v1.0 (1.0.1.0) (EN/F)
user manual
guide de l’utilisateur
RC170i
EN/F
It is important to read this user manual prior to using your new product for the first time.
Nous vous recommandons de lire ce manuel avant d’utiliser votre nouveau produit
pour la première fois.
Before you begin
This Class B digital apparatus
complies with Canadian ICES-003.
Cet appareil numérique de la classe
B est conforme à la norme NMB-003
du Canada.
To install or replace the batteries:
1. Remove battery compartment door
(located at the bottom of the radio)
by applying thumb pressure to the
tab on battery door and then lift
the door out and off the cabinet.
The first time you dock your iPhone
or iPod touch, you’ll be prompted
to download the free RCA N-hance
App from the iTunes store. You are
encouraged to download and install this
app (right on your iPhone or iTouch)
in order to enjoy the wide variety
of features which are available with
N-hance. Instructions on how to use the
N-hance App can be found in the About
section inside the app.
Plugging in for power
•
Connect the supplied power adapter
to the unit’s DC jack, and connect to
a convenient wall outlet.
•
Refer to the “Clock” section and
follow the instructions to set the
clock time.
Electrical power
2. Insert or replace 2 AA batteries.
3. Replace the compartment door.
information
AC/DC adapter:
Battery back-up operation
Input: 100 - 240 V AC, 50/60 Hz
Output: 8 V DC, 2.2A
•
•
•
•
This clock radio is equipped with
a timekeeping system that is
powered with 2 “AA” batteries
(not included). The power failure
protection circuit will not operate
unless batteries are installed.
When normal household power
is interrupted, or AC line cord
is unplugged, the batteries will
power the clock radio to keep
track of time and alarm settings
programmed into memory.
When battery backup is operating
during a power interruption, the
clock display will not light, however
the alarm will function at the set
time as long as the remaining
battery power is adequate.
•
It is recommended to
replace the batteries at
least once per year even if
no power failures have occurred.
It is recommended to plug
the unit for AC power while
replacing batteries to avoid the
loss of clock and wake time/
mode settings.
•
•
App is for iPhone/iPod
touch only (iOS 3.2 or
higher).
“Made for iPod” and “Made for
iPhone” mean that an electronic
accessory has been designed to
connect specifically to iPod or iPhone,
respectively, and has been certified
by the developer to meet Apple
performance standards. Apple is not
responsible for the operation of this
device or its compliance with safety and
regulatory standards.
•
Note the N-hance App must be
running in order for the dock
to properly sync to your iPhone
or iPod touch. Furthermore,
the app must be running and
visible for proper operation of
all the N-hance features such as
personalized alarms, weather,
etc, etc. Launch the N-hance
App by touching the N-hance
icon on your iPhone or iPod
touch either just before or just
after docking.
Power failure indicator
If back-up batteries are not installed
or are too weak and AC power is
disconnected for a short period of time,
the time and alarm settings will be lost.
After AC power is restored
(reconnected), the Digital Display
will blink to indicate that power was
interrupted and you should re-adjust
the time and alarm settings.
iPhone, iPod, iPod classic, iPod nano
and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other
countries.
Normal operation will resume after
AC power is restored so you will not
have to reset the time or the alarm.
•
•
Note that the dock display will
be turned off when the app is
showing a clockface.
Refer to the User Guide found
within the N-hance App for
more detailed information.
General controls
Front view
Back view
Display
iPod/RADIO/AUX
AUX – Auxiliary input jack
DC jack – Connect power adapter
Off (standby mode)
STORE – Save radio stations as presets
RECALL – Recall preset radio stations
Top view
BRIGHTNESS – Adjust display brightness
REPEAT – Select repeat playback mode for iPod/
iPhone
SHUFFLE – Select random playback mode for iPod/
iPhone
SLEEP – Refer to “Sleep function”
NAP – Refer to “NAP function”
WAKE 1 – Activate or change Wake 1 settings
SNOOZE – Turn off the wake function
momentarily; turn off the sleep
function
<< or >> – Search radio frequencies; skip or search
music file in iPod; adjust clock time, wake time and
snooze period
VOL – / VOL + – Adjust volume
SET – Enter setting mode for setting clock time,
Wake 1 time or Wake 2 time
WAKE 2 – Activate or change Wake 2 settings
DST – Daylight saving time (refer to “Clock”)
TIME ZONE – Time zone selection (refer to “Clock”)
Universal dock for iPod/iPhone
Clock
US time zones
•
A confirmation message
Setting the clock
1. Press SET on the top of the unit
until the clock setting icon
flashes on the display.
