Premier Mounts TV Mount XUA 1330L User Manual

Included Hardware  
M4 x 12mm Phillips  
Head Screw  
(Qty 4)  
¾” Spacer (Qty 4)  
INSTALLATION GUIDE: XUA-1330L  
M4 x 30mm Phillips  
Head Screw  
(Qty 4)  
Victory LCD Wall Mounting System  
2” Wood Screw  
(Qty 2)  
The Victory LCD Mounting System is designed for secure installation of LCD displays of up to  
40 lbs. in weight.  
Bubble Level (Qty 1)  
Tool List  
Warning Statements  
Phillips Head Screw Driver  
Electronic Stud Finder  
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MAXIMUM  
WEIGHT OF 40 LBS. IF NOT, THE WALL MUST BE REINFORCED. PROPER  
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN  
THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO  
COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH.  
WARNING:  
Allen Wrenches (3mm and 4mm – supplied)  
Portable Drill  
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION  
OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION  
PROCEDURE TO PREVENT PERSONAL INJURY.  
WARNING:  
WARNING:  
¼” Masonry Bit for Concrete Installation  
NOTE: The included level may be permanently attached to the  
wall plate by inserting the level into the receptacle on  
the back of the wall plate.  
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS  
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION  
INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY  
DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE  
LOCATION FOR FUTURE REFERENCE.  
Wood Stud Installation  
NOTE:  
Using a wood stud finder, locate the stud centers  
behind the wall. Once found, make a pencil marking  
on the center of the wood studs. Once the mark is  
made, it is strongly recommended that a pilot hole be  
drilled with a 1/8” drill bit.  
A secure structure must support the weight or load of the display. When mounting to a wall that  
contains wooden studs, dead center of the wooden stud must be confirmed prior to installation.  
1. Place the back plate against the wall with the hook towards  
the bottom.  
2. Secure the back plate using one (1) 2” wood screw.  
3. Using the integrated bubble guide, carefully adjust the back  
plate until it is level.  
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to  
do so could result in damage to the display and/or damage to the mounting surface.  
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct  
heat energy. Failure to do so may result in damage to the display and could increase the risk of  
fire.  
4. Attach the remaining 2” wood screw into the back plate and  
tighten.  
At least two qualified people should perform the installation procedure. Injury and/or damage  
can result from dropping or mishandling the display.  
Concrete Installation  
NOTE: ¼” x 2 ¼” Threshold anchors must be used for concrete  
installation. They can be purchased at your local  
hardware store.  
1. Place the back plate against the wall with the hook towards  
the bottom.  
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be  
installed on any surface other than wooden studs, use suitable hardware (which is  
commercially available).  
2. Level and mark with a pencil the two mounting points found  
on the back plate.  
Contact Victory Mounts with any technical / installation questions.  
3. Next, drill two holes using an electric drill and ¼” masonry bit.  
4. Insert the threshold anchors into the holes that were drilled in  
the wall.  
NOTE: If necessary, use a hammer to lightly tap each anchor  
into place so that they are flush with the wall. Once  
mounted in the wall, unscrew the slotted cap off of  
the threshold screw.  
Threshold  
Anchor  
5. Once the anchors are in place, set the back plate back over  
the concrete anchors.  
6. Using a Slot Head screw driver, attach the back plate by  
threading the two slotted caps onto the threaded insert that  
is recessed into the wall.  
7. Make sure all screws are snug, but be careful not to over-  
tighten them.  
Slotted Cap  
Threaded Insert  
Threshold Anchor  
 

Peavey Microphone LX 20 User Manual
Peavey Musical Instrument Amplifier Mark VI User Manual
Peavey Portable Speaker Impulse 100 User Manual
Philips Bottle Warmer SCF123 17 User Manual
Philips MP3 Docking Station AJ7041D User Manual
Philips Water Heater AZ 9213 User Manual
Polk Audio Speaker PSW10 User Manual
Poulan Chainsaw 530088740 User Manual
Premier Mounts Projector Accessories PDS 017 User Manual
Primera Technology Printer Conductor Printer User Manual