R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
300
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2
Copyright E2003 Electrolux Home Products, Inc.
530403514
2/11/03
S Keep the handles dry and clean and
free from oil and grease.
larized extension cord only one way. If
the plug does not fit fully into the exten-
sion cord, reverse the plug. If the plug
still does not fit, obtain a correct polar-
ized extension cord. A polarized exten-
sion cord will require the use of a polar-
ized wall outlet. This plug will fit into the
polarized wall outlet only one way. If
plug does not fit fully into the wall outlet,
reverse the plug. If the plug still does not
fit, contact a qualified electrician to install
the proper wall outlet. Do not change the
equipment plug, extension cord recep-
tacle, or extension cord plug in any way.
S Keep oil cap and fasteners securely
tightened.
S Nonconforming replacement compo-
nents or the removal of safety devices
may cause damage to the unit and pos-
sible injury to the operator or bystand-
ers. Use only Poulan accessories and
replacement parts as recommended.
Never modify your saw.
S Maintain chain saw with care.
S Keep unit sharp and clean for better
and safer performance.
S Follow instructions for lubricating and S To reduce risk of electrical shock, use
changing accessories.
S Unplug the chain saw from the power
source when not in use, before servic-
ing, and when changing accessories
and attachments, such as saw chain
and guard.
extension cords specifically marked as
suitable for outdoor appliances. The
electrical rating of the cord must not be
less than the rating of unit. The cord
must be marked with suffix “W--A” (in
Canada, “W”). Use a polarized cord.
Make sure your extension cord is in
good condition. Inspect extension cord
before use and replace if damaged. Do
not use a damaged cord. Cord insula-
tion must be intact with no cracks or de-
terioration. Plug connectors must be
undamaged. An undersized extension
cord will cause a drop in line voltage re-
sulting in loss of power and overheating.
If in doubt, use the next heavier gauge.
The lower the gauge number, the heavi-
er the cord (see SELECT AN EXTENSION
CORD in the OPERATION section). Do
not use multiple cords.
S Check for damaged parts. Before fur-
ther use of the chain saw, a guard or
other part that is damaged should be
carefully checked to determine that it will
operate properly and perform its in-
tended function. Check for alignment of
moving parts, binding of moving parts,
breakage of parts, mounting and any
other conditions that may affect its op-
eration. A guard or other part that is
damaged should be properly repaired
or replaced by an authorized service
dealer unless otherwise indicated else-
where in the instruction manual.
S When not in use, chain saws should S Do not abuse cord. Never carry the
be stored in a dry, high or locked-up
place out of the reach of children.
unit by the extension cord or yank ex-
tension cord to disconnect unit.
S When storing saw, unplug and use a S Secure extension cord to power cord
bar sheath or carrying case.
ELECTRICAL SAFETY
to prevent disconnection from unit.
S Do not use the unit if the switch does
not turn the unit on and off properly, or
if the lockout does not work. Repairs to
the switch must be made by an autho-
rized service dealer.
S Keep extension cord clear of operator
and obstacles at all times. Position
cord so that it will not be caught on
branches. Do not expose cords to
heat, oil, water, or sharp edges.
S To avoid the possibility of electric
shock, avoid body contact with any
grounded conductor, such as metal
fences or pipes.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on circuit
or outlet to be used. Receptacles are
available having built-in GFCI protection
and may be used for this measure of
safety. Inspect chain saw cords periodi-
cally and if damaged, have repaired by
an authorized service dealer.
WARNING: Avoid a dangerous
environment. To reduce the risk of elec-
trical shock, do not use in rain, in damp
or wet locations, or around swimming
pools, hot tubs, etc. Do not expose to
snow, rain, or water to avoid the possibil-
ity of electrical shock. Do not handle ex-
tension cord or plug with wet hands.
S Use a voltage supply as shown on the
nameplate of the unit.
S Avoid dangerous situations. Do not
use in the presence of flammable liq-
uids or gases to avoid creating a fire or
explosion and/or causing damage to
unit.
S To reduce the risk of electrical shock,
this appliance has a polarized plug (one
blade is wider than the other) and will re-
quire the use of a polarized extension
cord. The appliance plug will fit into a po-
3
GUARD AGAINST KICKBACK
Follow all safety rules to help avoid kick-
back and other forces which can result in
serious injury.
S Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
S Never let the moving chain contact
any object at the tip of the guide bar.
S Keep working area free from obstruc-
tions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate
or avoid any obstruction that your saw
chain could hit while cutting.
Kickback Path
Avoid Obstructions
S When cutting a branch, do not let the
guide bar contact another branch or
other objects around it.
