Philips Speaker HTL3120 User Manual

Always there to help you  
Register your product and get support at  
HTL3120  
Question?  
Contact  
Philips  
User manual  
 
Contents  
1 Important  
Safety  
2
2
3
3
3
3
4
Mains fuse  
Care for your product  
Care of the environment  
Compliance  
Help and support  
2 Your SoundBar  
Main unit  
4
4
4
6
Remote control  
Connectors  
3 Connect and set up  
Connect toTV  
7
7
7
Connect digital devices through HDMI  
Connect audio fromTV and other  
devices  
8
8
Set up EasyLink (HDMI-CEC control)  
4 Use your SoundBar  
Adjust the volume  
Choose your sound  
MP3 player  
9
9
9
10  
10  
11  
11  
12  
USB storage devices  
Play audio through Bluetooth  
Auto standby  
Apply factory settings  
5 Wall mount  
12  
13  
14  
6
Product specifications  
7 Troubleshooting  
EN  
1
 
product and wait until its temperature  
matches room temperature before  
connecting it to the power outlet.  
Parts of this product can be made of  
glass. Handle with care to avoid injury and  
damage.  
1 Important  
Read and understand all instructions before you  
use your product. If damage is caused by failure  
to follow instructions, the warranty does not  
apply.  
Risk of overheating!  
Never install this product in a confined  
space.Always leave a space of at least four  
inches around the product for ventilation.  
Ensure curtains or other objects never  
cover the ventilation slots on the product.  
Safety  
Risk of contamination!  
Risk of electric shock or fire!  
Do not mix batteries (old and new or  
carbon and alkaine, etc.).  
Never expose the product and accessories  
to rain or water. Never place liquid  
containers, such as vases, near the product.  
If liquids are spilt on or into the product,  
disconnect it from the power outlet  
immediately. Contact Philips Consumer  
Care to have the product checked before  
use.  
Danger of explosion if batteries are  
incorrectly replaced. Replace only with the  
same or equivalent type.  
Remove batteries if they are exhausted or  
if the remote control is not to be used for  
a long time.  
Batteries contain chemical substances, they  
should be disposed of properly.  
Never place the product and accessories  
near naked flames or other heat sources,  
including direct sunlight.  
Risk of swallowing batteries!  
The product/remote control may contain  
a coin/button type battery, which can be  
swallowed. Keep the battery out of reach  
of children at all times! If swallowed, the  
battery can cause serious injury or death.  
Severe internal burns can occur within two  
hours of ingestion.  
Never insert objects into the ventilation  
slots or other openings on the product.  
Where the mains plug or an appliance  
coupler is used as the disconnect device,  
the disconnect device shall remain readily  
operable.  
Disconnect the product from the power  
outlet before lightning storms.  
When you disconnect the power cord,  
always pull the plug, never the cable.  
If you suspect that a battery has been  
swallowed or placed inside any part of the  
body, seek immediate medical attention.  
When you change the batteries, always  
keep all new and used batteries out of  
reach of children. Ensure that the battery  
compartment is completely secure after  
you replace the battery.  
Risk of short circuit or fire!  
Before you connect the product to the  
power outlet, ensure that the power  
voltage matches the value printed on the  
back or bottom of the product. Never  
connect the product to the power outlet if  
the voltage is different.  
If the battery compartment cannot be  
completely secured, discontinue use of the  
product. Keep out of reach of children and  
contact the manufacturer.  
Risk of injury or damage to the SoundBar!  
Never place the product or any objects  
on power cords or on other electrical  
equipment.  
If the product is transported in  
temperatures below 5°C, unpack the  
2
EN  
 
