Philips Speaker HTL4110B User Manual

Always there to help you  
Register your product and get support at  
HTL4110B  
Question?  
Contact  
Philips  
User manual  
 
Contents  
1 Important  
2
2
3
3
3
3
9 Notice  
14  
14  
14  
Safety  
Compliance  
Trademarks  
Mains fuse (UK only)  
Care for your product  
Care of the environment  
Help and support  
2 Your SoundStage  
Main unit  
4
4
5
6
Remote control  
Connectors  
3 Place your SoundStage  
6
4 Connect and set up  
7
7
Connect toTV  
Connect audio fromTV and other devices 8  
5 Use your SoundStage  
Adjust the volume  
Choose your sound  
MP3 player  
9
9
9
9
Play audio through Bluetooth  
Play music via NFC  
USB storage devices  
Auto standby  
9
10  
10  
11  
11  
Apply factory settings  
6 Update software  
Check software version  
Update software via USB  
11  
11  
11  
7
Product specifications  
12  
13  
8 Troubleshooting  
EN  
1
 
Risk of injury or damage to this product!  
1 Important  
Never place the product or any objects  
on power cords or on other electrical  
equipment.  
Read and understand all instructions before you  
use your product. If damage is caused by failure  
to follow instructions, the warranty does not  
apply.  
Read and understand all instructions before you  
use your SoundStage. If damage is caused by  
failure to follow instructions, the warranty does  
not apply.  
If the product is transported in  
temperatures below 5°C, unpack the  
product and wait until its temperature  
matches room temperature before  
connecting it to the power outlet.  
Parts of this product can be made of  
glass. Handle with care to avoid injury and  
damage.  
Risk of overheating!  
Never install this product in a confined  
space.Always leave a space of at least four  
inches around the product for ventilation.  
Ensure curtains or other objects never  
cover the ventilation slots on the product.  
Safety  
Risk of electric shock or fire!  
Never expose the product and accessories  
to rain or water. Never place liquid  
containers, such as vases, near the product.  
If liquids are spilt on or into the product,  
disconnect it from the power outlet  
immediately. Contact Consumer Care to  
have the product checked before use.  
Never place the product and accessories  
near naked flames or other heat sources,  
including direct sunlight.  
Risk of contamination!  
Do not mix batteries (old and new or  
carbon and alkaine, etc.).  
Danger of explosion if batteries are  
incorrectly replaced. Replace only with the  
same or equivalent type.  
Remove batteries if they are exhausted or  
if the remote control is not to be used for  
a long time.  
Batteries contain chemical substances, they  
should be disposed of properly.  
Never insert objects into the ventilation  
slots or other openings on the product.  
Where the mains plug or an appliance  
coupler is used as the disconnect device,  
the disconnect device shall remain readily  
operable.  
Risk of swallowing batteries!  
The product/remote control may contain  
a coin/button type battery, which can be  
swallowed. Keep the battery out of reach  
of children at all times! If swallowed, the  
battery can cause serious injury or death.  
Severe internal burns can occur within two  
hours of ingestion.  
Disconnect the product from the power  
outlet before lightning storms.  
When you disconnect the power cord,  
always pull the plug, never the cable.  
Risk of short circuit or fire!  
If you suspect that a battery has been  
swallowed or placed inside any part of the  
body, seek immediate medical attention.  
When you change the batteries, always  
keep all new and used batteries out of  
reach of children. Ensure that the battery  
compartment is completely secure after  
you replace the battery.  
Before you connect the product to the  
power outlet, ensure that the power  
voltage matches the value printed on the  
back or bottom of the product. Never  
connect the product to the power outlet if  
the voltage is different.  
2
EN  
 
