OPERATOR’S MANUAL
DUAL PORT BATTERY CHARGER
140276004
Fits all RIDGID
slide battery packs
Your dual port charger has been engineered and manufactured to our high standards for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Read The Operator’s Manual
Eye Protection
Always wear safety goggles or safety glasses with side shields and, as
necessary, a full face shield when operating this product.
Safety Alert
Precautions that involve your safety.
FEATURES
PRODUCT SPECIFICATIONS
Charger Voltage....................................................................................................9.6 Volt, 12 Volt, 14.4 Volt, and 18 Volt DC
Charger Input .......................................................................................................................................120 V, 60 Hz, AC only
Charge Rate ..........................................................................................................................................................30 minutes
4-1/8 in.
“KEY HOLE”
HANGER
Fig. 1
KNOW YOUR DUAL PORT CHARGER
“KEY HOLE” HANGER
The charger has a “key hole” hanging feature for convenient,
space saving storage. Screws should be installed so that
the center distance is 4-1/8 in.
See Figure 1.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
AUTOMATIC FAN SHUT-OFF
Your dual port charger is fan-cooled. When a battery pack
is fully charged (the green LED is on), the fan will automati-
cally shut itself off.
3
OPERATION
CHARGER SHOWN WITH 18 VOLT BATTERY PACK
APPLICATIONS
You may use this tool for the following purposes:
Charging 9.6 Volt, 12 Volt, 14.4 Volt, and 18 Volt RIDGID
slide batteries
CAUTION:
If at any point during the charging process none
of the LEDs are lit, remove the battery pack from
the charger to avoid damaging the product. DO
NOT insert another battery. Return the charger and
battery to your nearest service center for service
or replacement.
CHARGING THE BATTERY PACK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until the light on front of charger changes
from flashing green to continuous green.
NOTE: Batteries will not reach full charge the first time they
are charged. Allow several cycles (operation followed by
recharging) for them to become fully charged. This is normal
for nickel-cadmium batteries.
Fig. 2
NOTE: Refer to CHARGING THE BATTERY PACK for
normal recharging of batteries. If the charger does not charge
your battery pack under normal circumstances, return both
the battery pack and charger to your nearest repair center
for electrical check. For the location of your nearest repair
center, please call 1-866-539-1710.
TO CHARGE
Charge the battery pack only with the charger provided.
Make sure the power supply is normal household voltage,
120 volts, 60 Hz, AC only.
Connect the charger to a power supply.
Attach the battery pack to the charger by aligning the
raised ribs on the battery pack with the grooves in the
charger, then slide the battery pack onto the charger.
See Figure 2.
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
For average charge times, refer to the chart on the
following page.
When the batteries become fully charged, unplug the
charger from the power supply and remove the battery
pack.
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery warms to a temperature of more than 41°F
(5°C), the charger will automatically begin fast charge mode.
NOTE: Refer to CHARGING THE BATTERY PACK for
normal recharging of batteries. If the charger does not charge
your battery pack under normal circumstances, return both
the battery pack and charger to your nearest repair center
for electrical check. For the location of your nearest repair
center, please call 1-866-539-1710.
USE THIS RIDGID BATTERY CHARGER ONLY WITH
THE BATTERY PACKS LISTED BELOW.
CHARGING A HOT BATTERY PACK
When using the tool continuously, the battery pack will
become hot. Because the dual port charger is fan-cooled,
a hot battery pack may be placed directly onto the charger
port. When placed on the charger, a hot battery pack will
cool for 20 minutes or less before attempting to recharge.
Part Number Voltage
Part Number Voltage
130252007
130252002
130254001
130252003
130254002
9.6
12
130254008
130252001
130252004
130254003
130254007
14.4
18
12
18
If the battery pack is above normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery pack cools down to approximately 104°F
(40°C), the charger will automatically begin fast charge mode.
14.4
14.4
18
18
4
OPERATION
LED FUNCTION OF CHARGER
See Figure 3.
LED
INDICATOR
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
Power
Without battery pack ON
OFF
Ready to charge battery pack
When battery pack reaches cooled
temperature, charger begins fast
charge mode
Evaluate
Evaluate
Hot battery pack
Cold battery pack
Flashing
OFF
OFF
When battery pack reaches warmed
temperature, charger begins fast
charge mode
Flashing
Charger pre-charges battery until nor-
mal voltage is reached, then begins
fast charge mode
Evaluate
Defective
Deeply discharged
Defective
Flashing
Flashing
OFF
Flashing
Battery pack or charger is defective
• If defective, try to repeat the conditions a second time by removing and reinstalling the battery
pack. If the LED status repeats a second time, try charging a different battery.
• If a different battery charges normally, dispose of the defective pack (see Maintenance section).
• If a different battery also indicates “Defective,” the charger may be defective.
Charging
Fast charging
Slow charging
ON
Flashing
ON
See chart below for charge times
Fast charging is complete
Charger maintains charge mode
Full
OFF
BATTERY
AVERAGE CHARGE TIME
POWER
INDICATOR
RED LED
GREEN LED
COMPACT SERIES
18 min.
27 min.
34 min.
EVALUATE
INDICATOR
HC
HC 2.5
DEFECTIVE
INDICATOR
CHARGING
INDICATOR
NOTE: The 9.6 Volt, 12 Volt, and 14.4 Volt battery
packs will not slide all the way down onto the
charger port. Insert 9.6 Volt, 12 Volt, and 14.4 Volt
battery packs until they click into place and are
aligned with the line on the charger, shown at left.
Allow up to 5 seconds for the “charge” light to come
on after the battery pack is inserted.
FULL
INDICATOR
Fig. 3
5
MAINTENANCE
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
WARNING:
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a RIDGID authorized service center.
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
KEEPING THE CHARGER VENTS CLEAN
The fan in this charger will perform more efficiently if the air
vents and ports are kept clean and dust-free. Periodically
check the air vents for dust or other debris.
WARNING:
To avoid serious personal injury, always remove
the battery pack from the tool when cleaning or
performing any maintenance.
To clean the vents, unplug the charger. Using a fine nylon-
bristle brush, whisk dust or debris away from the air vents
and ports.
The battery pack has intake and exhaust vents that should
also be kept free of dust and debris. Clean the battery pack
vents by using a fine nylon-bristle brush to whisk away dust
or debris.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
When cleaning, do not allow metal to come into contact with
any of the vents or ports of the charger or battery pack.
BATTERY PACK REMOVAL AND
BATTERIES
The battery pack for this tool is equipped with nickel-cad-
mium rechargeable batteries. Length of service from each
charging will depend on the type of work you are doing.
PREPARATION FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries
properly.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-
cadmium batteries in ordinary trash.
Consult your local waste authority for information regarding
available recycling and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
Remove the battery pack from the charger once it is fully
WARNING:
charged and ready for use.
Upon removal, cover the battery pack’s terminals
with heavy-duty adhesive tape. Do not attempt
to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F.
Store battery packs in a “discharged” condition.
6
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers de-
fects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied war-
ranties, including warranties of MERCHANTABILITY or FIT-
NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or conse-
quential damages. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential dam-
ages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
Hwy. 8
Pickens, SC 29671
7
OPERATOR’S MANUAL
DUAL PORT BATTERY CHARGER
140276004
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
140276004
Model No.
Serial No.
983000-897
12-06-05 (REV:00)
|