Planar Car Video System PXL2770MW User Manual

PXL2770MW  
LED LCD Monitor  
USER'S GUIDE  
 
Content  
 
Operation Instructions  
Thank you for purchasing the PXL2770MW LED LCD monitor. Please read this guide thoroughly  
before installation.  
FCC RADIO FREQUENCY INTERFERENCE STATEMENT  
WARNING: (FOR FCC CERTIFIED MODELS)  
This  
has been tested and found compliant with the limits for a Class B digital  
LED LCD Monitor  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper  
protection against harmful interference to a residential installation. This  
LED LCD Monitor  
generates, uses, and can radiate radio frequency energy. Harmful interference to radio  
communication may be the result if it‘s not properly installed and used. However, there is no  
guarantee that interference will not occur in a particular installation. If this  
LED LCD Monitor  
does cause serious interference to radio or television reception, resetting may correct it.  
Moreover, users are encouraged to reduce interference by doing one or more of the following:  
Reorient or relocate the receiving antenna.  
Move the  
and the receiver further away from each other.  
LED LCD Monitor  
Connect the  
into an outlet on a circuit different from that to which the  
LED LCD Monitor  
receiver is connected.  
Consult your local dealer or a qualified technician.  
FCC Warning:  
To assure a continued FCC compliance, a user must use a grounded power supply cord and the  
provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized  
changes or modifications to this  
device.  
would void the user‘s authority to operate this  
LED LCD Monitor  
Note: If necessary, shielded interface cables and AC power cord must be used to meet the  
emission level limits.  
1
 
 
COMMUNIQUE D’AVERTISSEMENT DE LA FCC CONCERNANT LES INTERFERENCE DE  
FREQUENCE RADIO: (SEULEMENT POUR MODELES CERTIFIE PAR LA FCC)  
Ce moniteur a été testé et à été trouvé conforme aux limites pour un appareil numérique de  
Classe B, suivant la partie 15 des règlements de la FCC. Ces limites ont été développées pour  
offrir une protection satisfaisante contre les interférences nuisibles dans une installation  
résidentielle. Ce moniteur génère, utilise et peut radier de l’énergie de fréquence radio. Ceci  
peut causer des interférences nuisibles à des communication radio si l’appareil n’est pas  
convenablement installé et utilisé. Il n’y à néanmoins aucune garantie que des interférences  
n’apparaîtront pas dans une installation particulière. Si ce moniteur cause de sérieuses  
interférences à la réception de signaux radios ou télévisées, une possibilité est de réinitialiser le  
moniteur. Les usagers sont aussi encouragés à corriger les interférences en appliquant une ou  
plusieurs des démarches suivantes:  
Réorientez ou déplacez l’antenne de réception.  
Placez le moniteur et le récepteur plus loin l’un de l’autre.  
Connectez le moniteur à une prise différente de celle à laquelle le récepteur est connecté.  
Consultez votre revendeur local ou un technicien qualifié.  
Avertissement de la FCC:  
Pour assurez une conformité continue au règlements de la FCC, l’utilisateur doit utiliser un  
cordon d’alimentation mis à terre et le câble d’interface vidéo protégé avec noyaux en ferrite,  
fourni avec l’appareil. Chaque modification ou changement non-autorisé appliqué à ce moniteur  
peut faire perdre à l’utilisateur sont droit d’opération de cet appareil.  
Note: Si nécessaire, des câbles d’interface protégés et un cordon d’alimentation alternante  
doivent être utilisé pour être conforme aux limites d’émission.  
According to WEEE regulation, this LED LCD Monitor can't be handled as normal trash in Europe when it is  
out of usage. Please refer to the recycle information on Planar’s website to handle it.  
2
 