If the battery compartment cannot be  
completely secured, discontinue use of the  
product. Keep out of reach of children and  
contact the manufacturer.  
Care of the environment  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
This is CLASS II apparatus with double  
insulation, and no protective earth provided.  
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product  
is covered by the European Directive 2002/96/  
EC. Please inform yourself about the local  
separate collection system for electrical and  
electronic products.  
Mains fuse (UK only)  
This information applies only to products with a  
UK mains plug.  
This product is fitted with an approved molded  
plug. If you replace the fuse, use one with:  
Please act according to your local rules and  
do not dispose of your old products with your  
normal household waste.  
the ratings shown on the plug,  
a BS 1362 approval, and  
the ASTA approval mark.  
Correct disposal of your old product helps to  
prevent potential negative consequences for the  
environment and human health.  
Contact your dealer if you are not sure about  
what type of fuse to use.  
Caution:To conform with the EMC directive  
(2004/108/EC), do not detach the plug from  
the power cord.  
Your product contains batteries covered by the  
European Directive 2006/66/EC, which cannot  
be disposed with normal household waste.  
Please inform yourself about the local rules  
on separate collection of batteries because  
correct disposal helps to prevent negative  
consequences for the environmental and  
human health.  
Copyright in the UK  
Recording and playback of material may require  
consent. See Copyright Act 1956 andThe  
Performers Protection Acts 1958 to 1972.  
Care for your product  
Use only microfiber cloth to clean the product.  
Help and support  
For extensive online support, visit  
download the user manual and the quick  
start guide  
watch video tutorials (available only for  
selected models)  
EN  
3
 
find answers to frequently answered  
questions (FAQs)  
email us a question  
2 Your  
SoundStage  
chat with our support representative.  
Follow the instructions on the website to select  
your language, and then enter your product  
model number.  
Alternatively, you can contact Consumer Care  
in your country. Before you contact, note down  
the model number and serial number of your  
product.You can find this information on the  
back or bottom of your product.  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from the  
support that Philips offers(e.g. notification  
of product software upgrade), register your  
Main unit  
This section includes an overview of the main  
unit.  
a b  
c
d
a LED display  
b
Press to switch the SoundStage on or  
off.  
Rotate to adjust the volume.  
c SOURCE  
Select an input source or Bluetooth mode  
for the SoundStage.  
d NFC tag  
Tap the NFC-enabled device on the tag for  
Bluetooth connection.  
4
EN  
 
c AUX/AUDIO IN  
Remote control  
Press repeatedly to switch your audio  
source to the AUX connection or MP3  
connection (3.5mm jack).  
This section includes an overview of the  
remote control.  
d
/
Skip to the previous or next track in USB  
mode and Bluetooth mode (only for  
AVRCP-supported Bluetooth devices).  
a
e BASS +/-  
Increase or decrease bass.  
p
o
b
c
f VOLUME +/-  
Increase or decrease the volume.  
g
n
m
Mute or restore the volume.  
h SOUND  
d
e
Select a sound mode.  
i DIM  
Set the brightness of SoundStage display  
panel.  
l
j NIGHT MODE  
f
g
Turn night mode on or off.  
k
j
k SURR  
h
i
Select stereo or virtual surround sound.  
l TREBLE +/-  
Increase or decrease treble.  
m
Start, pause or resume play in USB mode  
and Bluetooth mode (only for AVRCP-  
supported Bluetooth devices).  
a
n USB  
Switch the SoundStage on or off.  
When EasyLink is enabled, press and  
hold for at least three seconds to  
switch the connected HDMI devices  
to standby.  
Switch to USB mode.  
o COAX/OPTICAL  
Press repeatedly to switch your audio  
source to the coaxial or optical connection.  
b HDMI ARC  
Switch your source to HDMI ARC  
p
Bluetooth  
Switch to Bluetooth mode.  
connection. HDMI ARC can only be  
selected if you connect your SoundStage  
to an HDMI ARC compliantTV through  
HDMI ARC.  
EN  
5
 
3 Place your  
SoundStage  
Connectors  
This section includes an overview of the  
connectors available on your SoundStage.  
This SoundStage is designed to be placed under  
yourTV.  
Side connectors  
Caution  
The SoundStage is designed forTVs that weigh no  
more than 22 kg. Do not place a CRT typeTV on the  
SoundStage.  
Do not place the SoundStage on an unstable cart,  
stand, bracket or table. Otherwise, the SoundStage may  
fall, causing serious injury to a child or adult and serious  
damage to the product.  
Make sure the ventilation openings on the rear panel  
a AUDIO IN  
are not blocked.  
Audio input from an MP3 player (3.5mm  
jack).  
Do not change the position of the SoundStage after  
placing yourTV on top of it.  
b
1
Place the SoundStage on any flat and  
stable surface near yourTV.Then place  
yourTV on the top of the SoundStage.  
Audio input from a USB storage device.  
Rear connectors  
a b  
c
d e  
a COAXIAL IN  
Connect to a coaxial audio output on the  
TV or other devices.  
b AUX IN  
Connect to an audio output on theTV or  
other devices.  
c AC MAINS~  
Connect to the power supply.  
d HDMI OUT (ARC)  
Connect to the HDMI input on theTV.  
e OPTICAL IN  
Connect to an optical audio output on the  
TV or other devices.  
6
EN  
 
