Roadmaster Car Speaker VRS693 User Guide

Frequently Asked Questions  
1. Location of Speakers  
1 Pair VRS693  
6" X 9" 3-Way Speakers  
What if there is no sound?  
The placement of the speakers will vary from vehicle to vehicle. Most vehicles have factory  
cut-outs on the rear window deck behind the rear seat, in the front doors, or front kick  
panels. Before permanently installing the VRS693 speakers in your car, connect the wires to  
the speakers according to your audio system’s installation manual, in the approximate  
location you will install them. If you are satisfied with the location proceed with the  
permanent installation.  
Your stereo may have a blown fuse. Replace fuse with the same amperage and style.  
You may have improper wiring. Refer to the wiring guide that came with your stereo/amplifier. Check  
all wires for a secure connection.  
What if the sound volume is low?  
Your stereo may not have enough power. You may have to install an amplifier to drive the speakers.  
Read First!  
Why do I have a whining noise coming from the speakers?  
You may have poor filtering of your alternator. If that is the case, then you may need to add an  
alternator filter to the power lead.  
Dear Customer,  
CONGRATULATIONS.  
The VRS693 6x 9" 3-way speakers, when used as described, will give you years of depend-  
able service in your car, truck, RV, or mini-van. We have taken numerous measures in quality  
control to ensure that your product arrives in top condition, and will perform to your satisfac-  
tion. In the rare event that your VRS693 6x 9" 3-way speakers contains a damaged or miss-  
ing item, does not perform as specified, requires warranty service, or you have an installation  
problem, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR TOLL-  
FREE NUMBER FROM THE U.S.A. AND CANADA 1-800-445-1797 and ask to speak with a  
member of our technical service team, or submit your questions by e-mail to  
[email protected] and a member of our technical service team will respond by e-mail  
to your questions. Our in-house technical service team will expedite delivery of your part,  
advise you on installation, or help troubleshoot a problem with you. If your product needs  
warranty service, our technical service team representative will help you obtain the fastest  
remedy possible under the warranty.  
Why do I have odd sounding noises coming from the speakers?  
You may have corroded battery terminals and/or a weak battery. If the terminals on the battery are  
corroded, clean them; then check the sound. If the sound system is still making noises, then check  
battery strength. If it is low, then recharge or replace the battery.  
Why does the speaker have sound coming from one channel only?  
First make sure the balance control is set correctly. If the balance is set correctly, your stereo may be  
defective or the speaker may be defective. To troubleshoot this problem you MUST change both  
positive and negative leads of each channel with the positive and negative leads of the opposite  
channel. If the same speaker has no sound, then the speaker is no good. If the opposite speaker has  
no sound, then your stereo may be defective.  
2. Mounting The Speakers  
You should only mount your speakers in factory precut holes. We DO NOT  
recommend that you cut holes for mounting the speakers. If there are no  
factory precut holes, consider having the speakers professionally installed.  
Specifications  
Give Us A Call, We'll Help You Install  
• 6” x 9" diecast aluminum basket .  
• Black glass fiber wooven cone  
• Buytl Rubber Surround  
Hi performance 51mm PEI Midrange + 25 PEI Nd Tweeter  
In a Precut Hole  
• Freqency Response : 40 - 20K Hz  
• Sensitivity: 90dB/2.83V/1M (+/-3dB)  
• Rms: 100 Watts Per Pair  
• Max Pwr: 500 Watts Per Pair  
• Impedance: 4Ω  
1. Connect speaker wires.  
INTERIOR PANEL  
PLEASE DO NOT RETURN PRODUCT TO STORE.  
• 1.2" ASV 4 layers  
• 24.6 Oz magnet  
• Front Facing Cable-Free Tweeter  
For Help Go To  
GRILL  
2. Slip the spring nut(s) (provided)  
into place and align the holes.  
WWW.VR-3.COM  
For Information and Technical Assistance,  
Call Toll-Free in U.S.A., Puerto Rico, and Canada.  
SPRING NUT  
Parts  
The small hole of  
the spring nut is on  
this side of panel  
1-800-445-1797  
3. Place the speaker grill on the  
speaker, then put the supplied  
screws through the screw  
holes of the speaker grill and  
speaker. Align the screws with  
screw holes of the spring nuts.  
Notes  
4. Tighten the screws, but not so  
tight as to crack the plastic of  
the speaker grills.  
SPEAKER  
WIRE  
8 - Spring Nuts  
SCREW  
In an Enclosure  
8 - Screws  
1. Place the speaker in the hole.  
2 - Speaker Grills  
2 - 6" X 9" Speakers  
2. Mark the speaker’s screw holes on the enclosure,  
then remove the speaker from the hole.  
3. Drill pilot holes where you have marked the  
enclosure.  
Tools Needed to Install  
Limited Warranty  
VIRTUAL REALITY SOUND LABS® products are designed and manufactured to provide a high level of trouble-free performance.  
VIRTUAL REALITY SOUND LABS® warrants, to the original purchaser, that its products are free from defects in material and  
workmanship for 30 days from the date of original purchase, as part of our commitment to product excellence VIRTUAL REALITY  
SOUND LABS® and/or it’s affiliates routinely improves the designs, materials or production methods of its existing products. Because  
it is impractical to publicize all changes in every product, we reserve the right to make such changes without notice.  