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product  
is covered by the European Directive 2002/96/  
EC. Please inform yourself about the local  
separate collection system for electrical and  
electronic products.  
This is CLASS II apparatus with double  
insulation, and no protective earth provided.  
Mains fuse  
Please act according to your local rules and  
do not dispose of your old products with your  
normal household waste.  
Correct disposal of your old product helps to  
prevent potential negative consequences for the  
environment and human health.  
This information applies only to products with a  
UK mains plug.  
This product is fitted with an approved molded  
plug. If you replace the fuse, use one with:  
the ratings shown on the plug,  
a BS 1362 approval, and  
the ASTA approval mark.  
Contact your dealer if you are not sure about  
what type of fuse to use.  
Your product contains batteries covered by the  
European Directive 2006/66/EC, which cannot  
be disposed with normal household waste.  
Please inform yourself about the local rules  
on separate collection of batteries because  
correct disposal helps to prevent negative  
consequences for the environmental and  
human health.  
Caution:To conform with the EMC directive  
(2004/108/EC), do not detach the plug from  
the power cord.  
Copyright in the U.K.  
Recording and playback of material may  
require consent. See Copyright Act 1956  
andThe Performer’s Protection Acts 1958  
to 1972.  
Compliance  
Care for your product  
Use only microfiber cloth to clean the product.  
1797  
Care of the environment  
This product complies with the radio  
interference requirements of the European  
Community.  
Hereby, Philips Consumer Lifestyle, declares that  
this product is in compliance with the essential  
requirements and other relevant provisions of  
Directive 1999/5/EC.  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
A copy of the EC declaration of Conformity  
is available in the Portable Document Format  
(PDF) version of the user manual at www.  
philips.com/support.  
EN  
3
 
2 Your SoundBar  
Help and support  
Philips provides extensive online support.Visit  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from  
the support that Philips offers, register your  
download the user manual and the quick  
start guide  
watch video tutorials (available only for  
selected models)  
find answers to frequently answered  
questions (FAQs)  
Main unit  
email us a question  
chat with our support representative.  
This section includes an overview of the main  
unit.  
Follow the instructions on the website to select  
your language, and then enter your product  
model number.  
Alternatively, you can contact Philips Consumer  
Care in your country. Before you contact  
Philips, note down the model number and  
serial number of your product.You can find this  
information on the back or bottom of your  
product.  
a b c  
d
a
(Standby-On/Standby indicator)  
Switch the SoundBar on or to standby.  
When the SoundBar is in standby, the  
standby indicator turns red.  
b VOLUME +-  
Increase or decrease volume.  
c SOURCE  
Select an input source or Bluetooth mode  
for the SoundBar.  
d Display panel  
Remote control  
This section includes an overview of the  
remote control.  
4
EN  
 
c HDMI 1  
Switch your source to the HDMI IN 1  
connection.  
1
2
d OPTICAL  
Switch your audio source to the optical  
connection.  
3
4
23  
e AUDIO-IN  
Switch your audio source to the MP3  
connection (3.5mm jack).  
5
6
22  
21  
20  
19  
f
g
Bluetooth  
Switch to Bluetooth mode.  
(Repeat)  
7
Select or turn off repeat/shuffle mode in  
USB mode.  
8
h
/
(Previous/Next)  
Skip to the previous or next track in USB  
mode and Bluetooth mode (only for  
AVRCP-supported Bluetooth devices).  
18  
17  
9
16  
15  
14  
13  
12  
i SOUND  
Select a sound mode.  
j DIM  
Set the brightness of SoundBar display  
panel.  
10  
11  
k AUTOVOL  
Turn auto volume on or off.  
l NIGHT MODE  
Turn night mode on or off.  
m BASS +/-  
Increase or decrease bass.  
n TREBLE +/-  
a
(Standby-On)  
Increase or decrease treble.  
Switch the SoundBar on or to standby.  
When EasyLink is enabled, press  
and hold for at least three seconds  
to switch all connected HDMI CEC  
compliant devices to standby.  
o AUDIO SYNC +/-  
Increase or decrease audio delay.  
p +/- (Volume)  
Increase or decrease volume.  
b HDMI ARC  
Switch your source to HDMI ARC  
q
(Mute)  
Mute or restore volume.  
connection. If the connectedTV is not  
HDMI ARC compliant or an unsupported  
audio format is detected,ARC” on the  
display panel blinks.  
r SURR  
Select surround or stereo sound.  
EN  
5
 
