Operation Instructions
Thank you for purchasing this TFT LCD Monitor, a high-resolution multi-scan color TFT LCD
Monitor.
Please read this guide thoroughly before installation.
FCC RADIO FREQUENCY INTERFERENCE STATEMENT
WARNING: (FOR FCC CERTIFIED MODELS)
This TFT LCD Monitor has been tested and found compliant with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
proper protection against harmful interference to a residential installation. This TFT LCD
Monitor generates, uses, and can radiate radio frequency energy. Harmful interference to
radio communication may be led as a result if it‘s not properly installed and used. However,
there is no guarantee that interference will not occur in a particular installation. If this TFT
LCD Monitor does cause serious interference to radio or television reception, resetting the
TFT LCD Monitor may determine it. Moreover, users are encouraged to correct interference
by doing one or more of the following:
● Reorient or relocate the receiving antenna.
● Move the TFT LCD Monitor and the receiver further away from each other.
● Connect the TFT LCD Monitor into an outlet on a circuit different from that to which
the receiver is connected.
● Consult your local dealer or an qualified technician.
FCC Warning:
To assure a continued FCC compliance, a user must use a grounded power supply cord
and the provided shielded video interface cable with bonded ferrite cores. Also, any
unauthorized changes or modifications to this TFT LCD Monitor would void the user‘s
authority to operate this device.
Note: If necessary, shielded interface cables and AC power cord must be used to meet the
emission level limits.
Important Recycle Instruction:
Lamp(s) inside this product contain mercury. This product may contain other
electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in
accordance with local, state, or federal Laws . For more information, contact the Electronic
Industries Alliance at WWW.EIAE.ORG . For lamp specific disposal information check
WWW.LAMPRECYCLE.ORG.
According to WEEE regulation, this TFT LCD Monitor can't be handled as normal
trash in Europe when it is out of usage. Please refer to the recycle information
from our website to handle it.
2
Safety Precautions
This TFT LCD Monitor is manufactured and tested on a ground principle that a user’s
safety comes first. However, improper use or installation may result danger to the TFT LCD
Monitor as well as to the user. Carefully go over the following WARNINGS before installation
and keep this guide handy.
WARNINGS:
This TFT LCD Monitor should be operated only at the correct power sources indicated
on the label on the rear end of the TFT LCD Monitor. If you’re unsure of the power
supply in your residence, consult your local dealer or power company.
Do not try to repair the TFT LCD Monitor yourself as it contains no user-serviceable
parts. The TFT LCD Monitor should only be repaired by a qualified technician.
Do not remove the TFT LCD Monitor cabinet. There is high-voltage parts inside that
may cause electric shock to human bodies, even when the power cord is disconnected.
Stop using the TFT LCD Monitor if the cabinet is damaged. Have it checked by a service
technician.
Put your TFT LCD Monitor only in a clean, dry environment. Unplug the TFT LCD
Monitor immediately if gets wet and consult your service technician.
Always unplug the TFT LCD Monitor before cleaning it. Clean the cabinet with a clean,
dry cloth. Apply non-ammonia based cleaner onto the cloth, not directly onto the
glass screen.
Keep the TFT LCD Monitor away from magnetic objects, motors, TV sets, and
transformer.
Do not place heavy objects on the cable or power cord.
For pluggable equipment the socket-outlet shall be installed near the equipment and
shall be easily accessible.
3
First Setup
Congratulations on your purchase of this high performance TFT LCD monitor.
This TFT LCD Monitor comes with the following accessories :
● User's Guide
● LCD Monitor
● Base
● Power Cable
● VGA Cable (15 pin)
Install the stand base
1. Lay the TFT LCD Monitor flat on a table with the LCD screen face down. To prevent the
monitor from being scratched, put a piece of soft cloth on the table on which the screen
will be set.
2. Unpack the base, one hand hold the monitor, the other hand attach the base to the
stand.
3. Stand the TFT LCD Monitor up.
Uninstall the stand base
1. Lay the TFT LCD Monitor flat on a table with the LCD screen face down. To prevent the
TFT LCD Monitor from being scratched, put a piece of soft cloth on the table on which
the screen will be set.
2. Hold the monitor down with one hand. With the other hand, use two fingers to press
the hooks down as directed below.
