Use the loop
Turn the headset on/off
Wear the headset
Features and
Troubleshooting
To turn the headset on,
Wear the headset on your ear.
In general, you will get better performance
when there are no obstructions
(including parts of your body)
between the headset
You can replace the original earpiece cover with the
supplied loop earpiece cover. Depending on what ear
you are going to wear the headset, simply adjust the
loop accordingly.
Functions Guide
Press and hold the Multi-Function button for
4 seconds until you see 4 blue flashes on the
indicator light, then release.
You will hear a tone and see the indicator light
flashes while the power is on
My phone does not find my headset.
Make sure the blue indicator light on your
headset turns on when your phone is
searching for devices.
SAMSUNG
Bluetooth® Headset
and the phone.
(see Meaning of the indicator light of this guide).
My headsest worked before but now it is
not working.
WEP210
To turn the headset off,
Make sure your phone is on and the Bluetooth
feature is turned on in your phone.
If the Bluetooth feature has been turnned off
or was turned on only temporarily, you may
need to restart the Bluetooth feature.
If you have confirmed the Bluetooth feature is
on in your phone, pair your phone and
headset again.
Press and hold the Multi-Function button for
4 seconds until you see blue and red flashes on the
indicator light, then release.
You will hear series of 2 tones and see the indicator
light stops flashing.
Important:
Be sure to first follow the
Quick Start Guide on
the reverse side of this guide
to complete initial setup
of your headset.
S
Right
S
Left
Make calls
Meaning of the indicator light
Use enhanced features
Light
Status
Tone
Enhanced features are available for phones that support the
Hands-Free Profile and enhanced features.
Make a voice activated call
If the phone’s voice recognition feature is on, you can
make a voice activated call.
End a call
Press the Multi-Function button.
Flashes in
blue every
8 seconds.
Quick series
of 2 tones.
(Active mode
starts.)
The headset is in Active mode.
• Reject a call
• The headset has an active
call in progress.
• You can talk up to 4 hours.*
Answer a call
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
When you receive a call, press and hold the Multi-Function
button.
Depending on your phone’s setting or type, you may only
be able to mute the ringer or this feature may not be
supported.
1
Press and hold the Multi-Function button. You will hear
the voice-activation tone.
When a call comes in, the headset sounds the ring tone and
flashes the blue indicator twice. Press the Multi-Function
button.
Flashes in
Quick series
The headset is in Standby mode.
2
Say the name of the person you wish to call.
blue every 3 of 2 tones.
Internet Address:
accessories
• The headset is waiting
for a call.
• The headset can be in
Standby mode up to 70
hours.*
seconds.
(Standby
mode starts.)
Depending on your phone, this feature may not be
supported.
Do not hold the Multi-Function button down too long when
making a call with your voice, ending, or answering a call.
This should only be a quick tap.
• Answer a second call
When your phone notifies you of another incoming call while
you are on a call, press and hold the Multi-Function button to
answer the second call.
You can switch between calls by pressing and holding it.
Depending on your phone, this feature is not supported.
Customer Care Center:
1-888-987-4357
Redial the last number
Adjust the volume
Press [Volume Up] on the side of the headset to increase
Press the Multi-Function button. When you release the
button, the phone dials the last dialled or received
number.
Flashes in
red.
5 tones every The battery of the headset is
20 seconds.
low.
the volume level and press [Volume Down] to decrease the
volume level.
• There is less than 10% of
battery power left. Recharge
the battery.
• Place a call on hold
Depending on your phone, how to redial the last number
may vary.
While you are on a call, press and hold the Multi-Function
button. To retrieve the call, press and hold the Multi-Function
button again. Depending on your phone, this feature may not
be supported.
*
Depending on the phone type and usage, the actual time
may vary.
Before using your headset
Check the accessories
Charge your headset
Thank you for purchasing the Samsung Bluetooth
Mono Headset WEP210. We hope you will be
delighted with its operation.
Take a moment before you get started to
familiarize yourself with your new headset.
Make sure you have the following items with your
headset:
Charge the headset's battery fully before using
the headset for the first time.
2
3
Plug the travel adapter into the electrical
outlet.
Quick Start Guide
Bluetooth® Headset
WEP210
Get connected in 4 quick steps
Travel Adapter, User’s Guide
1
Plug the travel adapter into the jack on the
headset.
• Charge the headset until the red light on the
headset turns to blue.
• The headset will be fully charged in
approximately 2 hours and 30 minutes.
Samsung
The items supplied with your headset may vary, depending
on your country or service provider.
Volume Up
Multi-Function
button
Remove the travel adapter from the headset.
button
Indicator light
Earpiece
• The headset cannot be used while charging.
• Use only a Samsung-approved charger or adapter.
• Bluetooth version: 2.0 (compatible with devices of
Bluetooth version 1.1 or higher)
• Supported Bluetooth Profiles:
- Headset Profile
Charge your headset
Volume Down
button
Put your headset in pairing mode
Turn on Bluetooth on your phone and
pair with headset
- Hands-Free Profile
Test and use
Adapter jack Microphone
Start here
Put your headset in
pairing mode
Before you can use your headset, you must pair it
with your phone.
Turn on Bluetooth on your
phone and pair with headset
Test and use
Your phone and headset are now paired and
ready to make and receive calls. To confirm
they are operating properly, make a call:
1
Set your Bluetooth phone to discover the
headset by following your phone's guide.
Using your WEP210
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
1
Place the headset over your ear.
See Wear the headset on the reverse
side of this guide.
Typically, the steps involve going to the Settings,
Connection, or Bluetooth menu on your
phone and then selecting the option to discover
Bluetooth devices.
1
2
Ensure that the headset is off (see Turn
headset on/off on the reverse side of this guide).
See Features and Functions Guide
on the reverse side of this guide
for information on using your
WEP210.
Press and hold the Multi-Function button until the blue
indicator light stays on after blinking.
Internet Address:
accessories
2
3
On your phone, make a call to the number
you want.
Your phone will find the Samsung WEP210
headset and ask if you want to pair with it.
Confirm this by pressing the Yes or OK key.
If your phone and headset are successfully
paired, you will hear ringing on the headset.
Customer Care Center:
1-888-987-4357
2
Enter a passkey or PIN, 0000 (4 zeros), then
press the Yes or OK key.
After you have successfully paired your phone
and headset, you do not need to repeat these
initial setup steps each time you use the
headset.
Guide No.: GH68-12949A
11/2006. Rev. 1.0
|