ELECTRIC AND GAS
DRYERS
Use & Care Guide
For questions about features, operation/performance
parts, accessories or service, call: 1-800-447-6737.
or visit our website at www.roperappliances.com
Table of Contents................................................. 2
3405639A
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
•
•
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic
precautions, including the following:
I
I
Read all instructions before using the dryer.
I
Do not repair or replace any part of the dryer or
attempt any servicing unless specifically recom-
mended in this Use and Care Guide or in published
user-repair instructions that you understand and have
the skills to carry out.
Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
I
I
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
I
Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
I
I
Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children.
I
I
Clean lint screen before or after each load.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
Before the dryer is removed from service or dis-
carded, remove the door to the drying compart-
ment.
Do not reach into the dryer if the drum is moving.
Do not install or store the dryer where it will be
exposed to the weather.
I
I
I
I
See installation instructions for grounding require-
ments.
I
Do not tamper with controls.
SAVE THESE INSTRUCTIONS
4
PARTS AND FEATURES
1
4
5
2
3
6
1. Control panel
Large side-swing door
Super wide-swing door
Additional features your dryer may have
End of Cycle Signal selector
Drum light
2. Model and serial number label
3. Dryer drum
4. Lint screen
Small side-swing door
5. Exhaust grille
6. Wide-opening door
Optional purchase
Drying rack
Control Panel
NOTE: The drawings in this book may vary from your dryer. They are designed to show all of the models covered by this book.
Your dryer may not include all features.
5
3. The exhaust vent can be routed up, down, left, right, or
straight out the back of the dryer. Space requirements are
listed in your Installation Instructions.
CHECKING
YOUR VENT
Your dryer must be properly installed and vented to achieve
maximum drying efficiency and shorten drying times. Use the
minimum recommended installation clearances (found in your
Installation Instructions) to avoid blocking the flow of combustion
and ventilation air. Refer to your Installation Instructions for more
information.
4. Use the straightest path possible when routing the exhaust
vent. Use the fewest number of elbows and turns. Allow room
when using elbows or making turns. Bend vent gradually to
avoid kinking.
Fire Hazard
Use a heavy metal vent.
5. Use clamps to seal all joints. Do not use duct tape, screws or
other fastening devices that extend into the interior of the
vent to secure vent.
Do not use a plastic vent.
Do not use a metal foil vent.
6. Clean exhaust vent periodically, depending on use, but at
least every 2 years, or when installing your dryer in a new
location.
Failure to follow these instructions can result in
death or fire.
I
Disconnect vent from the dryer and clean one section at a
time until you reach the exhaust hood.
If the dryer is not properly installed and vented, it will not be
covered under the warranty.
NOTE: Service calls caused by improper venting will be paid for
by the customer, whether it was a paid installation or self-
installed.
1. Do not use plastic vent or metal foil vent. Use 4 in. (10.2 cm)
metal or flexible metal vent. Do not kink or crush flexible
metal vent. It must be completely extended to allow adequate
exhaust air to flow. Check vent after installation. Refer to your
Installation Instructions for proper length requirements of
vent.
I
To clean out lint, use the hose attachment on your
vacuum, or a pole or wire with a feather duster or rag
attached.
I
I
Be sure the flapper on the outside end of vent moves
freely.
When cleaning is complete, be sure to follow the
Installation Instructions supplied with your dryer for final
product check.
4"
(10.2 cm)
2. Use a 4 in. (10.2 cm) exhaust hood. Smaller hoods increase
drying times.
2
1
4"
(10.2 cm)
4"
(10.2 cm)
6
to dry most heavyweight and medium weight loads. See
“Drying, Cycle, and Temperature Tips.”
DRYER USE
Starting Your Dryer
3. Select a temperature setting on models with a Temp/Fabric
selector. The cycle descriptions include temperature setting
suggestions.
NOTE: The temperature selector is part of the Cycle Contol
knob on some models.
4. Select the End of Cycle Signal, if available. The signal is
helpful when drying permanent press or synthetics. Promptly
remove these items from the dryer at the end of the cycle to
prevent wrinkles.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
On some models you may have:
Do not dry anything that has ever had anything
flammable on it (even after washing).
I
I
I
An automatic End of Cycle Signal that will sound when
cycle is completed.
An End of Cycle Signal that can be adjusted. Turn the
selector to the desired volume.
Failure to follow these instructions can result in
death, explosion, or fire.
An End of Cycle Signal that is part of the START button.
Turn the START button to ON or OFF.
5. Select the desired option. See “Additional Features.”
6. Push the START button.
Stopping and Restarting
You can stop your dryer any time during a cycle.
