Philips Coffeemaker HD7830 User Manual

HD7830  
Coffee Machine  
2
6
3
7
4
8
5
9
1
h
i
A
B
J
F
g
K
10  
14  
18  
22  
11  
15  
19  
23  
12  
16  
20  
24  
13  
17  
21  
l
C
M
D
n
E
25  
O
P
Q
R
26  
30  
34  
27  
31  
35  
28  
32  
29  
33  
 
The light rings around the 1-cup button q and the 2-cup  
button qq indicate if there is still enough water left for  
brewing one or two cups of coffee. If there is not enough  
water left in the water reservoir for brewing two cups  
of coffee, the light ring around the 2-cup button qq will  
Be careful when you do this; make sure that the rubber  
sealing ring does not get stuck under the edge of the  
water distribution disc. If it does, the coffee machine will  
start leaking!  
Replacement  
All removable parts can be ordered from your Philips  
dealer or a Philips service centre.  
Environment  
Flushing  
not go on and this button cannot be operated.  
,
Do not throw the machine away with the normal  
household waste at the end of its life, but hand  
it in at an official collection point for recycling.  
By doing this you will help to preserve the  
environment (Fig. 35).  
\
,
-
The SENSE coffee machine starts brewing.  
The machine automatically supplies the selected  
amount of water.  
If you have not used the coffee machine for three days,  
you have to flush it with fresh water before you use it  
again.  
-
You can interrupt the brewing process at any time  
by pressing the on/off button 3. If you switch  
the machine back on after having interrupted the  
brewing process, the machine will not complete the  
interrupted brewing cycle.  
Flush the machine in the following way:  
1
Fill the water reservoir with cold water up to  
guarantee & service  
the MAX indication and put it back into the  
machine. (Fig. 3)  
If you need service or information or if you have a  
problem, please consult the worldwide guarantee leaflet  
or visit our website at www.philips.com.You can also  
Do not remove the water reservoir during a brewing  
cycle, as this will cause the machine to draw in air.When  
this happens, the next cup will only be partly filled.  
2
3
4
Put the 1-cup pod holder q or the 2-cup pod  
holder qq in the machine without pod(s). (Fig. 13) contact the Philips Customer Care Centre in your  
country; they will be happy to help you.  
Put a bowl (with a capacity of at least 1500 ml)  
The telephone number for the United Kingdom is: 0845-  
under the coffee spout to collect the water (Fig. 8).  
6010354.  
Press on/off button 3 (1) and subsequently press  
the 1-cup button q and the 2-cup button qq  
briefly at the same time (2). (Fig. 32)  
Note: If you only get a small quantity of coffee or no coffee  
at all out of the machine, you have not flushed the machine  
properly before first use.As a result, the boiler is not or not  
completely filled. Flush the machine properly (see chapter  
‘Preparing the machine for use’) before you brew another  
cup of coffee.  
You will find the telephone numbers for other countries  
in the worldwide guarantee leaflet. If there is no  
Customer Care Centre in your country, turn to your  
local Philips dealer or contact the Service Department of  
Philips Domestic Appliances and Personal Care BV.You  
will find their address and fax number in the worldwide  
guarantee leaflet.  
The machine fills itself with water from the water  
reservoir.While this happens, water comes out of  
the spout.When the flushing cycle is finished, the  
machine switches itself off. During the flushing cycle,  
the machine produces more noise than during a regular  
brewing cycle.  
11 Remove the coffee pod(s) after use by lifting the  
pod holder out of the machine and emptying it.  
Be careful when doing this, for there may still be some  
water/coffee on the coffee pod(s).  
\
The purchase of the Philips SENSEO coffee machine  
does not exhaust any of the rights of Sara Lee/Douwe  
Egberts or Philips under any of their patents nor does it  
confer upon the purchaser a licence under these patents.  
Descaling  
Tips  
,
By rinsing the pod holders, the coffee collector and  
the coffee spout regularly, you will make sure that  
the coffee always tastes optimally.  
Regular descaling will prolong the life of the coffee  
machine and will guarantee optimal brewing results for a  
long time.  
\
,
,
The SENSEO coffee will taste best if you stir it  
,
When you need to descale the machine, the  
descaling indication b appears on  
the display.This happens after 500 cups have  
been brewed.After another 8 cups, the descaling  
indication b disappears from the display  
(whether or not you have performed the descaling  
procedure). (Fig. 33)  
before drinking it.  
If you intend to make another cup of SENSEO  
\
coffee later, just leave the coffee machine switched  
on.The machine will automatically switch itself off  
after 1 hour. (Fig. 22)  
Cleaning  
1
Fill the water reservoir up to the MAX indication  
with descaler and water according to the  
instructions on the package of the descaler.Then  
put the water reservoir back into the coffee  
machine. (Fig. 3)  
\
Never immerse the SENSEO coffee machine in water.  
Never clean the machine by flushing it with the lid open.  
