SM590i  
Preliminary Technical Information for System Engineers  
Data Acquisition  
minum ball. For seismic and safety redun-  
dancy, a secondary aircraft cable shall  
be included and attached to the speaker  
chassis via ¼ - 20 bolt. The external wir-  
ing input connector shall be a 4-pin, 5 mm  
Euroblock for 8 Ohm or distributed sys-  
tems and shall accept from 10 – 22 gauge  
wire.  
Useable frequency response shall extend  
from 61 Hz – 22 kHz (-10 dB, half space,  
All performance data acquired at  
SoundTube’s Technical Measurement  
Center (TMC) are analyzed using a  
variety of standard measurement tech-  
niques, including Measured Length  
Sequence (MLS) and Time Delay  
Spectrometry (TDS). Performance,  
development and data acquisition tools  
include: Gold Line TEF 20, CLIO, LMS,  
LEAP, and proprietary modeling soft-  
ware. EASEdata are acquired through  
an automated TEF 20/Outline/EASE™  
interface.  
no external equalization). Measured  
sensitivity (2.83 Volt input, 1 meter) shall  
be at least 89.5 dB. The speaker shall  
have a nominal impedance of 8 Ohms  
and shall be available for 25/70.7/100  
Volt modes with voice coil/8 Ohm  
direct. The frequency-dividing network  
shall have a crossover frequency of 3  
kHz with a slope of 12 dB per octave  
(second order) for the high-pass filter.  
Rated power capacity shall be at least  
80 Watts continuous power (RMS), and  
conforms to EIA-426-B testing. Maxi-  
mum continuous output at 1 meter shall  
be 108.5 dB.  
The system shall be for indoor/outdoor  
applications and shall have a weather-  
resistant terminal boot covering all  
wire connectors. The enclosure shall be  
constructed of injection-molded, glass-  
reinforced ABS. The grille shall be con-  
structed of iridite-plated, powder-coated  
aluminum for lasting performance.  
EASE™ Data – 3-D polar plots.  
SoundTubeSPEC™ – Proprietary  
Overall cabinet dimensions shall be no  
more than 316.9 mm (12.48 in) in height by  
216.6 mm (8.53 in) in width by 305.1 mm  
(12.01 in) in depth (including SM bracket).  
The SM590i shall include mounting hard-  
ware, Euroblock connector & terminal  
weather boot.  
SoundTube speaker placement software.  
The low-frequency transducer shall  
have a polypropylene cone with butyl  
rubber surround. The high-frequency  
transducer shall be constructed of alu-  
minum material and incorporate a high-  
SPL horn.  
Architectural Specifications  
The loudspeaker shall consist of a 133  
mm (5.25 in) low-frequency transducer  
and a 25 mm (1 in) high-frequency  
transducer with a frequency-dividing  
network installed in a ported enclosure.  
The low-frequency voice coil diameter  
shall be 25 mm (1 in).  
Installation for the SM590i shall  
be by proprietary & corrosion-resis-  
tant captured-ball mounting system.  
SoundTube’s tool-free captured-ball  
mounting system incorporates a locking  
zinc alloy lever attaching to a cast-alu-  
The system shall be the SoundTube  
SM590i with mounting hardware for both  
low and high impedance applications.  
Performance specifications of a typi-  
cal production unit shall be as follows:  
Polar Plots  
250 Hz  
500 Hz  
1,000 Hz  
125 Hz  
4,000 Hz  
8,000 Hz  
10,000 Hz  
2,000 Hz  
Technical data, EASE plots, SoundTubeSPEC software & product downloads available at www.soundtube.com  
 
Surface-Mount Speaker  
SM590i  
Preliminary Technical Information for System Engineers  
SoundTube Entertainment  
Mechanical Drawings  
6430 North Business Park Loop  
Park City, Utah 84098  
216.6 mm (8.53 in)  
Phone 435.647.9555  
Fax  
435.647.9666  
Toll Free 800.647.TUBE  
All SoundTube products come  
with a 5-year limited warranty.  
316.9 mm (12.48 in)  
305.1 mm (12.01 in)  
Installation  
Unlocked  
Locked  
SoundTube’s SM590i is a surface-mount  
speaker designed to mount to a wall, pole,  
ceiling or other rigid structure. Vertical &  
horizontal pivoting offer unlimited aiming for  
indoor & outdoor applications.  
Optional Accessories  
U-Mount Bracket (AC-SM-UB5)  
Pole Mount Adaptor (AC-SM-PMA5)  
Bent Shaft (AC-SM-BS5)  
SoundTube Entertainment manufactures a complete line of speakers for:  
Open-Ceiling • In-Ceiling • Surface-Mount • Outdoor • Sound-Focusing  
All SoundTube products are designed and engineered in the USA.  
 

Peavey Cassette Player MCR 4A User Manual
Philips Cell Phone CT0199BLK User Manual
Philips Electric Shaver T 5000 User Manual
Philips Light Therapy Device HB554 User Manual
Philips Portable DVD Player PD9012 37 User Manual
Philips TV VCR Combo 20PV 220 User Manual
Porter Cable Automobile Parts PCG2200 User Manual
Poulan Snow Blower 403919 User Manual
Poulan Trimmer 530164253 User Manual
ProForm Treadmill 830QT User Manual