(on) or
(off) shows on the
display when you make a selection.
Seattle
Olympia
Washington
Maine
Augusta
Montana
North Dakota
Bismarck
Salem
Helena
Selecting your time zone
Minnesota
St. Paul
Montpelier
Vt.
Albany
New York
N.H.
Oregon
Idaho
Boise
Concord
Boston
2. Press << or >> on the top of the
unit to set the clock time. The time
decrements or increments follow by
a faster rate when you press and
hold the button.
South Dakota
Pierre
Mass.
Wisconsin
Madison
•
Press TIME ZONE repeatedly on the
top of the unit to cycle through the
time zones (EST > CST > MST > PST
> AKST > HST > AST > EST...). The
default time zone is Eastern (EST)
(refer to the maps on the right).
The selected time zone shows on
the display briefly with TIME ZONE
icon flashes on the display.
Providence
Michigan
Lansing
Detroit
R.I.
Wyoming
Hartford
Conn.
New York
Trenton
Pennsylvania
Philadelphia
Harrisburg
Md.
Chicago
Iowa
New Jersey
Delaware
Cheyenne
Nebraska
Sacramento Carson City
Alaska
(AKST)
Des Moines
Salt Lake City
Utah
Ohio
Columbus
Lincoln
Nevada
Indiana
Illinois
Springfield
WAansnhapinolgiston, D.C.
West
San Francisco
California
Virginia
Indianapolis
Denver
Richmond
Virginia
Topeka
Colorado
St. Louis
Charleston
Frankfort
Kentucky
Kansas
Jefferson City
Las Vegas
Summer
Missouri
Raleigh
North Carolina
Winter
Nashville
Los Angeles
Santa Fe
Tennessee
Memphis
Oklahoma
Oklahoma City
•
The clock setting icon
flashes
Arizona
Phoenix
Columbia
Arkansas
Little Rock
South
New Mexico
Atlanta
Carolina
Alabama
Montgomery
when you are setting the time. AM
or PM icon also lights beside the
time.
Mississippi
Jackson
Georgia
•
Dallas
Hawaii-
Aleutian
(HST)
Louisiana
Texas
Baton
Austin
Rouge
New Orleans
Houston
Florida
Miami
Puerto Rico
Pacific Mountain
(PST) (MST)
Central Eastern
(CST) (EST)
Atlantic
(AST)
Canadian time zones
3. To save and exit the clock setting,
wait for about 5 seconds or press
SET until the clock setting icon (
) is off and the wake setting icons (
•
•
When the N-hance App is
running, the clock will be
synced to the clock time
Yukon
Territory
/
/
or
/
/
) are either
Nunavut
off or stop flashing.
Northwest Territories
on the iPhone or iPod.
The time on your iPhone is
provided by your mobile phone
service. The time on your iPod
is provided from iTunes during
the last connection to your
computer. Please note that it
is possible to have up to 59
seconds time difference between
your RCA clock display and your
iPhone or iPod time display.
British
Columbia
WARNING: Do not change these button
settings during the Clock or Alarm Set
mode.
Newfoundland
Summer
Alberta
Winter
Manitoba
Saskatchewan
Quebec
Saskatoon
Regina
Ontario
Selecting daylight saving
Winnipeg
•
Press and hold DST on the top of
the unit to turn on/off in areas
observing/not observing such time
change.
Pacific Mountain Central Eastern
(PST) (MST) (CST) (EST)
Atlantic
(AST)
Radio
iPod/iPhone
Listening to the radio
To turn on or off radio:
1. Press RADIO on the front of the
unit to turn on the radio.