In HDMI in mode (connected via  
HDMI IN 1 or HDMI IN 2), press and  
hold to switch audio output from the  
Soundbar speaker orTV speaker.  
b
(USB)  
Audio input from a USB storage device.  
Rear connectors  
s
(Play/Pause)  
Start, pause or resume play in USB  
mode and Bluetooth mode (only for  
AVRCP-supported Bluetooth devices).  
Press and hold to stop play in USB  
mode.  
t USB  
Switch to USB mode.  
u AUX  
Switch your audio source to the AUX  
connection.  
v COAX  
Switch your audio source to the coaxial  
connection.  
a AUDIO IN-AUX  
w HDMI 2  
Connect to an analog audio output on the  
TV or an analog device.  
Switch your source to the HDMI IN 2  
connection.  
b DIGITAL IN-OPTICAL  
Connect to an optical audio output on the  
TV or a digital device.  
Connectors  
c DIGITAL IN-COAXIAL  
Connect to a coaxial audio output on the  
TV or a digital device.  
This section includes an overview of the  
connectors available on your SoundBar.  
d TOTV-HDMI OUT (ARC)  
Connect to the HDMI input on theTV.  
Side connectors  
e HDMI IN 1 / HDMI IN 2  
Connect to the HDMI output on a digital  
device.  
f AC MAINS~  
Connect to the power supply.  
a AUDIO-IN  
Audio input from an MP3 player (3.5mm  
jack).  
6
EN  
 
SoundBar to the HDMI ARC connector  
on theTV.  
3 Connect and set  
up  
The HDMI ARC connector on theTV  
might be labeled differently. For details,  
see theTV user manual.  
2 On yourTV, turn on HDMI-CEC  
operations. For details, see theTV user  
manual.  
This section helps you connect your SoundBar  
to aTV and other devices, and then set it up.  
For information about the basic connections of  
your SoundBar and accessories, see the quick  
start guide.  
Note  
SoundBar. (see 'Connect audio fromTV and other  
devices' on page 8)  
If yourTV has a DVI connector, you can use an HDMI/  
DVI adapter to connect toTV. However, some of the  
features may not be available.  
Note  
For identification and supply ratings, see the type plate  
at the back or bottom of the product.  
Before you make or change any connections, make sure  
that all devices are disconnected from the power outlet.  
Connect digital devices  
through HDMI  
Connect toTV  
Connect your SoundBar to aTV.You can listen  
to audio fromTV programs through your  
SoundBar. Use the best quality connection  
available on your SoundBar andTV.  
Connect a digital device such as a set-top box,  
DVD/Blu-ray player, or games console to your  
SoundBar through a single HDMI connection.  
When you connect the devices in this way and  
play a file or game, the  
Connect toTV through HDMI (ARC)  
video is automatically displayed on your  
TV, and  
Your SoundBar supports HDMI version with  
Audio Return Channel (ARC). If yourTV is  
HDMI ARC compliant, you can hear theTV  
audio through your SoundBar by using a single  
HDMI cable.  
audio is automatically played on your  
SoundBar.  
1 Using a High Speed HDMI cable, connect  
the HDMI OUT connector on your digital  
device to the HDMI IN 1/2 on your  
SoundBar.  
TV  
2 Connect your SoundBar toTV through  
HDMI OUT (ARC).  
If theTV is not HDMI CEC compliant,  
select the correct video input on your  
TV.  
3 On the connected device, turn on HDMI-  
CEC operations. For details, see the user  
manual of the device.  
1 Using a High Speed HDMI cable, connect  
the HDMI OUT (ARC) connector on your  
EN  
7
 
