About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
INFORMATION TO USER
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THIS UNIT.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Pour la clientèle canadienne
Cet appareil numerique de la Classe B est conforme a la norme
NMB-003 du Canada.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by Sanyo may
void the user’s authority to operate this camera.
This installation should be made by a qualified service person and
should conform to all local codes.
English
PRECAUTIONS
In case of problem
Protect from humidity and dust
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).
To prevent damages to the camera, do not install it where there is
greasy smoke or steam, where the dampness may get too high, or
where there is a lot of dust.
Protect from high temperatures
Do not open or modify
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damages.
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For internal settings and repairs, consult your dealer (or a
Sanyo Authorized Service Centre).
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels.
Do not put objects inside the unit
Install where the temperature range will stay between –10°C and
50°C.
(no condensation)
Make sure that no metal objects or flammable substance get inside
the camera. If used with a foreign object inside, it could cause a fire,
short-circuits or damages.
If water or a liquid gets inside the camera, disconnect the power cord
immediately, and consult your dealer (or a Sanyo Authorized Service
Centre). Be careful to protect the camera from rain, sea water, etc.
Cleaning
• Dirt can be removed from the cabinet by wiping it with a soft
cloth. To remove stains, wipe with a soft cloth moistened with a
soft detergent solution and wrung dry, then wipe dry with dry soft
cloth.
Be careful when handling the unit
To prevent damages, do not drop the camera or subject it to strong
shock or vibration.
• Do not use benzine, thinner or other chemical product on the
cabinet, as that may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes in
contact with the cabinet for a long period of time, as that may
cause damage or paint peeling.
Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, audio speakers the magnetic field they generate will
distort the image.
English
PARTS NAMES
1 Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.
2 Power input terminal
4
3
1
24 V AC input terminal (AC 24 V, GND)
3 External sync composite video signal input connector (VBS IN: BNC type)
Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite
signal of a video distributor.
2
4 Power indicator (POWER)
Comes on when the power to the camera is on.
English
PARTS NAMES
5 Lens mount cap
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens (sold separately).
6 Flange-back adjustment screw (FLANGE BACK ADJ.)
7 Flange-back lock screw (FLANGE BACK LOCK)
8 Camera installation bracket
7
5
8
6
2
2
The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the
longer screws and install the shorter screws on the opposite side to seal the openings.
3
1
CAUTION:
When installing the camera support, select a location that can support the total weight of the
camera and accessories.
1
1 Shorter screws: M3 x 4
2 Longer screws: M3 x 6
3 Camera mounting screw
hole: 1/4"-20 UNC
English
PARTS NAMES
9 Lens iris output connector (LENS)
This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.
F
F Camera setup section (under the cover)
9
These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However,
if due to installation conditions or environment the settings may need to be modified for best results (see
"SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover.
NOTE: When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the
A.I. LENS switch to the VIDEO position.
English
CONCERNING AUTO-IRIS LENSES
DC type auto-iris lens
A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is
referred to as DC type coil lens or DC type non-amplifier lens.
(Set the A.I. LENS switch to the DC position.)
VIDEO type auto-iris lens
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is
referred to as EE amplifier type lens.
ALC and LEVEL volume level controls are available on the lens for iris adjustments.
(Set the A.I. LENS switch to the VIDEO position.)
Compatible auto-iris lenses
1/3 inch Sanyo DC type lens
VCL-CS8LY: Standard angle, f= 8 mm
VCL-CS4LY: Wide angle, f= 4 mm
VIDEO type lens
Standard angle, f= 9 mm
Telephoto angle, f= 12 mm
VCL-CS2LY: Ultra-wide angle, f= 2.8 mm
Greater telephoto angle, f= 16 mm
If using a VIDEO type auto-iris lens
• Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned
all the way to Av (Average).
• Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL
volume on the lens casing to correct.
English
MOUNTING THE LENS
Please use a DC type auto-iris lens (sold separately).
Check the lens mount
Do not use a lens if the length “L” is more than 5 mm. That may damage the
camera and prevent proper installation.
1
2
Remove the lens mount cap from the camera.
Install the auto-iris lens.
CS mount type lens
Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.
C mount type lens
To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully
align the lens mount with the camera opening and turn the lens slowly to install it.
3
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.
When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.
In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug
according to the diagram. (Refer to page 9.)
English
MOUNTING THE LENS
Rewiring the lens cable in the lens iris plug
1
2
Prepare the lens cable.
Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.
Install the lens iris plug.
Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close
the plug cover.
Pin layout
DC type lenses
VIDEO type lenses
+12 V DC (50 mA max.)
Brake coil (–)
Brake coil (+)
Drive coil (+)
Drive coil (–)
1
2
3
4
2
4
1
3
2
4
1
3
Not used
Video output (1.0 Vp-p, high impedance)
Ground (for video signal and DC power)
Flange-back adjustment
If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of
focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the
flange-back position as described below.
