Your new PYLE HOME PCM Amplifier
gives you the power and versatility you need in a professional sound system. The
wide frequency response of it handles easily amplification of voice and music. The
monitor terminal, talkover function on MIC 1, AUX output for extra amp connection,
and Tel/Paging make it perfectly to use in meeting halls, auditoriums, sports events
in school, and paging system in offices, anywhere you need to deliver special
announcement with excellent sound.
FEATURES AND CONTROLS
Pyle Home PCM60A Manual - 2
FEATURES AND CONTROLS
The input impedance of the
device should be more than 600 Ohms.
3 - Pyle Home PCM60A Manual
SPEAKER CONNECTION
One or more speakers (4, 8 or 16 Ohms) can be connected to the amplifier with or
without transformers. However, before you connect any speakers to the amplifier, the
total impedance must be calculated in order to avoid damage to the amplifier. A total
speaker impedance greater than 16 Ohms or less than 4 Ohms can cause this damage
to occur.
SYSTEM 1 : Single Speaker System
NOTE : Connect the speaker (+) to the amplifier's 4-Ohm, 8-Ohm or 16-Ohm terminal,
depending on the speaker being used.
SYSTEM 2 : Two (or more) Speakers in Series
NOTE : Connect the speaker (+) to the amplifier's 4-Ohm, 8-Ohm or 16-Ohm terminal,
depending on the TOTAL IMPEDANCE of the two speakers. If each speaker
has an impedance of 8-Ohm, the total speaker impedance in this series
cofiguration is 16 ohms.
Pyle Home PCM60A Manual - 4
SYSTEM 3 : Two (or more) Speakers in Parallel
NOTE : Connect the speaker (+) to the amplifier's 4-Ohm, 8-Ohm or 16-Ohm terminal,
depending on the TOTAL IMPEDANCE of the two speakers. If each speaker
has an impedance of 8-Ohm, the total speaker impedance in this series
configuration is 4 ohms.
SYSTEM 4 : Four Speakers in Series and Parallel
NOTE : Although the description above is for connecting two series pairs of 8 Ohms
speakers in a parallel hook up, you may also select to combine a series pair and
a parallel pair in a parallel hook up, simply be sure you have calculated the total
impedance, and attach the speaker (+) circuit wire to the proper amp terminal.
SYSTEM 5 : Connecting Speakers with Transformers
NOTE : When the 25V or 70V constant line voltages are used, a line matching transformer
must be used with each speaker, All transformers must be connected in parallel,
never connect line transformers in series.
5 - Pyle Home PCM60A Manual
CONNECTION DIAGRAM
NOTE : Unit comes with jumper set on AUX 1
NOTE : The unit provides a Phantom Power DC 15V for
electric condenser microphone, unit comes with
jumper set to Phantom Power enable ON.
WARNING:
These adjustments are to be
performed safely by the qualified
service technician in proper
operating condition, the AC
power source must be
disconnected before removing
the unit's cover, otherwise may
result in electric shock, or other
hazards.
Pyle Home PCM60A Manual - 6
Specifications
Input Impedance
AUX 1/AUX 2/AUX 3...........200mV/50k-Ohm, Unbalanced
MIC 1/MIC 2/MIC 3.................1.0mV/600-Ohm, Balanced
TEL/PAGE .............................100mV/600-Ohm, Balanced
Max Output Power.......................................100 Watts x 1
THD at rated output power..................1% or less at 1 kHz
Frequency Response +/- 3 dB................. 50 Hz to 15 kHz
Signal to Noise Ratio A-Weighted
MIC..........................................................................60dB
AUX..........................................................................70dB
TEL...........................................................................60dB
Speaker Outputs........................4-Ohm, 8-Ohm, 16-Ohm,
25V, and 70V line outputs
AUX Output...................................................600-Ohm 1V
Monitor (MOH) Output............600-Ohm 1V (head phones)
and 8-Ohm 1W (speaker)
Attenuation Level (AUX 1/AUX 2/AUX 3/MIC 2/MIC 3)...40dB
Tone Controls
Treble....................................................+/- 10dB, 10 kHz
Bass......................................................+/- 10dB, 100 Hz
Power Requirement............120V AC 60Hz/230V AC 50Hz
Power Fuse......................T 2.5AL 250V for 110-120V and
T 1.2AL 250V for 220-240V
Dimensions, inches (mm) WxHxD.......16.93 x 3.46 x 10.51
(430 x 88 x 267)
Weight, lbs (kg) ...............................................14.88(6.75)
Specifications are typical; individual units might vary.
Specifications are subject to change and improvement without notice.
Your Pyle Home Amplifier is an
example of superior design and
7 - Pyle Home PCM60A Manual
|