43-1123.fm Page 1 Tuesday, September 5, 2000 11:13 AM
A
Cat. No. 43-1123
OWNER’S MANUAL
ET-1123
Please read before using this equipment.
900 MHz Digital Dual Keypad
Cordless Phone
with Speakerphone and
Caller ID/Call Waiting
43-1123.fm Page 3 Tuesday, September 5, 2000 11:13 AM
Two-Way Intercom/Paging System —
lets you send a signal from the base to
the handset, or from the handset to the
base, to locate the handset or page
someone using it away from the base. If
someone answers the page, you can
use the phone as an intercom and
speak to the person on the handset.
switch from pulse to tone dialing for
long-distance, bank-by-phone, or other
special services.
Redial — lets you quickly redial any of
the last three numbers dialed on the
handset. You can also redial the last
number you dialed on the base.
30 Channels — automatically selects a
clear channel when you make or answer
a call. You can also manually change
channels during a call.
Auto Talk — you can set the phone so
you can answer a call simply by lifting
the handset from the base.
Any Key Answer — you can set the
phone so you can press any key to an-
swer a call when the handset is away
from the base.
Headset Jack — lets you connect an
optional headset for handsfree conve-
nience.
Volume Controls — let you adjust the
volume you hear through the handset
and speakerphone.
Hearing-Aid Compatibility — lets you
use your phone with hearing aids that
have a T (telephone) switch.
Ringer Volume Control — lets you se-
lect from four ringer tone/volume set-
tings on the handset.
Facedown/Faceup Handset Charging
— you can charge the handset on the
base facedown or faceup.
Security Access-Protection Code —
helps prevent other cordless phone us-
ers from using your phone line while the
handset is off the base.
Wall Mountable — you can mount the
phone base on a wall to save space on
your desktop.
COM-LOK — ensures that other cord-
less phone users cannot use your phone
line when the handset is on the base.
Long Battery Life — the supplied bat-
tery pack (when fully charged) provides
about 7 hours of talk time or 7 days of
standby time.
Tone/Pulse Dialing — lets you use ei-
ther type of service, and you can easily
3
43-1123.fm Page 4 Tuesday, September 5, 2000 11:13 AM
Important Caller ID Information
FCC STATEMENT
To use the phone's Caller ID and Caller
ID with Call Waiting features, you must
be in an area where those services are
available and you must subscribe to
those services through your local phone
company.
Your phone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number
and the REN to your phone company.
These numbers are on the bottom of the
base.
Where Caller ID is offered, one or more
options are generally available:
You must not connect your phone to any
of the following:
• caller's number only
• caller's name only
• coin-operated systems
• party-line systems
• caller's name and number
• most electronic key phone systems
Note: Your telephone operates on stan-
dard radio frequencies, as allocated by
the FCC. Even though the security ac-
cess-protection code prevents unautho-
rized use of your phone line, it is
possible for radios operating on similar
frequencies within a certain area to unin-
tentionally intercept your conversations
and/or cause interference. This lack of
privacy can occur with any cordless
phone.
READ THIS BEFORE
INSTALLATION
We have designed your phone to con-
form to federal regulations, and you can
connect it to most telephone lines. How-
ever, each device that you connect to
the phone line draws power from the
phone line. We refer to this power draw
as the device's ringer equivalence num-
ber, or REN. The REN is on the bottom
of the base. If you are using more than
one phone or other device on the line,
add up all the RENs. If the total is more
than five (three in rural areas), your
phones might not ring. If ringer operation
is impaired, remove a device from the
line.
4
43-1123.fm Page 5 Tuesday, September 5, 2000 11:13 AM
CONTENTS
Preparation .............................................................................................................. 6
Mounting the Phone ........................................................................................... 6
Connecting and Charging the Battery Pack ....................................................... 8
Setting the Dialing Mode .................................................................................... 9
Turning the Base Ringer On/Off ....................................................................... 10
Setting the Handset’s Ringer Tone/Volume ...................................................... 10
Setting Auto Talk .............................................................................................. 10
Turning Caller ID/Call Waiting On/Off ............................................................... 10
Storing Your Area Code ................................................................................... 11
Operation ............................................................................................................... 12
Making a Call .................................................................................................... 12
Receiving a Call ............................................................................................... 12
Adjusting the Handset Volume ......................................................................... 13
Selecting the Channel ...................................................................................... 13
Using Mute ....................................................................................................... 13
Switching Between the Handset and the Speakerphone ................................. 13
Using Both the Handset and the Speakerphone .............................................. 14
Using Flash ...................................................................................................... 14
Using Redial ..................................................................................................... 14
Using Tone Services On a Pulse Line .............................................................. 14
Using Page/Intercom ........................................................................................ 15
Transferring a Call Between the Handset and the Base .................................. 15
Out of Range .................................................................................................... 16
Using a Headset ............................................................................................... 16
Memory Dialing ................................................................................................ 17
Caller ID Operation ........................................................................................... 20
Troubleshooting .................................................................................................... 23
Care and Maintenance .......................................................................................... 25
Replacing the Battery Pack .............................................................................. 26
The FCC Wants You to Know ........................................................................... 27
Lightning ........................................................................................................... 27
5
43-1123.fm Page 6 Tuesday, September 5, 2000 11:13 AM
PREPARATION
Note: The base unit display is protected
during shipment by a piece of clear film.