S Keep saw chain sharp and properly
tensioned. A loose or dull chain can in-
crease the chance of kickback. Follow
manufacturer’s chain sharpening and
maintenance instructions. Check ten-
sion at regular intervals, but never with
engine running. Make sure bar mount-
ing nuts are securely tightened.
S Begin and continue cutting at full
speed. If the chain is moving at a slow-
er speed, there is greater chance of
kickback occurring.
S Use extreme caution when re-enter-
ing a cut.
S Do not attempt cuts starting with the tip
of the bar (plunge cuts).
S Watch for shifting logs or other objects
that could close a cut and pinch or fall
onto chain.
S Use the specified Reduced-Kickback
Guide Bar and Low Kickback Chain.
Avoid Pinch-Kickback:
Clear The Working Area
WARNING: Avoid kickback which
can result in serious injury. Kickback is
the backward, upward or sudden for-
ward motion of the guide bar occurring
when the saw chain near the upper tip of
the guide bar contacts any object such
as a log or branch, or when the wood
closes in and pinches the saw chain in
the cut. Contacting a foreign object in
the wood can also result in loss of chain
saw control.
S Rotational Kickback can occur when
the moving chain contacts an object at
the upper tip of the guide bar. This con-
tact can cause the chain to dig into the
object, which stops the chain for an
instant. The result is a lightning fast,
reverse reaction which kicks the guide
bar up and back toward the operator.
S Pinch-Kickback can occur when the
the wood closes in and pinches the
moving saw chain in the cut along the
top of the guide bar and the saw chain
is suddenly stopped. This sudden
stopping of the chain results in a rever-
sal of the chain force used to cut wood
and causes the saw to move in the op-
posite direction of the chain rotation.
The saw is driven straight back toward
the operator.
S Be extremely aware of situations or
obstructions that can cause material
to pinch the top of or otherwise stop
the chain.
S Do not cut more than one log at a time.
S Do not twist the saw as the bar is with-
drawn from an undercut when buck-
ing.
Avoid Pull-In:
S Always begin cutting with the saw at
full speed and the saw housing
against wood.
S Use wedges made of plastic or wood.
Never use metal to hold the cut open.
S Pull-In can occur when the moving
chain contacts a foreign object in the
wood in the cut along the bottom of the
guide bar and the saw chain is suddenly
stopped. This sudden stopping pulls the
saw forward and away from the opera-
tor and could easily cause the operator
to lose control of the saw.
REDUCE THE CHANCE OF
KICKBACK
The following precautions should be fol-
lowed to minimize kickback:
MAINTAIN CONTROL
The following precautions should be fol-
lowed to minimize kickback.
S A good, firm grip on the saw with both
hands will help you maintain control.
Don’t let go. Grip the rear handle with
your right hand whether you are right
or left handed. Wrap the fingers of
your left hand over and around the
front handlebar, and your left thumb
under the front handlebar. Keep your
left arm straight with the elbow locked.
4
Small Radius
Tip Guide Bar
Right Hand
Left Hand
Large Radius
Tip Guide Bar
S Low Kickback Chain has metkickback
performance requirements when
tested on the representative sample of
these chain saws specified in ANSI
B175.1.
S Position your left hand on the front
handlebar so it is in a straight line with
your right hand on the rear handle
when making bucking cuts. Stand
slightly to the left side of the saw to
keep your body from being in a direct
line with the cutting chain.
Low Kickback Chain
Contoured Depth Gauge
Elongated Guard Link
Deflects Kickback Force
And Allows Wood To
S Stand with your weight evenly bal-
anced on both feet.
Gradually Ride Into Cutter
S Do not overreach. You could be drawn
or thrown off balance and lose control.
S Do not cut above shoulder height. It is
WARNING: Computed Kickback
difficult to maintain control of saw Angle (CKA) listed on your saw and listed
above shoulder height.
KICKBACK SAFETY FEATURES
in the following CKA Table represents the
angle of kickback your bar and chain
combinations will have when tested in ac-
WARNING: The following features cordance with CSA and ANSI standards.
are included on your saw to help reduce Computed angles represented in the CKA
hazard of kickback; however, such fea- column indicate total energy and angle
tures will not totally eliminate this dan- associated without a chain brake. When
ger. Do not rely only on safety devices. purchasing replacements, considerations
Follow all safety rules to help avoid kick- should be given to the lower CKA values.
back and other forces which can result In all cases, lower CKA values represent a
in serious injury.
safer operating environment for the user.
S Hand Guard: designed to reduce the S Tip contact in some cases may cause
chance of your left hand contacting
the chain if your hand slips off the front
handlebar.
a lightning fast REACTION, kicking the
guide bar up and back toward the op-
erator.