2 Make sure theTV base is centered on it  
4 Connect and set  
up  
and not hanging over any of its edges.  
This section helps you connect your  
SoundStage to aTV and other devices, and then  
set it up.  
For information about the basic connections of  
your SoundStage and accessories, see the Quick  
start guide.  
Tip  
If theTV base is too large to put on top of the  
SoundStage, place the SoundStage in another location  
such as on an open shelf under theTV, but keep it close  
to yourTV so the audio cable will reach.You can also  
mount yourTV on the wall above the SoundStage.  
If yourTV comes with an anti-tip device, install it  
according to the manufacturer's instructions and adjust  
the tether after placing theTV on top the SoundStage.  
If placing the SoundStage in a cabinet or on a shelf, for  
optimum audio performance, make sure the font of  
the SoundStage as close as possible to the front edge  
of the shelf.  
Note  
For identification and supply ratings, see the type plate  
at the back or bottom of the product.  
Before you make or change any connections, make sure  
that all devices are disconnected from the power outlet.  
Connect toTV  
If placing the SoundStage backed up to a wall, make  
sure there is at least a distance of 1 inch between the  
wall and the rear of the SoundStage.  
Connect your SoundStage to aTV to watch  
videos.You can listen to theTV audio through  
your SoundStage.  
Use the best quality connection available on  
your SoundStage andTV.  
Connect toTV through HDMI (ARC)  
Best quality audio  
Your SoundStage supports HDMI with Audio  
Return Channel (ARC). If yourTV is HDMI ARC  
compliant, you can hear theTV audio through  
your SoundStage by using a single HDMI cable.  
TV  
EN  
7
 
1 Using a High Speed HDMI cable, connect  
the HDMI OUT (ARC) connector on your  
SoundStage to the HDMI ARC connector  
on theTV.  
1 Using an optical cable, connect the  
OPTICAL IN connector on your  
SoundStage to the OPTICAL OUT  
connector on theTV or other device.  
The HDMI ARC connector on theTV  
might be labeled differently. For details,  
see theTV user manual.  
The digital optical connector might be  
labeled SPDIF or SPDIF OUT.  
2 On yourTV, turn on HDMI-CEC  
operations. For details, see theTV user  
manual.  
Option 2: Connect audio through a  
digital coaxial cable  
Good quality audio  
Note  
If yourTV is not HDMI ARC compliant, connect  
an audio cable to hear theTV audio through your  
SoundStage.  
If yourTV has a DVI connector, you can use an HDMI/  
DVI adapter to connect toTV. However, some of the  
features may not be available.  
1 Using a coaxial cable, connect the  
COAXIAL IN connector on your  
SoundStage to the COAXIAL/DIGITAL  
OUT connector on theTV or other  
device.  
Connect audio fromTV and  
other devices  
Play audio fromTV or other devices through  
your SoundStage speakers.  
Use the best quality connection available on  
yourTV, SoundStage, and other devices.  
The digital coaxial connector might be  
labeled DIGITAL AUDIO OUT.  
Option 3: Connect audio through  
analog audio cables  
Note  
Basic quality audio  
When your SoundStage andTV are connected through  
HDMI ARC, an audio connection is not required.0  
1 Using an analog cable, connect the AUX  
IN connector on your SoundStage to the  
AUDIO OUT connectors on theTV or  
other device.  
Option 1: Connect audio through a  
digital optical cable  
VCR  
Best quality audio  
TV  
8
EN  
 