Carefully peel off this film before using
your phone for the first time.
store. Or, you can let the phone
company update the wiring for you.
• The USOC number of the jack to be
installed is RJ11C (RJ11W for a wall
plate).
MOUNTING THE PHONE
On a Desk Top
You can place the phone's base on a
desk or table, mount it on a standard
wall plate, or mount it directly on a wall.
Choose a location that is:
1. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
• near an AC outlet
• near a modular telephone line jack
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
2. Plug the modular cord's other end
into a modular telephone line jack.
3. Insert the supplied AC adapter's
barrel plug into the DC IN 9V jack on
the back of the base.
• away from other cordless phones
The base's location affects the phone's
range. If you have a choice of several lo-
cations, try each to see which provides
the best performance.
Caution: The supplied RadioShack
adapter was designed specifically for
your phone. Use only the supplied
adapter.
4. Route the adapter's cord through
the strain relief slot on the bottom of
the base.
Notes:
Strain Relief Slot
• Your telephone connects directly to
a modular telephone line jack. If
your phone line jack is not a modu-
lar jack, you can update the wiring
yourself, using jacks and adapters
available at your local RadioShack
6
43-1123.fm Page 7 Tuesday, September 5, 2000 11:13 AM
5. Plug the adapter into a standard AC
outlet.
in Step 3 of “On a Desk Top” on
Page 7.
6. Lift the base's antenna to a vertical
position.
5. Route the adapter and modular
cords through the grooves on the
bracket.
Adapter
On a Wall Plate
and
Modular
Cord
1. Detach the stand from the base by
pressing the latches on the stand.
Grooves
Stand
6. Plug the modular cord's other end
into the wall plate jack, then align
the bracket's keyhole slots with the
wall plate studs and slide the base
downward to secure it.
2. Insert the two tabs at the top of the
narrow end of the supplied bracket
into the base's upper tab slots as
shown, then press down on the
bracket's latches and insert them
into the lower slots.
Bracket
7. Plug the adapter into a standard AC
outlet.
8. Press and lift out the handset
holder, flip it over as shown, then
snap it back into place so it holds
the handset.
3. Plug one end of the supplied short
modular cord into the TEL LINE jack
on the back of the base as in Step 1
of “On a Desk Top” on Page 6.
4. Insert the supplied AC adapter's
9. Lift the base's antenna to a vertical
position.
barrel plug into the DC IN 9V jack as
7
43-1123.fm Page 8 Tuesday, September 5, 2000 11:13 AM
On a Wall
CONNECTING AND
CHARGING THE BATTERY
PACK
To mount the phone directly on a wall,
you need two screws (not supplied) with
heads that fit into the keyhole slots on
the bottom of the base. Follow the steps
under “On a Wall Plate” on Page 7, then
apply these additional instructions for
placement on a wall.
The phone comes with a rechargeable
nickel-cadmium battery pack installed in
the handset, but not connected. Before
using your phone, you must connect the
battery pack, then charge it for about 24
hours.
15
16
1. Drill two holes 3 /
inches (100 mm) apart.
Then thread a screw
into each hole, letting
1. Press down and slide off the battery
pack compartment cover.
the heads extend about
5
16
/ inch (8 mm) from the
wall.
2. Plug one end of the supplied long
modular cord into the TEL LINE jack
at the back of the base.
2. Lift the battery pack out of the com-
partment. Plug the battery pack's
connector into the socket in the
compartment. The connector fits
only one way.
3. Align the bracket's keyhole slots
with the mounting screws and slide
the base downward to secure it.
3. Put the battery pack in the compart-
ment.
4. Replace the cover.
To charge the battery pack, simply place
the handset on the base, facing either
up or down. The CHARGE/IN USE indi-
cator on the base lights.
Recharge the battery pack when Low
Batteryflashes on the handset's dis-
play.
8
43-1123.fm Page 9 Tuesday, September 5, 2000 11:13 AM
Important: Be sure the battery pack is
properly connected before you try to
charge it.
battery pack loses its ability to fully
recharge.
• If the battery pack is completely dis-
charged or the base loses power
while the handset is away from it,
place the handset on the base to
reset the security access-protection
code. If it was the handset that lost
power, recharge the battery pack.
Notes:
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear a five-beep error sig-
nal. If this happens, return the hand-
set to the base for about 5 seconds.
This resets the security access-pro-
tection code.
• The supplied battery pack should
last about a year. When it loses its
ability to fully recharge, order a
replacement battery pack through
your local RadioShack store (see
“Replacing the Battery Pack” on
Page 26).
• Using a pencil eraser, clean the
charging contacts on the handset
and the base about once a month.
SETTING THE DIALING
MODE
Set DIAL MODE P- -T on the back of the
base for the type of service you have. If
you are not sure which type you have,
after you charge the handset battery
pack, do this simple test.