Unpacking Instructions  
Remove the LED LCD Monitor out of the package and take off the plastic bag and Polystyrene  
Foam.  
Pull the base from Parallel versus Panel to Vertical.  
Adjust the Panel between -5° leaning forward and 20° leaning backward.  
Safety Precautions  
Follow all warnings, precautions and maintenance as recommended in this user’s manual to  
maximize the life of your unit.  
Do:  
Turn off the product before cleaning.  
Touch screen surface may be cleaned using a soft clean cloth moistened with mild window  
glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.  
Use a soft cloth moistened with mild detergent to clean the display housing.  
Disconnect the power plug from AC outlet if the product is not going to be used for an  
extended period of time.  
Don’t:  
Do not touch the LED Display screen surface with sharp or hard objects.  
Do not use abrasive cleaners, waxes or solvents for your cleaning.  
Do not operate the product under the following conditions:  
o
o
o
o
Extremely hot, cold or humid environment.  
Areas susceptible to excessive dust and dirt.  
Near any appliance generating a strong magnetic field.  
In direct sunlight.  
If smoke, abnormal noise or odor emits from your LED LCD Monitor, remove the power cord  
immediately and call your service center.  
Never remove the rear cover of your LED LCD Monitor. The display unit inside contains  
high-voltage parts and may cause electric shock.  
LED LCD Monitor  
Never try to repair your yourself. Always call your service center or a  
qualified technician to fix it.  
Due to safety concerns, if the VESA mounting kit is purchased separately, please  
make sure the mounting kit is UL-listed, and replaceable only by service personnel.  
3
 
 
Consignes de sécurité  
Respectez tous les avertissements, les précautions et conseils d’entretien recommandés dans ce  
manuel de l’utilisateur pour maximiser la durée de vie de votre appareil.  
A faire :  
Éteindre le produit avant de le nettoyer.  
La surface de l'écran tactile peut être nettoyée avec un chiffon doux et propre imprégné d’un  
nettoyant doux du commerce pour vitres ou d'un mélange à 50/50 d'alcool isopropylique et  
d'eau.  
Utilisez un chiffon doux imprégné d'un détergeant doux pour nettoyer le carter de l'affichage.  
Débranchez la fiche d’alimentation de la prise de courant secteur si le produit ne doit pas être  
utilisé pendant une période prolongée.  
A ne pas faire :  
Ne touchez pas la surface de l’écran LED avec des objets coupants ou durs.  
N'utilisez pas des produits de nettoyage abrasifs, de la cire ou des solvants pour le nettoyage.  
N’utilisez pas le produit dans les conditions suivantes :  
o
o
o
o
Environnement extrêmement chaud, froid ou humide.  
Endroits poussiéreux ou sales.  
Près d’appareils générant un fort champ magnétique.  
Sous la lumière directe du soleil.  
Si de la fumée, un bruit anormal ou une odeur s'échappait de votre moniteur LCD LED,  
débranchez immédiatement le cordon d'alimentation et appelez votre centre de réparation.  
Ne retirez jamais le couvercle arrière de votre moniteur LCD LED. L’unité d’affichage contient  
des éléments où circule un voltage élevé et présentant un risque d'électrocution.  
N’essayez jamais de réparer vous-même votre moniteur LCD LED. Faites toujours appel à votre  
centre de service ou à un technicien qualifié pour toute réparation.  
Pour des raisons de sécurité, si vous achetez séparément le kit de fixation VESA,  
assurez-vous que celui-ci est certifié UL, et qu’il peut être remplacé uniquement par  
un technicien qualifié.  
4
 
Package Overview  
LED LCD Monitor  
Base  
AC/DC Power Adapter  
Power Cord  
(AC 100~240V Input / DC 12V Output)  
VGA Signal Cable  
Display Port Cable  
Audio-in Cable  
User’s Guide  
5
 
 
First Setup  
Install the stand base  
LED LCD Monitor  
1. Lay the  
flat on a table with the LED screen face down. To prevent the monitor  
from being scratched, put a piece of soft cloth on the table on which the screen will be set.  
2. Unpack the base, one hand hold the monitor, the other hand attach the base to the stand.  
LED LCD Monitor  
3. Stand the  
up.  
Disconnecting the stand base  
LED LCD Monitor  
LED LED  
screen face down. To prevent the  
1. Lay the  
flat on a table with the  
from being scratched, put a piece of soft cloth on the table on which the screen  
LCD Monitor  
will be set.  
2. Hold the monitor down with one hand. With the other hand, use two fingers to press the  
hooks down as directed below.  
3. Remove the base from the stand.  
6
 
 
Front View of the Product  
① ② ③ ④ ⑤ ⑥  
OSD Turn On/ Off  
Scroll Down/ Adjust Decrease/ Picture Mode/ Auto *  
Scroll UP/ Adjust Increase/ Audio Adjust/ Mute *  
Input select/ Confirm Selection  
Power On/ Off  
LED Indicator  
* Hot keys Instructions please seeUsing the OSD Menuon page 8.  
7
 
