INSTALLATION GUIDELINES
Stereo or Mono Inputs
Connecting to standard AC power
MONO OPERATION
Your Pyle Pro amplifier can be operated in Stereo, Mono or
Bridged mode, depending on the input source. If the input
signal is mono, slide the Stereo/Mono/Bridged selector
switch to MONO and the signal will be routed through both
channels. If you wish to run the amplifier in bridged output
mode, slide the switch to Bridged.
After making all other connections, set the POWER switch
to OFF position. Then connect the power cord to a standard
AC outlet.
Connecting the GND (Ground) screw terminal
Connecting a mixer or preamplifier may cause excessive
noise or hum in the amplifier output. To prevent this,
connect one end of a low-capacitance shielded wire to the
amplifier’s ground screw (on the rear panel). Then connect
the other end of this wire to the ground terminal on the
mixer or preamplifier enclosure.
SWITCH IN “MONO” POSITION
MONO
CH A
STEREO BRIDGE
CH B
Mounting the amplifier
This amplifier is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
Speaker connections
CH B
CH A
PREAMP OR MIXER
OUTPUT
You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to
Channel A and/or Channel B of the amplifier. If you connect
two pairs of speakers, be sure to follow these guidelines:
CH
B
CH
A
–
+
+
–
CIRCUIT
BREAKER
INPUTS
CH
–
+
CH
B
A
BRIDGE
AC POWER IN
Tightly secure four mounting screws (not supplied) through
these fours slots and into your standard electronics equipment
rack.
CH
B
CH
A
MONO
S
T
E
R
E
O
B
R
I
D
G
E
GND
GROUND LIFT
LIFT
GROUND
OUTPUT
CH
B
CH A
–
+
+
–
• Speakers which are connected to the same channel are
part of a pair, and must be of the same impedance.
CIRCUIT
BREAKER
INPUTS
CH A
GROUND
SCREW
LOW CAPACITANCE SHIELDED WIRE
–
+
CH
B
BRIDGE
AC POWER IN
CH
B
CH
A
MONO
STEREO BRIDGE
GND
GROUND LIFT
LIFT
Turning the amplifier on
1. Turn on the audio input source equipment which is
connected to the amplifier INPUT jacks.
• Speakers connected to different channels are NOT part
of a pair, and can be of different impedances.
Input connections
GROUND
These amplifiers accept a broad range of input sources,
including Compact Disc (CD) players; Cassette, Reel-to-Reel
or other tape players; Radio Tuners; Equalizers; Signal
Processors.
1. Prepare the speaker wire by removing about 1 inch of
insulation from the end of the speaker wire you intend to
connect to the amplifier. Then twist the exposed wire to
secure all the wire strands.
2. Set the amplifier’s Channel A and Channel B output level
gain controls to the minimum level settings.
MONO SIGNAL SOURCE
USE
CHANNEL A
INPUT ONLY
Connecting a CD or tape player or tuner
In a normal installation, one would use the RCA JACKS for
connecting a CD player, tape player or tuner.
3. Push in the power switch to turn the amplifier on.
NOTE: Use 16-gauge speaker wire for lengths up to25
feet; 14-gauge wire for lengths over 25 feet. It is
recommended that you use the shortest length of wire
possible.
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
Using the power meters
OUTPUT
CH
B
CH
A
–
+
+
–
The meter pointer position indicates the amplifier output
power. For ease of reading in dark environments, the meter
is illuminated.
CIRCUIT
BREAKER
INPUTS
CH
Bridged Mode Operation
This amplifier can operate in a mono bridged output mode, if
your speakers can handle the following power output levels:
–
+
CH
B
A
BRIDGE
AC POWER IN
2. Connect the speaker wires to the speaker's positive and
negative terminals.
CH
B
CH
A
MONO
STEREO BRIDGE
GND
GROUND LIFT
LIFT
GROUND
NOTE: Most speaker terminals are either color-coded
or have a mark that indicates the terminal's polarity.
Usually positive terminals are red or have a plus symbol
(+), and negative terminals are black or have a minus
symbol (-).
PT-3200: 600 watts
PT-4000: 800 watts
use RCA jacks
Using the Left and Right Output Level controls
Rotate output level gain clockwise to increase, or counter-
clockwise to decrease the output power. To get the best
performance with the least sound distortion, always adjust
the output level gain so the meter's pointer does not
continuously exceed the extreme right of the meter's scale.
As shown in the diagram below, connect the speaker's positive
(+) to the amplifier's red speakers left (A/B) terminals and
negative (-) to red speakers right (A/B) terminals.
CD PLAYER, TAPE PLAYER
OR TUNER
3. Connect the speaker wires to the amplifier's left and
right speaker terminals according to the terminal color
polarity.
The speaker right (+) on the amplifier is used as a negative (-)
terminal for a bridged connection.
CAUTION: It is possible to overdrive the amplifier by
setting output level gain too high, which may cause
damage or failure.
Connecting an equalizer or external signal processor
Connect the processor’s OUT to the amplifier’s INPUT
connectors.
NOTE: The extra amplifier output of 6.35mm phone
jacks can not be used for the bridged connection. It can only
be used in normal (non-bridged) operation as a stereo speaker
output.
STEREO OPERATION
OUTPUT
+
CH
B
CH
A
–
+
–
CIRCUIT
BREAKER
SWITCH IN “STEREO” POSITION
About the internal clip circuitry
INPUTS
CH A
–
+
CH
B
MONO
BRIDGE
CH B
CH A
Special clip circuitry incorporated into your Pyle Pro
amplifier’s design protects the amplifier and speaker system
from being damaged from overdriving power.
