Installation Overview (Continued)
LightStyle™ Series Model LS-12HBd
High Brightness, Active 3D Home Theater Projection System
Display calibration: adjust the following for each Dimension Digital Controller input and display
mode (resolution/frame rate); save settings when finished:
60 through 79
• Aspect ratio
• Brightness
• Contrast
• Color level
• Tint
• Input position
Quick Setup Guide
15
16
• Color temperature and white balance
IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D VIEWING: Please read and make sure you
understand the following safety information before using the product for viewing 3D content. Provide this
information to the end users of this product and ensure that they understand it.
Prepare Runco Active 3D Glasses for use and test with 3D source material
94
WARNING
It is widely recognized that stereographic display devices can cause discomfort, including, without limitation, dizziness,
nausea, headaches, eye fatigue and eye-strain, in some individuals. The 3D effect and experience will vary by individual,
depending on a variety of factors, including his or her health and vision. Runco recommends that users take regular breaks
when watching 3D video or playing games using stereoscopic displays. Discontinue use if any discomfort occurs. Parents
of young children should ensure their children avoid extensive exposure to electronic stereographic entertainment.
Connecting the Projector and 3D Emitter to the Dimension Digital Controller
Dimension Digital Controller
The quality and appropriateness of the 3D screen materials onto which the image is projected and the quality of the 3D
content being displayed both have a significant and noticeable impact on the overall 3D experience. A properly-calibrated
projection system, including glasses and an optimized third-party screen, displaying high-quality 3D content is the best
formula for immersive and comfortable 3D experiences. Please refer to the LightStyle™ LS-12HBd Installation/
Operation Manual for proper projector installation and usage instructions.
Pri. Display Control
Sec. Display Control
TRIGGERS
2
3D SYNC
IR
1
3
HDMI Out
To Sec. isplay
Compnt / SCART
Y
Video 1
Video 2
The glasses that accompany this product are not safe to use as sunglasses, protective eyewear or any use outdoors or
other than only in conjunction with the proper operation of the Runco product with which they are sold. It is common to dim
the lights in a home theater. Using 3D glasses and the immersive imagery of stereoscopic imagery can increase the risk of
tripping or falling the dark. Special care should be taken.
Video 3
Pb
Pr
HDMI Out
Audio Only
HDMOut
To Pri. Display
HDMI 2
HDMI 4
HDMI 6
HDMI 8
Ethernet
DisplayPort
Do not tilt your head while using the 3D glasses.
Active 3D Emitter
Installation Overview
For Details, Refer to This Page
in the LightStyle™ LS-12HBd
Installation/Operation Manual
Step
Procedure
Choose a location for the projector
21
1
3D SYNC IN
Install anamorphic lens mounting assembly (optional)
Mount the projector
28, 40
33
2
3
4
5
Mount the Dimension Digital Controller
35
RS232
SECONDARY
3D Sync Out
3 D S y n c O u t
Connect the Dimension Digital Controller to the projector (see diagram at right)
36
R S 2 3 2
Y
P R I M A R
Y
S E C O N D A R
Connect other external equipment to Dimension Digital Controller (optional):
• Audio processor or secondary display device
• Control system interface (RS-232)
• 12-volt trigger-activated equipment (retractable screens or screen masking)
• External IR repeater
38
6
• Network hub, router or gateway (Ethernet)
Connect signal sources to the Dimension Digital Controller
Connect the Active 3D Emitter to the Dimension Digital Controller (see diagram at right)
Connect system components to AC power
43
7
49
8
49
9
Apply power to the projector
50
10
11
12
13
14
Adjust primary lens: projected image size (zoom), position (shift) and focus
For rear-screen and/or ceiling-mount installations, select the proper picture orientation
Use Image Alignment controls to fine-tune image geometry
Install and adjust secondary anamorphic lens (optional)
24, 51
51
Note: Runco recommends using the RS-232 communication link between the LS-12HBd projector and the Dimension Digital Controller.
However, display control using HDMI CEC control messages is also possible. For more information on this capability, please contact Runco
Technical Support.