• If the handset's display is blank and
the phone does not work, recharge
the battery pack. (The battery power
might be too low to light the display.)
1. Set DIAL MODE P- -T to -T.
2. Press SPEAKER and listen for a dial
• If the battery pack becomes weak
during a call, the handset beeps
every 3 seconds and Low Bat-
tery flashes. When this happens,
you cannot make another call on the
phone until you recharge the battery
pack.
tone.
3. Press any number other than 0 on
the base's keypad.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code number either.
• About once a month, fully discharge
the battery pack by keeping the
handset off the base until Low
Battery flashes. Otherwise, the
9
43-1123.fm Page 10 Tuesday, September 5, 2000 11:13 AM
If the dial tone stops, you have
touch-tone service. Leave DIAL
MODE P- -T set to -T. If the dial tone
continues, you have pulse service.
Set DIAL MODE P- -T to P-.
change the setting. Press the other but-
ton to change the setting.
SETTING AUTO TALK
4. Press SPEAKER to hang up.
Your phone is preset so you must press
TALK to answer a call. With auto talk
turned on, you can answer a call by just
lifting the handset from the base, or, if
the handset is away from the base, by
pressing any key.
TURNING THE BASE
RINGER ON/OFF
To turn off the base's ringer, set RINGER
on the back of the base to OFF. You can
still make or receive calls using this
phone. Telephones on the same line
(and the phone's handset if it is away
from the base) still ring when there is an
incoming call.
Follow these steps to turn auto talk on or
off.
1. Lift the handset and hold down
CALL ID until the Caller ID setup
menu appears with Auto Talk
selected.
To turn on the base's ringer, set RINGER
to ON.
2. Press SELECT to change the auto
talk setting. Onor Offappears indi-
cating the selected setting.
3. Press CALL ID or return the handset
SETTING THE HANDSET’S
RINGER TONE/VOLUME
to the base to store the new setting.
You can select one of four different ring-
er tone/volume settings while the phone
is not in use. Press 8 or 9 on the
handset to increase or decrease to the
ringer level setting. Repeatedly press
8 or 9 until you hear the desired ring-
er setting. Each time you press 8 or
9, the ringer changes and the display
shows Ringer A High, Ringer A
Low, Ringer B High, or Ringer B
Low.
TURNING CALLER ID/
CALL WAITING ON/OFF
If you have Call Waiting with Caller ID
service, you can set the phone to show
Caller ID information for an incoming call
even while you are already on the
phone.
Follow these steps to turn the Caller ID/
Call Waiting feature on or off.
Note: Pressing 8 when the display
shows RingerAHighor 9 when the
display shows RingerBLowdoes not
10
43-1123.fm Page 11 Tuesday, September 5, 2000 11:13 AM
1. Lift the handset and hold down
CALL ID until Caller ID setup menu
appears with Auto Talkselected.
4. Press SELECT, then press CALL ID
and return the handset to the base
cradle to store the new setting.
2. Press 2 or 9 to select CIDCW
Note: In some areas, the area code is
necessary even for a local call. If you
live in such an area, do not enter the
area code.
(Caller ID/Call Waiting).
3. Press SELECT to change the Caller
ID/Call Waiting setting. On or Off
appears indicating the selected set-
ting.
4. Press CALL ID then return the hand-
set to the base to store the new set-
ting.
STORING YOUR AREA
CODE
By storing your local area code in the
phone's memory, the area code does
not appear in the Caller ID record dis-
play if it matches the one you stored.
Follow these steps to store your area
code.
1. Lift the handset and hold down
CALL ID until Caller ID setup menu
appears with Auto Talkselected.
2. Press 3 (or 9 twice) to select Area
Code.
3. Press SELECT, then enter your 3-
digit area code. If you make a mis-
take, repeatedly press 6or7 to
move the cursor over the incorrect
digit, then enter the correct number.
Note: If an area code is already
stored, it appears on the display. To
delete the area code, press DEL/CH
three times. Then enter your new
area code.
11
43-1123.fm Page 12 Tuesday, September 5, 2000 11:13 AM
OPERATION
Note: To use the speakerphone, you
must use the base keypad; to use the
handset, you must use the handset key-
pad.
Note: You can also dial the number be-
fore you press SPEAKER. If you make a
mistake, repeatedly press CLEAR to
erase each digit up to the wrong entry,
then enter the correct number. You can
also press and hold CLEAR for more
than one second to delete the entire
number.
MAKING A CALL
Using the Handset
To adjust the speakerphone's volume,
adjust VOLUME on the side of the base.
To make a call, lift the handset and
press TALK. Talk appears on the
handset's display and Handset in
Useappears on the base's display and
CHARGE/IN USE lights. Dial the num-
ber. You see the number as you dial,
then (after a few seconds) the call's
elapsed time.
To end a speakerphone call, press
SPEAKER again.
RECEIVING A CALL
When the phone receives a call, In-
Note: You can also dial the number be- coming Call appears. If you sub-
fore you press TALK. If you make a mis-
take, repeatedly press DEL/CH to erase
each digit up to the wrong entry, then
enter the correct number. You can also
press and hold DEL/CH for more than
one second to delete the entire number.
scribe to Caller ID service from your
telephone company, the phone compa-
ny sends information about the call, as
well as time and date, between the first
and second rings of every call you re-
ceive.