S Position of front and rear handlebars: S Pinching the saw chain along the tip of
designed with distance between han-
dles and “in-line” with each other. The
spread and “in-line” position of the S Either of these reactions may cause
the guide bar may push the guide bar
rapidly back towards the operator.
hands provided by this design work to-
gether to give balance and resistance in
controlling the pivot of the saw back to-
ward the operator if kickback occurs.
you to lose control of the saw which
could result in serious injury. Do not
rely exclusively upon safety devices
built into your saw.
S Reduced-Kickback Guide Bar: de- The following guide bar and chain com-
signed with a small radius tip which re- binations meet kickback requirements of
duces the size of the kickback danger CSA Z62.1 & Z62.3 and ANSI B175.1
zone. This type bar has been demon- when used on saws listed in this manual.
strated to significantly reduce the num- Use of bar and chain combinations other
ber and seriousness of kickbacks when than those listed is not recommended and
tested in accordance with ANSI B175.1. may not meet the CKA requirements per
standard.
5
Computed kickback angle (CKA) Table
BAR
MODEL
ES300
CHAIN P/N
952051469
CKA
P/N
Length
14!
952044758
20_
SAFETY NOTICE: Exposure to vibra- double insulation system only provides
tions through prolonged use of hand added protection against injury resulting
tools could cause blood vessel or nerve from an internal electrical insulation
damage in the fingers, hands, and joints failure.
of people prone to circulation disorders
WARNING: All electrical repairs to
this unit, including housing, switch, motor,
etc., must be diagnosed and repaired by
qualified service personnel. Replacement
parts for a double insulated appliance
must be identical to the parts they replace.
A double insulated appliance is marked
with the words “double insulation” or
“double insulated”. The symbol
(square within a square) may also be
marked on the appliance. Failure to have
the unit repaired by authorized service
personnel can cause the double insula-
tion construction to become ineffective
and result in serious injury.
STANDARDS: This product is listed by
Underwriters Laboratories, Inc. inaccor-
dance with UL Standard 1662 and CSA
Standards Z62.1 and Z62.3 and ANSI
B175.1.
ANSI B175.1--2000 “American National
Standard for Powered Tools -- Safety Re-
quirements”
or abnormal swelling. Prolonged use in
cold weather has been linked to blood
vessel damage in otherwise healthy
people. If symptoms occur such as
numbness, pain, loss of strength,
change in skin color or texture, or loss of
feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration sys-
tem does not guarantee the avoidance
of these problems. Users who operate
power tools on a continual and regular
basis must closely monitor their physical
condition and the condition of this tool.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help pro-
tect against electric shock. Double in-
sulation construction consists of two
separate “layers” of electrical insulation
instead of grounding.
Tools built with this insulation systemare
not intended to be grounded. No
grounding means is provided on this
unit, nor should a means of grounding
be added to this unit.
Safety precautions must be observed
when operating any electrical tool. The
CSA Z62.3 “Chain Saw Kickback Occu-
pational Health and Safety”
CSA Z62.1 “Chain Saws -- Occupational
Health and Safety”
SAVE THESE INSTRUCTIONS
ASSEMBLY
CARTON CONTENTS
Check carton contents against the fol-
lowing list.
NOTE: If you need assistance or find
that parts are missing or damaged,
please call 1-800-554-6723.
ASSEMBLY
Your unit is fully assembled; no assembly
is required.
S Chain Saw (fully assembled)
S Bar Sheath
Examine parts for damage. Do not use
damaged parts.
6
OPERATION
KNOW YOUR SAW
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the
location of the various controls and adjustments. Save this manual for future refer-
ence.
Hand Guard
Bar Oil Cap
Trigger Lockout
Button
Chain Adjustment Screw
Power
Cord
Bar
Trigger Switch Bar Clamp
BAR OIL CAP
Chain
TRIGGER SWITCH
The TRIGGER SWITCH is used to turn on The BAR OIL CAP is used to fill the bar oil
the unit. Squeeze the trigger switch to tank.
operate the unit after lock--out button CHAIN ADJUSTMENT SCREW
has been pushed forward. Release the The CHAIN ADJUSTMENT SCREW is
trigger to turn the unit off.
used to adjust the chain tension.
TRIGGER LOCK--OUT BUTTON
POWER CORD
The TRIGGER LOCK--OUT BUTTON is a
control feature designed to prevent the
motor from being accidently started.
When the rear handle is gripped in a nor-
mal cutting position, the lock--out button
can be pushed in by the thumb, permit-
ting the index finger to squeeze the trig-
ger. It is not necessary to maintain pres-
sure on the lock--out button once the
trigger has been engaged.
