Philips Satellite TV System SLV5405 User Manual

Wireless TV Link  
SLV5405  
User Manual  
 
EN  
Overview  
Control and display elements  
A Receiver  
1
2
On/off switch  
Power light  
>
>
>
red: standby  
green: on  
blinking: remote control signalling  
3
Source selector buttons (+/-)  
>
in combination with the SLV5400 transmitter  
4
5
6
7
8
Integrated remote control blaster light  
Antenna  
Wireless channel selection switch  
SCART port for TV2  
Power input connector (DC 12V)  
4
 
   
EN  
Your Wireless TV Link  
You can say good-bye to wires. With your Wireless TV  
Link receiver you can now wirelessly connect a third TV  
and choose between four devices to watch on your third  
TV.  
Safety  
Read the instructions in this manual carefully before  
you connect, install and use the product.  
Keep this manual for future reference.  
The product is for indoor use only.  
Do not use the product close to water.  
Do not expose the product to extreme heat.  
In case of technical difficulties, do not open the  
product. Bring it to your Philips dealer.  
Do not cover the product.  
Connect the power adapters only to a  
220-240 V AC/50 Hz power supply.  
The product can cause interference to other  
equipment. Check if any equipment near the product  
can be affected before you start using it.  
5
 
   
EN  
Installation  
For basic installation, see  
the quick start guide that  
came with your Wireless  
TV Link.  
Rem ove interference on TV3  
L
1
2
Find the CHANNEL switch on the transmitter.  
DC 12V  
Check the setting of the CHANNEL switch.  
Channel  
1 2 3 4  
R
3
4
Find the CHANNEL switch on the receiver (A).  
Set the CHANNEL switch to the same number as  
on the transmitter.  
CHANNEL  
1
2
3
4
Make sure to set the CHANNEL  
switch on both the original and the new  
receiver.  
Operation  
Enjoy your Wireless TV Link  
For basic installation, see  
the quick start guide that  
came with your Wireless  
TV Link.  
6
 
       
EN  
Operation  
W atch a cable TV program on TV3  
Your VCR or DVD recorder needs to  
be connected to the transmitter (A) of  
the Wireless TV Link and connected to  
the Cable-TV signal.  
1
2
3
Switch on the transmitter.  
Switch on the VCR or DVD recorder.  
Take the remote control of the VCR or DVD  
recorder with you.  
SELECT  
STANDBY  
SLVELESSTV LINK TRANSMITTER  
4
Go to TV3.  
5
6
Switch on TV3.  
Switch on the receiver (A).  
WIRELESS TV LINK RECEIVER  
7
8
Press + or - on the receiver (A) to select the VCR or  
DVD recorder;  
or: press 4 on the remote control.  
Select the channel on the VCR or DVD recorder  
with its remote control.  
Turn off the auto standby mode when  
you use the VCR or DVD recorder to  
watch a cable tv program. Refer to the  
user manual of the VCR or DVD  
recorder.  
If the VCR or DVD recorder records a  
television program, you watch the  
recorded channel.  
7
 
EN  
Troubleshooting  
Problem  
Tip  
No image or wrong Make sure SCART cables are  
firmly inserted.  
image on TV3  
Make sure the receiver (A) is  
connected to TV3.  
Make sure both receiver (A) and  
transmitter are switched on.  
Make sure the video source is  
switched on.  
Make sure the correct SCART  
input on TV3 is selected.  
Select the correct video source  
with +/- on the receiver (A).  
>
In combination with the  
SLV5400 transmitter.  
If the video source gives proper  
image on TV1:  
Make sure the video source gives  
video signal in CVBS mode. See  
its user manual  
Change the wireless channel that  
is used for communication. See  
The receiver (A) is out of range  
of the transmitter. The number  
of walls and ceilings in between  
the receiver (A) and transmitter  
restrict the distance.  
Interference in the Slightly change the position of the  
receiver (A) or the transmitter.  
Change the wireless channel that  
is used for communication. See  
The receiver (A) is out of range  
of the transmitter. The number  
of walls and ceilings in between  
the receiver (A) and transmitter  
restrict the distance.  
image on TV3  
8
 
 
EN  
Troubleshooting  
Problem  
Tip  
The video sources Point the remote control directly  
to the receiver (A).  
do not respond to  
the remote  
control commands  
from TV3  
Replace the batteries of the  
remote controls with new ones.  
Install the remote control blaster  
cord. See the user manual of the  
Wireless TV Link.  
The maximum operating distance  
of the remote control is 5 m.  
The image of the Turn off the auto standby mode  
of the video source. See its user  
manual.  
video source dis-  
appears on TV3  
Follow the instructions to recon-  
nect the video sources. See the  
quick start guide.  
Buzzing sound  
when you use the  
remote control.  
Slightly change the position of the  
receiver or the transmitter until  
the buzzing sound stops.  
Sometimes it is not possible to  
solve the problem.  
Black and white  
image with S-VHS  
VCR.  
Check if the SCART connector of  
the S-VHS VCR gives signal in  
CVBS. See its user manual.  
9
 