To end a call, place the handset on the
Notes:
base or press TALK.
• The base's display shows the num-
ber and name (if available). The
handset's display shows the date,
time, and number of calls received
from same caller in addition to the
number and name.
Using the Speakerphone
To make or answer a call using the
speakerphone, simply press SPEAKER.
SP-Phone appears on the base's dis-
play. Use the base's keypad to dial the
number. You see the number as you di-
al, then (after a few seconds) the call's
elapsed time.
• For the details of the Caller ID mes-
sage, see “Caller ID Messages” on
Page 21.
12
43-1123.fm Page 13 Tuesday, September 5, 2000 11:13 AM
To answer the call using the handset, lift
the handset off the base and press
TALK. If auto talk is on, just lift the hand-
set or press any key on the handset. To
answer a call using the speakerphone,
simply press SPEAKER.
USING MUTE
To talk to someone in the room while us-
ing the speakerphone without the per-
son on the other end of the phone line
hearing your conversation, press MUTE.
MUTEappears on the base's display.
Press MUTE again to resume your
phone conversation.
ADJUSTING THE
HANDSET VOLUME
Hint: When you talk over the speaker-
phone, the party that speaks first has
priority. If you are making a call in a
noisy environment, the phone might pick
up the noise and assume you are still
communicating, thus not switching back
to the person you are speaking with. If
this should happen, press MUTE so the
noise will not be picked up by the
phone's microphone. Press MUTE again
to release when it is your turn to speak.
To adjust the volume you hear through
the handset during a call, press 8 to in-
crease or 9 to decrease the volume.
The display shows VolumeMaximum,
Volume High, Volume Medium, or
VolumeLow.
Note: If you press 8 while the volume
is at the maximum or press 9 while the
volume is low, the setting does not
change.
SWITCHING BETWEEN
THE HANDSET AND THE
SPEAKERPHONE
SELECTING THE
CHANNEL
The phone scans 30 channels (frequen-
cy pairs used between the base and the
handset) and automatically selects a
clear channel each time you make or re-
ceive a call. If you hear other conversa-
tions or excessive noise during a call,
press DEL/CH to select a different chan-
nel. The display shows Scanning.
To switch to the speakerphone while
you are using the handset, press
SPEAKER on the base. When you hear
the conversation on the speakerphone,
press TALK on the handset.
To switch to the handset while you are
using the speakerphone, lift the handset
off the base. If the handset is away from
the base, press TALK, then press
SPEAKER.
Note: If the handset is too far from the
base, the channel might not change and
you hear an error beep. Move closer to
the base and try again.
13
43-1123.fm Page 14 Tuesday, September 5, 2000 11:13 AM
set and press REDIAL/PAUSE. The last
number dialed on the handset appears
below <Redial 1>. Press REDIAL/
PAUSE repeatedly until the desired num-
ber appears on the display, then press
TALK.
USING BOTH THE
HANDSET AND THE
SPEAKERPHONE
If someone else is using the speaker-
phone, press TALK on the handset to
join the conversation. If someone else is
using the handset, press SPEAKER on
the base to join the conversation. Con-
ference appears on the base's dis-
play and CHARGE/IN USE lights.
To dial the last number dialed on the
base, press REDIAL on the base. The
last number dialed on the base appears
on the base's display. Then press
SPEAKER. You can redial only the last
number on the base.
During the call, one person can hang up
and let the call continue at the other key-
pad. Or, both people can hang up to end
the call.
Notes:
• The redial memory is separate for
each keypad. You cannot redial a
number you dialed on the handset
keypad using REDIAL on the base,
and vice versa.
Note: If you hear a high-pitched noise
from the base's speaker, the handset
and the base are too close together.
• The redial memory holds up to 32
digits, so you can redial any long-
distance number as well as local
numbers.
USING FLASH
Flash performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting. For
example, if you have Call Waiting, press
FLASH to answer an incoming call with-
out disconnecting the current call. Press
FLASH again to return to the first call.
• The redial memory also holds pause
entries (see “Entering a Pause” on
Page 19).
USING TONE SERVICES
ON A PULSE LINE
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by following
these steps.
USING REDIAL
1. Be sure DIAL MODE P- -T is set to P-.
To quickly dial any of the last three num-
bers dialed on the handset, lift the hand-
14
43-1123.fm Page 15 Tuesday, September 5, 2000 11:13 AM
2. Dial the service's main number.
To end an intercom call, press TALK on
the handset, press SPEAKER on the
base, or hang up the handset.
3. When the service answers, press
TONE/ . Any additional numbers
you dial are sent as tone signals.
If a call comes in during an intercom
conversation, only the base rings, but
the person at the handset can also hear
the ring through the intercom. Either per-
son can answer the call by pressing
TALK or SPEAKER once to end the inter-
com call, then pressing TALK or SPEAK-
ER again to answer the call.
4. When you hang up, the phone auto-
matically resets to pulse dialing.