The POWER CORD is used to connect
the chain saw to an approved extension
cord.
CHAIN TENSION
It is normal for a new chain to stretch dur-
ing first 30 minutes of operation. You
should check your chain tension frequent-
ly. See CHAIN TENSION under the SER-
VICE AND ADJUSTMENTS section.
OPERATING INSTRUCTIONS
Use only a voltage supply as specified on
your unit.
SELECT AN EXTENSION CORD
Extension cords are available for this unit .
MINIMUM WIRE GAUGE
RECOMMENDATIONS
Extension Cord
BEFORE STARTING SAW
50 ft.
100 ft.
25 ft.
(7.67 M)
16
A.W.G.*
Volts
120
(15.24 M) (30.48 M)
16
A.W.G.*
WARNING: Be sure to read the
electrical safety information in the safety
rules section of this manual before you
begin. If you do not understand the elec-
trical safety information donot attempt to
use your unit. Seek help from someone
14
A.W.G.*
*American Wire Gauge
ATTACH THE EXTENSION CORD TO
YOUR CHAIN SAW
To prevent disconnection from unit, se- that does understand the information or
cure extension cord to power cord as call the customer assistance help line at
shown in the following illustration.
1-800-554-6723.
7
GUIDE BAR AND CHAIN OIL
S Keep the cord away from the cutting
area. Position cord so it will not be
caught on branches and the like dur-
ing cutting.
S To avoid losing control when cut is
complete, do not put pressure on
saw at end of cut.
The bar and chain require lubrication. The
chain oiler provides lubrication to the
chain and guide bar. Be sure to fill the bar
oil tank before each cutting session. Lack
of oil will quickly ruin the bar and chain.
Too little oil will cause overheating shown
by smoke coming from the chain and/or S Stop motor before setting saw down.
discoloration of the bar. For maximum
guide bar and chain life, we recommend
you use Poulan chain saw bar oil. If
Poulan bar oil is not available, you may
use a good grade SAE 30 oil until you are
able to obtain Poulan brand. Use a funnel
to fill the tank. Replace oil cap securely.
Check oil level after every 15 minutes of
operation.
TREE FELLING TECHNIQUES
WARNING: Check for broken or
dead branches which can fall while cut-
ting causing serious injury. Do not cut
near buildings or electrical wires if you
do not know the direction of tree fall, nor
cut at night since you will not be able to
see well, nor during bad weather such
as rain, snow, or strong winds, etc. If the
tree does make contact with any utility
line, the utility company should be noti-
fied immediately.
S Carefully plan your sawing operation in
advance.
S Clear the work area. You need a clear
area all around the tree so you can
have secure footing.
S The chain saw operator should keep
on the uphill side of the terrain as the
tree is likely to roll or slide downhill
after it is felled.
S Study the natural conditions that can
cause the tree to fall in a particular
direction, such as:
S The wind direction and speed.
S The lean of the tree. The lean of a
tree might not be apparent due to un-
even or sloping terrain. Use a plumb
or level to determine the direction of
tree lean.
S Weight and branches on one side.
S Surrounding trees and obstacles.
S Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator.
STOPPING YOUR SAW
S Release the trigger switch.
S If motor does not stop, disconnect
the extension cord. Discontinue use
of the unit until it has been repaired
by an authorized service dealer.
STARTING YOUR SAW
S Connect the saw to a power source
using the proper size extension cord;
see SELECT AN EXTENSION CORD in
the OPERATION section).
S Grip both handles firmly.
S Push and hold the trigger lock--out
button with your right hand thumb.
S Squeeze and hold the trigger switch.
OPERATING TIPS
S Check chain tension before first use
and after 1 minute of operation. See
CHECK CHAIN TENSION in the SER-
VICE AND ADJUSTMENTS section.
S Cut wood only. Do not cut metal, plas-
tics, masonry, non-wood building ma-
terials, etc.
S Stop the saw if the chain strikes a for-
eign object. Inspect the saw and repair
parts as necessary.
S Keep the chain out of dirt and sand.
Even a small amount of dirt will quickly
dull a chain and increase the possibil-
ity of kickback.
S Practice cutting a few small logs using
the following steps. This will help you get
the “feel” of using your saw before you
begin a major sawing operation.
S Squeeze trigger switch and allow unit
to reach full speed before cutting.
S Begin cutting with the saw frame
against the log.
S Keep the motor at full speed the en-
tire time you are cutting.
S Release the trigger switch as soon
as the cut is completed, allowing the
motor to stop.
S Make sure there is enough room for
the tree to fall. Maintain a distance of
2-1/2 tree lengths from the nearest
person or other objects. Noise can
drown out a warning call.