Station presets
Listening to iPod/iPhone
To connect iPod/iPhone:
Place the appropriate adapter provided
with your iPod/iPhone and then place
your iPod/iPhone on the universal dock
for iPod/iPhone.
Made for:
To store a station as preset:
1. Tune to a radio station.
•
•
iPhone 4 16GB, 32GB
iPhone 3GS 8GB, 16GB,
32GB
•
The radio mode icon (
the display.
) lights on
2. Press STORE.
•
•
iPhone 3G 8GB, 16GB
iPod touch 4th generation 8GB,
32GB, 64GB
•
An available preset location
(e.g. ) shows on the display.
2. Press OFF to turn off the radio, or
press AUX or iPod to select another
sound mode.
To select iPod mode:
•
•
•
•
•
•
•
iPod touch 3rd generation 32GB,
64GB
iPod touch 2nd generation 8GB,
16GB, 32GB
iPod touch 1st generation 8GB,
16GB, 32GB
iPod nano 6th generation 8GB,
16GB
iPod nano 5th generation 8GB
or 16GB
iPod nano 4th generation
(video) 8GB, 16GB
iPod nano 3rd generation
(video) 4GB, 8GB
3. Press << or >> (or RECALL) to select
a desired preset location (1 - 20).
•
•
•
•
Press iPod on the front of the unit
to select the iPod mode.
The iPod mode icon ( ) lights on
the display.
Playback from the iPod/iPhone starts
automatically.
If no iPod/iPhone is connected
in the iPod mode, the unit will
exit the iPod mode and turn off
automatically.
To tune frequency:
•
Press << or >>. The selected
4. Press STORE.
frequency shows on the display.
Press and hold to automatically
search for the next available station.
•
shows on the display as
confirmation.
•
•
You can save up to 20 preset
stations.
FM Antenna
To recall a preset station:
1. In radio mode, press RECALL.
This unit is equipped with an FM
antenna at the back. Uncoil the antenna
to its full length for best reception. Tape
the end of the antenna onto the wall if
possible to improve reception.
•
The existing preset station number
shows on the display.
•
•
iPod classic 80GB, 120GB, 160GB
iPod nano 2nd generation
(aluminum) 2GB, 4GB, 8GB
iPod nano 1GB, 2GB or 4GB
iPod 5th generation (video)
30GB, 60GB, 80GB
2. Press << or >> (or RECALL) to select
a desired preset station.
•
•
•
•
•
iPod mini 4GB, 6GB
iPod 4th generation 20GB, 40GB
iPod 4th generation (color
display) 20GB, 30GB, 40GB, 60GB
iPod/iPhone
Wake function
2. Press WAKE 1 or WAKE 2 to select
a wake mode. A corresponding icon
lights on the front of the unit.
– Wake time 1 by alarm
Setting wake time
To control the playback:
1. During playback, press iPod to
pause the playback and press again
to resume.
To charge the iPod/iPhone:
•
You may charge the battery of your
iPod/iPhone through the universal
dock for iPod/iPhone while the
unit is turned off (standby mode)
or in the AUX, Radio or iPod
mode. Charging control should be
operated on the iPod/iPhone. It
is not necessary to charge in iPod
mode, unless you are listening to
the iPod/iPhone.
This unit allows 2 wake times to be set.
1. Press SET on the top of the unit
until a WAKE 1 icon (
) or a WAKE 2 icon (
flashes on the display.
,
or
or
– Wake time 1 by radio
– Wake time 1 by iPod/IPhone
– Wake time 2 by alarm
– Wake time 2 by radio
– Wake time 2 by iPod/IPhone
,
)
2. Press << or >> to skip to the
previous or next file.
•
Press and hold << or >> to search
2. Press << or >> on the top of the
backward or forward.
unit to set the wake time. The time
decrements or increments follow by
a faster rate when you press and
hold the button.
If Waking to Alarm (
,
) is
3. Press SHUFFLE to play the files in
random order in the iPod/iPhone.