1
2
Always unplug the machine before cleaning it.  
Clean the outside of the machine with a moist  
cloth.  
Use a liquid descaler based on citric acid.  
2
Press the on/off button 3. (Fig. 9)  
3
4
Remove the coffee collector (Fig. 23).  
The machine is ready for use when the indicator light  
burns continuously.  
Take the coffee spout out of the machine by sliding  
it upwards (Fig. 24).  
3
Place the 1-cup pod holder q in the coffee  
machine, preferably with a used coffee pod in it.  
Close the lid and make sure it is properly locked.  
The coffee spout can only be taken out after the coffee  
collector has been removed.  
,
You can disassemble the coffee spout for more  
thorough cleaning! (Fig. 25)  
We advise you to put a used coffee pod in the pod  
holder when you descale the machine.This pod will serve  
as a ‘filter’ to prevent the sieve in the pod holder from  
getting clogged with scale residues.  
5
Clean the coffee spout, the coffee collector and  
the drip tray in hot water, if necessary with some  
washing-up liquid, or in the dishwasher (Fig. 26).  
4
Put a bowl with a capacity of at least 1500 ml  
under the spout openings to collect the mixture of  
descaler and water. (Fig. 8)  
6
Hold the cup tray in your hand while cleaning it  
with hot water, if necessary with some washing-up  
liquid (Fig. 27).  
5
Press the 2-cup button qq for 2 cups and let  
the machine operate. Repeat this until the water  
reservoir is empty. (Fig. 34)  
The cup tray can also be cleaned in the dishwasher.  
To clean the cup tray, always remove it from the  
machine, as it might prove sharp when handled  
incorrectly.Always handle it carefully.  
\
Never descale the SENSEO coffee machine with the  
lid open. Make sure the lid is properly locked.  
7
Clean the pod holders in hot water, if necessary  
with some washing-up liquid, or in the  
dishwasher. (Fig. 28)  
6
7
8
Repeat steps 1 to 5 with a new mixture of descaler  
and water.  
Empty the water reservoir to remove the mixture  
of descaler and water.  
Check if the sieve in the centre of the pod holder is  
clogged. If this is the case, unclog the sieve by rinsing the  
pod holder under a running tap. Use a washing-up brush  
to clean the sieve, if necessary.  
Rinse the machine at least 3 times by repeating  
steps 1 to 5, now using fresh water.  
Do not refill the water reservoir with used hot  
water.  
,
8
Clean the water reservoir in hot water, if necessary  
with some washing-up liquid. (Fig. 29)  
9
Clean the pod holder after descaling to prevent the  
sieve in the centre from getting clogged.  
Note: If you are using a washing-up brush, be careful not to  
damage the valve in the bottom of the water reservoir.  
Frost-free storage  
9
Do not use an object with sharp edges to clean the  
water inlet on the machine (Fig. 30).  
If the coffee machine has already been used and  
therefore has been flushed with water, it may only be  
used and stored in a frost-free place to prevent it from  
becoming damaged.  
10 Rinse the parts with fresh water after cleaning and  
put them back into the machine.  
11 Clean the water distribution disc with a moist  
cloth (Fig. 31).  
4222.001.9946.2  
3/4  
 
Problem  
Solution  
Problem  
Solution  
Troubleshooting  
If you have a problem, you may find the solution in the  
table below. If the table does not provide the solution  
to your problem or if you have a question, see chapter  
‘Guarantee & service’.  
\
the sealing ring is not stuck  
under the edge of the water  
distribution disc.  
The SENSEO  
Make sure that:  
coffee is not strong  
enough.  
the water drops on the  
worktop are not the result of  
placing or removing the water  
reservoir or removing used  
coffee pods;  
you have used the correct  
number of pods and have  
pressed the right button. Use  
1 pod in combination with the  
1-cup pod holder q and the  
1- cup button q.  
Problem  
Solution  
The indicator light  
continues to blink  
slowly.  
You have not yet flushed the  
coffee machine (see chapter  
‘Preparing the machine for use’).  
you do not remove the water  
reservoir when the coffee  
machine is heating up.This may  
cause water that normally ends  
up in the water reservoir to  
leak out of the machine.  
Use 2 pods in combination with  
the 2-cup pod holder qq and  
the 2-cup button qq.  
\
You have used the SENSEO  
coffee machine at an altitude  
higher than 2200 metres above  
sea level.This has caused the  
water in the machine to start  
boiling before it has reached  
the required temperature,  
which prevents the machine  
from functioning properly.  
Switch the machine off and no  
longer use it at altitudes higher  
than 2200 metres above sea  
level.  
the coffee pod(s) have been  
placed properly in the centre  
of the pod holder, to prevent  
water from escaping along the  
edge of the pod(s).When you  
are using two coffee pods on  
top of each other, make sure  
that the convex sides of both  
pods are pointing downwards  
and press the pods lightly into  
the pod holder;  
In all other cases, contact the  
Philips Customer Care Centre  
in your country.  