 
Rear View of the Product  
① ②  
Power Input (+12V DC In)  
④ ⑤⑥  
DisplayPort Input (DisplayPort 20 pin)  
VGA Input (D-Sub 15 pin)  
HDMI input (HDMI 19 pin)  
Audio Input  
Headphone Jack  
8
 
 
Quick Installation  
Connect either VGA, HDMI or DisplayPort Video Source from the monitor to the computer.  
Make sure both monitor and computer are powered OFF. Please note. The monitor ships  
with VGA and DisplayPort cables only. HDMI cable may be sourced separately from a cable  
supplier.  
1.  
2. Connect the audio cable from audio output of computer to the audio input of the monitor.  
3. Connect the earphone to the earphone output terminal of the monitor. (Earphone sold  
separately).  
4. Connect power cord to an AC/DC power adapter, and to a properly grounded AC outlet,  
and then to the monitor.  
5. Power-ON computer and then POWER-ON the monitor.  
6. Set the timing mode on your computer. Recommended resolution and refresh rate is 1920 x  
1080 @ 60Hz.  
Figure 1:  
PC  
Earphone  
(not supplied)  
Power cable  
AC Power cable  
AC/DC Power  
VGA cable  
DisplayPort cable  
adapter  
Audio cable  
HDMI cable  
(not supplied)  
9
 
 
Basic Operation and Calibration/Reset Instructions  
Before using the LED LCD Monitor:  
Connect external equipment properly.  
Insert the power plug, and the power LED indicator will light orange.  
Power On/Off  
To turn the LED LCD Monitor on/off:  
Press  
button on the front. The power LED indicator light will be blue when the LED LCD  
Monitor is on.  
Using the OSD Menu  
Use OSD menus to adjust settings by using the menu button on the front of the LED LCD  
Monitor.  
Displays main menu  
1
Exits from OSD menu  
2
Selects between VGA, HDMI, DisplayPort or Auto mode  
Select the desired item when in OSD menu  
When not in OSD menu, directly enters Picture Mode, press 3 seconds  
activates Auto Image Adjust.  
Select the desired item when in OSD menu  
When not in OSD menu, directly enters Audio Adjust menu, press 3  
seconds activates Mute/Unmute mode.  
+ ▲  
Recalls both Contrast and Brightness (when not in OSD menu)  
OSD Lock Out Function  
When LED LCD Monitor is in normal mode, the “OSD Lock Out” function can be enabled.  
Option 1: OSD lock – all 4 buttons are locked except the “POWER” button.  
Press and hold the 1 button and the button for 10 seconds to lock the OSD buttons.  
The LED LCD Monitor will show an “OSD LOCKED” message for 3 seconds and the message will  
disappear automatically.  
Repeat this step to unlock.  
10  
 
 
Option 2: OSD & Power button lock – all 5 buttons including the “POWER” button are locked.  
Press and hold the 1 button and the button for 10 seconds to lock all 5 buttons.  
The LED LCD Monitor will show a “POWER BUTTON LOCKED” message for 3 seconds and the  
message will disappear automatically.  
Repeat this step to unlock.  
11  
 
Advanced Operation—OSD Menu  
You can use the OSD menu to adjust various settings for your LED LCD Monitor.  
Press the 1 button to display the OSD Menu, and use or to select the desired OSD menu.  
Short Cuts Function from the button(s)  
AUTO IMAGE ADJUST: To auto adjust Horizontal Position, Vertical Position, Phase (Fine  
Tune) and Clock (H. Size) of the screen.  
CONTRAST: To adjust the foreground white level of screen image.  
: increase contrast, : decrease contrast.  
BRIGHTNESS: To adjust the luminance of the video.  
: increase brightness, : decrease brightness.  
ECO MODE: Allows the user to change the ECO mode. Contrast and Brightness  
adjustment will be disabled when ECO is active.  
Press or key to adjust the ECO Mode in three levels.  
OVER DRIVE: Allows the user to change the Over Drive strength. Improve the quality of  
the motion pictures.  
Press or key to adjust the Over Drive strength in five levels.  
12  
 
