ProMaster Camcorder Accessories 2437 User Manual

Variable Color Temperature  
 
Using the Light  
Your PROMASTER VARI-TEMP LED light uses a combination of daylight and 3200º K super bright  
LEDs to adjust the color temperature of your light to the surrounding ambient light conditions.  
Matching the color temperature of the existing light allows you to add light to get better exposures  
while maintaining the natural feel of your scene.  
1. Press and hold the Power/Mode button (3) for approximately 3 seconds to turn on the light. The  
battery indicator lights will come on to indicate the remaining battery power. To turn the light off,  
press and hold the Power/Mode button for approximately 3 seconds until the light turns off.  
2. Select a mode by pressing the mode switch. Continue to press the mode switch to cycle through  
each mode and choose your desired setting:  
Modes: Constant light (default), Fast Flash, SOS (International distress signal), Slow Flash  
3. Adjust the light to the desired level of color and brightness using the adjustment buttons (2). The  
UP▲ and DOWN▼ buttons increase (UP) or decrease (DOWN) the brightness of the yellow  
light. The LEFT◄ and RIGHT► buttons increase (LEFT) or decrease (RIGHT) the brightness of  
the white light. Use these controls together to control the color temperature and the overall  
intensity of the light.  
Note:  
1. As the battery gets weaker, the light output will be reduced. Please be sure to use a fully charged  
battery and in order to maintain the maximum output of the light, replace the battery when the  
power level is low.  
2. After use be sure to set the power switch to “OFF”.  
3. When not in use, remove the battery and store in a cool dry location.  
4. Before storing the light, be sure it is cool to the touch. Storing a hot light could cause fire.  
Remote Control  
The supplied MR6 remote control can control all of the functions on the light as  
well as the shutter release function of CANON, NIKON, SONY, PENTAX, and  
KONICA/MINOLTA cameras that support an infrared remote.  
1. The light has infrared receivers on both the front and rear panel of the light  
(11, 12). To operate the light, point the remote control in the direction of the  
light. Press:  
ON To turn the light on  
OFF To turn the light off  
M To cycle through the operation modes of the light  
▲ or ▼ - To control the intensity of the yellow light  
or - To control the intensity of the white light  
2. To use the remote as a shutter release:  
CANON Press the S button next to the Canon name to release the shutter immediately. Press  
the 2S button to release the shutter after a 2 second delay. In the autofocus mode on Canon  
cameras the shutter will not release unless the camera has achieved proper focus. The 2S mode  
allows time for certain slower focusing lenses to achieve focus.  
NIKON Press the S button next to the Nikon name to release the shutter immediately.  
PENTAX Press the S button next to the P name to release the shutter. The W/T button may be  
used to control the zoom on some Pentax models.  
SONY, KONICA/MINOLTA Press the S button next to the KM name to release the shutter  
immediately. Press the 2S button to release the shutter after a 2 second delay.  
 
Note: The working distance of an infrared signal can vary dramatically. Bright light, obstructions  
between the remote and the device, weak batteries and other factors may impact the reliability of  
remote operation.  
Charging the battery  
Your LED336 light includes a battery and charger. To charge the battery:  
1. Align the contacts of the battery with the battery charging contacts on the charger. Gently slide  
the battery onto the charger until you hear a slight click. The battery will be locked into place.  
2. To remove the battery, press down on the lock tab at the end of the battery and slide the battery  
away from the charger.  
3. Plug the charger into an A/C power source. The charge indicator will glow red.  
4. When the battery is fully charged, the battery indicator will glow green (approximately 4 hours).  
WARNING: Only use the battery type specified for this charger. Using an incompatible battery  
may cause fire, explosion, or personal injury.  
Safety Tips  
To prevent any damage to your product or personal injury, please read the following safety  
precautions before operation.  
1. To prevent the risk of fire or electric shock, do not expose this device to rain or moisture.  
2. Use of incorrect battery or power supply may cause this unit to be damaged or become  
inoperable. Please note the correct operating voltage before use.  
3. If this unit emits smoke or a strange odor, disconnect the power immediately to prevent further  
damage to the equipment or personal injury.  
4. Do not disassemble this product. If the equipment is dropped or damaged by other means,  
please disconnect the power and return it to your dealer for service.  
5. Remove the battery and power supply for storage and transportation. Leaving the battery or  
power supply attached for long periods of time without use may cause fire or other unsafe  
conditions.  
6. Keep out of reach of children. This is not a toy and may cause injury if handled improperly.  
7. Be sure to observe all instructions for proper use of the battery and charger. Improper operation  
may cause the battery to leak or burst.  
8. Do not disassemble or short circuit the battery. Do not expose the battery to flame or excessive  
heat. Do not immerse the battery in water or other fluids. All of these actions can cause fire,  
explosion, or personal injury.  
9. This light is very bright. Avoid staring at the light when it is on. Lengthy exposure to the eyes  
could cause vision impairment.  
10. Do not cover the ventilation grille, which could cause excessive heat build up inside the light and  
cause damage.  
11. Do not expose the light to water or other liquids, which could cause a short circuit and damage  
the light.  
12. Avoid placing the light near alcohol, gasoline, or other flammable or volatile solvents which could  
cause fire or damage to the light.  
13. Do not pick up your camera by the light when it is attached. This could cause damage to the light  
and/or your camera.  
 
Cleaning  
1. To clean the light, use a damp cloth. Be sure to completely dry the light after cleaning.  
2. Do not use strong detergents, such as thinner, gasoline or alcohol, which could damage the  
protective layer of the lamp housing.  
Specifications  
20W Total -10W at full  
Working Voltage  
Average LED Life  
Luminance  
6v-9v  
Output Power  
white or full yellow  
50000 hours  
2180LUX  
Color Temperature 3200~6000K  
Illumination angle  
60°  
336pcs  
168 daylight 168  
yellow  
Working Distance  
Size  
Up to 26’/8m  
LED Quantity  
DC Input  
7 7/16 x 7 x 1 ¼" /  
188 x 178 x 32mm  
9V~16.8V  
Compatible Batteries  
Sony type NP-F, NP-FM, NP-QM series battery  
Code 2437  
Made in China  
Keep in Touch  
For more information, tutorials, industry news and tips & tricks, make sure to visit us at  
promaster.com, follow our feeds on Twitter @promasterphoto, and subscribe to our YouTube  
ProMaster Channel.  
One-Year Unconditional Guarantee  
If for any reason, this ProMaster product fails within ONE YEAR of the date of purchase, return this  
product to your ProMaster dealer and it will be exchanged for you at no charge. ProMaster products  
are guaranteed for ONE FULL YEAR against defects in workmanship and materials. If at any time  
after one year, your ProMaster product fails under normal use, we invite you to return it to ProMaster  
for evaluation.  
 

Paxar Printer Sierra Sport2 User Manual
Peg Perego Bouncy Seat FINA0601I60 User Manual
Pelco Recording Equipment RMA13 User Manual
Pelco Security Camera C2423M User Manual
Pelican Home Safety Product StealthLite2400 User Manual
Philips Network Card US2 P72069 User Manual
Pioneer Cassette Player KEH P4020R User Manual
Pioneer Stereo Receiver VSX 1020 User Manual
Polaroid Projector PV330 User Manual
Polycom IP Phone IP3000 3COM User Manual