Your new PYLE HOME PCM Amplifier
gives you the power and versatility you need in a professional sound system.
The wide frequency response of it handles easily amplification of voice and music.
The monitor terminal, talkover function on MIC 1, and Tel/Paging make it perfectly to
use in meeting halls, auditoriums, sports events in school, and paging system in offices
, anywhere you need to deliver special announcement with excellent sound.
FEATURES AND CONTROLS
Pyle Home PCM30A Manual - 2
FEATURES AND CONTROLS
3 - Pyle Home PCM30A Manual
SPEAKER CONNECTION
One or more speakers (4, 8 or 16 Ohms) can be connected to the amplifier with or
without transformers. However, before you connect any speakers to the amplifier, the
total impedance must be calculated in order to avoid damage to the amplifier. A total
speaker impedance greater than 16 Ohms or less than 4 Ohms can cause this damage
to occur.
SYSTEM 1 : Single Speaker System
NOTE : Connect the speaker (+) to the amplifier's 4-Ohm, 8-Ohm or 16-Ohm terminal,
depending on the speaker being used.
SYSTEM 2 : Two (or more) Speakers in Series
NOTE : Connect the speaker (+) to the amplifier's 4-Ohm, 8-Ohm or 16-Ohm terminal,
depending on the TOTAL IMPEDANCE of the two speakers. If each speaker
has an impedance of 8-Ohm, the total speaker impedance in this series
cofiguration is 16 ohms.
Pyle Home PCM30A Manual - 4
SYSTEM 3 : Two (or more) Speakers in Parallel
NOTE : Connect the speaker (+) to the amplifier's 4-Ohm, 8-Ohm or 16-Ohm terminal,
depending on the TOTAL IMPEDANCE of the two speakers. If each speaker
has an impedance of 8-Ohm, the total speaker impedance in this series
configuration is 4 ohms.
SYSTEM 4 : Four Speakers in Series and Parallel
NOTE : Although the description above is for connecting two series pairs of 8 Ohms
speakers in a parallel hook up, you may also select to combine a series pair and
a parallel pair in a parallel hook up, simply be sure you have calculated the total
impedance, and attach the speaker (+) circuit wire to the proper amp terminal.
SYSTEM 5 : Connecting Speakers with Transformers
NOTE : When the 25V or 70V constant line voltages are used, a line matching transformer
must be used with each speaker, All transformers must be connected in parallel,
never connect line transformers in series.
5 - Pyle Home PCM30A Manual
CONNECTION DIAGRAM
Your Pyle Home Amplifier is an
example of superior design and
Pyle Home PCM30A Manual - 6
Specifications
Input Impedance
AUX...................................200mV/50k-Ohm, Unbalanced
MIC 1/MIC 2...........................1.0mV/600-Ohm, Balanced
TEL/PAGE ............................100mV/600-Ohm, Balanced
Max Output Power.........................................60 Watts x 1
THD at rated output power..................1% or less at 1 kHz
Frequency Response +/- 3 dB..................50 Hz to 15 kHz
Signal to Noise Ratio A-Weighted
MIC..........................................................................55dB
AUX..........................................................................70dB
TEL..........................................................................60dB
Speaker Outputs........................4-Ohm, 8-Ohm, 16-Ohm,
25V, and 70V line outputs
Monitor (MOH) Output.............600-Ohm 1V (head phones)
and 8-Ohm 1W (speaker)
Mute Level (AUX/MIC 2)............................................40dB
Tone Controls
Treble....................................................+/- 10dB, 10 kHz
Bass......................................................+/- 10dB, 100 Hz
Power Requirement............120V AC 60Hz/230V AC 50Hz
Power Fuse.........................T 2AL 250V for 110-120V and
T 1AL 250V for 220-240V
Dimensions, inches (mm) WxHxD..........10.7 x 3.46 x 8.86
(272 x 88 x 225)
Weight, lbs (kg) ...............................................9.79 ( 4.44)
Specifications are typical; individual units might vary.
Specifications are subject to change and improvement without notice.
7 - Pyle Home PCM30A Manual
|