 
INPUT SELECT: When Input Select is pressed, change Input signal to D-SUB, HDMI,  
DISPLAY PORT or AUTO.  
AUDIO ADJUST: To adjust the audio functions.  
VOLUME: To adjust the volume of speaker output.  
MUTE: To turn the Mute ON/OFF.  
AUDIO INPUT: When in HDMI input, select where the audio source comes from AUDIO  
IN or HDMI. When in DisplayPort input, select where the audio source comes from  
AUDIO IN or DP.  
COLOR ADJUST: To select the color for improving brightness and color saturation  
between COOL, NORMAL, WARM, USER COLOR, and PICTURE MODE.  
COOL: Adds blue to screen image for cooler white.  
NORMAL: Adds red to screen image for warmer white and richer red.  
WARM: Adds green to screen image for a darker color.  
USER COLOR: Individual adjustments for red (R), green (G), blue (B).  
1. Press button 2 to select the desired color.  
2. Press or button to adjust selected color.  
PICTURE MODE: Provides an optimum display environment depending on the content  
displayed. It contains 4 user-selectable presets.  
STANDARD is for general windows environment and monitor default setting.  
GAME optimized for PC game environment.  
CINEMA optimized for movie and video environment.  
TEXT optimized for text editing and viewing in a word processing environment.  
INFORMATION: To display the information, regarding the current input signal coming  
from the graphic card in your computer.  
Note: See your graphic card user guide for more information about changing the  
resolution and refresh rate.  
MANUAL IMAGE ADJUST: To manually adjust the HORIZONTAL SIZE, H. /V. POSITION,  
FINE TUNE, and SHARPNESS.  
HORIZONTAL SIZE: To adjust the width of the screen image.  
: increase the width of screen image, : decrease the width of screen image.  
H./V. POSITION: To adjust the horizontal and vertical position of the video.  
H. POSITION: : move screen to the right, : move screen to the left.  
V. POSITION: : move screen up, : move screen down.  
FINE TUNE: To adjust the delay time of data and clock.  
Press or to adjust to your preference.  
SHARPNESS: To adjust the clarity of a non-Full HD Resolution (1920x1080) signal with  
or button.  
13  
 
SETUP MENU: To set up LANGUAGE SELECT, OSD POSITION, OSD TIME OUT, OSD  
BACKGROUND and LED mode.  
LANGUAGE SELECT: To allow users to choose from available languages.  
OSD POSITION: Press or button to select between horizontal and vertical OSD  
Position adjustment.  
H. POSITION: To horizontally adjust the OSD position.  
: move OSD to the right, : move OSD to the left.  
V. POSITION: To vertically adjust the OSD position.  
: move OSD up, : move OSD down.  
OSD TIME OUT: To automatically turn off On Screen Display (OSD) after a preset period  
of time.  
OSD BACKGROUND: Allows the user to turn the OSD background On or Off.  
LED: Allows the user to turn the LED Indicator On or Off.  
MEMORY RECALL: To recall factory settings for Video & Audio controls.  
Press button 2 to select the Memory Recall menu option.  
14  
 
Supporting Timing Modes  
STANDARD  
VGA  
RESOLUTION  
720 x 400 @ 70Hz  
640 x 480 @ 60Hz  
640 x 480 @ 67Hz  
640 x 480 @ 72Hz  
640 x 480 @ 75Hz  
800 x 600 @ 56Hz  
800 x 600 @ 60Hz  
800 x 600 @ 72Hz  
800 x 600 @ 75Hz  
832 x 624 @ 75Hz  
1024 x 768 @ 60Hz  
1024 x 768 @ 70Hz  
1024 x 768 @ 75Hz  
1280 x 960 @ 60Hz  
1152 x 864 @ 75Hz  
1152 x 870 @ 75Hz  
1280 x 1024 @ 60Hz  
1280 x 1024 @ 75Hz  
1440 x 900 @ 60Hz  
1440 x 900 @ 75Hz  
1400 x 1050 @ 60Hz  
1600 x 1200 @ 60Hz  
1680 x 1050 @ 60Hz  
1920 x 1080 @ 60Hz  
VGA  
MAC  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
MAC  
VESA  
VESA  
VESA  
VESA  
VESA  
MAC  
VESA  
VESA  
VESA  
VESA  
CVT  
VESA  
VESA  
VESA  
Note:  
1. HDMI and DisplayPort supports 480i, 480p, 576i, 576p, 720p, 1080i, and 1080p.  
2. Simultaneously press 1 and 2 keys on monitor panel to switch between similar PC timings.  
Similar PC Timing on list below:  
720 x 400 @ 70Hz / 640 x 400 @ 70Hz  
Warning: Do not set the graphic card in your computer to exceed these maximum refresh rates.  
Doing so may result in permanent damage to your LED LCD Monitor.  
Avertissement : Ne réglez pas la carte graphique de votre ordinateur en dépassant ces taux de  
rafraîchissement maximaux. Si vous le faites, cela va irrémédiablement détériorer votre moniteur.  
15  
 
