Notice Pressure iron & steamer 24/08/06 10:14 Page 3
IMPORTANT SAFETY INSTRUCTIONS
When using your appliance, basic safety reassembly can cause a risk of electric shock
precautions should always be followed, when the appliance is used.
including the following :
- Not intended for use by children. Close
Read all instructions before using the supervision is necessary for any appliance
generator.
being used near children. Unsupervised use
can result in fire or personal injury. Do not
- Use appliance only for its intended use.
- To protect against a risk of electric shock, do leave appliance unattended while plugged in,
not immerse the appliance in water or other on an ironing board, or while it is still hot.
- Burns can occur from touching hot metal parts,
hot water or steam. Use caution when you turn a
steam generator upside down.There may be hot
water in the reservoir.
-Never attempt to unscrew the boiler cap while
the appliance is in use.The strong steam pressure
could result in burns. Only unscrew the cap when
generator is cold or there is no more pressure in
the boiler.
- Do not direct steam at people, animals or iron
clothes while they are being worn.
- The use of accessory attachments is not
recommended by Rowenta and may result in fire,
electric shock or personal injury.
liquids.
- The appliance should always be turned off
before plugging or unplugging from outlet.
Never yank the cord to disconnect from outlet,
instead grasp plug and pull to disconnect.
- Always disconnect appliance from electrical
outlet when filling with water or emptying
when not in use.
- Do not allow cord to touch hot surfaces. Let
iron cool completely before putting away.
- Do not operate appliance with a damaged
cord or if appliance has been dropped or
damaged.
- To avoid the risk of electric shock, do not
disassemble the appliance. Ship it to the
nearest authorized Rowenta approved service
center for examination and repair. Incorrect
- Always put the iron with the soleplate down on
the iron rest, never resting on its heel.
SPECIAL INSTRUCTIONS
-This is a 1750 watt appliance.To avoid a circuit 15 ampere cord should be used. Cords rated
overload, do not operate a high wattage for less amperage may overheat. Care should
appliance on the same circuit.
- This unit comes equipped with a 12 foot be pulled or tripped over unintentionally.
power cord and 9 foot steam connection cord. - Your Rowenta appliance is intended for
be taken to arrange the cord so that it cannot
- If an extension cord is absolutely necessary, a household use only.
Save these instructions
3
Notice Pressure iron & steamer 24/08/06 10:14 Page 4
BEFORE USE
Iron and other impurities
Please read all of the instructions for use
and the Important Safeguards carefully.
Remove all packaging from the generator. It
is normal for a small amount of smoke and
a light odor to be produced the first time it is
used. This will quickly disappear.
If your water supply contains large amounts of
iron or organic matter, these minerals can
collect inside the appliance and eventually
appear as brown stains. If you experience
these problems Rowenta recommends using
inexpensive bottled spring water.
1 • Water recommendations
Never use 100% pure distilled water.
Tap water
Always remember :
Rowenta irons are designed to be used with
REGULAR TAP WATER (up to 12 grains of
hardness). If your water is harder than this,
Rowenta recommends mixing half tap water
with half distilled water which reduces the
hardness; or just use inexpensive bottled
spring water. Never use 100% distilled water
as this can cause the iron to spit and leak.
Battery water and water containing additives
(such as starch, perfume or fabric conditioner)
may not be used. Such additives can affect the
properties of the steam and, at high
temperatures, can form deposits in the steam
chamber, which will mark the laundry when
they are emitted through the steam vents.
Descaling liquids/agents should not be used.
Softened water
There are many types of household water
softeners and the water from many of them is
perfectly acceptable for use in the steam
generator. However, some types of softeners,
particularly those that use chemicals such as
salt, can cause the appliance to leak or spit
during use. If you experience this type of
problem, we recommend that you try using
inexpensive bottled spring water or untreated
tap water.
2 • Filling the boiler
The steam generator is designed to operate
using tap water. (A).
While unplugged, place the steam generator
on a stable horizontal, heat resistant surface.
Unscrew the boiler cap.
Using a water pitcher, fill with 33 oz. of water.
Do not fill water tank past the base of the
boiler cap thread. Do not overfill. Be sure that
water does not spill over. If this occurs remove
the excess water.
Once you have changed water it will take
several uses to correct the problem. Rowenta
recommends trying the steam function for the
first time on an old towel or cloth that can be
discarded to avoid damaging your clothes.
Replace the boiler cap and screw it on tightly.
To fill boiler while you are using the
appliance see section “Filling boiler while in
use”.
USE
turn on and off. This is normal as the
temperature is being regulated.The unit is still
on when these lights go out.
To turn the unit off, press the switch(es) in the
opposite direction so that the side without the
light is depressed. Unplug and leave to cool
completely before emptying or putting away.
