R
Operator’s Manual
Manual del Operador
Manuel de L’utilisateur
295
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual del operador y siga todas las advertencias e enstruc-
ciones de seguridad. El no hacerlo puede resultar en lesiones graves.
AVERTISSEMENT:
Lire le manuel de l’utilisateur et bien respecter tous les avertissements
et toutes les instructions de sécurité. Tout défaut de le faire pourrait en-
traîner des blessures graves.
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Augusta, GA 30907
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Mississauga, Ontario l5T 1K6
Copyright E1999 WCI Outdoor Products, Inc.
530087764
4/16/99
S
S
Move at least 10 feet (3 meters) from
fueling site before starting engine.
Turn the engine off and let saw cool in a
non-combustible area, not on dry
leaves, straw, paper, etc. Slowly re-
move fuel cap and refuel unit.
Store the unit and fuel in an area where
fuel vapors cannot reach sparks or open
flames from water heaters, electric mo-
tors or switches, furnaces, etc.
HANDLE FUEL WITH CAUTION
S
Do not smoke while handling fuel or
while operating the saw.
S
Eliminate all sources of sparks or flame
in the areas where fuel is mixed or
poured. There should be no smoking,
open flames, or work that could cause
sparks. Allow engine to cool before re-
fueling.
S
S
Mix and pour fuel in an outdoor area on
bare ground; store fuel in a cool, dry, well
ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up all fuel spills before starting
saw.
WARNING! This chain saw can be dangerous! Careless or im-
proper use can cause serious or even fatal injury.
Read and understand the Operator’s Manual before using the chain saw.
Always use two hands when operating the chain saw.
WARNING! Contacting the guide bar tip with any ob-
ject should be avoided; tip contact may cause the guide
bar to move suddenly upward and backward, which may
cause serious injury.
XX_
XX_
Measured maximum kickback value, with and without
chain brake, for the bar and chain combination on the label.
KICKBACK
back toward the operator. Either of these
reactions can cause loss of saw control
WARNING: Kickback can occur
when the moving chain contacts an object at
the upper portion of the tip of the guide bar or
when the wood closes in and pinches the
saw chain in the cut. Contact at the upper
portion of the tip of the guide bar can cause
the chain to dig into the object, which stops
the chain for an instant. The result is a light-
ning fast, reverse reaction which kicks the
guide bar up and back toward the operator. If
the saw chain is pinched along the top of the
guide bar, the guide bar can be driven rapidly
which can result in serious injury. Guard
against kickback
Rotational Kickback is the rapid upward
and backward motion of the chain saw that
can occur when the moving saw chain near
the upper portion of the tip of the guide bar
contacts an object such as a log or a branch.
Pinch-Kickback and Pull-In occur when the
chain is suddenly stopped by being pinched,
caught, or by contacting a foreign object in
3
the wood. This sudden stopping of the chain
results in a reversal of the chain force used to
cut wood and causes the saw to move in the
opposite direction of the chain rotation.
Pinch-Kickback drives the saw straight back
toward the operator. Pull-In pulls the saw
away from the operator. Either reaction can
result in loss of control and serious injury.
the engine stopped, never with the en-
gine running. Make sure the bar clamp
nuts are securely tightened after ten-
sioning the chain.
S
Begin and continue cutting at full speed.
If the chain is moving at a slower speed,
there is greater chance of kickback oc-
curring.
S
S
Cut one log at a time.
Use extreme caution when re-entering a
previous cut.
Avoid Pinch--Kickback:
S
Be extremely aware of situations or ob-
structions that can cause material to
pinch the top of or otherwise stop the
chain.
Do not cut more than one log at a time.
Do not twist the saw as the bar is with-
drawn from an undercut when bucking.
S
S
Do not attempt cuts starting with the tip
of the bar (plunge cuts).
Watch for shifting logs or other forces
that could close a cut and pinch or fall
into chain.
S
S
S
Use the Reduced--Kickback Guide Bar
and Low--Kickback Chain specified for
your saw.
Avoid Pull--In:
S
Always begin cutting with the engine at
full speed and the saw housing against
wood.
MAINTAIN CONTROL
Stand to the left of
the
S
Use wedges made of plastic or wood.
Never use metal to hold the cut open.
Kickback Path
Avoid Obstructions
Never reverse hand positions
Clear The Working Area
Elbow locked
REDUCE THE CHANCE OF
KICKBACK
Thumb on underside of
handlebar
S
Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
S
Keep a good, firm grip on the saw with
both hands when the engine is running
and don’t let go. A firm grip will help you
reduce kickback and maintain control of
the saw. Keep the fingers of your left
hand encircling and your left thumb un-
der the front handlebar. Keep your right
hand completely around the rear handle
whether your are right handed or left
handed. Keep your left arm straight with
the elbow locked.