USING PAGE/INTERCOM
You can use the phone as a two-way
pager and intercom between the base
and the handset. This is useful if the
handset is away from the base and you
want to locate it, or if you want to have a
conversation between someone with the
handset and someone at the base.
Note: The intercom does not operate if
the party being paged is already on a
call.
TRANSFERRING A CALL
BETWEEN THE HANDSET
AND THE BASE
To page the base from the handset,
press INTCM. The base and handset
ring. Paging appears on the base's
display and PagingBaseappears on
the handset's display. Press SPEAKER
or INTERCOM on the base to answer the
page. Both displays change to Inter-
com.
You can use the phone's intercom fea-
ture to transfer a call between the hand-
set and the base for a three-way
conversation.
To transfer a call from the handset to the
base, press INTCM. The call is placed on
hold, CHARGE/IN USE blinks, and
Hold and Paging Base appear on
the handset's display. When the person
at the base answers, press TALK. The
call is released from hold and trans-
ferred to the base. To bring the handset
back into the conversation for a three-
way conference, press TALK again.
To page the handset from the base,
press INTERCOM. The handset and
base ring. Paging Handsetappears
on the base's display and Pagingap-
pears on the handset's display. Press
TALK or INTCM on the handset to an-
swer the page. Both displays change to
Intercom.
In either case, if the called party does
not answer within 1 minute, the paging
stops. Press INTCM or INTERCOM again
to restart paging.
15
43-1123.fm Page 16 Tuesday, September 5, 2000 11:13 AM
To transfer a call from the base to the
handset, press INTERCOM. The call is
placed on hold, CHARGE/IN USE
blinks, and Holdand PagingHand-
set appear on the base's display.
When the person with the handset an-
swers, press SPEAKER. The call is re-
leased from hold and transferred to the
handset and the display changes to
Handset in Use. To bring the base
back into the conversation for a three-
way conference, press SPEAKER again.
To connect the headset, open the rub-
ber cover marked on the side of the
handset, then insert the headset's plug
into the jack.
Headset
Jack
Notes:
• Connecting a headset disconnects
the handset's earpiece and micro-
phone.
OUT OF RANGE
If you have the handset out of the base's
range while a call is in progress, noise
increases. Return to the base’s range
within 30 seconds, then you can resume
your phone conversation.
• 8 or 9 on the handset also con-
trols the connected headset's vol-
ume, but maximum setting is not
available on the headset.
• If you place the handset on the base
to recharge it while the headset is
connected, be sure the handset
seats properly.
If you keep the handset out of the base’s
range for 30 seconds or more, the call is
disconnected. However if you are in 3-
way conference call, the speakerphone
call remains connected.
With a headset connected, you can
make or answer calls as usual using the
keys on the handset. You can also make
or answer calls by pressing the SPEAK-
ER button located on the base.
USING A HEADSET
You can talk with handsfree conve-
You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for great-
er convenience.
nience using an optional headset that
3
32
has a / -inch (2.5-mm) plug. Your local
RadioShack store has a variety of suit-
able headsets to chose from.
When you finish using the headset, dis-
connect it from the handset and close
the rubber cover to protect the jack.
16
43-1123.fm Page 17 Tuesday, September 5, 2000 11:13 AM
3. Select an empty memory location
(or the one you want to replace) by
using 8 or 9 to scroll through the
list or entering the location number
(01-20). Precede a single-digit num-
ber with a 0 (01, for example).
MEMORY DIALING
You can store up to 20 numbers in the
handset's memory and another 10 in the
base's memory, then dial a stored num-
ber by pressing a memory location num-
ber. You can also store a name with
each number in the handset's memory.
The base has four one-touch dial memo-
ries in addition.
Notes:
• If the phone sounds five quick
beeps, you have made an entry
error and the number was not
stored. Re-enter the location
number correctly.
Each number you store can be up to 20
digits long, and each name can be up to
13 characters.
4. Press SELECT. Store Name
appears.
You cannot dial a number stored in one
memory location (the base or the hand-
set) using the keypad on the other.
• If you do not want to enter a
name, skip to Step 6.
5. To enter a name, use 8 or 9 to
select the characters and 6 or 7
to move the cursor to the next char-
acter space. Repeatedly press 9
to view the characters in alphabeti-
cal order. The display shows upper-
case letters first, then lowercase
letters, numbers, and special char-
acters. Press 8 to view the charac-
ters in reverse order. You can hold
down 8 or 9 to scroll rapidly
through the characters.
Storing a Name and Number in
Memory
Notes:
• An error tone sounds and the phone
exits the storing process if you wait
more than 20 seconds between key
presses.
• If you receive a call during memory
entry, the phone exits the storing
process.
If you make a mistake, move the
cursor over the error, then enter the
correct character, or press DEL/CH
to delete a character. To delete all
the characters, hold down DEL/CH
for at least 1 second.
To store a name and number in the
handset, follow these steps:
1. Lift the handset.
2. Hold down MEM until Memory
Store and a list of memory loca-
tion numbers (and names, if any)
appear.
6. Press SELECT. Store Number
appears.