AC POWER IN
STEREO
BRIDGE
MONO BRIDGED OPERATION
SWITCH IN “BRIDGED” POSITION
CH
B
CH
A
MONO
STEREO BRIDGE
GND
GROUND LIFT
LIFT
GROUND
MONO
CH B
CH A
STEREO
BRIDGE
Under normal conditions, the amplifier’s clip indicator will
flicker as the output power momentarily exceeds the level
as set by the output level gain selector.
EQ OR MIXER
CH B
CH A
However, under excessive output conditions, the clip
indicator lights remain on continuously, alerting you that
the special clip circuitry has become active. When this
occurs, you should simply reduce the output power level
by rotating the Master Volume control counterclockwise.
OUTPUT
CH
B
CH A
–
+
+
–
CIRCUIT
DO NOT USE
-OR–
BREAKER
INPUTS
CH A
BLACK TERMINALS
–
+
CH
B
BRIDGE
AC POWER IN
CH
B
CH
A
MONO
STEREO BRIDGE
OUTPUT
GND
OUTPUT
GROUND LIFT
LIFT
CH
B
CH A
–
+
+
–
CH
B
CH
A
–
+
+
–
GROUND
CIRCUIT
CIRCUIT
BREAKER
BREAKER
INPUTS
CH A
INPUTS
CH A
–
+
CH
B
BRIDGE
–
+
CH
B
AC POWER IN
BRIDGE
AC POWER IN
CH
B
CH
A
MONO
STEREO BRIDGE
GND
GROUND LIFT
LIFT
CH
B
CH
A
MONO
GROUND
STEREO BRIDGE
GND
GROUND LIFT
LIFT
GROUND
STEREO SIGNAL SOURCE
EQ OR MIXER
use XLR/6.35 mm
combo jacks
MONO SIGNAL SOURCE
USE
CHANNEL A
INPUT ONLY
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
2 – PYLE PRO PT3200/4000 Amplifier Owner’s Manual
PYLE PRO PT3200/4000 Amplifier Owner’s Manual - 3
Caring for your Pyle Pro Amplifier
Limited Warranty
Your Pyle Pro Amplifier is an example of superior design
and craftsmanship. The following suggestions will help you
care for your amplifier so you can enjoy years of use:
All PYLE PRO products are carefully constructed and tested before shipment.
Units purchased in the USA are warranted to be free of defects in material
and workmanship for two (2) years from the date of purchase. This warranty
is limited to the original retail purchaser of the amplifier.
• Keep the amplifier dry. If it gets wet, wipe immediately.
• Use the amplifier only in well-ventilated installations.
• Handle the amplifier gently and carefully - do not drop!
• Keep the amplifier away from dust and dirt.
• Wipe occasionally with a damp cloth to keep it looking
new. Do not use harsh chemicals, solvents or
detergents!
Should the unit fail due to factory defects in material or workmanship, your
unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must
appear on the outside of your package and on all paperwork relating to your
return.
When returning the unit to us for warranty service, it must be carefully packed
and shipped, prepaid, to:
Resetting the circuit breaker
This amplifier employs a circuit breaker for protection from
power surges and short circuits. If the amplifier suddenly
turns off or will not turn on, check the circuit breaker. If
it is tripped, check and correct for a short or overload
condition. Wait for the amplifier to cool, then press the
circuit breaker RESET button on the back of the amplifier.
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
•
•
A copy of your sales receipt or other proof of purchase
A brief letter, indicating the problem you are experiencing with the
product
Include in your letter your return address, daytime phone number and
R.A. number
Also include a check or money order for $15.00 for return shipping,
handling and insurance, or provide your Visa/MC number with
expiration date.
Resetting the circuit breaker
•
•
This amplifier employs a circuit breaker for protection from
power surges and short circuits. If the amplifier suddenly
turns off or will not turn on, check the circuit breaker. If
it is tripped, check and correct for a short or overload
condition. Wait for the amplifier to cool, then press the
circuit breaker RESET button on the back of the amplifier.
Our obligation under this warranty is limited to the repair or replacement of
the defective unit when it is returned to us prepaid. This warranty will be
considered void if the unit was tampered with, improperly serviced or subject
to misuse, neglect or accidental damage.
Amplifier Specifications
PT3200
PT4000
Input Impedance, balanced (unbalanced)
Continuous Output Power
20 k-Ohms (10 k-Ohms)
20 k-Ohms (10 k-Ohms)
Stereo Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 4 Ohms
200W x 2
300W x 2
230W x 2
350W x 2
1600W x 2
260W x 2
400W x 2
300W x 2
450W x 2
2000W x 2
Maximum Power, 8 Ohms
Maximum Power, 4 Ohms
Peak Power, 8 Ohms
Bridged Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 8 Ohms
500W x 1
600W x 1
3200W x 1
700W x 1
800W x 1
4000W x 1
Peak Power
THD at rated output power
0.1%
10 Hz to 50 kHz
1.0V
0.1%
10 Hz to 50 kHz
1.0V
Frequency Response +/– 3 dB
Input Sensitivity for rated output power
Signal-to-Noise Ratio A-Weighted
100 dB
100 dB
Speaker Impedance
Stereo
Bridged
4-16 Ohms
8-16 Ohms
4-16 Ohms
8-16 Ohms
Power Requirement
120 VAC, 60 Hz
120 VAC, 60 Hz
Dimensions H x W x D, inches
(mm)
3 15/32 x 19 x 14
(88 x 482 x 355)
3 15/32 x 19 x 14
(88 x 482 x 355)
Weight, lbs (kg)
30.6 (13.96)
33.0 (15.1)
4 – PYLE PRO PT3200/4000 Amplifier Owner’s Manual
PYLE PRO PT3200/4000 Amplifier Owner’s Manual - 5
|