Press again to cancel the function
(shows on the iPod/iPhone display).
selected:
•
The unit is equipped with GRAD-
U-WAKE. The alarm volume will
increase gradually to its maximum
in about 30 to 45 seconds.
4. Press REPEAT to select a repeat
playback mode (repeat 1 or repeat
all). Press REPEAT until no repeat
mode is selected (shows on the
iPod/iPhone display) to cancel the
repeat playback.
•
Note that the Alarm mode is not
affected by the volume control. If
you set the wake function with a
low volume setting for the Radio
before going to bed, it is advisable
to use Wake to Alarm mode to
wake you up since the Alarm will be
at a louder volume setting than the
Radio mode.
3. To save and exit the wake setting,
wait for about 5 seconds or press
SET until the clock setting icon (
) is off and the wake setting icons (
/
/
or
/
/
) are either
off or stop flashing.
Auxiliary source
•
To check the wake time after
setting, press SET until a WAKE
1 icon (
icon (
/
/
) or WAKE 2
) flashes and
If Waking to RADIO (
selected:
) is
To select auxiliary mode:
•
Adjust the auxiliary player to mid-
range volume and adjust the master
volume on the unit. Do not turn
the volume of the auxiliary player
too high as this may affect the
sound quality. For other playback
operations, control them on your
auxiliary player.
/
/
1. Connect your auxiliary source (e.g.
mp3 player) to the AUX input jack
at the back of the unit with an
audio cable (not supplied).
the respective assigned wake time
shows on the display.
3. Select a desired wake up radio
channel (refer to “Listening to the
radio”). If no wake up channel is
set, your last listening radio station
will be selected.
Select the wake source
You may choose to wake to radio, alarm
sound or music from iPod/iPhone.
1. Set a wake time (see Setting Wake
Time directions).
2. Press AUX to turn on the unit or to
switch to listen to AUX from other
modes.
4. Adjust the volume to your desired
level.
•
The auxiliary mode icon (
lights on the display.
)
5. Press OFF to turn off the unit.
Sleep function
In the sleep mode, the radio, iPod or
AUX mode turns off automatically.
To listen to the auxiliary player:
If Waking to iPod/iPhone (
selected:
3. Adjust the volume to your desired
level. The last played file on the
iPod/iPhone will be played when the
wake function activates.
,
) is
To stop the wake function:
•
If an auxiliary player (e.g. mp3
player) is connected, press AUX to
select AUX mode and start playback
on your auxiliary player.
•
Press OFF. The alarm will be on
again the following day at the same
time.
OR
To set the sleep time:
1. Press SLEEP repeatedly to cycle
among the sleep time available
(90min, 60min, 30min, 15min and
OFF. 90min is the default setting).
To change or check the remaining
time in sleep mode:
To disable the wake function
completely:
4. Press OFF to turn off the unit.
•
The icon
flashes while selecting.
•
Press SLEEP once to check the
remaining sleep time. Press SLEEP
repeatedly to select another sleep
time.
•
Press WAKE 1 or WAKE 2
Note: If there is no iPod/iPhone
connected, the alarm tone will sound
instead even if Waking to iPod mode
is selected.
repeatedly until no corresponding
2. When the desired sleep time is
selected, release SLEEP and wait for
about 5 seconds, the sleep time is
now set.
wake indicator (
,
,
or
,
,
) shows on the display.
To cancel the sleep mode:
SmartSnoozeTM
•
The icon
lights on the display.
•
If you decide to turn off the unit
sooner, press SNOOZE, OFF or press
SLEEP repeatedly to select “OFF”.
•
When the wake
This operation allows extra sleep time
function activates, the
corresponding wake
icon will flash until the wake
function is turned off. The icon
will then stop flashing and keep
lighting up.
To listen to the radio:
when the alarm sounds. The alarm will
be silenced by pressing SNOOZE, VOL +,
VOL –, SLEEP or NAP until the snooze
period is over. Snooze function can be
used repeatedly up to 1 hour. After this,
the wake function will turn off until the
next day.
•
The radio turns on by default. If
not, press RADIO and select a radio
station as usual.