The coffee spout  
The coffee spout can only  
cannot be taken out be taken out after the coffee  
of the machine.  
collector has been removed.  
\
The SENSEO  
You have not yet flushed the  
coffee machine does coffee machine.When you use  
The lid cannot be  
opened.  
A vacuum may have  
temporarily formed under  
the lid.  
you have not used the same  
pod twice by accident;  
not produce coffee  
when used for the  
first time.  
the machine for the first time,  
you have to flush it before you  
can start brewing coffee (see  
chapter ‘Preparing for use’).  
Switch the machine off. Pull the  
lever up as far as it will go and  
wait 24 hours before opening  
the lid.You may need to use  
quite some force.  
the coffee in the pod is evenly  
distributed;  
The display doesn’t  
work when the  
You have not yet flushed the  
If you prefer a more robust  
coffee machine.The display  
\
flavour, SENSEO coffee pods  
machine is switched starts working after the  
on for the first time. machine has been flushed (see  
chapter ‘Preparing for use’).  
with a stronger blend are  
available.  
Make sure that the sieve in  
the centre of the pod holder  
is not clogged. If it is, unclog  
the sieve by holding the pod  
holder under a running tap.  
If necessary, you can use a  
washing-up brush or a pin to  
unclog the sieve.  
\
The SENSEO  
If you prefer a milder flavour,  
The indicator light  
continues to blink  
rapidly.  
Make sure that:  
\
coffee is too strong. SENSEO coffee pods with a  
milder blend are available.  
The coffee is not  
hot enough.  
Do not use cups that are too  
large, as they will cause the  
coffee to get cold more quickly.  
Make sure the cups have a  
capacity of at least 100 ml  
when brewing small cups f,  
150 ml when brewing medium  
cups g and 170ml when  
brewing large cups h.  
the water reservoir has been  
properly placed;  
If problems continue to occur,  
contact the Philips Customer  
Care Centre in your country.  
there is enough water in the  
water reservoir (i.e. above the  
q MIN level if you want to  
brew 1 cup);  
The coffee machine Perhaps the sieve in the centre  
produces less coffee of the pod holder is clogged. If  
the ambient temperature is  
than before.  
this is the case, unclog the sieve  
by rinsing the pod holder under  
a running tap. Use a washing-  
up brush to clean the sieve, if  
necessary.  
c
not lower than 10 C. If it is,  
the machine will not function  
properly.  
The preferred coffee Make sure that there is enough  
volume cannot be  
selected.  
water in the water reservoir.  
The 2-cup button  
qq cannot be  
operated.  
Make sure that there is enough  
water in the water reservoir  
for brewing 2 cups of coffee. If  
the light ring around the 2-cup  
button qq is out, there is not  
enough water in the water  
The coffee volume  
indication does  
not appear on the  
display and it is not  
possible to select a  
volume.  
Make sure that there is enough  
water in the water reservoir.  
Descale the machine (see  
chapter ‘Descaling’).  
\
The SENSEO  
You have not flushed the  
coffee machine  
machine properly before first  
use.As a result, the boiler is  
not or not completely filled.  
Flush the machine properly (see  
chapter ‘Preparing the machine  
for use’) before you brew  
another cup of coffee.  
reservoir for brewing 2 cups.  
brews only a small  
quantity of coffee  
or no coffee at all  
when it is used for  
the first time.  
Water leaks from  
the coffee machine.  
Make sure that:  
the lid is properly closed (the  
lever must be properly locked);  
The lid cannot be  
closed properly.  
Check if a used coffee pod  
is sticking to the water  
distribution disc. If this is the  
case, remove the used pod.  
the water reservoir has not  
been filled beyond the MAX  
level;  
the sieve in the centre of the  
pod holder is not clogged. If it  
is, unclog the sieve by holding  
the pod holder under a running  
tap. If necessary, you can use a  
washing-up brush or a pin to  
unclog the sieve;  
Check if you used the correct  
pod holder. Use 2 pods in  
combination with the deeper  
2-cup pod holder qq.  
Use 1 pod in combination with  
the 1-cup pod holder q.  
The machine has  
been stored in a  
room that was not  
frost-free.  
Contact the Philips Customer  
Care Centre in your country.  
the coffee pod has been put  
properly in the centre of the  
pod holder;  
4222.001.9946.2  
4/4  
 

Pelco Camcorder IH8 User Manual
Perreaux MP3 Player Accessories 4004A User Manual
Philips CD Player AZ5160 98 User Manual
Philips Flat Panel Television 14GR1229 User Manual
Philips Styling Iron GC2030 User Manual
Philips Switch SWV3570 User Manual
Polaris Offroad Vehicle 700 Dragon RMK User Manual
Polycom Cordless Telephone Pro SE 220 User Manual
Pride Mobility High Chair Quantum 1121 User Manual
PYLE Audio DJ Equipment PWMA 160 User Manual