R10S, R10D, R10P & R10SA
O w n e r ’ s M a n u a l
Contents
Getting Started
Important Safety Instructions
Polarization Instructions
State of California Proposition 65 Warnings
Description of the Vacuum
Assembling the Vacuum
2
3
3
4
5
Operation
Reclining the Handle
On/Off Switch
Edge Cleaning
Automatic Carpet Height Adjustment
Bare Floor Cleaning
6
6
6
6
6
Maintenance and Care
Power Cord Care
7
7
8
Vacuuming Under Furniture
Replacing the Vacuum Bag
Removing/Reinstalling the Bottom Plate
Replacing the Agitator Belt
Lifetime Belt Protection
Brushroll Jam Indicator
Resetting the Circuit Breaker
Replacing the Squeegee
Annual Checkup
9
10
10
11
12
12
12
Problem Solving Guide
Troubleshooting
Visit Riccar Vacuums Online
How to Contact Your Authorized Retailer
Key Replacement Parts
13
13
13
13
13
For Best Performance
Warranty
14
1
IMPoRtAnt sAFetY InstRUCtIons
When using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
The manufacturer cannot accept responsibility for damage
caused when the appliance is not used according to the
instructions, or for uses other than those for which it
was intended.
IMPoRtAnt:
To reduce the risk of fire, electric shock or injury:
• Do not leave appliance when plugged in.
Unplug from outlet when not in use and
before servicing.
• Do not handle plug or appliance with
wet hands.
• Do not put any object into openings. Do
not use with any opening blocked; keep
free of dust, lint, hair and anything that may
reduce air flow.
• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
• Keep hair, loose clothing, fingers and all
parts of body away from openings and
moving parts.
• Use only as described in this manual.
• Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left
outdoors, or dropped into water, return
it to your Authorized Riccar Retailer
for service.
• Do not pick up anything that is burning or
smoking, such as cigarettes, matches or
hot ashes.
• Do not use without vacuum bag in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not pull or carry by cord, use cord as
a handle, close a door on the cord, or pull
cord around sharp edges or corners. Do
not run appliance over cord. Keep cord
away from heated surfaces.
• Do not use to pick up flammable or
combustible liquids such as gasoline or
use in areas where they may be present.
• Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
• Do not attempt to service the unit while
appliance is plugged in.
sAVe tHese InstRUCtIons.
2
PolARIzAtIon InstRUCtIons
Power Cord, 2-Wire Polarized Cord
To reduce the risk of electric shock, this product is equipped with a polarized alternating
current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified
electrician to replace the obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to
cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to
cause birth defects or other reproductive harm.
3
DesCRIPtIon oF tHe VACUUM
1
2
11
10
3
5
4
7
6
1
2
Ergonomic Handle
On/Off Power Switch
Bag Compartment
Vacuum Nozzle
Headlight
8
9
3
4
5
6
Furniture Guard
7
Brushroll Jam Indicator (models R10P and R10SAND only)
8
Circuit Breaker Reset Button (models R10S and R10D only)
Handle Release Pedal
9
10
11
Quick Release Cord Hook
Upper Cord Hook
4
AsseMblIng tHe VACUUM
Attaching the Handle to the Vacuum
NOTE: Do not plug in the vacuum until it is
completely assembled.
The vacuum cleaner and the handle are
packed separately and require assembly.
• Thread the cord through the lower and upper
cord guides on the back of the vacuum bag (Fig. 1).
Fig. 2
Fig. 1
• Remove the handle bracket by removing the
two screws (Fig. 2).
• Place handle onto the back of the vacuum,
aligning holes with pegs (Fig. 3).
• Place the handle bracket back into position (Fig. 4).
• Secure with two screws removed in Step 2.
• Open the bag compartment to ensure a
vacuum bag is in place.
Fig. 3
Fig. 4
• Your vacuum is now ready for use.
• If storing the vacuum, wrap the cord clockwise
around the top and bottom cord hooks. Fasten
the plug to the wrapped cord using the channel
on the plug.
Unwinding the Power Cord
• The lower cord hook rotates to allow for
quick access to the power cord. Turn the
lower cord hook upward and you can quickly
drop the power cord to the floor without
unwinding it from the cord hooks.
• When storing the vacuum cleaner, turn the lower
cord hook to the downward position and wind the
power cord around the cord storage hooks.
5
oPeRAtIon
This vacuum is intended for household use only.
Reclining the Handle
• Press the handle release pedal located on the
back of the vacuum with your foot to recline the
handle (Fig. 1).
On/Off Switch
Fig. 1
• The power switch located on the vacuum handle, is a
three-way switch (Fig. 2). The middle position is the
“Off” setting, the rear position is the “On” setting and
the forward position is for “Maximum Power” (Fig. 3).
• Use the “Maximum Power” setting for carpet cleaning.