52
54
LS-12HBd Projection System Quick Setup Guide
Page 1
020-1252-00 Rev. A (September 2013)
OSD Menu Tree
Note: Default settings appear in bold type. Settings marked with an asterisk (*) apply to 2D content only.
Color Bars 1
Color Bars 2
Focus
Grey Bars
Full White
Primary / Secondary / Dual
Alignment
3D
Rename/Restore
Remote Code
SRC 1-7 Keys
SRC 8-14 Keys
Installation -
Picture Orientation
Composite 1
Composite 2
Composite 3
Component
HD 1
HDMI 1
HDMI 2
HDMI 3
HDMI 4
HDMI 5
HDMI 6
HDMI 7
HDMI 8
Gain
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Offset
Mode
(Simple / Advanced)
Test Video
Input Source
Aspect Ratio
Simple
(1.8, 2.0, 2.2, 2.35, 2.5)
HD 2
Gamma
SCART
Display Color -
Common Settings
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Input Names
DisplayPort
16:9
00000 ... 08209 ... 65535 or 88999
Remote Control
4:3
Color Temp
Simple (5500K, 6500K, 7500K or 9300K)
(select a key, then choose a source to assign to it)
Letterbox
VirtualWide
Cinema
Auto, REC709, SMPTE-C, EBU, Native or
PCE
Auto, Floor Front, Ceiling Front, Floor Rear or
Ceiling Rear
Focus
Color Gamut*
Red x, y / Green x, y / Blue x, y / White x, y
Yellow x, y / Cyan x, y / Magenta x, y
PCE*
Lamp
Lens
Zoom
Shift
Virtual Cinema
Native
Display Color - Projector
Settings
Display Info.
(read-only)
Lamp Hours Reset
Diagnostics
Altitude
Display 3D Settings
Internal 3D Settings
24Hz 3D Mode
Projector Serial Number
Power (230W or 260W)
Auto Cinema
Display Device -
Configure
Lamp Hours
Yes / No
White, Red, Green, Blue, Yellow, Cyan, Magenta
Auto / High
(n/a)
Sync Delay, Test Pattern Enable
120 Hz 6:4 or 120 Hz 5:5
DHCP (On / Off), IP Address, Subnet Mask,
Default Gateway, Communication Test
Auto Check for New Firmware, Auto Perform
Upgrade, Check for New Firmware
E-Mail Address, Error Notification, Error
Notification to Runco, Periodic Service Notification,
Lamp Life Notification, Customer Information, E-
Mail Calibration Data
Screen 1 / Screen 2
Screen
Picture
Brightness
Contrast
Color
Brightness
Contrast
Color
Input Image
Input Color
-50, -49 ... 0 ... 49, 50
Tint
Tint
Sharpness
Gain
Sharpness
Noise Filter
Left/Right
Up/Down
Width
IP Configuration
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
Offset
Auto Firmware Upgrade
0, 1, 2 ... 7
(Composite inputs only)
Chroma Delay
Noise Filter
Network
Height
0, 1, 2 ... 63
E-Mail Notification
Calibration
Service
Overscan
Save ISF Night
Save ISF Day
Back / Confirm
Memory Preset
Aspect Ratio
Input Position
Overscan Mode
(Zoom/Crop)
Remote Network Control
Auto, REC601, REC709,
RGB-PC or RGB-Video
1 / 2 / 3
On / Off
(Not available on Composite 1, Composite 2 or
Composite 3 inputs)
Copy Settings
Paste Settings
Copy Settings
Paste Settings
Color Space
Triggers
Phase
(RGB/Component/SCART signals only)
Copy/Paste
Tracking
English, Français, Deutsch, Italiano, Español,
(RGB/Component/SCART signals only)
Svenska,
(Simplified Chinese),
Language
(Traditional Chinese), Português,
(Russian),
Recall ISF Night or ISF Day
Left/Right
Up/Down
Width
(Japanese) or
0 (no timeout) or 5, 6, 7 ... 30 ... 60 sec.