Position your left hand on the front han-
dlebar so it is in a straight line with your
right hand on the rear handle when mak-
ing bucking cuts. Never reverse right
and left hand positions for any type of
cutting.
S
S
Never let the moving chain contact any
object at the tip of the guide bar.
Keep the working area free from ob-
structions such as other trees,
branches, rocks, fences, stumps, etc.
Eliminate or avoid any obstruction that
your saw chain could hit while you are
cutting through
branch.
a
particular log or
S
Keep your saw chain sharp and properly
tensioned. A loose or dull chain can in-
crease the chance of kickback occur-
ring. Follow manufacturer’s chain sharp-
ening and maintenance instructions.
Check tension at regular intervals with
S
4
S
S
Stand with your weight evenly balanced
on both feet.
Contoured Depth Gauge
Elongated Guard Link
Stand slightly to the left side of the saw to
keep your body from being in a direct line
with the cutting chain.
Deflects
Kickback Force
And Allows Wood
To Gradually
S
S
Do not overreach. You could be drawn
or thrown off balance and lose control of
the saw.
Do not cut above shoulder height. It is
difficult to maintain control of saw above
shoulder height.
Low---Kickback
Chain
Ride Into Cutter
KICKBACK SAFETY FEATURES
Can Obstruct Material
WARNING: The following features
are included on your saw to help reduce the
hazard of kickback; however, such features
will not totally eliminate this dangerous reac-
tion. As a chain saw user, do not rely only on
safety devices. You must follow all safety
precautions, instructions, and maintenance
in this manual to help avoid kickback and
other forces which can result in serious
injury.
Chain With High Kickback Potential
ANSI B175.1-1991 “American National
Standard for Powered Tools -- Gasoline
Powered Chain Saw -- Safety Require-
ments.”
CHAIN BRAKE AND
CKA ANGLE
S
Reduced--Kickback Guide Bar, de-
signed with a small radius tip which re-
duces the size of the kickback danger
zone on the bar tip. A Reduced--Kick-
back Guide Bar has been demonstrated
to significantly reduce the number and
seriousness of kickbacks when tested
in accordance with safety requirements
for gasoline powered chain saws as set
by ANSI B175.1.
Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter.
Low--Kickback Chain has met kickback
performance requirements when tested
on a representative sample of chain
saws below 3.8 cubic inch displacement
specified in ANSI B175.1.
Handguard, designed to reduce the
chance of your left hand contacting the
chain if your hand slips off the front han-
dlebar.
WARNING: The effectiveness of a
chain brake in reducing operator injuries has
not yet been fully determined. We cannot
represent that a chain brake is an effective
safety device to prevent or reduce the haz-
ard of injuries resulting from kickback. DO
NOT ASSUME THAT THE CHAIN
BRAKE WILL PROTECT YOU IN THE
EVENT OF A KICKBACK. Instead, use
the saw properly and carefully to avoid kick-
back. Reduced--Kickback bars and Low--
Kickback chains reduce the hazard of kick-
back and are recommended. Repairs on a
chain brake should be made by an Autho-
rized POULAN PRO Service Dealer. Take
your unit to the place of purchase if pur-
chased from a Servicing Dealer, or to the
nearest Authorized Master Service Dealer.
S
S
S
Position of front and rear handlebars,
designed with distance between han-
dles and “in-line” with each other. The
spread and “in-line” position of the
hands provided by this design work to-
gether to give balance and resistance in
controlling the pivot of the saw back to-
ward the operator if kickback occurs.
WARNING: Computed kickback
angle (CKA) listed on your saw and listed in
the CKA table below represents angle of
kickback your bar and chain combinations
will have when tested in accordance with
CSA and ANSI standards. When purchasing
replacement bar and chain, considerations
should be given to the lower CKA values.
Lower CKA values represent safer angles to
the user, higher values indicate more angle
and higher kick energies. Computed angles
represented in the non-activated column in-
dicate total energy and angle associated
without activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain break and resulting kick angle of saw.
In all cases lower CKA values represent a
safer operating environment for the user.
Reduced Kickback Symmetrical Guide Bar
Small Radius Tip
Symm
S
Tip contact in some cases may
cause a lightning fast reverse
REACTION, kicking the guide bar
up and back toward the operator.
Large Radius Tip
5
S
S
Pinching the saw chain along the
top of the guide bar may push the
guide bar rapidly back toward the
operator.