Use the “On” setting for cleaning bare floors and throw
rugs. Always turn the vacuum cleaner to the “Off”
setting before unplugging it from the electrical outlet.
Fig. 2
Edge Cleaning
The edge cleaning feature provides improved cleaning
near walls and stationary furniture. For maximum edge
cleaning, place the left side of the nozzle, from the user’s
perspective, against the wall or stationary furniture.
ON
OFF
MAX
POWER
Automatic Carpet Height Adjustment
Fig. 3
Your vacuum is designed with an automatic self-
adjusting nozzle. No manual adjustments are required.
The height of the nozzle automatically adjusts to the
flooring surface. This self-adjusting feature allows the
nozzle to float evenly over all flooring surfaces.
Bare Floor Cleaning
Your vacuum is equipped with a squeegee on the bottom
of the vacuum to improve its effectiveness in cleaning
bare floors (Fig. 4). When cleaning tile, hardwood, vinyl,
etc., use the “On” setting for best results.
Fig. 4
6
MAIntenAnCe AnD CARe
Power Cord Care
• If the cord or plug has any apparent damage,
refrain from using the vacuum. Please visit an
Authorized Riccar Retailer for a new cord
or plug.
• When the vacuum is in use, hold the cord to
keep from running over it.
• Avoid obstructions and do not pull the cord
around sharp edges or corners.
• Always keep the cord away from heated
surfaces and never close doors on it as this
may cause damage to the wiring.
• To unplug, always grasp the plug, not the cord.
Vacuuming Under Furniture
Your vacuum will lay flat on the floor for effective
cleaning under beds and tables.
• Press the handle release pedal once for normal
vacuum cleaning (Fig. 1).
• Continue to lower the handle to enable the
vacuum to lay flat on the floor (Fig. 2).
Fig. 1
Fig. 2
7
MAIntenAnCe AnD CARe
Replacing the Vacuum Bag
NOTE: Unplug the vacuum cleaner from the
electrical outlet before changing the bag.
• Unzip the bag compartment.
• Remove the used vacuum bag by pulling
the green bag collar tab away from the
vacuum (Fig. 1). Slide the used bag out
of the bag holder which automatically
seals the bag opening (Fig. 2). Discard
the used bag.
Fig. 1
• To install a new bag, slide the bottom of
the green bag collar into the bag holder
until it “snaps” into place (Fig. 3).
• Push the top of the bag collar upward
until the collar “snaps” into place on
the vacuum (Fig. 4).
Fig. 2
Fig. 3
Fig. 4
• Tuck the bag corners into the bag
compartment then zip the bag
compartment closed.
8
MAIntenAnCe AnD CARe
Removing and Reinstalling the
Bottom Plate
WARNING! To Reduce the Risk of Electrical
Shock or Injury From Moving Parts, Unplug
Before Servicing or Cleaning.
To Remove the Bottom Plate:
• Press the handle release pedal to place the
vacuum cleaner in the flat position.
• Turn the vacuum cleaner over, exposing the
bottom plate.
• Turn the two screws a quarter turn to release the
bottom plate (Fig. 1). Remove the bottom plate.
Fig. 1
• Reinstall the bottom plate by aligning the front
edge of the bottom plate into the notches inside
the nozzle housing (Fig. 2).
• Press the bottom plate into position until the
plate “clicks” on both sides. Tighten the two
screws a quarter turn to secure the bottom plate.
Fig. 2
9
MAIntenAnCe AnD CARe
Replacing the Agitator Belt
(Models R10S and R10D only)
WARNING! To Reduce the Risk of Electrical
Shock or Injury From Moving Parts, Unplug
Before Servicing or Cleaning.
NOTE: To ensure maximum cleaning
efficiency, the belt should be checked
regularly to be sure it is in good condition.
Check to see if the belt is stretched,
cracked, or if excessive slipping is
occurring. Replace if needed.
• Remove the bottom plate (see page 9).
• Remove the brushroll and the worn or
broken belt from the brushroll pulley and
the motor drive shaft (Fig. 1).
Fig. 1
• Loop the new belt around the motor
drive shaft and the brushroll (Fig. 2).
• Reinstall the brushroll into the housing.
Turn the brushroll by hand, making sure
the belt is not twisted and all rotating
parts move smoothly.
• Reinstall the bottom plate (see page 9).
Fig. 2
Lifetime Belt Protection Warranty
(Models R10P and R10SAND only)
Your vacuum belt is covered with a lifetime
warranty. Should the vacuum belt break,
simply bring your vacuum to your Authorized
Riccar Retailer for a free replacement.
10
MAIntenAnCe AnD CARe
Brushroll Jam Indicator
(Models R10P and R10SAND only)
If an object, such as a throw rug or article of
clothing is ever picked up into your vacuum,
the vacuum will sense this “jammed brushroll”
condition and turn off the brushroll. When this
happens, the Brushroll Jam Indicator light on the
top of the nozzle will flash in red.
