Pride Mobility Network Card Dynamic DX User Manual

Dynamic DX  
Specialty Controls Remote  
(SCR)  
Basic Operation Instructions  
 
SCR  
Basic Operation Manual  
3
TABLE OF CONTENTS  
INTRODUCTION ................................................................................ 4  
Dynamic DX Specialty Controls Remote (SCR)....................................... 4  
SCR CONTROLS ................................................................................ 6  
STANDARD MODE CONFIGURATION...................................... 6  
Driving in Standard Mode Configuration .................................................. 6  
TIMEOUT FUNCTION...................................................................... 7  
SEAT CONTROL................................................................................. 7  
Tilt Mode ................................................................................................... 7  
Recline Mode............................................................................................. 8  
Left Leg Rest Mode ................................................................................... 8  
Right Leg Rest Mode................................................................................. 9  
 
4
Basic Operation Manual  
SCR  
INTRODUCTION  
Welcome to Quantum Rehab, a Division of Pride Mobility Products  
Corporation. Quantum Rehab is dedicated to the customization of power  
chairs for users with advanced rehabilitation and mobility issues. Quantum  
Rehab also expands possibilities for enhanced healthcare attendant control  
over power chair functions to provide a secondary level of support for our  
customers where necessary.  
The Dynamic DX Specialty Controls Remote (SCR)  
The Dynamic DX Specialty Controls Remote (SCR) allows users to control  
a wide range of on-chair and off-chair functions. SCR units come pre-  
programmed in the Standard Mode Configuration explained in this manual,  
but are not limited to it. Please contact your authorized provider for more  
information on programming alternatives.  
The SCR is used in conjunction with input devices such as joysticks, touch  
pads, lap trays, head arrays, Buddy Buttons, Sip-N-Puff systems, etc. The  
purpose of the SCR is to enhance and expand input device function, so that  
the user can do more with his/her power chair.  
This manual is designed to explain basic operation for the following functions:  
1. SCR Controls  
- Utilizes the On/Off Switch and the Mode Switch to power the SCR and  
choose pre-programmed functions.  
2. Standard Mode Configuration  
-Allows the user to choose and control the driving speed of his/her power  
chair using one of five modes.  
3. Timeout Function  
- This is a safety feature built in to the programming of the SCR.  
4. Seat Control  
- Allows the user to control seat actuator adjustment.  
 
SCR  
Basic Operation Manual  
5
Figure 1 provides information on the SCR components and connections.  
Use this diagram to familiarize yourself with the function and location of  
each component before using the SCR.  
Reverse Indicator  
Disregard - this is a non-  
functioning feature.  
LCD Display  
4-line, 20 character  
backlit LCD which  
shows all functions  
and instructions.  
Battery Meter  
Battery charge level  
is indicated by a  
set of six LEDs.  
Mode Switch  
Cycles through the  
programmed modes.  
On/Off Switch  
Toggles the entire DX  
control system between  
the On & Off modes.  
HHP/Wizard Port  
Allows connection to an IBM  
computer for custom  
programming and where  
standard drive programming  
occurs with the HHP.  
External Switch Jacks  
Three 3.5 mm (1/8") jack  
sockets to allow connection of  
external switches  
Battery Charger Port  
Standard 3-pin XLR type  
battery charger socket used  
with off-board charging  
systems.  
DXBUS Socket  
For connecting the DX Remote  
with a DXBUS cable to other  
DX compatible modules  
Figure 1. SCR Components and Connections  
 
6
Basic Operation Manual  
SCR  
SCR CONTROLS  
The SCR has only two built-in controls: the On/Off Switch and the Mode  
Switch (see figure 1). The On/Off Switch simply controls power to the SCR.  
The Mode Switch cycles the SCR through eight possible program modes.  
Only five of the eight possible program modes are used in the Standard Mode  
Configuration.All five program modes are Drive Modes (see Standard Mode  
Configuration).  
STANDARD MODE CONFIGURATION  
Quantum Rehab’s Standard Mode Configuration for the SCR encompasses  
five drive programs, all of which control driving speed as a percentage of  
maximum speed. The slowest is Drive Mode 1; the fastest is Drive Mode 5.  
Actual maximum speed varies according to the power chair model.  
Driving in Standard Mode Configuration  
Driving in Standard Mode Configuration is simple. Power up the SCR using  
the On/Off Switch (either onboard or plugged into the external On/Off Switch  
jack). The LCD Display will show Drive Mode 1 and prompt the user to  
select one of three options (see figure 2):  
1. Previous (down arrow)  
-Returns the SCR to the previous  
state (in this case, powered  
down)  
DRIVE MODE 1  
YES  
NEXT  
PREVIOUS  
2. Yes (right arrow)  
-Selects Drive Program 1  
3. Next (up arrow)  
-Selects the next option (in this  
case, Drive Program 2)  
Figure 2. Drive Program Selection  
Using the input device, select the drive program most appropriate to the  
current environment, e.g., indoor setting versus outdoor setting. Choosing  
the “Next” command will cycle the SCR through the drive programs. The  
LCD display will change with each option selection.  
 
