Safety precautions
Attaching wall mount plate
Drywall Installation
Follow these precautions to ensure safe installation and
mounting of your flat panel TV.
1. Use a stud finder to locate a wood stud where you want
to install the mount.
NOTE: It is required that the wall mount plate be
LCD TV Wall Mount
1. Be sure you have purchased the correct wall mount
attached to wall studs.
for your TV. Recheck the size and weight constraints.
2. Locate center of stud.
with Double Swing Arm Extension
Installation Manual
2. Gather all necessary tools before you begin installation.
You will need a #3 bit Phillips screwdriver, electric
drill, drill bit (included), level (integrated level on
product), stud finder, and hammer (for brick and
concrete installations).
3. Place the wall mount plate against the wall, with the
cord management channel towards the bottom. Level it
using the bubble guide. Mark the locations on the wall
where the mount is to be installed.
Fits TVs 13"- 27"
4. Drill holes at each marked location using the enclosed
3. It is essential for the wall mount plate to be attached
wood drill bit.
Maximum Load Capacity – 40 lbs. (18 kg)
to wall studs. (Use a stud finder.)
5. Secure the wall mount plate to the wall, using one
4. Use the included hardware for mounting purposes.
This hardware has been provided to ensure a safe and
secure mount.
drywall screw, but do not completely tighten it yet.
6. Using the integrated bubble level, carefully adjust the
wall mount plate until it is level.
5. Hire a licensed electrician to relocate an electrical
7. Insert the remaining screws and tighten all three
outlet, if needed.
screws completely.
6. Be sure to purchase wires long enough to connect
the TV to the audio and video components in your
installation.
MAF40BK
Concrete/Brick Installation
Thank you for choosing a Universal Flat Panel TV Wall
Mount from RCA. This mount can be used for all major
brands of 13" - 27" flat panel TVs, 40 lbs (18 kg) or under.
This wall mount features a 0-15-degree tilt, 180-degree
pan and swivel, and double swing arm extension for easy
viewing. Before attempting to mount your television set,
please remove all parts from this package and read the
installation instructions carefully.
7. We recommend you hire a professional installer,
if you have any concerns about installing the TV
wall mount yourself.
1. Place the wall mount plate against the wall with the
cord management channel towards the bottom.
2. Using the integrated bubble level, mark off the position
of the holes that will be used for securing the mount.
3. Place the wall mount plate aside.
Keep your sales receipt to obtain warranty parts and
service and for proof of purchase. Attach it here and record
the model number. This number is located on the product.
4. Using an electric drill and a 5/16" (8mm) masonry bit,
drill holes in the marked locations.
5. Remove any excess dust from the holes.
6. Insert a concrete anchor into each hole. If necessary,
use a hammer to lightly tap each anchor into place so
they are flush with the wall.
WARNING: Use of this mount with a TV weighing
over 40 lbs. or with a screen larger than 27" could cause
the mount to fail causing property damage and/or
personal injury.
Model No. __________________________________________
Purchase Date: ______________________________________
Dealer/Address/Phone ______________________________
7. Once both anchors are in place, place the wall mount
plate back into position. Using the integrated bubble
level, carefully adjust the wall mount plate until it is
level.
Limited Lifetime Warranty
Audiovox Electronics Corporation (the “Company”) warrants to you the
original retail purchaser of this product that should it, under normal use
and conditions, be proven defective in material or workmanship during
its lifetime while you own it, such defect(s) will be repaired or replaced (at
the Company’s option) without charge for parts and repair labor.
8. Attach the wall mount plate, using the drywall screws
provided.
9. Make sure all screws are tightened and secure.
Product diagram
To obtain repair or replacement within the terms of this Warranty, the
product is to be delivered with proof of warranty coverage (e.g. dated bill
of sale), specification of defect(s), transportation prepaid, to the Company
at the address shown below. Do not return this product to the Retailer.
Attaching the TV mount plate
TV Mount Plate
This Warranty does not cover product purchased, serviced or used
outside the United States or Canada.