Either of these reactions may cause
you to lose control of the saw which
could result in serious injury.Do not
rely exclusively upon the safety de-
vices built into your saw.
The following guide bar and chain combina-
tions meet kickback requirements of CSA
Z62.1, Z62.3, & ANSI B175.1 when used on
saws listed in this manual. Use of bar and
chain combinations other than those listed is
not recommended and may not meet the
CKA requirements per standard.
Computed kickback angle (CKA) Table
BAR
P/N
CKA with
CKA without
chain brake
chain brake
MODEL
295
Length
18”
CHAIN P/N
952051313
12_
21_
952044578
NOTE: This saw complies with Federal
OSHA regulations for commercial logging.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
damage in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss of strength, change in skin color or
texture, or loss of feeling in the fingers,
hands, or joints, discontinue the use of this
tool and seek medical attention. An
anti-vibration system does not guarantee the
avoidance of these problems. Users who
operate power tools on a continual and
regular basis must monitor closely their
physical condition and the condition of this
tool.
ASSEMBLY
The assembly tool provided with your saw
is the only tool needed for assembly. Pro-
tective gloves (not provided) should be
worn during assembly.
ATTACHING THE BAR & CHAIN
WARNING: Recheck each assem-
bly step if the saw is received assembled. Al-
ways wear gloves when handling the chain.
The chain is sharp and can cut you even
when it is not moving!
S
Loosen and remove the clamp nuts and
the chain brake from the saw.
Remove the plastic shipping spacer (if
present).
S
Location of shipping spacer
SPECIAL NOTICE: Your saw is equipped
with a temperature limiting muffler and spark
arresting screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require
many internal combustion engines to be
equipped with a spark arrestor screen by
law. If you operate a chain saw in a state or
locale where such regulations exist, you are
legally responsible for maintaining the
operating condition of these parts. Failure to
do so is a violation of the law. Refer to the
CARE AND MAINTENANCE section for
maintenance of the Spark Arrestor.
Clamp Nuts
Chain
Assembly Tool
S
An adjusting pin and screw is used to ad-
just the tension of the chain. It is very im-
portant when assembling the bar, that
the pin located on the adjusting screw
aligns into a hole in the bar. Turning the
screw will move the adjustment pin up
and down the screw. Locate this adjust-
ment before you begin mounting the bar
onto the saw.
Failure to follow all Safety Rules and Precau-
tions can result in serious injury. If situations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your Authorized Service
Dealer or call 1-800-554-6723.
6
Inside view of
hain Brake
CHAIN TENSION
NOTE: When adjusting chain tension, make
sure the bar nuts are finger tight only. At-
tempting to tension the chain when the bar
nuts are tight can cause damage.
Checking the tension:
Adjustment located on Chain Brake
S
Turn the adjusting screw counterclock-
wise to move the adjusting pin almost as
far as it will go to the rear. This should al-
low the pin to be near the correct posi-
tion. Further adjustment may be neces-
sary as you mount the bar.
Use the screwdriver end of the combination
screwdriver/wrench tool to move the chain
around the bar. If the chain does not rotate, it
is too tight. If too loose, the chain will sag be-
low the bar.
S
S
Mount the bar as illustrated.
Slide the bar toward the rear of the saw
as far as possible.
Adjusting the tension:
S
Prepare the chain by checking the prop-
er direction. Without following the illus-
tration it is easy to place the chain on the
saw the wrong direction. Use the il-
lustration of the chain to determine the
proper direction.
Chain tension is very important. Chain
stretches during use. This is especially true
during the first few times you use your saw.
Always check chain tension each time you
use and refuel your saw.
S
Place the chain onto the sprocket lo-
cated behind the clutch drum. Fit the
chain between the teeth in the sprocket.
Start at the top of the bar and fit chain into
groove around the guide bar.
Pull the bar forward until the chain is
snug in the groove of the bar.
Hold guide bar against the saw frame
and install the bar clamp. Make sure the
adjusting pin is aligned with the hole in
the bar. Remember this pin moves the
bar forward and backward as the screw
is turned.
Replace the bar clamp nuts and tighten
finger tight. Once the chain is tensioned
you will need to tighten bar clamp nuts.
You can adjust the chain tension by loosen-
ing the bar clamp nuts and turning the adjust-
ing screw 1/4 of a turn while lifting up on the
bar.
S
S
S
S
If chain is too tight, turn adjusting
screw 1/4 turn counterclockwise.
If chain is too loose, turn adjusting
screw 1/4 turn clockwise.
S
S
S
Lift up the tip of the bar and tighten the
bar clamp nuts with the combination
screwdriver/wrench.