On / Off
(Korean)
Memory
Presets
Recall/Save Custom 1 or Custom 2
-50, -49 ... 0 ... 49, 50
OSD Timer
Reset Custom 1 and Custom 2 to
Factory Default
OSD Messages
Blank Screen Color
Sidebar Color
Film Mode
(SD sources only)
CUE
-50, -49, 48 ... 0
Output Shift
Miscellaneous
Red/Green/Blue = 0, 1, 2, 3 ... 255
3D Mode
(Auto, Off, Side-by-Side, Top-and-
Bottom or Frame Packing)
Height
0, 1, 2 ... 100
(Top / Bottom / Left / Right /
Test Pattern Enable)
3D Processing
Sleep Timer
On / Off
Screen Masking
Corner Alignment
Midpoint Alignment
Reverse Eyes (On/Off)
On / Off
Off, 30 Minutes, 60 Minutes, 90
Minutes, 2 Hours or 4 Hours
(Chroma Upsampling Error)
Top Left / Top Right / Bottom Left /
Bottom Right / Test Pattern Enable
0, 1, 2 ... 15
Sync Threshold
HDMI EDID Extension
Audio Format
(HD 1, HD 2 and Component inputs only)
On / Off (per HDMI and DisplayPort input)
Combined / HDMI Out (Pri. Display) /
HDMI Out (Sec. Display) / HDMI Out (Audio Only)
On / Off
Signal
Image Alignment
Adjustment Mode
Center / Top Middle / Left Middle /
Right Middle / Bottom Middle /
Test Pattern Enable
System
Network
Information
HDMI
Field Service
Manufacturing
Both, Primary or Secondary
Owner Name
CEC
HPD Toggle Rejection
Logo LED
Auto / On / Off
0 (off), 1, 2 ... 31
On / Off
0 (off), 1, 2, 3 or 4
On / Off / No Signal
1, 2, 3, 4, ... 23, 24
ISF Calibrated
ISF Other
Front Panel Brightness Standby LED
LCD
Splash Configure
OSD Position
Splash Timer
5, 6, 7 ... 15 ... 59, 60
On/Off
Enable
Hours
Low Power / Fast Startup
Auto Power Off
Splash Enable
Hor. / Ver.
Standby Mode
System Reset
0, 1, 2 ... 100
LS-12HBd Projection System Quick Setup Guide
Page 3
020-1252-00 Rev. A (September 2013)
Serial Communications
Command
Description
Picture Adjust Commands (Calibration -> Input Image menu)
Sets a value for brightness
(BRT=[-50...+50])
(CLR=[-50...+50])
(CON=[-50...+50])
(SHP=[-50...+50])
(TNT=[-50...+50])
Connect your control system or PC to
Note
Pri. Display Control
Sec. Display Control
Sets a value for color
RS-232
the RS-232 input of the Dimension
Digital Controller as shown in the
diagram at right.
IR
Sets a value for contrast
PC / Control
HDMI Out
HDMI 5
HDMI 7
To Sec. Display
Sets a value for sharpness
Configure the RS-232 controller or PC
serial port as follows: no parity, 8 data
bits, 1 stop bit and no flow control. Set
the baud rate to 19200.
Sets a value for tint
5
4
3
1
2
Image Preset Commands
HDMI Out
Audio Only
Out
splay
HDMI 6
HDMI 8
6
Ethernet
9
8
7
(MMP=2) or (KEY=50)
(MMP=3) or (KEY=51)
(MMP=1) or (KEY=49)
(MMP=0) or (KEY=48)
Loads “Custom 1” image preset
Loads “Custom 2” image preset
Loads “ISF Day” image preset
Loads “ISF Night” image preset
3D Mode Commands
The following is a partial list of
supported serial commands. For a
complete list, refer to the LightStyle™
LS-12HBd Installation/Operation
Manual.
2 Receive Data
(to ctrl. system)
3 Transmit Data
(from ctrl. system)
to Automation/
Control System
or PC
5 Ground
(none of the other pins are used)
All commands must be followed by a carriage return character.