S Remove dirt, stones, loose bark,
nails, staples, and wire from the tree
where cuts are to be made.
Plan a clear retreat path
Direction of Fall
45_
8
FELLING LARGE TREES
S As tree starts to fall, stop saw, put it
down, and get away quickly on your
planned retreat path.
(6 inches in diameter or larger)
The notch method is used to fell large
trees. A notch is cut on the side of the tree S DO NOT use your saw to cut down a par-
in the desired direction of fall. After a felling
cut is made on the opposite side of tree,
the tree will tend to fall in the direction of
the notch.
NOTE: If tree has large buttress roots,
remove them before making the notch. If
using saw to remove buttress roots,
keep saw chain from contacting ground
to prevent dulling of the chain.
tially fallen tree. Be extremely cautious
with partially fallen trees that may be
poorly supported. When a tree doesn’t
fall completely, set saw aside and pull
down tree with a cable winch, block and
tackle, or tractor.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a fall-
en tree to the desired log size.
NOTCH CUT AND FELLING TREE
S Make notch cut by cutting the top of
the notch first. Cut through 1/3 of the
diameter of the tree. Next complete
the notch by cutting the bottom. See il-
lustration. Once the notch is cut, re-
move the wedge of wood from tree.
WARNING: Do not stand on the
log being cut. Any portion can roll caus-
ing loss of footing and control. Do not
stand downhill of the log being cut.
Final cut here
IMPORTANT POINTS
S Cut only one log at a time.
S Cut shattered wood very carefully;
sharp pieces of wood could be flung
toward operator.
First cut
Notch
S Use a sawhorse to cutsmall logs. Nev-
er allow another person to hold the log
while cutting and never hold the log
with your leg or foot.
Hinge
Second cut
S Do not cut in an area where logs, limbs,
and roots are tangled. Drag logs into a
clear area before cutting them by pulling
out exposed and cleared logs first.
S After removing the wood from the notch,
make the felling cut on the opposite side
of the notch. This is done by making a
cut about two inches higher than the
center of the notch. This will leave
enough uncut wood between the felling
cut and the notch to form a hinge. This
hinge will help prevent the tree from fal-
ling in the wrong direction.
BUCKING TECHNIQUES
WARNING: If saw becomes
pinched or hung in a log, don’t try to force it
out. You can lose control of the saw result-
ing in injury and/or damage to the saw.
Stop the saw, drive a wedge of plastic or
wood into the cut until the saw can be re-
moved easily. Restart the saw and care-
fully reenter the cut. Do not use a metal
wedge. Do not attempt to restart your saw
when it is pinched or hung in a log.
Hinge holds tree on stump and
helps control fall.
Opening
of felling
cut
Use a wedge to remove pinched saw
Closing of
notch
NOTE: Before felling cut is complete,
use wedges to open the cut when
necessary to control the direction of fall.
To avoid kickback and chain damage,
use wood or plastic wedges, but never
steel or iron wedges.
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
S Be alert to signs that the tree is ready to Overcutting begins on the top side of the
fall: cracking sounds, widening of the log with the bottom of the saw against the
felling cut, or movement in the upper log. When overcutting use light downward
branches.
pressure.
9
st
Overcutting
Undercutting
1
Cut
nd
2
Cut
Undercutting involves cutting on the un-
derside of the log with top of saw against
the log. When undercutting use light up-
ward pressure. Hold saw firmly and main-
tain control. The saw will tend to push
back toward you.
nd
Using a support stand
2
Cut
WARNING: Never turn saw upside
down to undercut. The saw cannot be
controlled in this position.
st
1
Cut
Always make your first cut on the com-
pressions side of the log. The compres-
sion side of the log is where the pressure
of the log’s weight is concentrated.
st
1
Cut
nd
2
Cut
First cut on compression side of log
LIMBING AND PRUNING
Second cut
Second cut
WARNING: Be alert for and guard
against kickback. Do not allow the mov-
ing chain to contact any other branches
or objects at the nose of the guide bar
when limbing or pruning. Allowing such
contact can result in serious injury.
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
S Overcut through 1/3 of the diameter of
the log.
S Roll the log over and finish with a sec-
ond overcut.
WARNING: Never climb into a tree
to limb or prune. Do not stand on lad-
ders, platforms, a log, or in any position
which can cause you to lose your bal-
ance or control of the saw.
S Watch for logs with a compression
side to prevent the saw from pinching.
See illustration above for cutting logs
with a compression side.
BUCKING USING A LOG OR
SUPPORT STAND
IMPORTANT POINTS
S Watch out for spring poles. Spring
poles are small size limbs which can
whip toward you or pull you off bal-
ance. Use extreme caution when cut-
ting small size limbs.