Recheck chain tension.
S
Chain moves freely
Mount the Bar
Tip of Bar
Lifts only 1/8 of an inch from bar.
Adjustment
Place chain onto the sprocket
7
FUELING & LUBRICATION
STARTING
FUELING ENGINE
WARNING: The chain must not
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
BURETOR ADJUSTMENT within this manual.
Avoid contact with the muffler. A hot muffler
can cause serious burns.
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good quality
2-cycle air-cooled engine oil.
We
recommend
FRIGIDAIRE
HOME
PRODUCTS brand oil. If you do not use this
oil, use a good quality 2-cycle air-cooled oil
designed to be mixed at a ratio of 40:1 (A
40:1 ratio is obtained by mixing 3.2 onces of
oil with 1 gallon of unleaded gasoline). When
mixing fuel follow the instructions printed on
the container. Always read and follow the
safety rules relating to fuel before fueling
your unit.
To stop the engine move the switch to the
STOP or OFF position.
To start the engine hold the saw firmly on
the ground as illustrated below. Make sure
the chain is free to turn without contacting
any object.
S
Move switch to the START or ON posi-
tion.
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubri-
cation. Lubrication is provided by the auto-
matic oiler system when the oil tank is kept
filled. Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shown by smoke coming from the chain and/
or discoloration of the bar.
Use only 15”---18” of rope per pull.
Hold saw firmly while pulling starter rope
In freezing weather oil will thicken, making it
necessary to thin bar and chain oil with a
small amount (5 to 10%) of #1 Diesel Fuel or
kerosene. Bar and chain oil must be free
flowing for the oil system to pump enough oil
for adequate lubrication.
Genuine POULAN or POULAN PRO bar and
chain oil is recommended to protect your unit
against excessive wear from heat and
friction. POULAN or POULAN PRO oil resists
high temperature thinning. If POULAN or
POULAN PRO bar and chain oil is not
available, use a good grade SAE 30 oil.
Important points to remember
When pulling the starter rope, do not use
the full extent of the rope as this can cause
the rope to break. Do not let starter rope
snap back. Hold the handle and let the
rope rewind slowly.
For cold weather starting, start the unit at
full choke; allow the engine to warm up be-
fore squeezing the throttle trigger.
Do not cut material with the choke/fast idle
lever at the FULL position.
S
Never use waste oil for bar and chain lu-
brication.
S
Always stop the engine before removing
the oil cap.
For cold engine or warm engine after run-
ning out of fuel.
NOTE: In the following steps, when the cho-
ke/fast idle lever is pulled out to the full ex-
tent, the correct throttle setting for starting is
set automatically.
Fuel mix cap
Oil Cap
S
Pull the choke/fast idle lever out to the
full extent.
Pull the starter rope quickly with your
right hand until the engine attempts to
start, then push the choke/fast idle lever
to the OFF position.
Pull the starter rope quickly with your
right hand until the engine starts.
Allow the engine to run for approximate-
ly five seconds. Then, squeeze and re-
lease the throttle trigger to release the
fast idle, allowing the engine to idle.
S
S
S
8
IGNITION SWITCH
(STOP)
duce the hazard of kickback and are recom-
mended. If the brake band is worn too thin it
may break when the chain brake is triggered.
With a broken brake band, the chain brake
will not stop the chain. Repairs on a chain
brake should be made by an Authorized
POULAN PRO Service Dealer. Take your
unit to the place of purchase if purchased
from a Servicing Dealer, or to the nearest Au-
thorized Master Service Dealer.
(START)
OFF
ON
CHOKE/FAST IDLE
(SIDE VIEW)
S
This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
The inertia activated chain brake is
activated if the front hand guard is
pushed forward, either manually or by
centrifugal force.
S
Choke/Fast Idle
Lever
OFF FULL
S
S
If the brake is already activated, it is
disengaged by pulling the front hand
guard back toward the front handle as
far as possible.
For a warm engine:
S
Pull the choke/fast idle lever out to the
full extent; then, push the choke/fast idle
lever back to the OFF position. This will
set the fast idle lock to the start position.
Pull the starter rope quickly with your
right hand until the engine starts.
Squeeze and release the throttle trigger
to release the fast idle lock, allowing en-
gine to idle.
When cutting with the saw, the chain
brake must be disengaged.
S
S
Braking function control
The chain brake must be checked several
times daily. Place the saw on firm ground.
Hold the handles with both hands and apply
full throttle. Activate the chain brake by turn-
ing your left wrist against the hand guard
without releasing the grip around the front
handle. The chain should stop immediately.