Night mode  
5 Use your  
SoundStage  
For quiet listening, night mode decreases the  
volume of loud sounds when audio is played.  
Night mode is only available for Dolby Digital  
soundtracks.  
This section helps you use the SoundStage to  
play media from a wide range of sources.  
1 Press NIGHT MODE to turn night mode  
on or off.  
Before you start  
Make the necessary connections described  
in Quick start guide and User manual.  
Switch theTV to the correct source for  
the SoundStage.  
MP3 player  
Connect your MP3 player to play your audio  
files or music.  
What you need  
Adjust the volume  
An MP3 player.  
A 3.5mm stereo audio cable.  
1 Rotate the power knob or press VOLUME  
+/- on remote control to increase or  
decrease a volume level.  
1 Using the 3.5mm stereo audio cable,  
connect the MP3 player to the AUDIO IN  
connector on your SoundStage.  
To mute sound, press  
To restore the sound, press again or  
.
2 Press AUDIO IN on the remote control.  
3 Press the buttons on the MP3 player to  
press VOLUME +/-.  
select and play audio files or music.  
Choose your sound  
Play audio through Bluetooth  
This section helps you choose the ideal sound  
for your video or music.  
Through Bluetooth, connect the SoundStage  
with your Bluetooth device (such as an iPad,  
iPhone, iPod touch,Android phone, or laptop),  
and then you can listen to the audio files stored  
on the device through your SoundStage.  
Surround sound mode  
Experience an immersive audio experience with  
surround sound modes.  
What you need  
1 Press SURR repeatedly to select surround  
A Bluetooth device which supports  
Bluetooth profile A2DP, AVRCP and with  
Bluetooth version as 3.0 + EDR.  
mode or stereo mode.  
The operational range between the  
SoundStage and a Bluetooth device is  
approximately 10 meters (30 feet).  
Equalizer  
Change the high frequency (treble) and low  
frequency (bass) settings of the SoundStage.  
1 Press Bluetooth on the remote control  
to switch the SoundStage to Bluetooth  
mode.  
1 Press TREBLE +/- or BASS +/- to change  
the treble or bass level.  
» [BT] is displayed.  
EN  
9
 
2 On the Bluetooth device, switch  
on Bluetooth, search for and select  
PhilipsHTL4110B to start connection (see  
the user manual of the Bluetooth device  
on how to enable Bluetooth).  
The operational range between the main  
unit (left and right speakers) and a NFC  
device is approximately 10 meters (30  
feet).  
1 Enable NFC on your Bluetooth device (see  
3 Wait until you hear a beep sound from the  
the user manual of your device for details).  
SoundStage.  
2 Tap the NFC device on the NFC tag of  
this product until you hear a beep sound  
from this product.  
» [BT] is displayed.  
» If the connection fails, [BT] is flashed.  
» The NFC device is connected to  
this product via Bluetooth. [BT] is  
displayed.  
4
Select and play audio files or music on  
your Bluetooth device.  
During play, if a call is coming, music  
play is paused. Play resumes when the  
call ends.  
3
Select and play audio files or music on  
your NFC device.  
If your Bluetooth device supports  
AVRCP profile, on the remote control  
To break the connection, tap the  
NFC device with the NFC tag on this  
product again.  
you can press  
/
to skip to a track,  
or press  
to pause/resume play.  
5 To exit Bluetooth, select other source.  
When your switch back to Bluetooth  
mode, Bluetooth connection remains  
active.  
USB storage devices  
Enjoy audio on a USB storage device, such as an  
MP3 player and USB flash memory, etc.  
Note  
What you need  
A USB storage device that is formatted for  
FAT or NTFS file systems, and complies  
with the Mass Storage Class.  
A USB extension cable, if the USB storage  
device does not fit into the connector.  
An MP3 or WMA file on a USB storage  
device.  
The music streaming may be interrupted by obstacles  
between the device and SoundStage, such as wall,  
metallic casing that covers the device, or other devices  
nearby that operate in the same frequency.  
If you want to connect your SoundStage with another  
Bluetooth device, press and hold Bluetooth on the  
remote control to disconnect the currently connected  
Bluetooth device.  
1 Connect a USB storage device to the  
SoundStage.  
2 Press USB on the remote control.  
Play music via NFC  
» [USB] is displayed.  
3 Use the remote control to control play.  
NFC (Near Field Communication) is a  
technology that enables short-range wireless  
communication between NFC-enabled devices,  
such as mobile phones.  
Button Action  
Start, pause or resume play.  
/
Skip to the previous or next track.  
What you need  
A Bluetooth device with NFC function.  
For pairing, tap the NFC device on the  
NFC tag of this product.  
10 EN  
 