 
Option 2: Connect audio through a  
digital coaxial cable  
Connect audio fromTV and  
other devices  
Good quality audio  
Play audio fromTV or other devices through  
your Soundbar speakers.  
Use the best quality connection available on  
yourTV, Soundbar, and other devices.  
Note  
'Connect toTV through HDMI (ARC)' on page 7)  
1 Using a coaxial cable, connect the  
COAXIAL connector on your SoundBar  
to the COAXIAL/DIGITAL OUT  
Option 1: Connect audio through a  
digital optical cable  
connector on theTV or other device.  
The digital coaxial connector might be  
labeled DIGITAL AUDIO OUT.  
Best quality audio  
Option 3: Connect audio through  
analog audio cables  
TV  
Basic quality audio  
1 Using an analog cable, connect the AUX  
connectors on your SoundBar to the  
AUDIO OUT connectors on theTV or  
other device.  
1 Using an optical cable, connect the  
OPTICAL connector on your SoundBar to  
the OPTICAL OUT connector on theTV  
or other device.  
DVD  
The digital optical connector might be  
labeled SPDIF or SPDIF OUT.  
Set up EasyLink (HDMI-CEC  
control)  
Your SoundBar supports Philips EasyLink, which  
uses the HDMI-CEC (Consumer Electronics  
8
EN  
 
 
Control) protocol. EasyLink-compliant devices  
that are connected through HDMI can be  
controlled by a single remote control.  
4 Use your  
SoundBar  
Note  
This section helps you use the SoundBar to play  
audio from connected devices.  
Depending on the manufacturer, HDMI-CEC is known  
by many names. For information on your device, see  
the user manual of the device.  
Philips does not guarantee 100% interoperability with  
Before you start  
all HDMI-CEC devices.  
Make the necessary connections described  
in the quick start guide and the user  
manual.  
Before you start  
Switch the SoundBar to the correct source  
for other devices.  
Connect your SoundBar to the HDMI-  
CEC compliant device through HDMI  
connection.  
Make the necessary connections described  
in the quick start guide, and then select the  
correct audio source for the connected  
device.  
On yourTV and other connected devices,  
turn on HDMI-CEC control. For details, see  
the user manual of theTV or other devices.  
Adjust the volume  
1 Press +/- (Volume) to increase or decrease  
a volume level.  
To mute sound, press (Mute).  
To restore the sound, press (Mute)  
again or press +/- (Volume).  
EasyLink controls  
With EasyLink, you can control your SoundBar,  
TV, and other connected HDMI-CEC compliant  
devices with a single remote control.  
Choose your sound  
This section helps you choose the ideal sound  
for your video or music.  
One-touch standby: If one-touch standby  
is enabled, your SoundBar can switch to  
standby with the remote control of theTV  
or other HDMI-CEC devices.  
Sound mode  
Select predefined sound modes to suit your  
video or music.  
1 Press SOUND to select a sound option  
from the display panel.  
AUtO:Automatically select a sound  
setting based on the sound stream.  
OFF: Experience the original sound of  
your movies and music, without added  
sound effects.  
POWEr: Enjoy thrilling arcade sounds,  
ideal for action-packed videos and loud  
parties.  
EN  
9
 
HIGH: Spice up your dull movies and  
music with added sound effects.  
CLEAr: Hear every detail in your music  
and clear voices in your movies.  
dEEP: Experience spoken words and  
music vocals in comfort.  
Night mode  
For quiet listening, decrease the volume of loud  
sounds when audio is played. Night mode is  
only available for Dolby Digital soundtracks.  
1 Press NIGHT MODE to turn night mode  
OWN: Personalize the sound based on  
your preferences.  
on or off.  
Note  
Surround sound mode  
If auto volume is set to turned on, you cannot enable  
the night mode.  
Experience an immersive audio experience with  
surround sound modes.  
1 Press SURR to select a sound option from  
the display panel.  
AUtO: Intelligently select the best  
surround sound mode based on the  
media played.  
OFF:Two-channel stereo sound. Ideal  
for listening to music.  
MP3 player  
Connect your MP3 player to play your audio  
files or music.  
What you need  
SURR: Multi-channel surround output.  
An MP3 player.  
A 3.5mm stereo audio cable.  
Equalizer  
1 Using the 3.5mm stereo audio cable,  
connect the MP3 player to the AUDIO-IN  
connector on your SoundBar.  
Change the high frequency (treble) and low  
frequency (bass) settings of the SoundBar.  
1 Press TREBLE +/- or BASS +/- to change  
2 Press AUDIO-IN on the remote control.  
the frequency.  
3 Press the buttons on the MP3 player to  
select and play audio files or music.  
Auto volume  
Turn the auto volume on to keep the volume  
constant when you switch to a different source.  
USB storage devices  
1 Press AUTOVOL to turn auto volume on  
Enjoy audio on a USB storage device, such as an  
MP3 player and USB flash memory, etc.  
or off.  
What you need  
Synchronize picture and sound  
A USB storage device that is formatted  
for FAT file systems, and complies with the  
Mass Storage Class.  
If the audio and video are not synchronized,  
delay the audio to match the video.  
An MP3 or WMA file on a USB storage  
device  
1 Press AUDIO SYNC +/- to synchronize  
the audio with the video.  
1 Connect a USB storage device to the  
SoundBar.  
2 Press USB on the remote control.  
10 EN  
 