1
2
3
4
Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+).
Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.
Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. screw.
Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the FLANGE BACK LOCK screw.
English
CONNECTIONS
(Video signal connections)
: VIDEO IN
: VIDEO OUT
Coaxial cable type and maximum length
• Cable type RG-59U (3C-2V), 250 m maximum.
• Cable type RG-6U (5C-2V), 500 m maximum.
• Cable type RG-11U (7C-2V), 600 m maximum.
Basic connection for monitoring or recording
The peripheral devices (VCR, monitor, lens, etc.), AC adaptor
and cables are sold separately.
1
2
Make the video signal connection between the camera and
the monitor or time lapse VCR.
CAUTION:
• The RG-59U type cable should not be run through electrical
conduits or through the air.
Use a commercially available 24 V AC adaptor.
Connect an AC 24 V power source to the AC 24 V input terminal
on the back of the camera.
• Using CCTV/Video-grade coaxial cable.
3
Insert the plug of this power cord into a wall outlet.
The POWER indicator (A) will light. Adjust the picture on the
monitor using the Brightness and Contrast controls etc.
English
SETTINGS
The illustration shows the factory default settings for the switches in the camera setup section.
The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be
sure to read the Note which is given.
6
7
9
Control
namePosition
1/60 sec.
NORM
High speed electronic shutter (ES) setting
1
2
Gain up setting
(HI: High/NORM: Normal)
Aperture compensation setting
(SHRP: Sharp/NORM: Normal)
NORM
3
4
5
6
Backlight compensation mode setting (BLC)
(Multi: MULT/OFF)
OFF
OFF
Backlight compensation mode setting (BLC)
(Center: CENT/OFF)
1 2 3 4 5 6 7 8
White balance switch (WB) and colour
(R or B) adjustment volume
ATW
ES/EI
2
GAIN APER
HI SHRP MULT CENT MANU 180
BLC
WB
SC-PHASE1
External sync setting (SC-PHASE1)
External sync horizontal adjustment (H)
Auto-iris lens setting (A.I. LENS), see page 7
Lens iris level adjustment
adjustable
adjustable
DC
7
7-a
8
1
3
90
MSB
LSB NORM NORM OFF
OFF ATW
0
0
adjustable
9
* The sticker on the inside of cover.
English
SETTINGS
Table A (switch 1 ~ 3)
Electronic shutter settings and electronic iris
AI
1/60 1/100 1/500 1/1000 1/2000 1/4000 1/10000
settings 1
EI
When all of these switches are down, electronic shutter (1/60 sec or
auto iris setting) is enabled. The electronic shutter can be set to one
of 7 speeds as shown in Table A.
(Unit: sec.)
Furthermore, when all switches are up, electronic iris setting is
enabled.
Gain up setting 2
Notes on the electronic shutter:
Switch 4 should normally be set to “NORM”. If the monitoring
location is dark and you would like to increase the luminance
(brightness), set switch 4 to “HI”.
• Using the high speed electronic shutter indoors with low lighting,
will give darker pictures. In such a case, add some lights to make
sure the lighting is sufficient. If the lighting is very bright, pay
attention to the light angle in order to avoid or minimize the
smear phenomenon effect.
Note: If switch 4 is set to “HI”, the images from the
monitoring location will become brighter, but
interference may become more noticeable.
• Use a manual or fixed iris lens and set the lens aperture to the
shortest F stop. Set the switch (1 – 3) to the up position.
4
• The electronic iris is suitable for normal indoor use. When the
switch (1 – 3) is set to the up position, do not use an auto-iris lens.
Aperture 3
• If used under fluorescent light, the image may flicker. In such a
case, change to incandescent lighting or set the switch (1 – 3) to
the down position and use an auto-iris lens.
This switch 5 (APER) is normally set to the down
(NORM) position. If you would like to emphasize the
contours of the object, set the switch 5 (APER) to the
up (SHRP) position.
• If conditions are outside the electronic iris operation range or
more than the maximum illumination, it will cause saturation of
the CCD. In that case, use a manual iris lens.
5
English
SETTINGS
(MULTI mode: 48 sections)
Backlight compensation setting 45
This camera has two different backlight
compensation functions: Normally backlight
compensation switch 6 (MULT) and 7 (CENT)
are set to the down (OFF) position. Change
the backlight compensation switch settings
depending on the conditions.
6
7
• MULT mode: Use this position when applying backlight
compensation to the whole of the screen.
(CENT mode)
• CENT mode: Use this position when applying backlight
compensation to only the central portion of the
screen.
Note:
• When using the backlight compensation function, set the switch 6
or 7 to the up position. When not using the function, set the
switch 6 and 7 to the down (OFF) position.
