ProMounts TV Mount UAPRO210 User Manual

User’s Manual UA-PRO210  
Supports up to 100 lbs / 45 kg  
Included Mounting Hardware  
You Will Need  
1 UA-PRO210 mount  
(x1)  
A Level  
B Stud Finder  
C Marker  
D Drill  
E 3/16” or 3/8” drill bit  
F Hammer  
2 M4, M5 & M6 x 10 bolts (x4)  
3 M4, M5 & M6 x 12 bolts (x4)  
4 M4, M5 & M6 x 25 bolts (x4)  
5 M4, M5 & M6 x 40 bolts (x4)  
6 5/16” x 3” lag bolts  
7 Concrete anchors  
8 Ø 10 washers  
(x2)  
(x2)  
(x2)  
400 mm VESA  
extension (x4)  
9 Square washers  
5 & 6 mm hex key  
To reach  
400x400 mm  
use extensions  
Arm  
Cable Cover  
Wall Bracket  
End Cover  
Tilt  
Cover  
Bracket  
vBar  
 
INSTALLATION UA-PRO210  
1
Step 1:  
Separate arm from display bracket:  
1.1 Dissassemble tilt mechanism  
by loosening top bolts (A) and  
removing lower bolts (B).  
1.2 Pull up and away the display  
bracket from the arm.  
A
B
A
B
Step 2:  
Mount TV on display bracket:  
2.1 Loosen 4 adaptor plate bolts  
(C) so both VBars (D) can slide.  
2.2 Slide Vbars to match mounting  
holes on TV.  
2
2.3 Insert matching TV bolts (E)  
and tighten slightly.  
2.4 Tighten adaptor plate bolts (D)  
2.5 Re-assemble tilt mechanism.  
C
D
E
 
INSTALLATION (2) UA-PRO210  
Step 3:  
a) Mounting to a wood stud:  
3.0a Locate the wood stud.  
3.1a Place the mount to a suitable  
location and height.  
3
3.2a Using a bubble level, hold the  
mount in a level position and mark  
the holes position.  
3.3a Drill 3/16” holes.  
b) Mounting to a masonry wall:  
3.1b Place the mount to a suitable  
location and height.  
G
F
3.2b Using a bubble level, hold the  
mount in a level position and mark  
the holes position.  
3.3b Drill 3/8” holes, insert the  
wall anchor and tap them flush to  
the wall with a hammer.  
3.4 Attach the mount to the wall  
with the lag bolts (F) and steel  
washers (G) supplied.  
3.5 While the lag bolts are still  
slightly loose, check to make sure  
that the mounting plate is vertical.  
Adjust if necessary. Covered with  
the supplied molded caps.  
4
A
B
Step 4:  
Reattach tilt mechanism:  
4.1 Put back the display bracket on  
the arm hanging on left bolts (A).  
4.2 Put back removed bolts (B).  
4.3 Leave bolts (A and B) while  
adjusting tilt angle.  
4.4 Tighten at desired position.  
4.5 If necessary, adjust horizon  
with bolts (H).  
A
B
H
 
INSTALLATION (3) UA-PRO210  
Step 5:  
Cable Management:  
5.1 To install the cable, first you  
5
need to remove the end cover (I)  
and slide the cable cover (J) out  
from the arm.  
5.2 Do the same for the rest of the  
cable covers before installing the  
cables.  
5.3 Install the cables and slide the  
covers back to the arm.  
5.4 Install the end covers.  
I
A
B
J
Step 6:  
Adjusting the Display:  
6
6.1 Slight loosen Bolt (A); do not  
loosen fully or remove it, otherwise  
injury may occur.  
6.2 Grasp the upper and lower  
edge of the Display, and then push  
or pull the Display to the  
desired tilt angle.  
A
B
H
6.3 Tighten Bolt (A).  
6.4 If necessary, adjust horizon  
with bolts (H), as in step 4.5.  
FOR MORE INFORMATION VISIT  
ProMountsTM name, logo and model numbers are property of ProMounts.  
© ProMountsTM 2010  
 

Peavey Musical Instrument Amplifier 810 TX User Manual
Philips Cordless Telephone vox 300 User Manual
Philips Flat Panel Television 14PT135A 10 User Manual
Philips Projection Television 55PL9774 User Manual
Pioneer Car Video System AVH P4100DVD User Manual
Pioneer Stereo Receiver VSX AX5i G User Manual
Pioneer Stereo Receiver VSX D638 G User Manual
Planet Technology Network Card WGSW 2403 User Manual
Powermatic Sander WB 25 User Manual
ProForm Home Gym PFEVEX34181 User Manual