• Turn off the vacuum and remove the cause of
the jam. Turn the vacuum back on.
• If the brushroll is free of obstructions and the
Brushroll Jam Indicator light is still flashing,
it’s likely the clogged condition is located in
the vacuum motor fan. If so, please take your
SupraLite to an Authorized Riccar Retailer for
service.
11
MAIntenAnCe AnD CARe
Resetting the Circuit Breaker
(Models R10S and R10D only)
WARNING! To Reduce the Risk of Electrical
Shock or Injury From Moving Parts, Unplug
Before Servicing or Cleaning.
Your vacuum features a circuit breaker to
protect the machine against damage due to
a surge in the electrical current. Electrical
surging can be a result of, though not limited
to, a jammed motor fan.
Circuit Breaker
Reset Button
Should your vacuum cleaner experience
a jammed brushroll with the circuit breaker
tripping, first turn the vacuum off and unplug
the unit. Inspect the brushroll by removing the
bottom plate (see page 9) and remove any
debris that may be causing the jam. Reinstall the
bottom plate (see page 9) and reset the circuit
breaker by pressing the Circuit Breaker Reset
Button. Plug in the power cord and turn on the
vacuum. If the vacuum fails to turn on, visit an
Authorized Riccar Retailer for assistance.
Replacing the Squeegee
If your squeegee splits or begins to look worn,
simply slide the worn squeegee from its track
and slide a new one into the track. If you have
trouble installing the new squeegee, please
visit an Authorized Riccar Retailer for help.
Annual Checkup
To keep your vacuum in peak operating
condition, it is recommended you bring
it to an Authorized Riccar Retailer for an
annual checkup. The Retailer will conduct a
comprehensive examination to ensure your
vacuum is in top operating condition.
12
PRobleM solVIng gUIDe
Troubleshooting
WARNING! To Reduce the Risk of Electrical Shock or Injury From Moving Parts, Unplug
Before Servicing or Cleaning.
CAUTION! To Reduce the Risk of Electric Shock, Do Not Handle Plug or Appliance with Wet Hands.
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
Vacuum won’t turn on
• Power cord not firmly
plugged in
• Plug cord in firmly
• Blown fuse or tripped
breaker
• Check house fuse or
breaker. Replace fuse/
reset breaker.
• Needs service
• Take to Authorized
Riccar Retailer
Vacuum won’t pick up or
low suction
• Vacuum bag full
• Broken belt
• Worn brushroll
• Install new bag
• Replace belt
• Replace brushroll
Dust escaping from
vacuum
• Vacuum bag not installed
properly
• Install bag properly.
Review bag installation
(page 8).
Any other service should be performed by an Authorized Riccar Retailer.
To locate your nearest Authorized Riccar Retailer visit our website
Key Replacement Parts
• Genuine HEPA Media Vacuum Bags: RLH-6
• Genuine Vacuum Belts: R10B-2
For Best Performance
• Keep your vacuum clean and in good operating condition.
• Change the vacuum bag once a month or when the bag is 2/3 full to maximize cleaning performance.
• Always use genuine vacuum bags and replacement parts. Use of other products may result in poor
cleaning performance, potential vacuum cleaner damage and may void vacuum warranty. Genuine
products are designed for maximum cleaning performance.
• Have your vacuum checked annually by your Authorized Riccar Retailer.
• Store your vacuum carefully in a dry area.
• For optimum cleaning performance and safety, follow your owner’s manual instructions.
13
WARRAntY
What is Covered:
This warranty covers any defects in material and workmanship in your new Riccar vacuum
and applies exclusively to the original purchaser.
How Long Coverage Lasts:
Warranty coverage for R10S and R10D lasts four years. R10P and R10SAND lasts 5 years.
Household models used commercially are only warranted for 90 days.
What is Not Covered:
• Damage to the vacuum which occurs from neglect, abuse, alterations, accident,
misuse or improper maintenance.
• Normal replacement items: disposable bags, belts (models R10S and R10D only)
and light bulbs.
What We Will Do:
This warranty provides, at no cost to you, all labor and parts to keep this vacuum in
correct operating condition during the warranted period.
How to Get Service:
Warranty service can only be obtained by presenting the vacuum to an Authorized
Riccar Retailer. A proof-of-purchase and product serial number will be required before
service is rendered. To locate your nearest service center, please call 1-888-6-RICCAR
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES
WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED, (INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE). THIS WARRANTY
DISCLAIMS LIABILITY FOR INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
How State Law Applies:
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Register your warranty online at www.Riccar.com
14
oWneR’s WARRAntY InFoRMAtIon
keep this for your records…
Date of purchase
Serial number
Model number
Purchased from:
Store name
Address
City, State, Zip
Telephone
15
notes
|