Difficult starting or flooded engine:
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ignition
switch is in the ON or START position.
Starting could require pulling the starter rope
handle many times depending on how badly
the unit is flooded. If engine fails to start refer
to the troubleshooting chart or call
1-800-554-6723.
Inertia activating function
control
CAUTION: When performing the following
procedure, the engine must be turned off.
Disengaged
CHAIN BRAKE
WARNING: The effectiveness of a
chain brake in reducing operator injuries has
not yet been fully determined. We cannot
represent that a chain brake is an effective
safety device to prevent or reduce the haz-
ard of injuries resulting from kickback. DO
NOT ASSUME THAT THE CHAIN BRAKE
WILL PROTECT YOU IN THE EVENT OF A
KICKBACK. Instead, use the saw properly
and carefully to avoid kickback. Reduced--
Kickback bars and Low--Kickback chains re-
The chain brake must be checked several
times daily. Hold the chain saw approxi-
mately 14” (35 cm) above a stump or other
firm object. Release your grip on the front
handle and let the saw, by its own weight,
rotate around the rear handle. When the tip
of the bar hits the stump, the brake should
activate.
9
jects. Engine noise can drown out a warning
call.
CUTTING METHODS
Remove dirt, stones, loose bark, nails, sta-
ples, and wire from the tree where cuts are to
be made.
IMPORTANT POINTS
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials,
etc.
Plan a clear retreat path
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair parts as
necessary.
Direction of Fall
S Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
and increase the possibility of kickback.
S Practice cutting a few small logs using the
following techniques to get the “feel” of us-
ing your saw before you begin a major
sawing operation.
45_
FELLING LARGE TREES
(6 inches in diameter or larger)
S Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.
S Begin cutting with the saw frame against
the log.
The notch method is used to fell large trees.
A notch is cut on the side of the tree in the de-
sired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.
S Keep the engine at full speed the entire
time you are cutting.
S Allow the chain to cut for you. Exert only
light downward pressure.
NOTCH CUT AND FELLING THE TREE
S Release the throttle trigger as soon as the
cut is completed, allowing the engine to
idle. If you run the saw at full throttle with-
out a cutting load, unnecessary wear can
occur.
S Make notch cut by cutting the top of the
notch first. Cut through 1/3 of the diameter
of the tree. Next complete the notch by cut-
ting the bottom of the notch. See illustra-
tion. Once the notch is cut remove the
notch of wood from the tree.
S After removing the cutout of wood, make
the felling cut on the opposite side of the
notch. This is done by making a cut about
two inches higher than the center of the
notch. This will leave enough uncut wood
between the felling cut and the notch to
form a hinge. This hinge will help prevent
the tree from falling in the wrong direction.
S To avoid losing control when cut is com-
plete, do not put pressure on saw at end of
cut.
S Stop the engine before setting the saw
down.
TREE FELLING TECHNIQUES
WARNING: Do not cut near build-
ings or electrical wires if you do not know the
direction of tree fall, at night since you will not
be able to see well, or during bad weather
such as rain, snow, or strong winds. as fall is
unpredictable.
Final cut here. 2 inches abov
center of notch.
First cut
Carefully plan your sawing operation in ad-
vance. You need a clear area all around the
tree so you can have secure footing. Check
for broken or dead branches which can fall
on you causing serious injury.
Notch
Natural conditions that can cause a tree to
fall in a particular direction include:
Second cut
S The wind direction and speed.
S The lean of the tree. The lean of a tree
might not be apparent due to uneven or
sloping terrain. Use a plumb or level to de-
termine the direction of tree lean.
Hinge holds tree on stump and helps
control fall
Opening
of felling
cut
S Weight and branches on one side.
S Surrounding trees and obstacles.
Look for decay and ro.t If the trunk is rotted,
it can snap and fall toward the operator.
Make sure there is enough room for the tree
to fall. Maintain a distance of 2-1/2 tree
lengths from the nearest person or other ob-
Closing of
notch
10
NOTE: Before felling cut is complete, use
wedges to open the cut when necessary to
control the direction of fall. Use wood or
plastic wedges, but never steel or iron, to
avoid kickback and chain damage.
Overcutting
Undercutting
S Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell-
ing cut, or movement in the upper
branches.
S As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
S Be extremely cautious with partially fallen
trees that may be poorly supported. When
a tree doesn’t fall completely, set the saw
aside and pull down the tree with a cable
winch, block and tackle, or tractor. To
avoid injury, do not cut down a partially fall-
en tree with your saw.
Undercutting involves cutting on the under-
side of the log with top of saw against the log.