17
43-1123.fm Page 18 Tuesday, September 5, 2000 11:13 AM
7. Enter the phone number and any
tone or pause entries (see “Entering
a Pause” on Page 19).
To clear a stored number, simply store a
new number in its place. Or, hold down
MEMORY until Store Number ap-
pears. Then press MEMORY and the
memory location number (0-9) or the
one-touch dial button (M1-M4) you want
to clear. A tone sounds and Memoryn
If you make a mistake, use the
same method to correct it as
described in Step 5.
8. Press SELECT. The phone beeps Storedor MemoryMnstored appears
and Memory nn Stored (nn
stands for the memory location
number you assigned) appears.
After 2 seconds, Memory Store
appears. Repeat Steps 3-8 to store
more numbers.
on the display.
Use the supplied memory directory
sticker to record your stored numbers.
Peel the backing from the sticker and at-
tach it to the base.
9. When you finish, press MEM.
To replace a stored number, store a new
one in its place using the same steps
above.
To store number in the base, follow
these steps:
1. Hold down MEMORY until Store
Numberappears on the base's dis-
play.
Editing or Deleting a Number in
the Handset's Memory
Follow these steps to edit or delete a
memory number.
2. Enter the phone number and any
tone or pause entries (see “Entering
a Pause” on Page 19).
1. Lift the handset.
If you make a mistake, press CLEAR
to exit the memory store operation.
Start again at Step 1.
2. Hold down MEM until Memory
Store and a list of memory loca-
tion numbers appear on the display.
3. Press MEMORY again. Location
No. appears. Enter the memory
location number (0-9) or the one-
touch dial button (M1-M4) where you
want to store the number. A tone
sounds and MemorynStoredor
Memory Mn Stored appears on
the display to indicate that the num-
ber is stored.
3. Choose a memory location (01-20)
by pressing a number or by repeat-
edly pressing 8 or 9.
4. Press SELECT. A menu appears
with the three options listed below.
Press 8 or 9 to highlight the
desired option then press SELECT to
choose it.
18
43-1123.fm Page 19 Tuesday, September 5, 2000 11:13 AM
Menu Options:
number (01-20) or repeatedly press 8
or 9.
• Edit Memory nn — edit the
record as described in Steps 5
through 8 of “Storing a Name and
Number in Memory” on Page 17.
To see the stored phone numbers, press
7. An arrow to the right of the number
means it is longer than 14 digits. Press
7 again to see the rest of the number.
• DeleteMemorynn— the display
prompts you to confirm the deletion.
Move the cursor to Yes, then press
SELECT or DEL/CH. The phone
beeps, and Memorynn Deleted
appears.
Repeatedly press 6 to return to the
name display.
To exit the memory number list, press
MEM.
• GoBack— returns you to the list of
memory numbers.
To see a stored name and phone num-
ber at the same time, press SELECT
when the cursor is by a memory location
number. To exit this display, hold down
DEL/CH until the display clears.
Entering a Pause
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect.
Dialing a Memory Number
To dial a number stored in handset's
memory, lift the handset and press MEM.
The list of memory location numbers ap-
pears. Choose a memory location (01-
20) by pressing a number or by repeat-
edly pressing 8 or 9, then press
TALK.
To enter a 2-second pause, press REDI-
AL/PAUSE (REDIAL on the base). Pap-
pears on the display when you enter a
pause in the memory. You can add
more pause entries for a longer pause.
You can also dial a memory number af-
ter pressing TALK. Press MEM (the dis-
play does not change but the phone is in
memory recall mode) then enter a mem-
ory location number.
Reviewing Memory Numbers
(Handset Only)
To dial a number stored in the base's
memory, press MEMORY. Location
No.appears. Press a number key (0-9);
the display shows the number contained
in the selected memory location. Press
SPEAKER to dial the number on the dis-
To review your memory numbers, press
MEM. The list of memory location num-
bers (01-20) and the name stored with
each number (or <Memory nn> if you
did not store a name) appears. To view
several a memory location, press its
play.
19
43-1123.fm Page 20 Tuesday, September 5, 2000 11:13 AM
Note: If you select an empty memory lo-
cation, no number appears.
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the phone compa-
ny sends information about the call, as
well as the time and date, between the
first and second rings of every call you
receive. This information appears after
the second ring on both the handset's
and the base's displays. The display
also shows if caller information is un-
available or if the name and number
were blocked by the caller (see “Caller
ID Messages” on Page 21).
To dial a number stored in one-touch
dial memory, simply press the button
(M1-M4). You do not need to press
SPEAKER to dial the number in one-
touch dial memory.
Note: If you select an empty one-touch
dial memory, the base beeps five error
beeps.
Chain-Dialing Service Numbers
If you subscribe to Call Waiting with
Caller ID, you will hear a tone through
the handset when a call comes in, then
the Caller ID record appears. If you want
to answer the incoming call, press
FLASH. To resume the previous phone
conversation, press FLASH again.
For quick recall of numbers for special
services (such as bank by phone), store
each group of numbers in its own mem-
ory location. Dial the service's main
number first. Then, at the appropriate
place in the call, press MEM (or MEMO-
RY on the base) and enter the number
for the location where the additional in-
formation is stored.