3 Use the remote control to control play.  
user manual of the Bluetooth device on  
how to enable Bluetooth).  
» During connection, bt on the display  
panel blinks.  
Button  
Action  
Start, pause or resume play.  
Press and hold to stop play.  
Skip to the previous or next track.  
Select or turn off repeat/shuffle  
mode.  
3 Wait until you hear a beep sound from the  
SoundBar.  
/
» When the Bluetooth connection  
succeeds, bt is displayed on the display  
panel without blinking.  
(Repeat)  
» If the connection fails, bt on the display  
Note  
panel blinks continuously.  
This product may not be compatible with certain types  
of USB storage device.  
If you use a USB extension cable, USB HUB, or USB  
multi-reader, the USB storage device may not be  
recognized.  
Digital camera PTP protocols are not supported.  
Do not remove the USB storage device while it is  
being read.  
4
Select and play audio files or music on  
your Bluetooth device.  
During play, if a call is coming, music  
play is paused. Play resumes when the  
call ends.  
If your Bluetooth device supports  
AVRCP profile, on the remote control  
DRM-protected music files (MP3,WMA) are not  
supported.  
Support a USB port: 5V , 1A.  
you can press  
/
to skip to a track,  
or press  
to pause/resume play.  
5 To exit Bluetooth, select other source.  
When your switch back to Bluetooth  
mode, Bluetooth connection remains  
active.  
Play audio through Bluetooth  
Through Bluetooth, connect the SoundBar with  
your Bluetooth device (such as an iPad, iPhone,  
iPod touch,Android phone, or laptop), and then  
you can listen to the audio files stored on the  
device through your SoundBar speakers.  
What you need  
Note  
The music streaming may be interrupted by obstacles  
between the device and SoundBar, such as wall, metallic  
casing that covers the device, or other devices nearby  
that operate in the same frequency.  
If you want to connect your SoundBar with another  
Bluetooth device, press and hold Bluetooth on the  
remote control to disconnect the currently connected  
Bluetooth device.  
A Bluetooth device which supports  
Bluetooth profile A2DP, AVRCP and with  
Bluetooth version as 3.0 + EDR.  
Philips does not guarantee 100% compatibility with all  
Bluetooth devices.  
The operational range between the  
SoundBar and a Bluetooth device is  
approximately 10 meters (30 feet).  
1 Press Bluetooth on the remote control  
to switch the SoundBar to Bluetooth  
mode.  
Auto standby  
» bt is displayed on the display panel,  
blinking.  
When playing media from a connected device,  
the SoundBar automatically switches to standby  
if:  
2 On the Bluetooth device, switch on  
Bluetooth, search for and select Philips  
HTL3120 to start connection (see the  
no button is pressed for 29 minutes, and  
EN 11  
 
no audio/video play from a connected  
device.  
5 Wall mount  
Note  
Apply factory settings  
Koninklijke Philips Electronics N.V. bears no  
responsibility for improper wall mounting that results  
in accident, injury or damage. If you have any query,  
contact Philips Consumer Care in your country.  
Before wall mounting, make sure the wall can support  
the weight of your SoundBar.  
Before wall mount, you need not remove the three  
rubber feet at the bottom of the soundbar, otherwise  
the rubber feet cannot be fixed back.  
You can reset your SoundBar to the default  
settings programmed at the factory.  
1 In AUX mode, within three seconds, press  
VOL-, BASS-,and Treble-.  
» When the factory settings restore is  
complete, the SoundBar automatically  
switches off and restarts.  
Screw length/diameter  
Depending on the type of wall mounting your  
SoundBar, make sure that you use screws of a  
suitable length and diameter.  
3.5-4mm  
4mm  
> 25mm  
For information about how to wall mount your  
SoundBar, see the quick start guide.  
12 EN  
 
