SECO-LARM BALL-MOUNT IR DOME CAMERA Manual
TROUBLE SHOOTING
The screen is blank
• Check that the camera is powered up.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is connected properly.
SECO-LARM
The screen image is dim
• Clean the lens (using a soft, clean cloth).
• Check that the light source is adequate.
EV-122C-DXB3Q
The screen image has poor contrast • Adjust the monitor’s contrast knob.
• Change the position of the camera.
Multi-Axis Ball-Mount Color Dome Camera
The screen image flickers
The screen image is distorted
The camera case is hot
• Change the position of the camera.
• Change the position of the camera.
• Check that the correct power supply is in use.
MANUAL
IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or statutes.
WARNING Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or
electric shock. Do not open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT Information to the user: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARRANTY
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited
to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that
such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal
or property damages of any kind to the purchaser or anyone else.
Multi-Axis ball mount for
wall or ceiling mounting
360° Rotation, 10°~120° tilt
3.6mm Lens
•
•
•
•
•
NOTICE
24 IR LEDs
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
•
•
50ft (15m) IR range
Concealed wiring
1/3” Sony Super HAD II CCD
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
®
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
PICSN4
Website: www.seco-larm.com
E-mail: sales@seco-larm.com
MiEV-122C-DXB3Q_0914b.pmd
Note: Products with model number that ends with "Q" or have a round green "Q" sticker represents RoHS compliant products.
|