S Remember your first cut is always on
the compression side of the log.
(Refer to the illustration below for your
first and second cut)
S Be alert for spring back from any
branches that are bent or under pres-
sure. Avoid being struck by thebranch
or the saw when the tension in the
wood fibers is released.
S Frequently clear branches out of the
way to avoid tripping over them.
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
LIMBING
Using a log for support
S Limb a tree only after it is cut down.
S Leave the larger limbs underneath the
felled tree to support the tree as you
work.
nd
2
Cut
S Start at the base of the felled tree and
work toward the top, cutting branches
and limbs. Remove small limbs with
one cut.
st
1
Cut
S Keep tree between you and the chain.
10
S Remove larger branches with the cut- S Finish the pruning operation by using
ting techniques described BUCKING
an overcut so that the stump of the
limb protrudes 1 to 2 inches (3--5 cm)
from the trunk of the tree.
Second cut
WITHOUT A SUPPORT.
S Always use an overcut to cut small
and freely hanging limbs. Undercut-
ting could cause limbs to fall and pinch
the saw.
PRUNING
First cut
WARNING: Limit pruning to limbs
shoulder height or below. Do not cut if
branches are higher than your shoulder.
Get a professional to do the job.
S Make your first cut 1/3 of the way
through the bottom of the limb. This
cut will make the limb sag so that it
falls easily on the second cut.
1/3 of way
3rd cut 1 to 2 in.
(3--5 cm) from
trunk of tree
S Next make a second cut all the way
through the limb.
MAINTENANCE
CUSTOMER RESPONSIBILITIES
WARNING: Disconnect power source before performing maintenance.
Fill in dates as you complete
regular service
Before
Use
After
Use
Every
15 min.
Service
Dates
Check for damaged/worn parts
n
Check for loose fasteners/parts
Check chain tension
n
n
n
Check chain sharpness
Check guide bar
n
n
Check bar and chain oil level
Lubricate bar sprocket hole
n
n
n
Inspect and clean unit & labels
Clean guide bar groove
n
GENERAL RECOMMENDATIONS
S Trigger Switch -- Ensure the trigger
switch functions properly by squeez-
ing and holding the trigger switch.
Make sure motor starts and stops.
The warranty on this unit does not cover
items that have been subjected to oper-
ator abuse or negligence. To receive full
value from the warranty, the operator S Oil Tank -- Discontinue use of chain
must maintain unit as instructed in this
manual. Various adjustments will need
saw if oil tank shows signs of damage
or leaks.
to be made periodically to properly S Extension Cord -- Discontinue use if
maintain your unit. Improper mainte-
nance may cause damage to the unit
and possible injury to the operator or by-
standers.
chain saw extension cord showssigns
of damage or wear.
CHECK FOR LOOSE FASTENERS
AND PARTS
S Bar Clamp Nuts
S Chain
S Bar Adjusting Screw
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for
replacement of worn or damaged parts.
NOTE: It is normal for a small amount of
oil to appear under the saw after motor
stops. Do not confuse this with a leaking
oil tank.
11
CHECK CHAIN TENSION
CHECK GUIDE BAR
Conditions which require guide bar main-
tenance:
WARNING:
Wear protective
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
S Inadequate supply of oil to the bar and
chain.
Check the condition of the guide bar each
time the chain is sharpened. A worn guide
bar will damage the chain and make cut-
ting difficult.
gloves when handling chain. The chain
is sharp and can cut you even when it is
not moving.
Chain tension is very important. Chain
stretches during use. This is especially
true during the first few times you use your
saw. Always check chain tension each
time you use your saw.
After each use, with unit disconnected
from power source, clean all sawdust from
the guide bar and sprocket hole.
To maintain guide bar:
S Disconnect the chain saw from the
power source.
D Unplug unit from the power source.
D Use a screwdriver to move chain
around guide bar to ensure kinks do not
exist. The chain should rotate freely.
S Loosen and remove bar mounting nuts.
Remove bar and chain from saw.
S Clean the oil holes and bar groove af-
ter each 5 hours of operation.
D Loosen bar clamp nuts until they are
finger tight against the bar clamp.
D Turn the adjusting screw clockwise until
the chain solidly contacts bottom of
guide bar rail. Then, turn adjusting
screw an additional 1/4 turn.
ve Sawdust From
de Bar Groove
Sprocket Hole
Oil Holes
Adjusting Screw -- 1/4 Turn
NOTE: To tighten the chain, turn the ad-
justing screw clockwise; to loosen the
chain, turn the adjusting screw counter-
clockwise.