Set the temperature control dial on the iron to
the minimum setting before unplugging.
3 •Turning on and off
Plug the generator into a 120 volt electric
outlet.
Press on/off switch (B), the iron light and
steam indicator light will turn on.
When the steam indicator light turns off
(approximately 7 minutes), steam is ready.
During ironing the temperature indicator light
for the iron and the steam indicator light will
4
Notice Pressure iron & steamer 24/08/06 10:14 Page 5
4 • Steam ironing
Never iron or steam clothes while they are
being worn.
5 • Dry ironing
This appliance can be used for dry ironing if
the steam button is not pressed.
Set the iron’s on/off switch to the on position.
Do not turn on the steam switch.
The appliance allows steam output to be
adjusted.
• setting on the iron : the steam control dial
should be set to min.
•• setting on the iron : the steam control should
be set at the mid level.
••• setting on the iron : the steam control dial
can be set to the max.
6 • Vertical steam
To remove wrinkles in cotton or linen, the
soleplate can come into contact with the fabric
for optimal results.
For synthetic fabrics, a distance of 4 inches is
recommended to avoid damage to the
garment.
For delicate fabrics, we recommend carrying
out a test on an unobtrusive part of the
garment (inner seam).
IRON THERMO- STEAM CONTROL
TYPE OF FABRIC
STAT SETTING
DIAL SETTING
LINEN, COTTON
WOOL, SILK
•••
Caution : Steam produced is very hot.To
avoid burns and scalding never iron or
steam clothes while they are being worn.
••
•
Fill iron according to the “Filling the boiler”
section of instructions.
Press on/off switch (B), the iron light and
steam indicator light will turn on.
SYNTHETIC
(Viscose, Polyester)
When the steam indicator light turns off
(approximately 7 minutes), steam is ready.
Hang the garment on a coat hanger and hold
the fabric from the bottom of the garment
slightly taut with one hand.
Holding the iron in a vertical position, press
continuously on the steam button while
moving the iron from the top of the garment to
the bottom (C).
Note : It is normal for the connection cord to
become warm during use.
Before using the generator for the first time
or if you have not used the steam function
for a few minutes, press the steam button
several times in a row while holding the iron
away from your clothes.This will enable any
cold water to be removed from the steam
connection cord.
When ironing start with fabrics that require a
low temperature setting (•) and finish with
those which need the highest temperature
(•••).
7 • Filling the boiler while in
use
Caution : Never unscrew the boiler cap while
iron is producing steam and boiler is under
pressure.
Mixed fiber fabrics should be ironed on the
temperature for the most delicate fabric. For
example a shirt that is 60% cotton and 40%
polyester should be ironed at the (•) setting
for synthetics.
If spray starch is used, spray it onto the
reverse side of the garment. Allow starch to
penetrate before ironing.
For best results, use a mesh type ironing
board to allow excess steam to escape.
For delicate fabrics, we recommend carrying
out a test on an unobtrusive area of the
garment such as an inner seam.
Before opening the boiler, ensure that there is
no steam inside. To do this, press the steam
button and keep it pressed until there is no
more steam.
Turn the unit off (see section “Turning On and
Off”) and unplug from outlet.
Slowly unscrew the boiler cap. Using a water
pitcher, fill with 33 oz. of water. Do not fill water
tank past the base of the boiler cap thread. Be
sure that water does not spill over. If this
occurs remove the excess water.
Replace the boiler cap and screw it on tightly.
Plug back in to electrical outlet.
5
Notice Pressure iron & steamer 24/08/06 10:14 Page 6
completely which will take approximately 1
hour.
Once cold, empty water from the appliance
before storing. We recommend emptying the
boiler when not in use.
8 • After ironing
Turn the unit off. (Consult section “Turning On
and Off”).
Unplug the appliance.
Place the iron on the iron rest and allow to cool
MAINTENANCE AND CLEANING
Before cleaning ensure that the appliance is unplugged and completely cooled down.
The iron can be cleaned with a damp cloth and wiped dry. Never use household cleaners,
descalers or solvents.
9 • Cleaning the soleplate
10 • Rinsing out the
boiler
In normal use a draggy coating may build up
on the soleplate (starch, detergent buildup,
burnt synthetic fibers). This can be easily
removed by using the Rowenta Soleplate
Cleaning Kit or a quality hot iron soleplate
cleaner available at most stores.
Do not use descaling agents.
To ensure optimum steam performance, the
boiler must be rinsed out after every 10 uses. If
your tap water is hard increase the frequency.
Check that the generator is unplugged and
cold.
Fill the boiler 3/4 full with tap water.
Shake the boiler for a few moments and then
empty it over a sink (D).