To listen to the iPod/iPhone:
•
When the AC power is
disconnected, all wake mode will
be reverted to alarm tone.
•
•
•
Press iPod and then press << or >>
to select a file on the iPod/iPhone.
Playback will be in repeat all files
mode automatically.
If iPod mode is selected in your last
sleep mode setting, the iPod/iPhone
will start to play, instead of the
radio.
To set the “quiet” period with
Snooze:
While pressing SNOOZE, press << or
>> on the top of the unit to set the
“quiet” period from 1 to 30 minutes
(default: 9 minutes). Then release
SNOOZE to save the setting.
Turn off the wake
function
To silence the wake function
momentarily:
The radio will be played whenever
the iPod mode is selected but
without an iPod/iPhone connected.
•
Press SNOOZE. The alarm will sound
again when the snooze period is
over. (refer to “SmartSnoozeTM”).
OR
NAP function
Warranty information
For catnaps up to 2 hours without
disturbing the regular alarm settings,
the NAP function wakes you up after a
short period of time.
•
Only alarm tone is available in the
NAP mode.
12 Month Limited Warranty
Applies to RCA Clock Radios
computer peripherals, other media
players, home networks or vehicle
electrical systems.
To check the remaining NAP time:
•
AUDIOVOX ACCESSORIES CORP. (the
Company) warrants to the original retail
purchaser of this product that should
this product or any part thereof, under
normal use and conditions, be proven
defective in material or workmanship
within 12 months from the date of
original purchase, such defect(s) will be
repaired or replaced with reconditioned
product (at the Company’s option)
without charge for parts and repair
labor.
Press NAP once to show briefly the
NAP time left.
This Warranty does not apply to any
product or part thereof which, in the
opinion of the Company, has suffered
or been damaged through alteration,
improper installation, mishandling,
misuse, neglect, accident, or by removal
or defacement of the factory serial
number/bar code label(s). THE EXTENT
OF THE COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
To set the NAP time:
1. Press NAP repeatedly to cycle
among the NAP time available
(10min, 20min, 30min, 60min,
90min, 120min and OFF. 20min is
the default setting).
To cancel the NAP function:
•
Press and hold NAP or press NAP
repeatedly to select OFF.
•
The icon NAP flashes while
To turn off the NAP alarm:
•
selecting.
Press NAP or OFF to stop the NAP
alarm.
2. When the desired NAP time is
selected, release NAP and wait for
about 5 seconds, the NAP time is
now set. The current time shows
and the icon NAP lights on the
display.
To obtain repair or replacement
within the terms of this Warranty, the
product is to be delivered with proof
of warranty coverage (e.g. dated bill
of sale), specification of defect(s),
transportation prepaid, to the Company
at the address shown below.
This Warranty is in lieu of all other
express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF
Display brightness
This Warranty does not extend to the
elimination of externally generated
static or noise, to correction of
MERCHANTABILITY, SHALL BE LIMITED
TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH
OF ANY WARRANTY HEREUNDER
INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY
Press BRIGHTNESS to adjust the level
and press again to restore to the
original brightness level.
Display readout:
If you have the unit on, and
an input is selected, but the
volume is turned to 0, the display will
show dn00 as a reminder. To prevent
this, simply press the volume up.
e.g. UP10.
antenna problems, loss/interruptions of
broadcast or internet service, to costs
incurred for installation, removal or
reinstallation of product, to corruptions
caused by computer viruses, spyware or
other malware, to loss of media, files,
data or content, or to damage to tapes,
discs, removable memory devices or
cards, speakers, accessories, computers,
CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY. No person or
Illustraations coontainedd within this
publicatiion arre for rrepreesentaation only
and subjecct to change.
representative is authorized to assume
for the Company any liability other than
expressed herein in connection with the
sale of this product.
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd.
The descripptions andd characteeristics
given in tthis docuument aree given as
a generaal indicaation anndd not as a
guarantee. In ordeer to proovvide the
highest qquality pprroduct poossible,
we reserve the righht to maake any
improvemment or moodificattion without
prior nootice.