To stop your dryer
Open the dryer door or turn the Cycle Control knob to OFF.
NOTE: The Cycle Control knob should point to an Off area when
the dryer is not in use.
Fire Hazard
To restart your dryer
1. Close the door.
No washer can completely remove oil.
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
2. Select a new cycle and temperature (if desired).
3. Push START.
Items containing foam, rubber, or plastic must be
dried on a clothesline or by using an Air Cycle.
Loading
Load clothes loosely into the dryer. Do not pack the dryer. Allow
space for clothes to tumble freely. The following chart shows
examples of balanced loads that would allow for proper tumbling.
Failure to follow these instructions can result in
death or fire.
Heavy work
clothes
3 pair of pants, 4 pair of jeans,
2 pair of overalls, 3 shirts
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
1. Load clothes loosely into the dryer and close the door. Do not
Delicates
3 camisoles, 1 robe, 4 slips,
6 undergarments, 2 sets of sleepwear,
1 child’s outfit
pack the dryer. Allow space for clothes to tumble freely.
Towels
10 bath towels, 10 hand towels,
14 washcloths, 1 bath mat
Mixed Load
3 double sheets, 4 pillowcases,
8 T-shirts, 6 pair of shorts, 2 blouses,
8 handkerchiefs
2. Turn the Cycle Control knob to the recommended cycle for
the type of load being dried. Use the Energy Preferred setting
7
reached. The Cycle Control knob does not move until the load is
almost dry. After the cool down, the knob automatically turns to
an Off area and tumbling stops.
Drying, Cycle and Temperature Tips
Select the correct cycle and temperature for your load.
Dry most loads using the Energy Preferred Automatic Setting ( ).
*
Cool Down tumbles the load without heat during the last few
minutes of all cycles to make the load easier to handle.
I
If the load is drier than you like, select a setting closer to
Less Dry the next time you dry a similar load.
Drying tips
I
If the load is not as dry as you like, complete drying using the
Timed Dry cycle. The next time you dry a similar load, select a
setting closer to Very Dry.
I
Follow care label directions when they are available.
I
If you use fabric softener sheets, use only those labeled
“dryer safe.” Follow package instructions.
NOTE: Drying time with an automatic cycle varies according to
the type of fabric, size of load, and temperature setting. See
“Drying, Cycle and Temperature Tips.”
I
Remove the load from the dryer as soon as tumbling stops, to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
Cycle and temperature tips
Timed Dry Cycle
I
I
I
Dry most loads using the Energy Preferred setting, if available
on your dryer.
Use the Timed Dry cycle to complete drying if items are still
damp after the automatic cycle.
Use a High heat setting for drying heavyweight items such as
towels and work clothes.
Timed Dry is also useful for:
I
Heavyweight and bulky items, such as bedspreads and work
clothes and large loads that require a long drying time. Set
the Temperature selector to High heat or to a setting that
matches the care label directions.
Use a Medium heat setting for drying medium weight items,
such as sheets, underwear, permanent press fabrics, and
some knits.
I
Lightweight items, such as lingerie, blouses, and knits that
require a short drying time. Set the Temperature selector at
Low heat.
I
I
I
Use a Low heat setting for drying lightweight items such as
lingerie, blouses, dresses, and some knits.
Use a no-heat (air) setting for rubber, plastic, or heat-sensitive
fabrics.
NOTE: Drying time and temperature will depend on your dryer
model.
Line dry bonded or laminated fabrics.
Max Dry
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions. If you are unsure
of the temperature to select for a load, select a lower setting
rather than a higher setting.
Select this setting to evenly dry large or heavy items, such as
thick cotton bath towels or robes. Set the Temperature selector, if
available, to High heat.
Damp Dry
Select this setting to dry items to a damp level or dry items that
do not require an entire drying cycle. Damp dry items such as
jeans (to prevent stiffness) or cotton clothes (to make pressing
easier). Set the Temperature selector, if available, based on the
fabrics in your load.
CYCLES
This manual covers several different models. Your dryer may vary
from the model shown and may not have all of the cycles and
features described.
Wrinkle Free
Use this setting to remove wrinkles from items, such as clothes
packed in a suitcase or items wrinkled from being left in the dryer
too long. Set the Temperature selector, if available, at Low or
Medium heat, depending on the fabrics in your load.
Cycle Control knob
No Heat/Fluff Cycle
Use the No Heat/Fluff cycle for items that require drying without
heat, such as rubber, plastic and heat-sensitive fabrics. See the
chart for examples of items that can be dried using the No Heat/
Fluff cycle.