CONDITIONS OF WARRANTY:  
4. Connect the speaker wires.  
5. Align the speaker with the holes, then insert the  
screws and tighten.  
• Marker  
• Nail Set/Center Punch  
• Phillips Screwdriver  
• Wire Cutter  
All auto audio components must be securely mounted. Driving styles  
and road conditions such as sudden stops, sharp curves, and bumpy  
roads may cause unsecured items to move about the vehicle, causing  
physical injuries to vehicle occupants and/or vehicle damage.  
If during the 30 day warranty period your new product is found to be defective, VIRTUAL REALITY SOUND LABS® will repair such  
defect, or replace the product, without charge for parts or labor subject to the following conditions:  
1. All repairs must be performed by VIRTUAL REALITY SOUND LABS® and/or it’s affiliates in Eatontown, New Jersey.  
2. The equipment must not have been altered or been damaged through negligence, accident, or improper operation.  
3. The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.  
4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.  
• Electric Drill  
with 1/16" bit  
• Safety Glasses  
• Hammer  
• Electrical Tape  
5. Repair or replacement parts supplied by VIRTUAL REALITY SOUND LABS® under this warranty are protected only for the  
unexpired portion of the original warranty.  
Before You Install  
6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; correction of antenna  
problems; costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, accessories or car electrical  
systems.  
3. Connecting The Wires  
Automotive audio equipment installations can be troublesome at times, even to the most  
experienced of installation technicians. If you are not confident working with electrical wiring,  
removing and reinstalling interior panels, carpeting, dashboards or other components of your  
vehicle, please call our toll-free help line 1-800-445-1797 and our in-house technical service  
team will answer your installation questions.  
7. VIRTUAL REALITY SOUND LABS® will not be responsible for any charge incurred for installation.  
OWNER'S RESPONSIBILITIES:  
To Strip Insulation from Wire:  
To Attach Wires to Terminals:  
VIRTUAL REALITY SOUND LABS® will make every effort to provide warranty service within a reasonable period of time.  
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING  
SERVICE, PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.  
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:  
1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.  
2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping carton, and  
freight and insurance prepaid to the following address: VIRTUAL REALITY SOUND LABS, Service Department, 41 James Way,  
Eatontown, New Jersey 07724.  
Speaker Terminals  
Strip a fingertip’s width  
of insulation from end  
of speaker cable. Twist  
strands of wire together.  
1. Push the speaker terminal  
down as shown.  
Before permanently installing the VRS693 speakers in your car, connect the wires to the  
speakers according to your audio system’s installation manual, in the approximate location you  
will install them. If you are satisfied with the location, proceed with the permanent installation.  
2. Insert  
a
speaker  
wire with about .25”  
of insulation removed  
from the end, then  
release the terminal.  
3. Please include a detailed explanation of the problem you are having.  
4. If your product is found by VIRTUAL REALITY SOUND LABS® to have a defect in material or workmanship, within the warranty  
period, it will be repaired or replaced at no charge and returned to you prepaid. Where permitted by Iaw VIRTUAL REALITY SOUND  
LABS® liability shall be limited to that set forth in this warranty. This warranty shall be the exclusive remedy of the purchaser.  
VIRTUAL REALITY SOUND LABS® makes no other warranty of any kind, expressed or implied; and all implied warranties, are  
hereby disclaimed by VIRTUAL REALITY SOUND LABS® and excluded from this warranty, VIRTUAL REALITY SOUND LABS®  
and/or it’s affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or  
consequential, arising out of the use or intended use of the product.  
Before you install the VRS693 speakers you must make sure  
you have enough depth/space behind the mounting surface.  
You do not want the back of the speaker magnet to touch any  
part of your vehicle, or interfere with the operation or function  
of any component in your vehicle. (ie. windows or trunk lid)  
Speaker Wire  
When connecting the speaker wires to your speakers in a new installation, you should follow  
the wiring instructions from your audio system’s manufacturer. For most systems, maintain  
proper polarity by attaching the Positive Wire (+) to the Positive Terminal (+) and the Negative  
Wire (-) to the Negative Terminal (-).  
3.5" or 7.9 cm  
©2008 Intellectual Solutions Inc., All rights reserved. All designs, logos and images are the exclusive property of Intellectual  
Solutions Inc. and/or it’s affiliates. US and Foreign Intellectual Property Rights Pending 071408 Printed in China 00000  
 

Quantum Boiler GAS FIRED BOILERS User Guide
Quasar VCR VHQ730 User Guide
Radio Shack Metal Detector 63 3013 User Guide
RayTek Thermometer Food Safety Thermometers User Guide
RCA VCR VR651HF User Guide
Remington Electric Shaver MB 400 User Guide
Rover Lawn Mower 35M92 User Guide
Samsung Microwave Oven DE68 03267F 01 User Guide
Samsung MP3 Player YP NEU User Guide
Senco Air Compressor PC201 User Guide