Note  
6 Update software  
This product may not be compatible with certain types  
of USB storage device.  
If you use a USB extension cable, USB HUB, or USB  
multi-reader, the USB storage device may not be  
recognized.  
To get the best features and support, update  
your product with the latest software.  
Digital camera PTP protocols are not supported.  
Do not remove the USB storage device while it is  
being read.  
DRM-protected music files (MP3,WMA) are not  
supported.  
Check software version  
Support a USB port: 5V , 1A.  
1 In any source mode, press  
.
2 Press AUX/AUDIO IN twice on the  
remote control.  
» The software version number is  
displayed.  
Auto standby  
When playing media from a connected device,  
the SoundStage automatically switches to  
standby if:  
Update software via USB  
no button is pressed for 30 minutes, or  
no audio/video play from a connected  
device (except USB) for 30 minutes.  
1 Check the latest software version on  
Search for your model and click on  
"Software and drivers".  
Apply factory settings  
2 Download the software into a USB storage  
device.  
You can reset this product to the default  
settings programmed at the factory.  
a Unzip the download if zipped, and  
make sure that the unzipped folder is  
named "HTL4110B_12.BIN".  
1 In standby mode, press and hold button  
on the main unit for at least 5 seconds  
until the product powers on.  
b Put the "HTL4110B_12.BIN" folder in  
the root directory.  
3 Connect the USB storage device to the  
USB connector of this product.  
4 Press USB on the remote control, within 5  
seconds press twice, and VOL + once,  
then hold down  
.
» If an upgrade file is detected, [UPG]  
will be fast flashed.  
» If an upgrade file is not detected,  
[ERROR] will be slowly flashed.  
5 Press to start the update.  
» [UPG] is displayed.  
EN 11  
 
6 Wait until the update is completed.  
» If the update is complete, this product  
automatically turns off and on again.  
7 Product  
specifications  
Caution  
Note  
Do not turn off the power or remove the USB storage  
device when the software update is in progress because  
you might damage this product.  
Specifications and design are subject to change without  
notice.  
Amplifier  
Total output power: 80W RMS  
(+/- 0.5 dB, 10%THD)  
Frequency response: 20 Hz-20 kHz / ±3 dB  
Signal-to-noise ratio: > 65 dB (CCIR) /  
(A-weighted)  
Input sensitivity:  
AUX: 2V rms  
AUDIO IN: 1V rms  
Audio  
S/PDIF Digital audio input:  
Coaxial: IEC 60958-3  
Optical:TOSLINK  
USB  
Compatibility: Hi-Speed USB (2.0)  
Class support: USB Mass Storage Class  
(MSC)  
File system: FAT16, FAT32, NTFS  
Maximum memory support: < 64 GB  
Supports MP3 and WMA file formats  
Sampling frequency:  
MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz,  
22 kHz, 24 kHz, 32 kHz, 44.1 kHz,  
48 kHz  
WMA: 44.1 kHz, 48 kHz  
Constant bit rate:  
MP3: 8 kbps-320 kbps  
WMA: 32 kbps-192 kbps  
Version:  
WMA:V7,V8,V9  
12 EN  
 
Bluetooth  
8 Troubleshooting  
Bluetooth profiles:A2DP, AVRCP  
Bluetooth version: 3.0 + EDR  
Warning  
Risk of electric shock. Never remove the casing of the  
product.  
Main unit  
Power supply: 110-240V~, 50/60 Hz  
To keep the warranty valid, never try to repair  
the product yourself.  
If you have problems using this product, check  
the following points before you request service.  
If you still have a problem, get support at  
Power consumption: 20 W  
Standby power consumption: ≤ 0.5 W  
Speaker impedance: 4 ohm  
Speaker drivers: 2 x racetrack mid range  
(1.5" x 5") + 2 x 1" tweeter + 1 x 4"  
woofer  
Dimensions (WxHxD):  
701 x 68 x 325 mm  
Weight: 6.3 kg  
Main unit  
The buttons on the SoundStage do not work.  
Operating temperature and humidity:  
0°C to 45°C, 5% to 90% humidity for all  
climates  
Storage temperature and humidity: -40°C  
to 70°C, 5% to 95%  
Disconnect the SoundStage from the  
power supply for a few minutes, then  
reconnect.  
Sound  
Remote control batteries  
No sound from SoundStage speakers.  
Connect the audio cable from your  
SoundStage to yourTV or other devices.  
However, you do not need a separate  
audio connection when the SoundStage  
andTV are connected through HDMI ARC  
connection.  
1 x CR2025  
Reset your SoundStage to its factory  
settings.  
On the remote control, select the correct  
audio input.  
Make sure that the SoundStage is not  
muted.  
Distorted sound or echo.  
If you play audio from theTV through  
the SoundStage, make sure that theTV is  
muted.  
EN 13  
 