Type of Load
No Heat/Fluff
cycle*
Foam rubber - pillows, padded bras,
stuffed toys
20 - 30
20 - 30
40 - 50
10 - 20
Plastic - shower curtains, tablecloths
Rubber-backed rugs
Automatic Cycle
Olefin, polypropylene, sheer nylon
Use the automatic cycle to dry most loads. Your dryer uses the
AUTO SENSE DRY automatic control that senses the moisture in
the load and shuts off the dryer when the selected dryness is
*(Minutes). Reset cycle to complete drying, if needed.
8
When using No Heat/Fluff
This chart shows examples of items that can be rack-dried and
the suggested cycle, temperature setting, and drying time. Actual
drying time will depend on the amount of moisture items hold.
I
I
I
Check to see that coverings are securely stitched.
Shake and fluff pillows by hand periodically during cycle.
Dry item completely. Foam rubber pillows are slow to dry.
Rack Dry
Cycle
Temp
Time*
Wool Sweaters
Block to shape and lay flat on
the rack
Timed
Dry
Low
60
Additional Features
WRINKLE PREVENT™ feature
Stuffed toys or pillows
Timed
Dry
Low
60
90
90
When you are unable to remove a load of clothes from the dryer
as soon as it stops, wrinkles can form. The WRINKLE
PREVENT™ feature periodically tumbles, rearranges and fluffs
the load without heat for up to 45 minutes. During this cycle, the
dryer stops tumbling and then begins to tumble again. This stop
and start process is repeated until the end of the cycle. A signal
will sound periodically when the WRINKLE PREVENT™ feature is
on, if the End of Cycle Signal is selected. The signal and the
tumbling will end when you open the dryer door, or turn the Cycle
Control knob to Off.
Cotton or polyester fiber filled
Stuffed toys or pillows
Foam rubber filled
Air
None
None
(no heat)
Sneakers or canvas shoes
Air
(no heat)
*(Minutes). Reset cycle to complete drying, if needed.
I
On some models, the WRINKLE PREVENT™ feature is
automatic and activates at the end of the cycle if you do not
open the dryer door within a few minutes after the cycle ends.
DRYER CARE
I
On some models, you can turn the WRINKLE PREVENT™
feature On or Off.
End of Cycle Signal
Cleaning the Lint Screen
If the End of Cycle Signal is On, the signal sounds when a cycle is
complete. If the WRINKLE PREVENT™ feature is on, the signal
sounds every few minutes. The signal stops when you open the door.
Every load cleaning
The lint screen is located on the top of the dryer. Clean it before
each load. A screen blocked by lint can increase drying time.
To clean
1. Pull the lint screen towards you. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint. Wet
lint is hard to remove.
Drying Rack
The drying rack is useful for machine drying items you would not
necessarily want to tumble dry or that you would normally line dry
(for example, sweaters or pillows).
2. Push the lint screen firmly back into place.
IMPORTANT:
If your model does not have a drying rack, you may purchase
one. For ordering information, please refer to the “Assistance or
Service” page of this manual. You may also contact the dealer
from whom you purchased your dryer.
I
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
To use the drying rack
I
Some towels made of synthetic fibers and natural fibers
(polyester and cotton blends) may shed more lint than other
towels, causing your dryer’s lint screen to fill up faster. Be
sure to remove lint from the lint screen before and after drying
new towels.
1. Slide rear pegs into the dimples on the back wall of the dryer.
Lower the front legs to rest on the dryer opening.
I
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint. See “Checking Your
Vent.”
As needed cleaning
2. Put the wet items on top of the rack. Leave space between
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
the items so air can reach all the surfaces. Close the door.
NOTE: Do not allow items to hang over the edge of the rack.
3. Select a timed drying cycle and temperature, or an air cycle.
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using an air cycle.
Clean the lint screen with a nylon brush every six months or more
frequently if it becomes clogged due to a residue buildup.
4. Push the START button.
NOTE: The rack must be removed for normal tumbling. Do not
use the automatic cycle with the drying rack.
9
To wash
1. Roll lint off screen with your fingers.
2. Wet both sides of lint screen with hot water.
Changing the Drum Light
The dryer light automatically turns on inside the dryer drum when
you open the door.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
To change the drum light
1. Unplug dryer or disconnect power.
2. Open the dryer door. Locate the light bulb cover on the back
wall of the dryer. Remove the screw located in the lower right
corner of the cover. Remove the cover.
3. Turn bulb counterclockwise. Replace the bulb only with a 10-
watt appliance bulb. Replace the cover and secure with the
screw.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Insert lint
screen back into dryer.
4. Plug in dryer or reconnect power.
Cleaning the Dryer Interior
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid
the cost of a service call...
Clothes are not drying satisfactorily
I
Check the following:
Is the lint screen clogged with lint?