SCR  
Basic Operation Manual  
7
TIMEOUT FUNCTION  
The timeout function is a safety feature in the nature of an “automatic sleep”  
mode. When the SCR is powered up, the user has ten seconds to begin driving  
the power chair. If the user begins driving the power chair within ten seconds  
of power up, the timeout function is suspended until the unit is stationary  
again. If the user does not begin driving the power chair within ten seconds  
of power up, the timeout function automatically exits to the Main Screen  
Display.  
SEAT CONTROL  
Executing a “Next” command with the input device when in Drive Mode 5  
moves the SCR to the Seat Control Menu. See figure 3. To enter the Seat  
Control Mode, choose the “Yes” option. In this mode, the user can control  
the adjustment of the available seat actuators, including Tilt, Recline, Left  
Leg Rest, and Right Leg Rest. Each  
mode will prompt the user to  
choose one of four options (see  
figures 4-7):  
SEAT CONTROL  
YES  
NEXT  
PREVIOUS  
Tilt Mode  
1. Down (up arrow)  
-Returns the seat to an upright  
position.  
2. Up (down arrow)  
Figure 3. Seat Control Selection  
-Adjusts the actuator to the  
desired tilted position.  
SEAT CONTROL  
TILT  
3. Exit (left arrow)  
-Returns the SCR to the Seat  
Control Menu  
DOWN  
EXIT  
UP  
NEXT  
4. Next (right arrow)  
-Moves the SCR to the next  
actuator option.  
Figure 4. Tilt Mode Selection  
 
8
Basic Operation Manual  
SCR  
Recline Mode  
1. Up (up arrow)  
-Returns the seat to an upright  
position.  
SEAT CONTROL  
RECLINE  
UP  
PREVIOUS  
RECLINE  
NEXT  
2. Recline (down arrow)  
-Adjusts the seat to the desired  
position.  
3. Previous (left arrow)  
-Returns the SCR to the previous  
actuator option.  
Figure 5. Recline Mode Selection  
4. Next (right arrow)  
-Moves the SCR to the next  
actuator option.  
Left Leg Rest Mode  
1. Down (up arrow)  
-Lowers the leg rest.  
SEAT CONTROL  
LEFT LEG  
DOWN  
UP  
NEXT  
PREVIOUS  
2. Up (down arrow)  
-Raises the leg rest.  
3. Previous (left arrow)  
-Returns the SCR to the previous  
actuator option.  
Figure 6. Left Leg Rest Mode  
Selection  
4. Next (right arrow)  
-Moves the SCR to the next  
actuator option.  
 
SCR  
Basic Operation Manual  
9
Right Leg Rest Mode  
1. Down (up arrow)  
-Lowers the leg rest.  
SEAT CONTROL  
RIGHT LEG  
DOWN  
UP  
EXIT  
PREVIOUS  
2. Up (down arrow)  
-Raises the leg rest.  
3. Previous (left arrow)  
-Returns the SCR to the previous  
actuator option.  
Figure 7. Right Leg Rest Mode  
Selection  
4. Exit (right arrow)  
-Moves the SCR to the next  
available menu.  
 
10  
Basic Operation Manual  
SCR  
NOTES  
 
SCR  
Basic Operation Manual  
11  
NOTES  
 
Exeter, PA  
Quantum Hotline: 1-866-800-2002  
Visit the Rehab Zone at:  
INFMANU1746/A/MAY 2001  
 

Philips Computer Keyboard FCV 552 User Manual
Philips Digital Photo Frame 25SL5766 User Manual
Philips Indoor Furnishings SBC VS010 User Manual
Philips Network Router SYK5600 User Manual
Philips Sprinkler PM3350 User Manual
Philips Stereo Amplifier TDA6107AJF User Manual
Philips TV VCR Combo 25PV707 User Manual
Planar Marine Lighting PUD3200 User Manual
Polaris Offroad Vehicle 120 User Manual
Polycom Telephone 8012S User Manual