The handset has Caller ID memory to
store the information received up to 50
Caller ID records for later review. It
stores the information even when you
answer the call using the speakerphone.
Testing Stored Emergency
Numbers
If the Caller ID memory becomes full,
any new call replaces the oldest call's
record.
If you store an emergency service's
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
The base's NEW CALL indicator also
flashes when the phone receives a call
with Caller ID information and you have
not yet reviewed it. Use the handset's
Caller ID memory to review the informa-
tion about the call(s) received.
20
43-1123.fm Page 21 Tuesday, September 5, 2000 11:13 AM
Reviewing Caller ID Records
(Handset Only)
Caller ID Messages
Display
Description
To review the Caller ID records in the
handset's memory, lift the handset and
press CALL ID. The number of new Call-
er ID records, if any, and the total num-
ber of records appears.
Shows the number
of new Caller ID
records (records you
have not reviewed)
and the total num-
ber of records.
New: XX
Total: XX
Note: If the handset is faceup on the
base, it shows the number of Caller ID
records, so you can see if you have new
records to review.
The caller has
blocked the Caller ID
information from
being sent.
Private Name
or
Private Number
The caller is not
within a Caller ID
service.
Unknown Name
or
Unknown Number
Repeatedly press 9 to scroll through
the Caller ID records from the newest to
the oldest, or 8 to scroll back through
the records. To scroll quickly through the
records, hold down 8 or 9.
Appears if there was
an error during the
transmission of
Incomplete Data
Caller ID informa-
tion. Minor electrical
disturbances can
When you scroll past the last record,
Endappears. When you scroll past the
first record, the record totals appear.
affect Caller ID infor-
mation. Occasional
errors are normal. If
the phone frequently
displays Incomplete
Data, contact your
local telephone com-
pany or RadioShack
store for assistance.
The top line of each record shows the
date, time and the number of calls from
that number. The second line shows the
caller's name, and the third line shows
the caller's phone number.
Note: Calls cannot be reviewed or
stored in the base.
Appears when you
scroll past the oldest
Caller ID record.
End
Dialing Numbers From a Caller
ID Record (Handset Only)
To dial a local number stored in a Caller
ID record, recall the record, then press
TALK. If it is a long distance call, press 1
before you press TALK.
21
43-1123.fm Page 22 Tuesday, September 5, 2000 11:13 AM
Note: If a Caller ID record does not con-
tain a phone number (if it was blocked
by the caller, for example) you cannot
dial from that record.
To delete all the records at once, press
CALL ID so the record totals appear,
then press DEL/CH. DeleteAll?ap-
pears, prompting you to confirm the de-
letion. Move the cursor to Yes, then
press SELECT or DEL/CH.
Storing a Caller ID Record to
Memory (Handset Only)
To store the name and number from a
Caller ID record into a handset's memo-
ry location, recall the record you want to
store. Press MEM, then Select Lo-
cationappears.
Choose a memory location (01-20) by
pressing a number or by repeatedly
pressing 8 or 9, then press SELECT.
If the selected location is empty, the
phone beeps to confirm that it stored the
number, then the Caller ID record ap-
pears. If a record exists in the selected
location, Replace Memory? ap-
pears, prompting you to confirm the re-
placement. Move the cursor to Yes or
No, then press SELECT.
Deleting Caller ID Records
(Handset Only)
You can delete Caller ID records individ-
ually or all at once.
To delete a single record, recall it, then
press DEL/CH. DeleteMessage?ap-
pears, prompting you to confirm the de-
letion. Move the cursor to Yes, then
press SELECT or DEL/CH.
22
43-1123.fm Page 23 Tuesday, September 5, 2000 11:13 AM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, these
suggestions might help.
Problem
Suggestion
Low volume or unusual
sounds.
Someone has picked up another phone on the same line.
Hang up the other phone.
Press DEL/CH to change the channel.
Keep the handset away from computers, remote control
toys, wireless microphones, alarm systems, intercoms, room
monitors, fluorescent lights, and electrical appliances.
Severe noise interference.
Move the handset to another location or turn off the source of
interference.
Lift the base's antenna to a vertical position.
The phone cannot be oper-
ated at a useful distance from
the base because the signal
becomes weak or noisy
(handset's range has
Be sure neither antenna is touching a metal surface.
Return the handset to the cradle, and recharge the battery
pack.
Replace the battery pack if necessary (see “Replacing the
Battery Pack” on Page 26).
decreased).
Be sure the base's phone line cord and AC adapter are cor-
rectly and securely connected, and the battery pack is
charged.
The phone does not work or
works poorly.
Check the charging contacts on the handset and base.
If they are dirty, clean them with a pencil eraser.
The handset battery pack
does not charge.
Be sure the battery pack is connected correctly.
Replace the battery pack.
Move the handset closer to the base.
The handset does not ring or Lift the base's antenna to a vertical position.
receive a page.
Be sure the battery pack is charged. (If the battery power is
too low, it does not have enough power to light the display.