When undercutting use light upward pres-
sure. Hold saw firmly and maintain control.
The saw will tend to push back toward you.
WARNING: Never turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
CUTTING A FALLEN TREE
First cut on pressure side of log
(BUCKING)
Bucking is the term used for cutting a fallen
tree to the desired log length.
WARNING: Do not stand on the log
being cut. Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.
Second cut
Second cut
Important points
S Cut only one log at a time.
S Cut shattered wood very carefully; sharp
pieces of wood could be flung toward oper-
ator.
First cut on pressure side of log
S Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cutting and never hold the log with your leg
or foot.
BUCKING WITHOUT A
SUPPORT
S Do not cut in an area where logs, limbs,
and roots are tangled. Drag the logs into a
clear area before cutting by pulling out ex-
posed and cleared logs first.
TYPES OF CUTTING USED
FOR BUCKING
S Overcut through 1/3 of the diameter of the
log.
S Roll the log over and finish with a second
overcut.
S Give special attention to logs under strain
to prevent the saw from pinching. Make
the first cut on the pressure side to relieve
the stress on the log.
WARNING: If saw becomes pinched
or hung in a log, don’t try to force it out. You
can lose control of the saw resulting in injury
and/or damage to the saw. Stop the saw,
drive a wedge of plastic or wood into the cut
until the saw can be removed easily. Restart
the saw and carefully reenter the cut. Do not
attempt to restart your saw when it is pinched
or hung in a log.
BUCKING USING A LOG OR
SUPPORT STAND
S Remember your first cut is always on the
pressure side of the log.
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
nd
2
Cut
Using a support stand
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
st
1
Cut
Overcutting begins on the top side of the log
with the saw against the log. When overcut-
ting use light downward pressure.
11
st
1
Cut
Second cut
Third cut
nd
Collar
2
Cut
First cut
Pruning technique
SERVICE
LIMBING AND PRUNING
WARNING: Never climb into a tree
to limb or prune. Do not stand on ladders,
platforms, a log, or in any position which can
cause you to lose your balance or control of
the saw.
We recommend all service and adjustments
not listed in this manual be performed by an
Authorized Service Dealer.
MAINTENANCE SCHEDULE
Check For:
Fuel Mixture Level. Before each use
Bar Lubrication . . . Before each use
Chain Tension . . . . Before each use
Chain Sharpness . Before each use
Damaged parts . . . Before each use
Loose caps . . . . . . Before each use
Loose fasteners . . Before each use
Inspect and Clean:
IMPORTANT POINTS
S Watch out for springpoles. Use extreme
caution when cutting small size limbs.
Slender material may catch the saw chain
and be whipped toward you or pull you off
balance.
S Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or the
saw when the tension in the wood fibers is
released.
S Frequently clear branches out of the way
to avoid tripping over them.
Bar . . . . . . . . . . . . . Before each use
Complete saw . . . . After each use
Clean cylinder fins After each use
Air filter . . . . . . . . . . Every 5 hours *
Spark arrestor . . . . Every 25 hours *
Replace spark plug Yearly
Replace fuel filter . . Yearly
* Hours of Operation
LIMBING
AIR FILTER
S Always limb a tree after it is cut down. Only
then can limbing be done safely and prop-
erly.
S Leave the larger limbs underneath the
felled tree to support the tree as you work.
S Start at base of the felled tree and work to-
ward the top, cutting branches and limbs.
Remove small limbs with one cut.
S Keep the tree between you and the chain
as much as possible.
S Remove larger, supporting branches with
the 1/3, 2/3 cutting techniques described in
the bucking section.
S Always use an overcut to cut small and
freely hanging limbs. Undercutting could
cause limbs to fall and pinch saw.
CAUTION: Do not clean filter in gasoline or
other flammable solvent to avoid creating a
fire hazard or producing harmful evaporative
emissions.
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
Cleaning the air filter:
S Clean the cover and the area around it to
keep dirt and sawdust from falling into the
carburetor chamber when the cover is re-
moved.
S Remove the parts as illustrated.
S Wash the filter in soap and water.
PRUNING
WARNING: Limit pruning to limbs
shoulder height or below. Do not cut if
branches are higher than your shoulder. Get
a professional to do the job.
S
Make your fist cut 1/3 of the way
through the bottom of the limb.
Next make a 2nd cut all the way
through the limb. Then cut a
third overcut leaving a 1 to 2 inch
collar from the trunk of the tree.
S
12
electric motors or switches, furnaces, etc.
Store unit with all guards in place. Position so
that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.