• When MULTI mode is set, scenes with no backlighting may
appear extremely dark and the object may appear over-exposed. If
this happens, move the switch 7 to the up (CENT) position.
If using a VIDEO type auto-iris lens
• The ALC volume on the lens should be turned all the way to Av
(Average).
• If the backlight compensation function does not compensate
properly for the conditions, set using the LEVEL volume on the
lens.
English
SETTINGS
White balance adjustment 6
External sync adjustment (VBS) 7
Normally the switch 8 (WB) is set to the down (ATW: auto white
balance) position and the white balance is adjusted automatically. If a
manual white balance adjustment is necessary, follow the steps below.
1
2
Connect the VBS signal output for the other camera to the VBS IN
connector at the rear of this camera.
If the signals are not synchronized, change the sub-carrier
(SC-PHASE) switches as follows.
Set the switch 8 (WB) to the up (M: manual) position, then adjust the
colour.
Setting
9-pin
OFF (down)
OFF
10-pin
OFF
• Turn RED (VR302) to set the red ratio and/or BLUE (VR303) to set
the blue ratio.
Default
Set to 90° counterclockwise
Set to 180° counterclockwise
Set to 270° counterclockwise
ON (up)
OFF
ON
ON
ON
8
9
10
Note:
• The sub-carrier switches let you make broad adjustments to the
sub-carrier phase. If finer adjustments are required, contact the
place of purchase.
• The type and length of the cable which is connected to the VBS
connector may cause the horizontal synchronization being out of
phase. If this happens, adjust VR304 (H: horizontal sync).
English
SETTINGS
Lens iris adjustment 9
If using a DC type auto-iris lens, you will need to set the LEVEL
(VR301) volume when shooting in the conditions described below.
L (counterclockwise): To decrease the contrast
H (clockwise): To increase the contrast
• If shooting simultaneously in a dark room and through a bright
window.
• If the subject background is extremely bright or dark.
• If the brightness of the picture on the monitor is not correct.
English
TROUBLESHOOTING
Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please
consult your dealer or a Sanyo Authorized Service Centre.
No picture on the monitor screen
• Is the power turned on to all connected devices? Is the voltage correct?
• Are all the signal connecting cables correctly connected?
• Is the lighting sufficient?
• Has the lens cap been removed?
• Is the lens type (DC or VIDEO) correctly selected?
Depending on the type of lens, the A. I. LENS switch must be set accordingly.
• Is the iris control correctlbntrrA52T2TH2Trbntrx%G2ꢀ T +%H5N4r e 2:F4P2HFVa0P:HAHTx5F4PnI02VHN(xD0T j 52A
•
SPECIFICATIONS
Camera:
Environmental
conditions
: Temperature: –10°C ~ +50°C
Humidity: less than 90% (no condensation)
Scanning system
: NTSC standard TV system
(525 TV lines, 30 frames/sec.)
Power supply
: 24 V AC, 60 Hz
Power consumption : Approx. 2.8 W (with auto iris lens)
Interlace
Image device
Picture elements
Effective picture
elements
: PLL 2:1 interlace
: 1/3 inch solid state image device CCD
: 811 (H) x 508 (V)
Approx. 2.1 W (without auto iris lens)
Weight
Dimensions
: Approx. 310 g (without lens)
: 768 (H) x 494 (V)
Synchronizing system : Internal sync, External sync, Automatically
switchable
Resolution
Video output level
Video S/N ratio
: 520 TV lines horizontally, 350 TV lines vertically
: 1.0 Vp-p/75 ohms, composite
: More than 48 dB
Minimum required
illumination
(incandescent
lighting)
: Approx. 0.3 lux with a F 1.2 lens (GAIN, HI)
Approx. 0.6 lux with a F 1.2 lens (GAIN,
NORM)
Backlight
compensation
: Manual MULT/CENT/OFF switching (Active
when using an auto-iris lens)
Iris function
: AI/EI selectable by switches (Electronic shutter)
Features and specifications are subject to change without prior
notice or obligations.
Electronic iris range
Electronic shutter
: 0.6 lux to 50,000 lux (F 1.2 lens)
: 7 speeds, selectable by switches:
(1/60, 1/100, 1/500, 1/1000, 1/2000,
1/4000, 1/10000 sec.)
SERVICE
This camera is a precision instruments and if treated with care, will
provide years of satisfactory performance. However, in the event of a
problem, the owner is advised not to attempt to make repairs or open
the cabinet. Servicing should always be referred to your dealer or
Sanyo Authorized Service Centre.
Flange-back
White balance
Lens mount
AGC gain
: 12.5 mm 0.5 mm
: ATW/Manual switching
: CS mount
: HI/NORM
English
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at
Printed on recycled paper
1AC6P1P2624--
L53H4/US2(0103KPS-CZ)
Printed in Japan
|