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes.
Hold your hand under the outside exhaust hood to check air
movement. If you do not feel air movement, clean exhaust
system of lint or replace exhaust vent with heavy metal or
flexible metal vent. See your Installation Instructions.
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion,
or fire.
Is the exhaust vent crushed or kinked? Replace with heavy
metal or flexible metal vent. See your Installation Instructions.
To clean dryer drum
1. Make a paste with powdered laundry detergent and very
Has a fuse blown, or a circuit breaker tripped? Electric dryers
use 2 household fuses or breakers. The drum may be turning,
but you may not have heat.
warm water.
2. Apply paste to a soft cloth.
OR
Has an air dry cycle been selected? Select the right cycle for
the types of garments being dried. See “Drying, Cycle and
Temperature Tips.”
Apply a liquid, non-flammable household cleaner to the
stained area and rub with a soft cloth until all excess dye is
removed.
For gas dryers, is the valve open on the supply line?
3. Wipe drum thoroughly with a damp cloth.
Are fabric softener sheets blocking the grille? Use only one
fabric softener sheet, and use it only once.
4. Tumble a load of clean cloths or towels to dry drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and will
not stain future loads of clothes. Dry unstable dye items inside-
out to prevent dye transfer.
I
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
I
I
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water
and with items that hold moisture (cottons).
Removing Accumulated Lint
From Inside the Dryer Cabinet
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
Dryer will not run
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
I
Check the following:
Is the power cord plugged in?
Has a fuse blown, or has a circuit breaker tripped?
Was a regular fuse used? Use a time-delay fuse.
Is the dryer door firmly closed?
Was the START button firmly pressed?
Is a cycle selected?
10
I
If the dryer is electric, is it being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
Unusual sounds
I
I
Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
Garment damage
Is it a gas dryer?
The gas valve clicking is a normal operating sound.
I
Check the following:
Were zippers, snaps, and hooks left open?
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
Lint on load
I
I
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Is the load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
ASSISTANCE OR SERVICE
I
I
Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
Was the load overdried?
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Use correct dryer settings for load type. Overdrying can
cause lint-attracting static electricity. See “Drying, Cycle, and
Temperature Tips.”
I
I
Was paper or tissue left in pockets?
If you need replacement parts
Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and
laundering.
If you need to order replacement parts, we recommend that you
only use FSP® replacement parts. These parts will fit right and
work right, because they are made with the same precision used
to build every new ROPER® appliance. To locate FSP
replacement parts in your area, call our Customer Interaction
Center or your nearest Whirlpool designated service center.
Stains on load or color change
I
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially-dried load can
stain your garments.
For assistance
Call the Customer Interaction Center toll free at
1-800-44-ROPER (1-800-447-6737).
Our consultants provide assistance with:
I
I
Were items soiled when placed in the dryer?
I
I
I
I
I
Features and specifications on our full line of appliances
Items should be clean before being dried.
Installation information
Were items properly sorted?
Sort light colors from dark colors. Sort colorfast items from
noncolorfast items.
Use and maintenance procedures
Accessory and repair parts sales
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
Items shrinking
I
I
Was the dryer overloaded?
I
Referrals to local dealers, repair parts distributors, and
service companies.
Dry smaller loads that will tumble freely.
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Whirlpool designated service technicians are trained to fulfill the
product warranty and provide after-warranty service, anywhere in
the United States.
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
Loads are wrinkled
I
I
Was the load removed from dryer at the end of the cycle?
For further assistance
If you need further assistance, you can write with any questions
or concerns at:
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Roper Brand Home Appliances
Customer Interaction Center
553 Benson Road
I
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Odors
I
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, re-wash and dry the clothing.
11
ROPER® DRYER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4 in. (10.2 cm) metal exhaust vent must be used. Refer
to the venting section of this manual and your Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Outside the 50 United States, this warranty does not apply. Contact your authorized Roper dealer to determine if another
warranty applies.
If you need service, first see the “Troubleshooting” section of this book. Additional help can be found by checking the “Assistance or
Service” section or by calling the Customer Interaction Center toll free at 1-800-44-ROPER (1-800-447-6737) from anywhere in the
U.S.A. or write: Roper Brand Home Appliances, Customer Interaction Center, 553 Benson Road, Benton Harbor, MI 49022-2692. 1/02
Keep this book and your sales slip together for future
Dealer name____________________________________________________
reference. You must provide proof of purchase or installation
date for in-warranty service.
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Write down the following information about your dryer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label, located on your appliance as shown in “Parts and
Features.”
3405639A
© 2002 Whirlpool Corporation.
5/02
Printed in U.S.A.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
|