Power Protection UPS RU101/102
User Manual
The “Battery Backup & Turn of the UPS and reduce the amount
The UPS is
making a
Surge Protection”
of equipment connected to these
outlets.
continuous sound outlets are overload.
and the “Overload”
indicator is light.
RU-101/102
The UPS does not Due to age the battery Removed all connected equipments
provide expected does not hold a full from the UPS and charge the battery at
Rosewill Uninterruptible Power System (UPS) protects your computer hardware from physical
damage and will provide emergency battery backup power to prevent data loss in the event of
power problems.
runtime.
charge
least 8 hours.
Return for service or you can replace
the battery by ordering one new battery
Connected
The “Battery Backup & Refer to the Indicator Table “ UPS is
The main features include
equipments lose Surge Protection”
making a continuous sound and the
Overload indicator is light”
The UPS will turn off when the battery
power while
outlets are overload.
‹
‹
‹
Advanced equipment & data protection from blackouts, brownouts, sags, AC line noise and
surges.
connected to the
Power the UPS.
The UPS has
exhausted its available has been depleted during the failure of
Full analytical high performance micro-processor control with true RMS synchronous
calculation.
run time.
utility power. Allow UPS to re-charge
before continuing using of the UPS.
Connected equipment is Ensure the equipment that you want to
connected to the wrong stay powered during a failure of utility
outlet.
Intelligent battery management for battery status, battery power saving & battery
replacement control.
power is plugged into the “Battery
Backup & Surge Protection” outlets.
‹
‹
‹
DC direct start-up capability, complete diagnostic indication and control.
Built-in USB communication port for RU102.
The UPS may be faulty. Please Call your agency for further
troubleshooting.
Phone jack for phone and fax lines for RU102.
Indicators
Specification
600VA/300W
Model
RU-101
RU-102
Capacity
600VA/300W
1000VA/500W
120V +15%/- 20%
Input Voltage Range
Output Voltage Range
Frequency
120V +/-12%
50 / 60 Hz auto sensing
Outlets
6 Outlets (3 Battery Backup & Surge)
480 Joules
Lighting / Surge Protection
Transfer Time to Battery/AC
4 ms (typical)
Battery Type
Sealed and leak proof maintenance free lead-acid battery
Battery Specification
12V/5AH×1
W/O
12V/9AH x 1
RJ11/RJ45
Phone / Fax/ Network
Protection
Circuit breaker
Short Circuit Protection
Communication Port
Operation Temperature
Operation Relative Humidity
Storage Temperature
Net Weight
W/O
USB
+32℉ ~ 104℉ (0℃ ~ 40℃)
0 to 95% non-condensing
+5℉ ~ 113℉ (-15℃ ~ 45℃)
1000VA/500W
7.8 lbs
6.1×4.3×8.3
9.12 lbs
7.1x6x9.5
Dimensions (WxDxH) inch
Operation & Installation
Rosewill UPS can protect your equipment from all power problems such as surge, spikes,
blackouts, brownouts and line noise. When AC power is present and the ON/OFF switch is turned
on, Rosewill UPS continues to charge the battery and provide the power to the equipment directly
from the AC line. The battery can provide stable power to complete your work, save your data and
safely shut down your system when the utility power has failed.
Rosewill UPS is simple to operate and install. Following are the installation steps to connect he
equipment to the UPS.
1. Connect Rosewill UPS to grounded AC power Outlets.
2. Charge the battery at least 8 hours for a full charge before use.
3. Plug your computer and monitor into the “Battery Backup & Surge Protection” outlets. (These
outlets will provide emergency battery backup power during power problems as well as surge
protection from surge and spike.)
CAUTION: Do NOT plug LASER PRINTERS into any of the “Battery Backup” outlets.
CAUTION: Do NOT plug ACCESSORY SURGE STRIP into any of the “Battery Back & Surge
Protection” outlets.
4. Plug your peripheral equipment (printer, scanner, fax, speaker, etc.) into the “Surge
Protection” outlets. (These outlets will NOT provide battery backup power during a utility
power failure).
1. On/Off Switch
This On/Off switch controls power to your equipment and performs a self-test to detect inverter,
line, battery status & LEDs.
5. Switch on the Rosewill offline UPS product while the connected equipment is off,.
6. Turn on your connected equipment when the “AC mode” LED light is illuminated.
NOTE: Turn on the UPS.
Press and hold the switch for more than two seconds and release the switch after the beep.
The UPS will start and provide the stable power to your equipments.
Troubleshooting
NOTE: Turn off the UPS.
Symptom
Possible Cause
Action to Take
Press and hold the switch for more than two seconds and release the switch. The UPS will
shut down completely.
The UPS will not UPS is not turn on
turn on.
Switch on the On/Off switch. If the
power is not present, please make sure
your circuit breaker on the building is not
accidentally turned off.
NOTE: Perform Self-test.
The UPS will perform self-test for about 10 seconds when the UPS is turned on.
2. Line / Battery LED (Green LED)
Circuit Breaker has
tripped.
Reduce the amount of equipment
plugged into the “Battery Backup &
Surge Protection” outlets of the UPS.
Next, rest the circuit breaker by pushing
it back in.
Indicates the UPS is providing AC power to your equipment. When the LED is blinking the UPS is
providing power from the battery.
3. Warning LED (Red)
|