S Add lubricant to sprocket hole after
each use.
S Burring of guide bar rails is a normal
process of rail wear. Remove these
burrs with a flat file.
S When rail top is uneven, use a flat file
to restore square edges and sides.
Adjusting Screw
File Rail Edges
and Sides
Square
Worn Groove
Correct Groove
D Check the tension by lifting the chain
from the guide bar. Remove some of the
stiffness in the chain by pulling down
and letting go of the chain several times.
D Continue turning the adjusting screw
until the tension is correct.
Replace the guide bar when the groove is
worn, the guide bar is bent or crack--ed, or
when excess heating or burring of the rails
occurs. If replacement is necessary, use
only the guide bar specified for your saw in
the repair parts list or on the decal located
on the chain saw.
D Tighten bar mounting nuts with a
wrench.
D Recheck chain tension.
LUBRICATION
WARNING: If the saw is operated
with a loose chain, the chain could jump
off the guide bar and result in serious in-
jury.
Bar Oil
Fill Cap
Bar
Sprocket
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A dull
chain makes a sawdust powder and
cuts slowly. See CHAIN SHARPENING in
the SERVICE AND ADJUSTMENTS
section.
12
S Check bar and chain oil before use INSPECT AND CLEAN UNIT AND
and every 15 minutes while operating LABELS
the saw. See GUIDE BAR AND CHAIN S After each use, inspect complete unit
OIL under the OPERATION section.
S Lubricate bar sprocket hole after each
use.
for loose or damaged parts. Clean the
unit and labels using a damp cloth with
a mild detergent.
S Wipe off the unit and labels with a
clean dry cloth.
SERVICE AND ADJUSTMENTS
CHAIN SHARPENING
S Turn the adjusting screw counter-
clockwise to move the adjusting pin al-
most as far as it will go to the rear. Do
not remove the adjusting screw from
the unit.
Chain sharpening requires special tools.
You can purchase sharpening tools at an
authorized service dealer or go to a pro-
fessional chain sharpener.
S Hold chain with cutters facing as
shown.
WARNING: Avoid accidental start-
ing. Always unplug saw from power
source before installing a bar and/or
chain.
Tip of
Bar
CHAIN REPLACEMENT
WARNING:
Wear protective
gloves when handling chain. The chain
is sharp and can cut you even when it is
not moving.
It is normal for a new chainto stretch dur-
ing the first 30 minutes of operation. You
should recheck your chain tension fre-
quently and adjust the chain tension as
required. See CHECK CHAIN TENSION
section.
CUTTERS MUST FACE IN
DIRECTION OF ROTATION
Depth Gauge
Cutters
Replace the old chain when it becomes
worn or damaged. Use only the Low
Kickback replacement chain specified
in the list of available replacement parts.
The chain must comply with kickback re-
quirements of ANSI B175.1 when tested
with this saw. See your authorized ser-
vice dealer to replace and sharpen indi-
vidual cutters on your chain.
Drive Links
S Place chain around the sprocket and
fit the drive links into the guide bar
groove and then around guide bar
nose.
TO REPLACE CHAIN:
D Disconnect the chain saw from the
power source.
Bar Nuts
Adjusting Screw
Bar
S Hold the guide bar against the saw
frame and install the bar clamp.
Be sure adjusting pin is in the adjust-
ing pin hole in the bar.
Clamp
S Remove bar mounting nuts, bar clamp
plate, and old chain.
13
CUSTOMER SERVICEABLE PARTS
WARNING: Use of any other ac-
cessory or attachment might present a
risk of injury to the operator.
Inside view of
Bar Clamp
Adjusting pin hole
REPLACEMENT PART
PART NO.
Hex Nuts
Oil Cap
Bar Adjusting Screw
Bar Adjusting Pin
File (5/32” dia.) Twin Pak
Xtra GUARDr Chain --14”
Xtra GUARDr Chain --16”
Lo--Kickr Guide Bar -- 14”
Lo--Kickr Guide Bar -- 16”
530015917
530053072
530016265
530053068
952055085
952051469
952051470
952044758
952044759
Adjusting
screw
Adjusting pin
S Secure the guide bar and bar clamp
plate with the bar nuts; tighten finger
tight only.
CAUTION: If saw chain is installed back-
wards, the saw will vibrate excessively
and will not cut wood.
CHAIN ADJUSTMENT
See CHECK CHAIN TENSION in the MAIN-
TENANCE section.
Bar & Chain Lubricant --1 qt 952030203
Bar & Chain Lubricant --1 gal 952030204
STORAGE
SEASONAL STORAGE
Prepare your unit for storage at the end of
the season or if it will not be used for 30
WARNING: Perform the following
steps after each use:
S Allow motor to cool before storing or days or more.
transporting.