WMA:V7,V8,V9  
6 Product  
specifications  
Bluetooth  
Bluetooth profiles:A2DP, AVRCP  
Bluetooth version: 3.0 + EDR  
Note  
Main unit  
Specifications and design are subject to change without  
Power supply: 110-240V~, 50/60 Hz  
notice.  
Power consumption: 25 W  
Standby power consumption: ≤ 0.5 W  
Speaker impedance: 8 ohm  
Speaker drivers: 4 x 3" woofer  
Dimensions (WxHxD): 995 x 94 x 102.5  
mm  
Amplifier  
Total output power: 120W RMS (+/- 0.5  
dB, 30%THD) / 96W RMS (+/- 0.5 dB,  
10%THD)  
Weight: 3.5 kg  
Frequency response: 20 Hz-20 kHz /  
±3 dB  
Signal-to-noise ratio: > 65 dB (CCIR) /  
(A-weighted)  
Remote control batteries  
2 x AAA-R03-1.5V  
Input sensitivity:  
AUX: 750 mV  
AUDIO-IN: 400 mV  
Audio  
S/PDIF Digital audio input:  
Coaxial: IEC 60958-3  
Optical:TOSLINK  
USB  
Compatibility: Hi-Speed USB (2.0)  
Class support: USB Mass Storage Class  
(MSC)  
File system: FAT16, FAT32  
Supports MP3 and WMA file formats  
Sampling frequency:  
MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz, 22  
kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz  
WMA: 44.1 kHz, 48 kHz  
Constant bit rate:  
MP3: 8 kbps-320 kbps  
WMA: 32 kbps-192 kbps  
Version:  
EN 13  
 
Bluetooth  
7 Troubleshooting  
A device cannot connect with the SoundBar.  
The device does not support the  
compatible profiles required for the  
SoundBar.  
Warning  
You have not enabled the Bluetooth  
function of the device. See the user manual  
of the device on how to enable the  
function.  
The device is not correctly connected.  
Connect the device correctly.  
The SoundBar is already connected with  
another Bluetooth device. Disconnect the  
connected device, then try again.  
Risk of electric shock. Never remove the casing of the  
product.  
To keep the warranty valid, never try to repair  
the product yourself.  
If you have problems using this product, check  
the following points before you request service.  
If you still have a problem, get support at www.  
philips.com/support.  
Quality of audio play from a connected  
Bluetooth device is poor.  
Main unit  
The Bluetooth reception is poor. Move the  
device closer to the SoundBar, or remove  
any obstacle between the device and the  
SoundBar.  
The buttons on the SoundBar do not work.  
Disconnect the SoundBar from the power  
supply for a few minutes, then reconnect.  
The connected Bluetooth device connects and  
disconnects constantly.  
Sound  
The Bluetooth reception is poor. Move the  
device closer to the SoundBar, or remove  
any obstacle between the device and the  
SoundBar.  
No sound from SoundBar speakers.  
Connect the audio cable from your  
SoundBar to yourTV or other devices.  
However, you do not need a separate  
audio connection when:  
Turn off Wi-Fi function on the Bluetooth  
device to avoid interference.  
For some Bluetooth, the Bluetooth  
connection can be deactivated  
the SoundBar andTV are connected  
through HDMI ARC connection, or  
a device is connected to the HDMI IN  
connector on your SoundBar.  
automatically to save power.This does not  
indicate any malfunction of the SoundBar.  
Reset your SoundBar to its factory settings.  
On the remote control, select the correct  
audio input.  
Make sure that the SoundBar is not muted.  
Distorted sound or echo.  
If you play audio from theTV through the  
SoundBar, make sure that theTV is muted.  
Audio and video are not synchronized.  
Press AUDIO SYNC +/- to synchronize  
the audio with the video.  
14 EN  
 