1. Unplug your flat panel TV before starting this step of
Adjustment Knob
the installation.
This Warranty is not transferable and does not extend to costs incurred for
installation, removal or reinstallation of the product. This Warranty does
not apply if in the Company’s opinion, the product has been damaged
through alteration, improper installation, mishandling, misuse, neglect,
or accident.
Double Swing Arm Extension
IMPORTANT: NEVER lay the TV face down as this
may cause damage to the viewing surface.
Retainer Clip
2. Before attaching the TV mount plate to the TV,
determine which hardware to use. Examine the back of
your TV. If the back is flat, use the M4x12mm bolts. If
your TV has a recessed back, use the longer M4x30mm
bolts and 1/2" spacers.
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
3. After you have determined which bolts to use, attach
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
SHALLBELIMITEDTODURATIONOFTHISWARRANTY.INNOCASE
SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTALDAMAGESWHATSOEVER.Nopersonorrepresentativeis
authorized to assume for the Company any liability other than expressed
herein in connection with the sale of this product.
the TV mount plate to the back of your TV.
NOTE: Be careful not to over-tighten the bolts.
Integrated Bubble Level
Wall Mount Plate
Security Bolt Position
Some states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you. This
Warranty gives you specific legal rights and you may also have other
rights which vary from state/province to state/province.
Cord Management Channel
Attaching the TV mount plate
to the wall mount plate
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,
Hauppauge, New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
Unit 3, Door 16, Mississauga, Ontario L5T 3A5
1. To complete the installation, slide the TV mount plate
with your TV attached into the wall mount plate.
Trademark(s) Registered, Marques Deposee, Marcas Registradas.
All other brands and product names are trademarks or registered
trademarks of their respective owners.
2. The retainer clip on the top of the wall mount plate
Specifications
should click, indicating that the mount is secure.
3. To remove the TV, push in on the clip and slide the TV
© 2008 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Model:
MAF40BK
Two-piece, low-profile design
mount plate up.
4. For additional security and stability, insert the security
Description:
RCA Universal LCD TV Wall
Mount with Swing Arm Extension
bolt into the hole located at the base of the unit.
MAF40BK_US_IB_00
5. Tighten, using the Allen Wrench provided.
Color:
Black
TV Size Range:
Max. Load:
Min. Profile:
13" – 27"
Preparing to install
40 lbs. (18kg)
2.6" (6.6 cm)
Before beginning the installation process, verify that you
have all the necessary tools on hand. The following tools
are required for proper installation:
Operation and adjustment
Max. Extension: 9.7" (24.6 cm)
Tilt:
+/- 0-15°
180°
Your RCA Flat Panel TV Wall Mount features an adjustable
15-degree tilt and 180-degree pan and swivel action for
easy viewing.
Swivel:
Tools
VESA Compliant: 75/100
Integrated Bubble Level
Cord Management System
#3 bit Phillips screwdriver
Stud finder
To adjust the tilt:
Electric drill
1. Locate the adjustment knob directly behind the TV
Drill bit (included)
mounting point.
5/16" (8mm) masonry drill bit for concrete/
brick installation
2. Loosen the knob by turning it counter-clockwise.
3. Adjust the tilt to the desired level and re-tighten the
Level (integrated level on product)
Allen Wrench (included)
knob to lock the adjustment in place.
Hammer (for concrete installations)
To adjust the swivel:
1. Simply move the extension arm into the desired
position.
Package Contents
2. If the joint is too tight or too loose, adjust the tightness
Make sure all the hardware has been included with
your mount.
of the joint.
3. Locate the knob closest to the wall.
(1) Drill Bit
4. Turn the knob counter-clockwise to loosen and
(3) 1-7/8" Drywall Screws
(3) Concrete Anchors
(2) Allen Wrenches
(4) M4x12mm Bolts
(4) M4x30mm Bolts
(4) 1/2" Spacers
clockwise to tighten.
(1) Security Bolt
(1) Phillips-Head Driver
|