Setting up your DVD/CD Receiver
When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet.
Do not use these speakers with any other system or amplifier as this may result in damage or fire.
Using the remote control
Additional notes on connecting antennas
Keep antenna cables away from other cables and the
display unit and main set.
To assure optimum reception, pull the FM antenna so that
it is fully extended and not coiled or hanging at the rear of
the unit.
If reception with the supplied antenna is poor, see the
Other Connections section in the main operating
instructions for details on connecting outdoor antennas.
Check that you have all the accessories, then put
the batteries in the remote control.
Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.
The remote control can be used within a range of about 7
meters from the remote sensor on the front panel, and
within a 30 degree angle.
•
2
1
•
Precautions:
The remote control may not work if there is an obstacle
between the remote control and the display unit, or if the
remote control is not directed towards the remote sensor
of the display unit at the correct angle.
Batteries and
remote control
•
Pull off the protective
1
•
shields of both AM antenna
fig. A
fig. B
fig. C
STANDBY/ON
wires.
CD
FM/AM
TUNER
L1/L2
LINE
Power cord
•
The remote control may not work properly if strong
DVD
TV
FRONT
SURROUND
OPEN CLOSE
Additional notes on speaker placement
If your listening room is of adequate size, place the
speakers as shown in step 3 to achieve the optimum
surround sound effect. If you are listening in a fairly small
room and a typical surround speaker setup is not possible,
see Home Theater sound setup of the instruction manual
and the speaker setup guide for information on the Front
Surround speaker setup option.
light such as direct sunlight or fluorescent light is shining
onto the unit’s remote sensor.
0
8
3
7
1
4
¡
4
Push open the tabs, then insert
2
3
4
•
The remote control may not work properly when this
DVD MENU
RETURN
one wire fully into each terminal.
TUNE+
unit is used near devices emitting infrared rays, or when
remote controls of other devices which use infrared rays
are used. Also, the use of this remote control may cause
other devices to work improperly.
ST–
ST+
ENTER
TUNE–
MUTE
SOUND
6
MASTER
VOLUME
Video cord
Release the tabs to secure the AM
antenna wires.
TV CONTROL
CH
INPUT
VOL
•
When the operating range of the remote becomes too
When using the standard speaker setup as shown in step
3, please observe the following guidelines:
short, replace the batteries.
OPEN
1
•
Install the main front left and right speakers at an equal
distance from the TV.
For optimum effect, install the rear speakers slightly
above ear level.
Install the center speaker above or below the TV so that
Fix the AM loop antenna to the
attached stand.
To fix the stand to the antenna, bend in the
direction indicated by the arrow (fig. A) then
clip the loop onto the stand (fig. B).
Remote control battery caution
Incorrect use of batteries may cause leakage or
rupture.
2
4
•
3
FM antenna
Always be sure to follow these guidelines:
FM
AM
ANTENNA
UNBAL 75Ω
LOOP ANTENNA
•
•
Always insert batteries into the battery compartment
AM loop antenna
the sound of the center channel is localized at the TV
screen.
correctly matching the positive ª and negative ·
polarities, as shown by the display inside the
compartment.
Note: If you plan to mount the AM antenna
to a wall or other surface, secure the stand
with screws (fig. C) before clipping the loop
to the stand. Make sure the reception is clear.
Precautions:
•
sure to secure it with tape or some other suitable means.
Otherwise, the speaker may fall from the TV due to
external shocks such as earthquakes, endangering those
nearby or damaging the speaker.
•
•
Never mix new and used batteries.
Batteries of the same size may have different voltages,
When installing the center speaker on top of the TV, be
3
1
2
depending on brand. Do not mix different brands of
batteries.
•
When disposing of used batteries, please comply with
Place the AM antenna on a flat
surface and point in the direction
giving the best reception.
Don’t let it come into contact with metal
objects and avoid placing near computers,
television sets or other electrical appliances.
5
6
Connect the FM wire antenna to the FM UNBAL 75Ω antenna terminal.
For best results, extend the FM antenna fully and fix to a wall or door
frame. Don’t drape loosely or leave coiled up.
governmental regulations or environmental public
instruction's rules that apply in your country or area.
•
Do not connect the supplied speakers with any other
amplifier. This may result in malfunction or fire.
The front, center and surround speakers supplied
•
In order to prevent battery leakage, remove the
•
batteries when not using the remote control for an
extended period (one month or more). If leakage occurs,
carefully wipe away any battery fluid inside the
with this system are magnetically shielded. However,
placing them extremely close to a television may
result in color distortion on the screen. If this
happens, move the speakers a little further away and
switch off the television for 15-30 minutes.
Note: The signal earth (H) is designed to reduce noise that occurs when an
antenna is connected. It is not an electrical safety earth.
compartment, and replace the batteries with new ones.
•
Do not allow books or other objects to rest on top of
the remote control, since the buttons may be depressed,
causing faster exhaustion of the batteries.
•
The subwoofer is not magnetically shielded and so
should not be placed near a TV or monitor.
Since it is not magnetically shielded, do not place
•
any magnetic storage media (such as floppy disks
and tape or video cassettes) close to the subwoofer.
Connect each speaker as shown below.
Connect each speaker using the color-coded
speaker cords. Match them to the colored labels
above the speaker terminals.
3
Color-coded wire
(Connect to speaker)
Connect the DVD/CD receiver to your TV, then connect the
supplied power cord.
4
Color-coded connector
(Connect to rear panel)
Surround right
(Grey)
Surround left
(Blue)
Connect one end to a video input on your TV.
Use the supplied video cord.
1
Twist and pull off the protective
shields on each wire.
1
Connect the other end to the video output of the DVD/CD receiver.
This player is equipped with copy protection technology. Do not connect this
player to your TV via a VCR using AV cables, as the picture from this player will not
appear properly on your TV.
2
Connect the wires to the
2
IN
IN
OUT
Connect the power cord to the AC inlet.
speaker. Match the colored
wire with the color-coded
label (above the tabs), then
insert the colored wire into
the red (+) tab and the other
wire with the black (–) tab.
3
L
CENTER
6
SURROUND
6
FR6ONT
Listening position
SPEAKERS
L
L
R
AUDIO
TV
LINE 1
R
R
VIDEO IN
Subwoofer (Purple)
6
6
6
SUB
WOOFER
Connect the other end to the
color-coded speaker jacks on
the rear of the DVD/CD
receiver (as shown at left).
Make sure to insert completely.
3
IN
IN
OUT
1
OPTICAL IN
AUDIO
IN
CE6NTER
SURROUND
6
L
FR6ONT
CONTROL
SPEAKERS
L
FM
LINE
2
AM
ANTENNA
UNBAL 75Ω
LOOP ANTE
L
R
TV AUDIO LINE
R
R
AC IN
6
6
6
Y
B
R
VIDEO
OUT
VIDEO
SUB
WOOFER
COMPONENT VIDEO OUT
VIDEO
OUT
VIDEO
Center (Green)
Front left
(White)
Front right
(Red)
AC IN
For the best surround sound, setup your
speakers as above. The front left and right
speakers should be about 1.8–2.7 m apart.
To AC outlet
These speaker terminals can be hazardous when live. When you connect or
disconnect the speaker cables, to prevent the risk of electric shock, do not
touch uninsulated parts before disconnecting the power cord.
Congratulations! You're done setting up.
Printed in
<XRE3085-A>
|