If your chain saw is to be stored for a
S Store chain saw and extension cord in period of time:
a well ventilated area
S Clean it thoroughly before lengthy
storage.
S Store in a clean dry area.
S Lightly oil external metal surfaces and
guide bar.
S Store chain saw with all guards in
place and position chain saw so that
any sharp object cannot accidentally
cause injury.
S Store chain saw unplugged, well out of S Oil the chain and wrap it in heavy
the reach of children. paper or cloth.
14
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source be-
fore performing all of the recommended remedies below except remedies
that require unit to be operating.
TROUBLE
CAUSE
REMEDY
Chain does 1. Chain tension incorrect.
not move
1. See “Check Chain Tension” in
Maintenance section.
when trigger 2. Guide bar rails pinched.
2. Repair or replace.
switch is
engaged.
3. Trigger switch failure.
4. Circuit breaker tripped/
fuse failure.
3. Contact authorized service dealer.
4. Reset circuit breaker or replace
fuse.
1. See “Check Chain Tension” in
Maintenance Section.
2. Contact authorized service dealer.
3. Resharpen or replace chain.
4. See “Chain Sharpening” in
Service and Adjustments section.
1. Chain tension incorrect.
Chain clat-
ters or cuts
roughly.
2. Cutters damaged.
3. Chain worn.
4. Cutters dull, improperly
sharpened, or depth
gauges too high.
5. Contact authorized service dealer.
5. Sprocket worn.
Chain stops 1. Chain cutter tops not
1. See “Chain Sharpening” in
Service and Adjustments section.
2. Repair or replace guide bar.
during cut.
filed flat.
2. Guide bar burred or
bent; rails uneven.
Oil inade-
1. Oil tank empty.
2. Oil outlet clogged.
3. Guide bar oil hole
blocked.
1. Fill oil tank.
2. Contact authorized service dealer.
3. Remove bar and clean.
quate for bar
and chain
lubrication.
1. Cutters damaged on
one side.
2. Chain dull on one side. 2. See “Chain Sharpening” in
Service and Adjustments section.
1. See “Chain Sharpening” in
Service and Adjustments section.
Chain cuts
at an angle.
3. Guide bar bent or worn. 3. Replace guide bar.
If situations occur which are not covered in this manual, use care and good
judgement. If you need assistance, contact an authorized service dealer or call
1-800-554-6723.
15
WARRANTY STATEMENT
ELECTROLUX HOME PRODUCTS,
setup or normal adjustments explained in
INC., warrants to the original purchaser the instruction manual.
that each new Poulan brand electric or THIS WARRANTY GIVES YOU SPECIFIC LE-
cordless product is free from defects in GAL RIGHTS, AND YOU MAY HAVE OTHER
material and workmanship and agrees to RIGHTS WHICH VARY FROM STATE TO
repair or replace under this warranty any STATE.NO CLAIMS FOR CONSEQUENTIAL
defective Poulan brand electric product OR OTHER DAMAGES WILL BE ALLOWED,
within one (1) year from the original date of AND THERE ARE NO OTHER EXPRESS
purchase.
WARRANTIES EXCEPT THOSE EX-
If your Poulan brand electric or cordless PRESSLY STIPULATED HEREIN.
product should fail within the limited war- SOME STATES DO NOT ALLOW LIMITA-
ranty period, return it, complete, prepaid, TIONS ON HOW LONG AN IMPLIED WAR-
with proof of purchase, to the dealer from RANTY LASTS OR THE EXCLUSION OR
whom it was purchased for repair or re- LIMITATIONS OF INCIDENTAL OR CONSE-
placement at the option of ELECTRO- QUENTIAL DAMAGES, SO THE ABOVE LIMI-
LUX HOME PRODUCTS, INC.
TATIONS OR EXCLUSION MAY NOT APPLY
This warranty is not transferable and does TO YOU.
not cover damage or liability caused by The policy of ELECTROLUX HOME
improper handling, improper mainte- PRODUCTS, INC., is to continuously im-
nance or the use of accessories and/or at- prove its products. Therefore, ELECTRO-
tachments not specifically recommended LUX HOME PRODUCTS, INC., reserves
by ELECTROLUX HOME PRODUCTS,
the right to change, modify, or discontinue
INC., for this electric product. Additionally, models, designs, specifications, and ac-
this warranty does not cover parts that will cessories of all products at any time with-
wear and require replacement with rea- out notice or obligation to any purchaser.
sonable use during the warranty period.
This warranty does not cover pre--delivery
16
|