3. Remove the base from the stand.
4
Front View of the Product
1 2 3 4 5 6
1
2
3
4
5
6
Auto Image Adjust/ OSD Exits
OSD Turn On/ Confirm Selection
Scroll Down/ Adjust Decrease
Scroll UP/ Adjust Increase/ Source select
Power On/ Off
LED Indicator
5
Rear View of the Product
7
8 9
7
8
9
Power Input
VGA Input (D-Sub 15 pin)
DVI Input (DVI 24 pin)
6
Quick Installation
1. Connect either VGA or DVI Source from the monitor to the computer. Make sure both
monitor and computer are powered OFF.
2. Connect power cord to a properly grounded AC outlet, and then to the monitor.
3. Power-ON computer and then POWER-ON the monitor.
4. Set the timing mode on your computer. Recommended resolution and refresh rate
is1920 x 1080 @ 60Hz.
Example:
Power cable
7
Basic Operation
Before using the TFT LCD Monitor:
Connect external equipments properly.
Power On/Off
To turn the TFT LCD Monitor on/off:
Press POWER button on the front of TFT LCD Monitor. The power LED indicator lights green
when the TFT LCD Monitor is on.
Using the OSD Menu
You are able to use OSD menus to adjust various settings by using menu button on the
front of the TFT LCD Monitor.
The basic operation is as following:
Enter Auto mode , when not in OSD menu
Auto
Exits from OSD menu
Menu Displays main menu and enter items in OSD menu
Select the desired item when in OSD menu
When not in OSD menu, directly enters Volume adjust
Select the desired item when in OSD menu
+
Selects between VGA or DVI mode, when not in OSD menu
OSD Lock Out Function
When TFT LCD Monitor is in normal display, you can enable the “Locking OSD”function.
Option 1: OSD lock – all 4 buttons are locked except the “POWER”button.
Press and hold the Menu button for 5 seconds to lock the OSD buttons.
The TFT LCD Monitor will show an “Locking OSD” message for 2~4 seconds and the
message will disappear automatically.
Locking OSD
Repeat this step to unlock.
8
Option 2: OSD & Power button lock – all 5 buttons including the “POWER” button are
locked. Press and hold the button for 5 seconds to lock all 5 buttons.
The TFT LCD Monitor will show an “Locking Power Button” message for 2~4 seconds and
the message will disappear automatically.
Locking Power Button
Repeat this step to unlock.
9
Advanced Operation—OSD Menu
You can use the OSD menu to adjust various settings for your TFT LCD Monitor.
Press the Menu button to display the OSD Menu, and use +/- to select the desired OSD
menu.
Short Cuts Function from the button(s)
Auto Adjust: To auto adjust Horizontal Position, Vertical Position, Phase (Fine
Tune) and Clock (H. Size) of the screen.
Luminance: To adjust the Brightness and Contrast of the screen image sharpness.
Management: To manually adjust Horizontal Position, Vertical Position,
Fine Tune, Phase, and Pixel Clock.
Color Adjust: To select the color for desired brightness and color saturation
between 9300K, 6500K, 5400K, and User Color.
9300K: Adds blue to screen image for cooler white.
6500K: Adds red to screen image for warmer white and richer red.
5400K: Adds green to screen image for a darker color.
User Color: Individual adjustments for red (R), green (G), blue (B).
1. Press button Menu to select the desired color.
2. Press + or - button to adjust selected color.
OSD: To adjust the OSD menu, Horizontal Position, Vertical Position and
OSD
OSD Time Out setting on the screen display.
Language Select: To allow users to choose from available languages.
10
Recall: To recall factory settings, You can select recall color only or recall all
settings.
Information: To display the information, regarding the current input signal
coming from the graphic card in your computer. Aspect Ratio: To select full-
screen or 4:3 image size.
11
Supporting Timing Modes
STANDARD
VGA
RESOLUTION
720 x 400 @ 70Hz
640 x 480 @ 60Hz
640 x 480 @ 67Hz
640 x 480 @ 72Hz
640 x 480 @ 75Hz
800 x 600 @ 56Hz
800 x 600 @ 60Hz
800 x 600 @ 72Hz
800 x 600 @ 75Hz
832 x 624 @ 75Hz
1024 x 768 @ 60Hz
1024 x 768 @ 70Hz
1024 x 768 @ 75Hz
1280 x 960 @ 60Hz
1152 x 864 @ 75Hz
1152 x 870 @ 75Hz
1280 x 1024 @ 60Hz
1280 x 1024 @ 75Hz
1440 x 900 @ 60Hz
1400 x 1050 @ 60Hz
1600 x 1200 @ 60Hz
1680 x 1050 @ 60Hz
1920 x 1080 @ 60Hz
VGA
MAC
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
CVT
VESA
VESA
VESA
Note:
1. DVI supports 480i, 480p, 576i, 576p, 720p, 1080i, and 1080p.
Warning:
Do not set the graphic card in your computer to exceed these maximum refresh rates.