BAR MAINTENANCE
If your saw cuts to one side, has to be forced
through the cut, or been run with an improper
amount of bar lubrication it may be neces-
sary to service your bar. A worn bar will dam-
age your chain and make cutting
difficult.
S
Before storing, drain all fuel from the
unit. Start engine and allow to run until it
stops.
Replace your bar if bent or the inside rails of
the bar are worn.
S
Clean the unit before storing. Pay partic-
ular attention to the air intake area, keep-
ing it free of debris. Use a mild detergent
and sponge to clean the plastic sur-
faces.
S
S
Clean the oil holes after each 5 hours of
operation
Remove sawdust from bar groove peri-
odically with a wire or putty knife.
S
S
Do not store the unit or fuel in a closed
area where fuel vapors can reach
sparks or an open flame from hot water
heaters, electric motors or switches, fur-
naces, etc.
Store in a dry area out of the reach of
children.
Guide Bar
Groove
CAUTION: It is important to prevent gum de-
posits from forming in essential fuel system
parts such as the carburetor, fuel filter, fuel
hose, or fuel tank during storage. Alcohol
blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to fuel mixture separation and
formation of acids during storage. Acidic gas
can damage the engine.
Oil Holes
CARBURETOR ADJUSTMENTS
Carburetor adjustment is critical and if done
improperly can permanently damage your
unit. We recommend you contact an Autho-
rized Service Dealer for adjustments.
IDLE SPEED ADJUSTMENT: Turn the Idle
Speed Screw clockwise until it stops. Now
turn the screw counterclockwise 4-1/2 turns.
This should allow the engine to run without
the chain turning. If the chain moves at idle
speed, do not use your unit. Contact an Au-
thorized Service Dealer. Idle speed is cor-
rect when engine runs without stalling and
chain does not turn.
MIXTURE ADJUSTMENTS: If your carbu-
retor includes limiter caps (Plastic caps on
the mixture screws) , do not force the screws
beyond the stops of the limiter caps or dam-
age will occur. Do not remove these caps.
Small adjustments will affect your unit. Do
not adjust more than 1/16th turn without
checking performance.
TROUBLESHOOTING
Engine will not start.
S Ignition switch off.
S Engine flooded.
S Fuel tank empty.
S Spark plug not firing.
S Fuel not reaching carburetor.
Engine will not idle properly.
S Carburetor requires adjustment.
S Crankshaft seals worn.
Engine will not accelerate, lacks
power, or dies under a load.
CHAIN SHARPENING
S Air filter dirty.
S Spark plug fouled.
Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to a professional
chain sharpener. If you choose to perform
your own chain sharpening, call our toll-free
helpline and order a free chain sharpening
guide. (See the back page of this manual for
the toll-free phone number.)
S Carburetor requires adjustment.
Engine smokes excessively.
S Too much oil mixed with gasoline
NEED ASSISTANCE?
IGNITION TIMING
Need Assistance?
Call 1-800-554-6723.
Need Service Part?
Contact your retailer.
Ignition timing is fixed and nonadjustable.
SPARK PLUG
Replace the spark plug yearly using a Cham-
pion RCJ7Y. Gap to .025”.
STORAGE
WARNING: Stop engine and allow to
cool, and secure the unit before storing or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
13
and require replacement with reasonable
use during the warranty period. This warran-
ty does not cover predelivery set--up, instal-
lation of guide bar and chain, and normal ad-
justments explained in the operator’s
manual such as carburetor adjustments and
chain tension adjustments. This warranty
does not cover transportation costs.
LIMITED WARRANTY
FRIGIDAIRE HOME PRODUCTS Division
WCI Outdoor Products, Inc., warrants to the
original purchaser that each new Poulan or
Poulan Pro brand gasoline chain saw is free
from defects in material and workmanship
and agrees to repair or replace under this
warranty any defective gasoline chain saw
as follows from the original date of purchase.
1 YEAR -- Parts and Labor, when used for
Household purposes.
60 DAYS -- Parts and Labor, when used for
Commercial, Professional, or Income Pro-
ducing purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLY TO YOU.
FRIGIDAIRE HOME PRODUCTS policy is
to continuously improve its products. There-
fore, FRIGIDAIRE HOME PRODUCTS re-
serves the right to change, modify, or discon-
tinue models, designs, specifications, and
accessories of all products at any time with-
out notice or obligation to any purchaser.