Philips Consumer Lifestyle B.V.  
HK-1303- HTL3120  
.................................................................  
(Document No. / Numéro du document)  
2013/01  
..............................................................................................  
(Year, Month (yyyy/mm) in which the CE mark is affixed /  
Année/mois (aaaa/mm) au cours de laquelle le marquage  
CE a été apposé)  
EUROPEAN DECLARATION OF CONFORMITY  
(DECLARATION DE CONFORMITE CE)  
We / Nous, PHILIPS CONSUMER LIFESTYLE B.V.  
(Company name / Nom de l’entreprise)  
TUSSENDIEPEN 4, 9206 AD DRACHTEN, THE NETHERLANDS  
(address / adresse)  
declare under our responsibility that the product(s):  
(déclarons sous notre propre responsabilité que le(s) produit(s))  
Philips  
HTL3120/12  
.............................................................................  
(brand name, nom de la marque)  
...........................................................................  
(Type version or model, référence ou modèle)  
Sound Speaker  
.............................................................................  
(product description, description du produit)  
to which this declaration relates is in confirmity with the following harmonized standards:  
(auquel cette déclaration se rapporte, est conforme aux normes harmonisées suivantes)  
(title, number and date of issue of the standard / titre, numéro et date de parution de la norme)  
EN 60065:2006+A1:2006+A11:2008+A2:2010+A12:2011  
EN 55013:2001+A1:2003+A2:2006  
EN61000-3-2:2006+A1:2009+A2:2009  
EN301489-1 V1.9.2 :2011  
EN300328 V1.7.1:2006  
EN 55020:2007+A11:2011  
EN61000-3-3:2008  
EN301489-17 V2.2.1 : 2012  
EN62479:2010  
EN62301 : 2005  
following the provisions of :  
(conformément aux exigences essentielles et autres dispositions pertinentes de:)  
2006/95/EC (Low Voltage Directive)  
2004/108/EC (EMC directive)  
1999/5/EC (R&TTE Directive)  
2011/65/EU (RoHS Directive)  
2009/125/EC (Eco Design) - EC/1275/2008  
And are produced under a quality scheme at least in conformity with ISO 9001 or CENELEC Permanent Documents  
(Et sont fabriqués conformément à une qualité au moins conforme à la norme ISO 9001 ou aux Documents Permanents CENELEC)  
Only for Medical Devices and R&TTE products:  
Curtis-Straus LLC/CE1797  
..................................................  
(Name and number/ nom et numéro)  
NB  
The Notified Body:  
performed:  
................................................................................  
(description of intervention / description de ’intervention)  
(L’Organisme Notifié)  
(a effectué)  
CS09942  
and issued the certificate:  
............................................................  
(et a délivré le certificat)  
(certificate number / numéro du certificat)  
Remarks:  
Drachten, Netherlands, Jan. 22, 2013  
A.Speelman, CL Compliance Manager  
.........................................................  
.........................................................  
(place,date / lieu, date)  
(signature, name and function / signature, nom et fonction)  
Philips Consumer Lifestyle B.V.  
template AMB 544-9056  
 
Specifications are subject to change without notice  
© 2013 Koninklijke Philips Electronics N.V.  
All rights reserved.  
HTL3120_12_UM_V3.0  
 

Pelco Security Camera C3410M User Manual
Philips DVD Player DVD615AT99 User Manual
Philips Light Therapy Device HB 576 77 User Manual
Philips Microcassette Recorder LFH 660 User Manual
Philips MP3 Docking Station AD7000W User Manual
Philips Surge Protector SPP3201WC User Manual
Philips TV Mount SQM5222 User Manual
Pride Mobility Mobility Aid Legend 3 User Manual
ProForm Treadmill 831246461 User Manual
PYLE Audio DVD Player PLD142 User Manual