(TDM?)
Returns the 3D mode setting
Sets the 3D mode setting
(0 = Auto, 1 = Off (2D), 2 = Side-by-Side, 3 = Top-and-Bottom, 4 = Frame Packing)
(TDM=[0...4])
Command
Description
Power On/Off Commands
Turns projector off
Turns projector on
Input Selection Commands
Screen Commands
Returns the screen setting
(PWR=0) or (KEY=2)
(PWR=1) or (KEY=1)
(SCN?)
(SCN=0) or (KEY=38)
(SCN=1) or (KEY=39)
Sets the screen to Screen 1
Sets the screen to Screen 2
Miscellaneous Commands
Returns display device name
Returns input resolution
(INS=3) or (KEY=14)
(INS=0) or (KEY=13)
(INS=1) or (KEY=24)
(INS=2) or (KEY=25)
(INS=7) or (KEY=19)
(INS=8) or (KEY=20)
(INS=9) or (KEY=21)
(INS=10) or (KEY=22)
(INS=11) or (KEY=81)
(INS=12) or (KEY=82)
(INS=13) or (KEY=83)
(INS=14) or (KEY=84)
(INS=15) or (KEY=85)
(INS=4) or (KEY=17)
(INS=5) or (KEY=18)
(INS=6) or (KEY=23)
Selects the Component input
Selects the Composite 1 video input
Selects the Composite 2 video input
Selects the Composite 3 video input
Selects the HDMI 1 input
(IDN?)
(IIR?)
(MDL?)
Returns product model name
Returns output resolution
(IOR?)
Selects the HDMI 2 input
(RMN=[0...65535])
(RMN?)
Sets the remote code
Selects the HDMI 3 input
Returns the remote code
Selects the HDMI 4 input
(ISN?)
Returns Dimension Digital Controller serial number
Returns firmware version number
Selects the HDMI 5 input
(IFV?)
Selects the HDMI 6 input
12-volt trigger configuration:
[1...3] = Trigger number
[1...7] = Aspect ratio (1 = 16:9, 2 = 4:3, 3 = Letterbox, 4 = VirtualWide, 5 = Cinema,
6 = Virtual Cinema, 7 = Native)
[0...1] = On/off (0 = Cancel previous assignment, 1 = assign)
Selects the HDMI 7 input
Selects the HDMI 8 input
(T[1...3][1...7]=[0...1])
Selects the DisplayPort input
Selects the RGB HD 1 input
Selects the RGB HD 2 input
Selects the SCART input
Example: (T15=1)[CR]assigns Trigger 1 to Cinema aspect ratio.
The following serial commands are used to emulate buttons on the remote control or Dimension Digital Controller front panel.
Each button has its own serial command, so effectively it is as if you were using the IR remote.
These commands provide active OSD responses just like IR remote commands.
Aspect Ratio Commands
Selects the 16:9 aspect ratio
(KEY=6)
(KEY=4)
(KEY=52)
(KEY=7)
(KEY=3)
(KEY=8)
(KEY=5)
Down-Arrow ( ) key
ENTER key
(ASP=1) or (KEY=9)
(ASP=0) or (KEY=10)
(ASP=4) or (KEY=44)
(ASP=2) or (KEY=11)
(ASP=6) or (KEY=46)
(ASP=3) or (KEY=12)
(ASP=5) or (KEY=45)
(ASP=7) or (KEY=86)
Selects the 4:3 aspect ratio
EXIT key
Selects the Cinema aspect ratio
Selects the Letterbox aspect ratio
Selects the Native aspect ratio
Left-Arrow ( ) key
MENU
Right-Arrow ( ) key
Up-Arrow ( ) key
Selects the VirtualWide aspect ratio
Selects the Virtual Cinema aspect ratio
Selects the Auto Cinema aspect ratio
© Copyright 2013 Runco International. All rights are reserved.
Trademarks and registered trademarks used in this document are the property of their respective owners.
LS-12HBd Projection System Quick Setup Guide
Page 4
020-1252-00 Rev. A (September 2013)
|