Bluetooth  
9 Notice  
A device cannot connect with the SoundStage.  
The device does not support the  
compatible profiles required for the  
SoundStage.  
This section contains the legal and trademark  
notices.  
You have not enabled the Bluetooth  
function of the device. See the user manual  
of the device on how to enable the  
function.  
Compliance  
The device is not correctly connected.  
Connect the device correctly.  
The SoundStage is already connected with  
another Bluetooth device. Disconnect the  
connected device, then try again.  
This product complies with the radio  
interference requirements of the European  
Community.  
Hereby,WOOX Innovations, declares that this  
product is in compliance with the essential  
requirements and other relevant provisions of  
Directive 1999/5/EC.  
A copy of the EC declaration of Conformity  
is available in the Portable Document  
Format (PDF) version of the user manual at  
Quality of audio play from a connected  
Bluetooth device is poor.  
The Bluetooth reception is poor. Move  
the device closer to the SoundStage, or  
remove any obstacle between the device  
and the SoundStage.  
The connected Bluetooth device connects and  
disconnects constantly.  
The Bluetooth reception is poor. Move  
the device closer to the SoundStage, or  
remove any obstacle between the device  
and the SoundStage.  
Trademarks  
Turn off Wi-Fi function on the Bluetooth  
device to avoid interference.  
For some Bluetooth, the Bluetooth  
connection can be deactivated  
Manufactured under license from Dolby  
Laboratories. Dolby and the double-D symbol  
are trademarks of Dolby Laboratories.  
automatically to save power.This does not  
indicate any malfunction of the SoundStage.  
NFC  
The Bluetooth® word mark and logos are  
registered trademarks owned by Bluetooth  
SIG, Inc. and any use of such marks by WOOX  
Innovations is under license.  
A device cannot connect with this product via  
NFC.  
Make sure that the device is supported by  
NFC.  
Make sure that NFC is enabled on the  
device (see the device' s user manual for  
details).  
The terms HDMI and HDMI High-Definition  
Multimedia Interface, and the HDMI Logo are  
trademarks or registered trademarks of HDMI  
For pairing, tap the NFC device on the  
NFC tag of this product.  
14 EN  
 
Licensing LLC in the United States and other  
countries.  
The N Mark is a trademark of NFC Forum, Inc.  
in the United States and in other countries.  
EN 15  
 
Philips Consumer Lifestyle B.V.  
2013/08  
178  
(Document No.)  
(Year, Month (yyyy/mm) in which the CE mark is affixed )  
EUROPEAN DECLARATION OF CONFORMITY  
We, PHILIPS CONSUMER LIFESTYLE B.V.  
(Company name)  
TUSSENDIEPEN 4, 9206 AD DRACHTEN, THE NETHERLANDS  
(address)  
HTL4110B/12  
HTL4111B/12  
declare under our responsibility that the product(s):  
Philips  
(brand name)  
(Type version or model)  
Soundstage Speaker  
(product description)  
to which this declaration relates is in conformity with the following harmonized standards:  
EN60065:2002+A1:2006+A11:2008+A2:2010+A12:2011  
EN55013:2001+A1:2003+A2:2006, EN55020:2007+A11:2011, EN55022:2010  
EN61000-3-2:2006+A1:2009+A2:2009, EN61000-3-3:2008  
EN62479:2010  
EN50564: 2011, EN50581:2012  
EN300328 V1.7.1:2006  
EN 301489-1 V1.9.2:2011, EN301489-17 V2.2.1:2012  
following the provisions of :  
1999/5/EC  
2006/95/EC  
2004/108/EC  
2011/65/EU  
2009/125/EC - EC/1275/2008  
And are produced under a quality scheme at least in conformity with ISO 9001 or CENELEC Permanent Documents  
Only for Medical Devices and R&TTE products:  
The Notified Body:  
CE0560  
(Name and number)  
performed:  
and issued the certificate:  
Remarks:  
13214151/AA/00  
(certificate number)  
Drachten, 24-sep-13  
(place,date)  
A.Speelman, CL Compliance Manager  
(signature, name and function)  
16  
 
