MST65BKR
Fits TVs 37”- 65”
flat panel solutions
Tilt Wall Mount for LCD, Plasma, and
LED Displays
Maximum Load
Capacity – 165 lb (75kg)
Instruction Manual
Specifications
Display Size:
Maximum Load:
Mounting Pattern:
Tilt Range:
37” to 65”
165 lb (75kg)
800 mm x 500 mm (31.5” x 19.7”) max
15° down
Profile:
1.4” (3.5 cm)
Box contents
Upper Wall Plate (x1)
Lower Wall Plate (x1)
Left Plastic Side (x1)
Right Plastic Side (x1)
Mount Arm (x2)
Instruction Manual (x1)
Hardware Kit (x1)
Template (x2)
Warnings
1. Read these instructions before you begin. If
you are unsure of any part of the process, contact
a professional contractor or installer for assistance.
Improper installation can result in injury or damage.
CAUTION:
This wall mount is intended for use only with the
maximum weight of 75 kg (165 lbs). Use with heavier
than the maximum weights indicated may result in
instability causing possible injury.
2. The wall or mounting surface must be capable of
supporting the combined weight of the mount and
the display; if not, the structure must be reinforced.
3. Locate pipes, wires, or any other hazards in the wall
where you wish to install the mount before drilling.
4. Safety gear and proper tools must be used. Failure
to do so can result in injury or damage.
5. A minimum of two people are required for
installation. Do not attempt to install this mount
alone under any circumstances.
6. Follow all instructions and recommendations
regarding adequate ventilation and suitable
locations for mounting your display. Consult the
owner‘s manual for your particular display for more
information.
Pour des instructions
en français, se
reporter à la page 6.
Para obtener
instrucciones en
español, consulte la
página 11.
Continues on next page...
5. Attach the wall plate to the wall using the M6.3 x 63 screws (A) and washers (B)
provided (see Fig. 3). Do not over-tighten these screws and do not release
the mount until all screws are in place. Ensure that the mount remains level
after all screws are secured.
Fig.3
Part 1B – Mounting to the Wall (Concrete)
IMPORTANT! For safety reasons, the concrete wall must be capable of
supporting the combined weight of the mount and the display. The manufacturer
takes no responsibility for failure caused by walls of insufficient strength.
1. Place the appropriate mounting template against the wall in the desired
location. Make sure the template is level.
Fig.4
2. Drill four 8 mm (5/16”) holes in the wall using the template as a guide. Remove
any excess dust from the holes (see Fig. 4).
3. Remove the template from the wall and insert a concrete anchor (C) into each
hole so that it is flush with the concrete surface (see Fig. 5). A hammer can be
used to lightly tap the anchors into place if necessary.
NOTE: If the concrete wall is covered by a layer of plaster or drywall, the
concrete anchor must pass completely through the layer to rest flush with the
concrete surface.
Fig.5
4. Place the assembled wall plate against the wall over the inserted anchors and
attach it using the M6.3 x 63 screws (A) and washers (B) provided (see Fig. 6).
Do not over-tighten these screws and do not release the mount until all
screws are in place. Ensure that the mount remains level after all screws are
secured.
Fig.6
Part 2 – Attaching the Mount Arms to the Display
IMPORTANT! Use extra care during this part of the installation. If possible, avoid placing your display facedown
as it may damage the viewing surface.
NOTE: This mount comes with a selection of different screw diameters and lengths to accommodate a wide variety
of display models. Not all of the hardware in the kit will be used. If you cannot find the appropriate screw size in the
kit provided, consult the manufacturer of your display for more information.
1. Determine the correct length of screw to use by examining the back of your display:
A. If the back of your display is flat and the mounting holes are flush with the surface, you will use the shorter
screws (D or F) from the hardware kit.
B. If the back of your display is curved, has a protrusion, or if the mounting holes are recessed, you will need
to use the longer screws (E or G) and may also need to use the spacers (I).
2. Determine the correct diameter of screw to use by carefully trying one of each size (M6 and M8) from the
hardware kit. Do not force any of the screws – if you feel resistance stop immediately and try a smaller
diameter screw.
Continues on next page...
3
3. Attach the mount arms to the back of your display using the screws identified in steps 1 and 2 (see Fig. 7):
For displays with flat
backs.
For displays with
curved or recessed
backs.
Fig.7
A. If you are using the M6 screws you will also need to use the M6 washers (H). M8 screws do not require
washers.
B. If you are using the longer screws on a display with a curved or recessed back, you may also need to use
the spacers (I). Use one spacer or two spacers stacked as needed. Only use the spacers if necessary.
NOTE: Make sure the mount arms are attached with the tilt mechanisms facing outward, exactly as shown in
the illustration (see Fig. 8). Otherwise, the tilt function cannot be accessed.
Tilt Adjustment
Tilt Adjustment
Mechanism
Mechanism
Fig.8
Part 3 – Final Assembly
1. Check to make sure the tilt mechanism is fully tightened. It can be tightened using the long Allen key (J)
provided in the hardware kit.
2. With the help of another person, carefully lift your display and place it on the mount. Do not release the
display until the mount arms have securely hooked onto the mount.
3. Make sure the safety locks have successfully engaged by gently pushing up on the display. You should not be
able to remove the display from the mount.
4. If the plastic tabs hang below the bottom of your display they can be trimmed
with a knife or looped back and tucked into the rubber ring located on each tab.
5. If you need to remove the display from the mount, pull the plastic tabs located
at the bottom of the mount arms down and then forward (away from the wall) to
1
engage the tooth and disengage the safety locks (see Fig. 9). With the help of
another person, carefully lift the display from the mount. Return the tabs to their
original position by pulling them down and pushing them backwards.
2
Fig.9
4
Operation and adjustment
1. To change the tilt angle of your display, hold the display firmly in place and
loosen the tilt mechanisms using the long Allen key (J) from the hardware kit
(see Fig. 10). Move your display to the desired position, and then re-tighten the
tilt mechanisms. If your display is in the non-tilt position, you will need to push
up gently on the display before you can move it. Do not release the display
until both tilt mechanisms are firmly tightened.
2. Periodically clean your mount with a dry cloth. Inspect all screws and hardware
at regular intervals to ensure that no connections have become loose over time.
Re-tighten as needed.
Fig.10
5
|