 
Technical Information  
Panel  
27” TFT (with LED backlight)  
On: 36 Watts (typical), 44 Watts (maximum)  
Standby Mode: < 0.5 Watt  
Off: < 0.5 Watt  
Power Management  
Displayable Resolution  
Pixel Dimension  
Display Color  
Full HD 1920 x 1080 max. Vertical Frequency 60Hz max.  
0.3114 x 0.3114 mm  
16.7M  
Tilt  
-5°~20°  
Active Display Area  
Temperature  
597.888 mm x 336.312 mm  
Operating: 0°C ~ +40°C  
Storage: -20°C ~ + 60°C  
Compliance  
Power  
FCC-B, CE, UL/cUL  
Input Voltage DC +12V --- 3.5A,  
SHENZHEN HONOR (ADS-65LSI-12-1 12042G)  
Input Voltage DC +12V --- 3.33A (Max.)  
FSP (FSP040-DGAA1)  
Audio Output  
1.5W x 2  
16  
 
 
Wall-Mount Installation Instructions  
Preparing To Install The Optional Wall Mount Arm (not included)  
This LED LCD Monitor can be attached to a wall mounting arm  
you can purchase separately.  
Turn the power OFF then disconnect the cables from the LED  
LCD Monitor before performing the procedure below.  
1. Lay the LED LCD Monitor face down on a soft surface.  
2. Remove the hinge cover.  
3. Remove the 4 screws holding the stand to the hinge.  
4. Remove the stand.  
100mm x 100mm Screw  
Mounting Options  
Attaching The Optional Wall Mount Arm (not supplied)  
Follow these steps to finish installing the wall mounting arm:  
1. Place the wall mounting arm onto the back of the LED LCD  
Monitor. Line up the holes of the arm with the holes in the  
back of the monitor.  
2. Insert the 4 screws into the holes and tighten.  
3. Reconnect the cables. Refer to the User’s Guide that came  
with the optional wall mounting arm for instructions on  
attaching it to the wall.  
4mm, 0.7 pitch  
threaded holes x 4  
NOTE  
100mmx100mm VESA high hole (n=4), M4, pitch =0.7  
mm screw mounting kit not included.  
17  
 
 
Troubleshooting  
No power  
Make sure A/C power cord is securely connected to the power adapter and the power supply  
LED LCD Monitor  
is firmly connected to the  
.
Plug another electrical device into the power outlet to verify that the outlet is supplying  
proper voltage.  
Make sure all signal cables are installed.  
Power on but no screen image  
LED LCD Monitor  
Make sure the video cable supplied with the is tightly secured to the video  
output port on back of the computer. If not, tightly secure it.  
Adjust brightness.  
Wrong or abnormal colors  
If any colors (red, green, blue) are missing, check the video cable to make sure it is securely  
connected. Loose or broken pins in the cable connector could cause an improper connection.  
LED LCD Monitor  
Connect the  
to another computer.  
18  
 
 
Planar Support  
Cables and Accessories  
To find cables and accessories for your Planar monitor, touch screen or other Planar products  
visit our online store at www.PlanarOnline.com.  
Technical Support  
warranty information and access to Planar's Technical Library for online trouble shooting.  
To speak with Planar Customer Support please have your model and serial number available  
and dial:  
Planar Support  
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.  
Hours: 24 hours a day, 7 days a week.  
Toll or long distance charges may apply.  
19  
 
 

Pelco Digital Camera C2946M D User Manual
Philips Blu ray Player BDP7300 User Manual
Philips DVD Player AZ5836 User Manual
Philips Light Therapy Device HB823 User Manual
Philips Speaker System Active Speaker System User Manual
Philips TV Cables SWV7100W User Manual
Philips TV VCR Combo RT765 101 User Manual
Polaroid DVD Player PDV 0800 User Manual
Poulan Lawn Mower 181377 User Manual
Profoon Telecommunicatie Answering Machine TAM 60X User Manual