Philips Consumer Lifestyle B.V.  
2013/08  
178  
(Document No. / Numéro du document)  
(Year, Month (yyyy/mm) in which the CE mark is affixed / Année/mois  
(aaaa/mm) au cours de laquelle le marquage CE a été apposé)  
EUROPEAN DECLARATION OF CONFORMITY  
(DECLARATION DE CONFORMITE CE)  
We, PHILIPS CONSUMER LIFESTYLE B.V.  
(Company name / Nom de l’entreprise)  
TUSSENDIEPEN 4, 9206 AD DRACHTEN, THE NETHERLANDS  
(address / adresse)  
HTL4110B/12  
HTL4111B/12  
declare under our responsibility that the product(s)  
(déclarons sous notre propre responsabilité que le(s) produit(s))  
Philips  
(brand name, nom de la marque)  
(Type version or model, référence ou modèle)  
Soundstage Speaker  
(product description, description du produit)  
to which this declaration relates is in conformity with the following harmonized standards:  
(auquel cette déclaration se rapporte, est conforme aux normes harmonisées suivantes)  
EN60065:2002+A1:2006+A11:2008+A2:2010+A12:2011  
EN55013:2001+A1:2003+A2:2006, EN55020:2007+A11:2011, EN55022:2010  
EN61000-3-2:2006+A1:2009+A2:2009, EN61000-3-3:2008  
EN62479:2010  
EN50564: 2011, EN50581:2012  
EN300328 V1.7.1:2006  
EN 301489-1 V1.9.2:2011, EN301489-17 V2.2.1:2012  
following the provisions of :  
(conformément aux exigences essentielles et autres dispositions pertinentes de:)  
1999/5/EC  
2006/95/EC  
2004/108/EC  
2011/65/EU  
2009/125/EC - EC/1275/2008  
And are produced under a quality scheme at least in conformity with ISO 9001 or CENELEC Permanent Documents  
(Et sont fabriqués conformément à une qualité au moins conforme à la norme ISO 9001 ou aux Documents Permanents CENELEC)  
Only for Medical Devices and R&TTE products:  
The Notified Body:  
(L’Organisme Notifié)  
CE0560  
(Name and number/ nom et numéro)  
performed:  
(a effectué)  
(description of intervention / description de ’intervention)  
and issued the certificate:  
(et a délivré le certificat)  
13214151/AA/00  
(certificate number / numéro du certificat)  
Remarks:  
Drachten, 24-sep-13  
(place,date / lieu, date)  
A.Speelman, CL Compliance Manager  
(signature, name and function / signature, nom et fonction)  
17  
 
Specifications are subject to change without notice  
2013 ©WOOX Innovations Limited.All rights reserved.  
This product was brought to the market byWOOX Innovations Limited or one of its affiliates,  
further referred to in this document asWOOX Innovations, and is the manufacturer of the product.  
WOOX Innovations is the warrantor in relation to the product with which this booklet was  
packaged. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.  
HTL4110B_12_UM_V2.0  
 

Paxar Printer TC941XQR User Manual
Philips Computer Monitor 107T60 User Manual
Philips Flat Panel Television MIS F User Manual
Philips Furnace AJ 3120 User Manual
Philips MP3 Player AQ6599 User Manual
Philips Smoke Alarm 32PW6312 User Manual
Philips TV Cables SWA2553 User Manual
Pioneer Flat Panel Television PRO 150FD User Manual
Pride Mobility Mobility Aid INFMANJ2828 User Manual
PYLE Audio Car Video System PLVH72 User Manual