Hauppauge N.Y. 11788
Some states do not allow limitations on
how long an implied warranty lasts or
the exclusion or limitation of incidental
or consequential damage so the above
limitations or exclusions may not apply
to you. This Warranty gives you specific
legal rights and you may also have
other rights which vary from state to
state.
1-800-645-4994
For Canada Customers, please ship to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
Recommendations before returning
your product for a warranty claim:
•
Properly pack your unit. Include
any remotes, memory cards, cables,
etc. which were originally provided
with the product. However DO NOT
return any removable batteries,
even if batteries were included
with the original purchase. We
recommend using the original
carton and packing materials. Ship
to the address shown below.
Note that product will be returned
with factory default settings.
Consumer will be responsible to
restore any personal preference
settings.
the best accessories for your products.
•
© 2011 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) ® Registered
Printed in China
IMPORTANT SAFETY INSTRUCTIONS
FCC Information
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
came with your product or that is
listed in the user’s guide.
•
•
Only use attachments/accessories
specified by the manufacturer.
Use only with
WARNING: The battery (battery or
batteries or battery pack) shall not
be exposed to excessive heat such as
sunshine, fire or the like.
•
Attention should be drawn to the
environmental aspects of battery
disposal.
The use of apparatus in moderate
climates.
Note: This equipment has been tested
and found to comply with the limits
for a Class B digital device, pursuant
to Part 15 of FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
•
•
Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
Always leave sufficient space around
the product for ventilation. Do
not place product in or on a bed,
rug, in a bookcase or cabinet that
may prevent air flow through vent
openings.
Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
Care should be taken so that objects
do not fall into the product.
Do not attempt to disassemble
the cabinet. This product does
not contain customer serviceable
components.
the cart, stand,
•
]
tripod, bracket,
or table
Ecology
specified by the
manufacturer,
or sold with
Important battery
precautions
Help protect the environment - we
recommend that you dispose of used
batteries by putting them into specially
designed receptacles.
Portable Cart Warning
the apparatus.
•
•
•
Any battery may present a risk of
fire, explosion, or chemical burn
if abused. Do not try to charge a
battery that is not intended to be
recharged, do not incinerate, and
do not puncture.
Non-rechargeable batteries, such as
alkaline batteries, may leak if left in
your product for a long period of
time. Remove the batteries from the
product if you are not going to use
it for a month or more.
If your product uses more than one
battery, do not mix types and make
sure they are inserted correctly.
Mixing types or inserting incorrectly
may cause them to leak.
Discard any leaky or deformed
battery immediately. They may
cause skin burns or other personal
injury.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
Unplug this apparatus during
lightning storms or when unused
for long periods of time.
Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
•
Some of the following information may
not apply to your particular product;
however, as with any electronic product,
precautions should be observed during
handling and use.
However, there is no guarantee
that interference will not occur in a
particular installation. If this equipment
does cause harmful interference to
radio or television reception, which
can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
•
•
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near
water.
•
•
The marking information is located
at the bottom of apparatus.
To be completely disconnect the
power input, the AC/DC adapter
of apparatus shall be disconnected
from the mains.
•
•
•
Reorient or relocate the receiving
antenna.
•
•
Clean only with dry cloth.
Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
Increase the separation between the
equipment and receiver.
Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
•
•
•
•
•
AC/DC adapter is a disconnect
device. The AC/DC adapter should
not be obstructed OR should be
easily accessed during intended use.
The ventilation should not be
impeded by covering the ventilation
openings with items such as
newspaper, table-cloths, curtains etc.
No naked flame sources, such as
lighted candled, should be placed
•
•
ADDITIONAL SAFETY INFORMATION
•
The AC/DC adapter supplied with
this product is intended to be
correctly oriented in a vertical or
floor mount position.
Do not use unauthorized chargers
or power adapters. Use only
chargers or power adapters that
Please help to protect the
environment by recycling or
disposing of batteries according to
federal, state, and local regulations.
•
Consult the dealer or an
experienced radio/TV technician for
help.
•
Changes or modifications not expressly
approved by Audiovox could void
the user’s authority to operate the
equipment.
on the apparatus.
|