The handset does not ring or Move the base away from other electrical devices and
receive a page.
sources of noise.
23
43-1123.fm Page 24 Tuesday, September 5, 2000 11:13 AM
Problem
Suggestion
Move the handset closer to the base.
Lift the base's antenna to a vertical position.
Be sure the battery pack is charged. (If the battery power is
too low, it does not have enough power to light the display.)
The handset stops working or
works poorly during a call.
If the base loses power while the handset is away, the secu-
rity access-protection code might change. Restore power to
the base, then place the handset back on the base. The
CHARGE/IN USE indicator lights, indicating that the code is
set again.
Check the charging contacts on the handset and base. If
they are dirty, clean them with a pencil eraser.
Low Battery flashes
on the display every few sec-
onds.
Be sure the battery pack is correctly connected.
Let the phone ring twice before you answer so the system
has time to record the Caller ID information.
You have an incoming call,
but do not receive any Caller Check that the system is correctly and securely connected.
ID information.
Call your phone company to verify that your Caller ID service
is active.
If you still have problems, disconnect the phone. If other phones on the same line work proper-
ly, the fault is in this phone or its installation. If you cannot find the problem, take your phone to
your local RadioShack store for assistance.
24
43-1123.fm Page 25 Tuesday, September 5, 2000 11:13 AM
CARE AND MAINTENANCE
Your RadioShack Digital 900 MHz Dual Keypad Cordless Speakerphone is an ex-
ample of superior design and craftsmanship. The following suggestions will help
you care for your phone so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids might
contain minerals that can corrode the electronic circuits.
Use and store the phone only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the phone away from dust and dirt, which can cause premature
wear of parts.
Handle the phone gently and carefully. Dropping it can damage circuit
boards and cases and can cause the phone to work improperly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your phone’s electronic
parts.
Wipe the phone base and handset with a damp cloth occasionally to
keep them looking new. Do not use harsh chemicals, cleaning solvents,
or strong detergents to clean the phone.
Modifying or tampering with the phone’s internal components can cause a malfunc-
tion and might invalidate its warranty and void your FCC authorization to operate it.
If your phone is not performing as it should, take it to your local RadioShack store
for assistance. If the trouble is affecting the telephone lines, the phone company
can ask you to disconnect your phone until you have resolved the problem.
25
43-1123.fm Page 26 Tuesday, September 5, 2000 11:13 AM
Follow these steps to replace the batter-
ies.
REPLACING THE
BATTERY PACK
1. Press down and slide off the battery
pack compartment cover.
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 8, the battery pack should last
about one year. If the battery pack does
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a new 3.6-volt, 600 mAh battery pack
with a connector that fits the socket in
the battery compartment. You can order
a replacement battery pack through your
local RadioShack store.
2. Lift the battery pack out of the com-
partment, then gently pull on the
battery connector to disconnect it.
3. Insert the new battery pack's con-
nector into the socket in the com-
partment and place the battery pack
into the compartment.
4. Replace the cover.
Install the new battery pack as de-
scribed below, then charge it for about
24 hours (see “Connecting and Charg-
ing the Battery Pack” on Page 8).
If you have trouble replacing the battery,
take the phone to your local RadioShack
store for assistance.
Important: The EPA certi-
®
Warning: Dispose of old batteries
promptly and properly. Do not burn or
bury them.
fied RBRC Battery Recy-
cling Seal on the nickel-
cadmium (Ni-Cd) battery in-
dicates RadioShack is vol-
Cautions:
untarily participating in an industry
program to collect and recycle these
batteries at the end of their useful life,
when taken out of service in the United
States or Canada. The RBRC program
provides a convenient alternative to
placing used Ni-Cd batteries into the
trash or the municipal waste stream,
which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-
843-7422) for information on Ni-Cd bat-
tery recycling and disposal bans/restric-
tions in your area. RadioShack’s
involvement in this program is part of the
company’s commitment to preserving
our environment and conserving our
natural resources.
• Use only fresh batteries of the
required size and recommended
type.
• Be careful not to short the battery by
touching the connector's pins with
conducting materials, such as rings,
bracelets, and keys. The battery
pack or conductor might overheat
and burn.
Note: To avoid losing memory numbers,
install and begin charging the new bat-
tery pack within 30 seconds.
26
43-1123.fm Page 27 Tuesday, September 5, 2000 11:13 AM
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Some cordless telephones operate on
frequencies that might cause interfer-
ence to nearby TVs and VCRs. To mini-
mize or prevent such interference, the
base of the cordless telephone should
not be placed near or on top of a TV or
VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your telephone service.
Your telephone has built-in surge pro-
tection to reduce the risk of damage
from surges in telephone line and power
line current. This protection meets or ex-
ceeds FCC requirements. However,
lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it. Try to
eliminate the interference by:
• moving your phone away from the
receiver
• connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• contacting your local RadioShack
store for help
27
43-1123.fm Page 28 Tuesday, September 5, 2000 11:13 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
We Service What We Sell
RadioShack Corporation
Fort Worth, Texas 76102
UCZZ01660BA
Printed in China
09A00
|