M32186T2-PTC
Converter for In-circuit Connection (for M32186FxxFP)
User’s Manual
Keep safety first in your circuit designs!
1. Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention
against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
2. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application
examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor for the latest product information before purchasing a product listed herein. The information described here may contain
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home
page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any
damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or
reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the
products contained therein.
Precautions to be taken when using this product
1. This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
2. In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
3. Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
4. This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.2.00
Oct. 16, 2006
(1/6)
REJ10J0971-0200
5. Connection Procedure
Connection to the M32100T-SDI-E or M32170T-SDI
5.1 For M32100T-SDI-E or M32170T-SDI.
(1) Mount the NQPACK144SD on the user system
(2) Connect the YQPACK144SD on the NQPACK144SD.
(3) Secure the four corners of the YQPACK144SD with the
YQ-GUIDE’s.
Interface cables of the pod probe
(7)
M3T- PTC- CNV
(separately available)
(6)
(4) Mount the M32186T2-PTC on the YQPACK144SD.
(5) Set the clock select switch.
Clock select switch
(5)
(6) Mount the M3T-PTC-CNV on the M32186T2-PTC.
M32186T2- PTC
(4)
(7) Connect the emulation pod probe to the M32186T2-PTC
via the SDI MCU control interface cable and the SDI trace
interface cable.
YQ-GUIDE(x4)
(3)
YQPACK144SD
NQPACK144SD
(2)
(1)
144-pin 0.5mm pitch
(144P6Q-A) foot pattern
: No.1 pin
●
Be sure to match the position of No. 1 pin of the foot pattern and each part.
Figure 5.1 Connection Procedure (1)
(3/6)
Connection to M32100T2-SDI-E,
M32100T3-SDI-E or M32100T5-SDI-E
5.2 For M32100T2-SDI-E, M32100T3-SDI-E or
M32100T5-SDI-E.
(1) Mount the NQPACK144SD on the user system
Emulator main unit or
Emulator Probe
(2) Connect the YQPACK144SD on the NQPACK144SD.
(3) Secure the four corners of the YQPACK144SD with the
YQ-GUIDE’s.
(4) Mount the M32186T2-PTC on the YQPACK144SD.
(5) Set the clock select switch.
(6)
Clock select switch
(5)
(6) Connect the emulator probe to the M32186T2-PTC.
.
M32186T2-PTC
(4)
YQ-GUIDE(x4)
(3)
YQPACK144SD
NQPACK144SD
(2)
(1)
144-pin 0.5mm pitch
(144P6Q--A) foot pattern
●: No.1 pin
Be sure to match the position of No.1 pin of foot pattern and each part
Figure 5.2 Connection Procedure (2)
5.3 On-board Evaluation
(1) Mount the NQPACK144SD on the user system
(2) Mount the M32186FxxFP on the NQPACK144SD.
(3) Mount the HQPACK144SD on the NQPACK144SD.
HQPACK144SD
(separately available)
(3)
M32186FxxFP
(separately available)
(2)
NQPACK144SD
(1)
144-pin 0.5mm pitch
(144P6Q-A) foot pattern
: No. 1 pin
●
Be sure to match the position of No. 1 pin of the foot pattern and each part.
Figure 5.3 Connection Procedure (3)
(4/6)
6. Selecting a Clock
Mount an oscillator to X2 as
shown in the diagram printed on
the boar.d
With the M32186T2-PTC, it is possible to select a clock supply
to the MCU by the clock select switch (SW1). Select a clock
supply as shown below.
However, when used with the M32186T2-PTC, the clock
cannot be supplied from the user system.
X2 socket
Connected to XIN pin of MCU
R1 0
Connected to XOUT pin of MCU
C1
C2
R 4
R1 0
R4
C1
C2
(1) 8 MHz:
:
:
:
:
1MΩ
510Ω
27pF
27pF
Supplies the clock (X1: 8 MHz) to the MCU from the
oscillator on the M32186T2-PTC board
(2) SOCKET:
Supplies the clock to the MCU from the socket (X2) for
mounting an oscillator on the M32186T2-PTC board. By
mounting an oscillator to the X2 socket of the MCU, it is
possible to change the operating frequency.
Figure 6.1 shows the connecting the X2 socket and the
MCU.
Figure 6.1 Connection diagram of X2 socket
7. External Dimensions and a Sample Foot Pattern of the M32186T2-PTC
16
85
M32192T2 -PTC REV . A
MADE IN JAPAN
SOCKET
SW1
M Hz
8
23
19
0.25
for SL
ø
3.2
Hole for
soldering NQ
ø
3- 1.0
7
0.5
: No.1 pin
●
Unit: mm
Figure 7.1 External dimensions and a sample foot pattern of the M32186T2-PTC
(5/6)
8. Precautions
CAUTION
Cautions to Be Taken for Emulator:
z For debugging, use this product in the combination with the SDI emulator, M32100-SDI-E, M32170T-SDI,
M32100T2-SDI-E, M32100T3-SDI-E or M32100T5-SDI-E.
z When using with the M32100T-SDI-E or M32170T-SDI, the following restrictions are applied according to the
MCU operating frequency. The M32186T2-PTC is recommended to use with the M32100T3-SDI-E or
M32100T5-SDI-E.
- More than 66 MHz:
Compared with the M32100T2-SDI-E, M32100T3-SDI-E, or M32100T5-SDI-E, more loss of trace information
occurs.
- 66 MHz or less:
Same as the M32100T2-SDI-E, M32100T3-SDI-E or M32100T5-SDI-E.
z When using with the M32100T-SDI-E or M32170T-SDI, separately available M3T-PTC-CNV is required.
z When connecting to the M32100T-SDI-E or M32170T-SDI, connect the both cables for connecting the emulator,
the SDI MCU control interface cable (10-pin) and the SDI trace interface cable (20-pin).
z When using this product connecting to the M32100T-SDI-E, M32170T-SDI or M32100T2-SDI-E, do not change
the MCU operating voltage.
z For the precautions for the combination of the emulator, refer to the user’s manual of each emulator.
Cautions for Differences between MCUs and This Product:
z For debugging, as the M32192F8VWG (1MB internal Flash ROM) on the M32186T2-PTC is used, be careful about
the difference of the internal memory size.
zWhen the clock select switch is set to the “SOCKET” side, the oscillation occurs by itself, be careful about the
difference of the resistance and the capacitor.
z The capacitive load of the all lines of the MCU will increase depending on wirings and connectors. Use the part
whose timing is critical after checking it works properly.
Cautions to Be Taken for This Product:
z When connecting the YQPACK144SD, be sure to use the included YQ-GUIDE’s.
z We cannot accept any request for repair.
z For purchasing the NQPACK144SD, YQPACK144SD and HQPACK144SD contact the following:
Tokyo Eletech Corporation
z For inquiries about the product or the contents of this manual, contact your local distributor.
Renesas Tools Homepage
(6/6)
|