To prevent scratching of the soleplate, do not
iron over sharp objects (zippers, etc.). Do not
place the iron on rough surfaces, e.g. metal
iron support, which may scratch the soleplate.
Place the iron on its rest on top of the base of
the unit.
Always put the iron with the soleplate down on
the iron rest, never place on its heel.
Repeat the process.
Wipe the generator base regularly with a damp
cloth and wipe dry.
Never hold the generator under the tap.
Boiler Cap
To ensure a proper seal, please check the red
rubber ring in the safety cap for wear and
tear regularly. If wear is noted, replace ring.
Replacement rings are available through our
main service centers.
6
Notice Pressure iron & steamer 24/08/06 10:14 Page 7
TROUBLESHOOTING
Issues
Possible causes
Solutions
Water runs through the holes in the
soleplate.
Boiler is too full.
Do not fill the boiler with more than
33 oz. water.
Thermostat isn’t working.
Send appliance to an authorized
service center.
The iron was used before reaching
the required temperature.
Wait for the temperature/steam
control lights to go out before
ironing.
Water has condensed in the steam
tube as iron hasn’t been used for
some time.
Hold the iron away from clothing and
press the steam control button until
iron produces steam.
Steam output control dial is set too
high for the temperature set on the
iron.
Decrease steam output while ironing
at low temperature (•).
The soleplate leave white streaks on
clothing when ironing.
The boiler has a build-up of scale and Rinse the boiler after every 10 uses
needs to be rinsed out regularly.
(see “Cleaning and Maintenance”).
The soleplate leave brown streaks on
clothing when ironing.
Chemical descaling agents or
additives have been used.
Never use descaling agents or
additives. Rinse boiler thoroughly.
Tap water is high in organic matter
such as rust or iron.
Switch to bottled spring water or
rinse boiler more often.
The soleplate has build-up.
Ironing at too high a temperature.
Spray starch build-up.
Refer to the Steam Ironing section of
the instructions for temperature
recommendations.
Spray starch on the reverse side of
the garment.
There is little or no steam.
The boiler is empty.
Fill the boiler.
The boiler is not ready.
Wait for the steam indicator light to
go out before using steam.
Steam escapes from the boiler cap.
Cap screwed on incorrectly.
The seal on the cap is worn.
Unscrew cap when unit is cold and
put back on.
Check cap regularly for signs of wear
and tear to red rubber ring. Replace if
wear is noticed.
If troubleshooting does not assist, before consulting the retailer regarding their return/exchange
policy, please telephone consumer service at 781-396-0600.
7
Notice Pressure iron & steamer 24/08/06 10:14 Page 8
In the interest of improving products, Rowenta reserves the right to change specifications without
prior notice.
LIMITED WARRANTY
All Rowenta products are warranted for 1 year from date of purchase against defects in
material and workmanship. During this period, any Rowenta product that, upon inspection
by Rowenta, is proved defective, will be repaired or replaced, at Rowenta’s option, without
charge to the customer. If a replacement product is sent, it will carry the remaining warranty
of the original product.This warranty does not apply to any defect arising from a buyer’s or
user’s misuse of the product, negligence, failure to follow Rowenta’s instructions, use on
current or voltage other than stamped on the product or alteration or repair not authorized
by Rowenta. Repair or disassembly by anyone other than a Rowenta authorized service
center will void the warranty. THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND
NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE,
ARE MADE BY ROWENTA OR ARE AUTHORIZED TO BE MADE WITH RESPECT TO THE
PRODUCT. If you believe your product is defective, bring the product (or send it, postage
prepaid) along with proof of purchase to the nearest authorized Rowenta Service Center (see
below). If you send the product, please include a letter explaining the nature of the claimed
defect. In the interest of improving products, Rowenta reserves the right to change
specifications without prior notice.
Some states do not allow limitation on how long an implied warranty lasts or do not allow
the exclusion of incidental or consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
Rowenta
196 Boston Avenue
Medford, MA 02155
Tel.: (781)396-0600
OFFICE LOCATION ONLY.
To service product see service center information below.
If your appliance needs service, ship the product to your nearest regional service center. Be sure
to put your name on the outside of shipping box (no P.O. boxes please). If in warranty, Rowenta
will repair or replace product at their discretion. If the product is out of warranty, you will be
advised of the cost of repair before any work begins.
Our main service centers are listed below :
Turnpike Appliance
3495A Lawson Blvd.
Oceanside, NY 11572
516-483-5596
Authorized Appliance
1644 West Ogden Ave.
Downers Grove, IL 60515
630-852-1550
or call our service center information line at 781-306-4620.The information line provides current
service center information and listings in California.
013989 - 30/06
8
|