This warranty is not transferable and does
not cover damage or liability caused by im-
proper handling, improper maintenance, or
the use of accessories and/or attachments
not specifically recommended by FRIGID-
AIRE HOME PRODUCTS for this chain
saw. Additionally, this warranty does not
cover damage caused by improper handling,
improper maintenance, or if the saw is al-
tered in any way which in our judgement af-
fects its condition or operation. This warranty
does not cover tune--up, spark plugs, filters,
starter ropes, starter springs, chain sharpen-
ing, bars, chains, and other parts which wear
U.S. EPA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U. S. Environmental
Protection Agency/Environment Canada
and POULAN/WEED EATER, DIVISION
OF WCI OUTDOOR PRODUCTS, INC., are
pleased to explain the emissions control
system warranty on your lawn and garden
equipment engine. All new utility and lawn
and garden equipment engines must be de-
signed, built, and equipped to meet the strin-
gent anti--smog standards. POULAN/
WEED EATER must warrant the emission
control system on your lawn and garden
equipment engine for the periods of time
listed below provided there has been no
abuse, neglect, or improper maintenance of
your lawn and garden equipment engine.
Your emission control system includes parts
such as the carburetor and the ignition sys-
tem. Where a warrantable condition exits,
POULAN/WEED EATER will repair your
lawn and garden equipment engine at no
cost to you. Expenses covered under war-
ranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions related part on
your engine (as listed under Emissions Con-
trol Warranty Parts List) is defective or a de-
fect in the materials or workmanship of the
engine causes the failure of such an emis-
sion related part, the part will be repaired or
replaced by POULAN/WEED EATER.
OWNER’S WARRANTY RESPONSIBILI-
TIES: As the lawn and garden equipment en-
gine owner, you are responsible for the per-
formance of the required maintenance listed
in your instruction manual. POULAN/WEED
EATER recommends that you retain all re-
ceipts covering maintenance on your lawn
and garden equipment engine, but POU-
LAN/WEED EATER cannot deny warranty
solely for the lack of receipts or for your fail-
ure to ensure the performance of all sched-
uled maintenance. As the lawn and garden
equipment engine owner, you should be
aware that POULAN/WEED EATER may
deny you warranty coverage if your lawn and
garden equipment engine or a part of it has
failed due to abuse, neglect, improper main-
tenance, unapproved modifications, or the
use of parts not made or approved by the
original equipment manufacturer. You are
responsible for presenting your lawn and
garden equipment engine to a POULAN/
WEED EATER authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount
of time, not to exceed 30 days. If you have
any questions regarding your warranty
rights and responsibilities, you should con-
tact your nearest authorized service center
or call POULAN/WEED EATER at
1--800--554--6723.
WARRANTY COM-
MENCEMENT DATE: The warranty period
14
begins on the date the lawn and garden
equipment engine is purchased. LENGTH
OF COVERAGE: This warranty shall be for
a period of two years from the initial date of
purchase. WHAT IS COVERED: REPAIR
OR REPLACEMENT OF PARTS. Repair or
replacement of any warranted part will be
performed at no charge to the owner at an
approved POULAN/WEED EATER servic-
ing center. If you have any questions regard-
ing your warranty rights and responsibilities,
you should contact your nearest authorized
service center or call POULAN/WEED EAT-
ER at 1--800--554--6723 WARRANTY PE-
RIOD: Any warranted part which is not
scheduled for replacement as required
maintenance, or which is scheduled only for
regular inspection to the effect of “repair or
replace as necessary” shall be warranted for
2 years. Any warranted part which is sched-
uled for replacement as required mainte-
nance shall be warranted for the period of
time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determination that a war-
ranted part is defective if the diagnostic work
is performed at an approved POULAN/
WEED EATER servicing center. CONSE-
QUENTIAL DAMAGES: POULAN/WEED
EATER may be liable for damages to other
engine components caused by the failure of
a warranted part still under warranty. WHAT
IS NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance
are not covered. ADD--ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. POULAN/WEED EATER is not liable to
cover failures of warranted parts caused by
the use of add--on or modified parts. HOW
TO FILE A CLAIM: If you have any ques-
tions regarding your warranty rights and re-
sponsibilities, you should contact your near-
est authorized service center or call
POULAN/WEED
EATER
at
1--800--554--6723 . WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all POULAN/WEED
EATER
service
centers.
call:
1--800--554--6723 MAINTENANCE, RE-
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any POULAN/WEED
EATER approved replacement part used in
the performance of any warranty mainte-
nance or repair on emission related parts will
be provided without charge to the owner if
the part is under warranty. EMISSION CON-
TROL WARRANTY PARTS LIST: Carbure-
tor, Ignition System: Spark Plug (covered up
to maintenance schedule), Ignition Module.
MAINTENANCE STATEMENT: The owner
is responsible for the performance of all re-
quired maintenance as defined in the in-
struction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
15
|