EN  
Information  
Health and safety  
The product transmits and receives radio waves when it  
is switched on. The product complies with the standards  
that are defined for it.  
The quality of the image can be influenced by the use of  
microwave ovens. Other wireless systems (Bluetooth,  
wireless networks etc.) can also have influence on the  
quality of the image.  
The product is based on RF technology. Therefore the  
product can suffer from the same kinds of interference  
as GSMs, portable radios and other RF-based products.  
Maintenance and service  
If your product is defective and needs repair, but your  
warranty period has expired, you can consult our  
specialists (see the rear page)  
Recycling and disposal  
All redundant packaging material has been omitted. Your  
set consists of materials that can be recycled if  
disassembled by a specialized company. Please observe  
the local regulations regarding the disposal of packaging  
materials, batteries and old equipment.  
Disposal of your old product  
Your product is designed and manufactured with high  
quality materials and components, which can be recycled  
and reused.  
When this crossed-out wheeled bin symbol is attached  
to a product it means the product is covered by the  
European Directive 2002/96/EC.  
Please inform yourself about the local separate collection  
system for electrical and electronic products.  
Please act according to your local rules and do not  
dispose of your old products with your normal  
household waste. The correct disposal of your old  
product will help prevent potential negative  
consequences for the environment and human health.  
10  
 
       
EN  
Information  
Warranty  
O ne year lim ited warranty  
For 12 month from the date of purchase the  
manufacturer repairs or replaces any faulty product free  
of charge, subject to proof of purchase, provided the  
fault has not been caused by improper handling or use,  
and provided the product has not been damaged,  
whether as a result of an accident or of repair by others  
than the manufacturer.  
Glossary  
CVBS  
Video standard for showing colors on a  
TV.  
Easylink  
Gives a VCR or DVD recorder the  
possibility to automatically take over the  
preset programming of the TV.  
RF  
Technology based on radio frequency,  
technology used for wireless connections.  
SCART  
Single connector to easily connect audio  
and video equipment.  
11  
 
   
AQ95-56F-614KR  
(report No.)  
EC DECLARATION OF CONFORMITY  
We , Philips Consumer Electronics B.V., P&A CC: Building SBP6  
(manufacturer's name)  
P.O.Box 80002, 5600 JB Eindhoven, The Netherlands  
(manufacturer's address)  
declare under our responsibility that the electrical product:  
Philips  
(name)  
SLV5405 -/00 -/05 ( Rx: SLV5405 -/00-R )  
(type or model)  
Wireless TV link receiver  
(product description)  
to which this declaration relates is in conformity with the following standards:  
EN 300 440 part 1&2, (2001-9).  
EN 300 220-1 v1.3.1  
EN 301 489-1 V1.2.1  
EN 301 489-3 V1.2.1  
EN 60065:1998 ed.6  
EN 60950:2000  
(title and/or number and date of issue of the standards)  
following the provisions of 1999/5/EC ( R&TTE Directive)  
and is produced by a manufacturing organisation on ISO 9000 level.  
Eindhoven, 27/06/2005  
K.Rysman  
Approbation manager  
(signature, name and function)  
(place, date)  
 
Need help?  
Troubleshooting  
See page 8  
Helpline  
België/Belgique/Belgien 070 222 303 (0.17)  
Danmark  
Deutschland  
España  
France  
ÅëëÜäá  
3525 8759  
0900 1101211 (0.12)  
902 888 784 (0.15)  
08 9165 0005 (0.23)  
0 0800 3122 1280  
01 764 0292  
Ireland  
Italia  
899 23 45 06 (0.25)  
Luxemburg/Luxembourg 40 6661 6544  
Nederland  
Norge  
Österreich  
Portugal  
0900 8407 (0.20)  
2270 8111  
0900 060 827 (0.20)  
2 1359 1442  
Schweiz/Suisse/Svizzera 0900 001 600  
Suomi  
Sverige  
0600 412 001  
08 5792 9100  
UK (United Kingdom)  
0906 1010 016 (£ 0.15)  
Specifcations are subject to change without notice.  
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.  
2005 © Koninklijke Philips Electronics N.V. All rights reserved.  
DFU-SLV5405-AEN-V1.0  
 

Pelco Pacemaker C2907M QS User Manual
Perreaux Home Theater System GS2002 User Manual
Philips Cordless Telephone DECT5251B User Manual
Philips DVR DVR I Series User Manual
Philips Iron GC3230 User Manual
Philips Portable Speaker SBA1600 00 User Manual
Philips Telephone Xalio 300 User Manual
Polk Audio Speaker 303 User Manual
Poulan Tiller 159399 User Manual
ProForm Home Gym PFCCEX97573 User Manual