Doing so may result in permanent damage to your monitor.
12
Technical Information
LCD Panel
21.5”TFT
On: 35 Watts (typical)/55 Watts (maximum)
Standby Mode: < 1 Watt
Off: < 1 Watt
Power Management
Displayable Resolution
Pixel Dimension
LCD Display Color
Tilt
1920 x 1080 max. Vertical Frequency 60Hz max.
0.24825 x 0.24825 mm
16.7M
5° (+0/-2) ~ 20° (+/-2)
Active Display Area
Temperature
476.64 mm x 268.11 mm
Operating: 5°C ~ +35°C
Storage: -20°C ~ + 60°C
FCC-B, CE, cULus
Compliance
Power
Input Voltage AC100-240 V
13
Wall-mount instruction
Preparing To Install The Optional Wall Mount Arm (not included)
This TFT LCD Monitor can be attached to a wall mounting
2
arm you can purchase separately.
1
Turn the power OFF then disconnect the cables from the
TFT LCD Monitor before performing the procedure below.
1. Lay the TFT LCD Monitor face down on a soft surface.
2. Remove the 4 screws holding the stand to the hinge.
3. Remove the stand.
3
Attaching The Optional Wall Mount Arm (not supplied)
Follow these steps to finish installing the wall mounting
arm:
1. Place the wall mounting arm onto the back of the
TFT LCD Monitor. Line up the holes of the arm with
the holes in the back of the monitor.
2. Insert the 4 screws into the holes and tighten.
3. Reconnect the cables. Refer to the User’s Guide
that came with the optional wall mounting arm for
instructions on attaching it to the wall.
100mm x 100mm Screw
Mounting Options
100mm
100mm
4mm, 0.7 pitch
threaded holes x 4
NOTE
● 100 mm x 100 mm VESA high hole (n=4), M4, pitch =0.7 mm
screw mounting kit not included.
14
Care and Maintenance
Care
● Avoid exposing your TFT LCD Monitor directly to sunlight or other heat source. Place
your TFT LCD Monitor away from the sun to reduce glare.
● Put your TFT LCD Monitor in a well ventilated area.
● Do not place any heavy things on top of your TFT LCD Monitor.
● Make certain your TFT LCD Monitor is installed in a clean and moisture-free area.
● Keep your TFT LCD Monitor away from magnets, motors, transformers, speakers, and TV
sets.
Note
● Move the LCD out of the package and take off the plastic bag and Polystyrene Foam.
● Pull the base from Parallel versus Panel to Vertical.
● Adjust the Panel within -5( 2) degree leaning forward and 20( 2) degree leaning
backward.
Safety Tips
● If smoke, abnormal noise or odor came out from your TFT LCD Monitor, remove the
power cord immediately and call your service center.
● Never remove the rear cover of your TFT LCD Monitor cabinet. The display unit inside
contains high-voltage parts and may cause electric shock to human bodies.
● Never try to repair your TFT LCD Monitor yourself. Always call your service center or a
qualified technician to fix it.
Troubleshooting
No power
● Make sure A/C power cord is securely connected to the power adapter and the power
supply is firmly connected to the TFT LCD Monitor.
● Plug another electrical device into the power outlet to verify that the outlet is supplying
proper voltage.
● Make sure all signal cables are installed.
Power on but no screen image
● Make sure the video cable supplied with the TFT LCD Monitor is tightly secured to the
video output port on back of the computer. If not, tightly secure it.
● Adjust brightness.
Wrong or abnormal colors
● If any colors (red, green, blue) are missing, check the video cable to make sure it is
securely connected. Loose or broken pins in the cable connector could cause an
improper connection.
● Connect the TFT LCD Monitor to another computer.
15
Product Registration and Technical Support
Register Your Planar Products Today
Thank you choosing Planar. To assure you receive all the benefits of your Planar product
and services, register your Planar product today. Visit our website to register your product
Cables, Replacement Lamps, Accessories
To find cables, replacement lamps and accessories for your Planar projector, LCD monitor,
Technical Support
touch screen drivers, warranty information and access to Planar's Technical Library for
online troubleshooting. To speak with Planar Customer Support please have you model
and serial number available and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.
Hours: 24 hours a day, 7 days a week.
Toll or long distance charges may apply.
16
E030055094
|