TRADEMARKS ________
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK
OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
RISK OF ELECTRIC SHOCK DO NOT OPEN!
CAUTION
Manufactured under license from Dolby
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTE-
NANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.
CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Laboratories. “Dolby” is
Dolby Laboratories.
a
trademark of
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
15. If an outside antenna is connected to the television equipment,
be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges.
In the U.S. Selection 810-21 of the National Electrical Code pro-
vides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrodes.
class
(38.5”diagonal)
HDMI, the HDMI Logo and High-Definition
Multimedia Interface are trademarks or regis-
tered trademarks of HDMI Licensing LLC in
the United States and other countries.
Model No.:
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
DP39843
SANYO television customers
Owner’s
Manual
(English)
should
Recycling at 888-769-0149 or
visit their website at
contact
MRM
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit fully into your out-
let, consult an electrician for replacement of the obsolete outlet.
16. An outside antenna system should not be located in the vicini-
ty of overhead power lines or other electrical light or power
circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or cir-
cuits as contact with them might be fatal.
regarding SANYO’s waste
management plan.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
1080p HDTV LCD
10. Protect the power cord from being walked on or pinched par-
ticularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
1JC0P1P0043 - -
Part No.:
© 2013 Sanyo Manufacturing Corporation
11. Only use attachments/accessories specified by the
manufacturer.
Please read before operating your HDTV!
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate nor-
mally, or has been dropped.
“Note to CATV system installer:
SPECIFICATIONS
PROTECTING THE LCD
POSITIONING THE HDTV
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical.”
NOTE: Design and specifications are
subject to change without notice.
SCREEN
Always use a firm and flat surface when
positioning your HDTV.
•
CAUTION: The screen can be damaged if
Power Requirement:
Source: AC 120V, 60Hz
it is not maintained properly.
Do not position the unit in a confined
area.
•
17. Wall or Ceiling Mounting—The product should be mounted to
a wall or ceiling only as recommended by the manufacturer.
18. Apparatus shall not be exposed to dripping or splashing, and no
objects filled with liquids, such as vases, shall be placed on it.
19. When the MAINS plug is used as the disconnect device, the
disconnect device shall remain readily operable.
Do not use hard objects such as hard
cloth or paper to clean the screen.
•
•
AC Power Consumption: 120 watts
Allow adequate space for proper venti-
lation.
•
•
Weight: 24.5 lbs (w/stand)
Do not use excessive pressure when
cleaning the screen; excessive pressure
can cause permanent discoloration or
dark spots.
Do not position the HDTV where it is
easily reachable by small children and
may present risk of injury.
Dimensions _________________________
WIDTH HEIGHT DEPTH
w/stand
36.7
25.1
22.8
8.8
4.3
NEVER spray liquids on the screen.
Once HDTV is positioned, remove the
protective film covering front cabinet.
•
•
FCC INFORMATION ________________________________________________
w/out stand
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
HANDLING PRECAUTIONS
Handle by the cabinet only.
NOTE: Dimensions are in inches.
•
The American Academy of Pediatrics dis-
courages media use by children younger
than two years. For more information,
Handling by two or more people is rec-
ommended.
•
– Reorient or relocate the receiving antenna.
Never touch the screen when handling.
•
•
CONTAINS MERCURY
LAMPS, DISPOSE OF
PROPERLY
– Increase the separation between the equipment and receiver.
Handling damage is not covered under
warranty.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority to
Do not remove the protective film
covering the front cabinet while
handling the HDTV.
•
operate the unit.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require
a safety connection to electrical earth.
GETTING STARTED
STAND ASSEMBLY ______
NOTE: Skip these steps if you are wall
BATTERY INSTALLATION
Install two (2) “AA” batteries in the
remote control. (Not included)
INITIAL CHANNEL SEARCH
HDTV INPUT/OUTPUT REFERENCE ________________________________________
Before proceeding, please make
sure to correctly hook up your
antenna or cable connection and
all AV equipment to your HDTV.
ANT Analog / Digital Antenna Input
Hook up your indoor or outdoor digital antenna, or a direct
Cable service (Analog or ClearQAM).
mounting the TV.
1
HDTV SIDE PANEL
PRECAUTIONS:
Place HDTV face down on
a
• Replace both batteries at the same
time. Do not use a new battery with a
used battery.
1
1
2
padded or cushioned flat surface
to protect the screen and finish.
1. PLUG IN AC POWER CORD
120V AC, 60Hz
2
VIDEO INPUT (COMPONENT/COMPOSITE combo)
Carefully insert the stand base to
the bottom of the HDTV and secure
it by inserting four (4) screws as
indicated in the diagram below.
COMPOSITE Connection
• There’s a risk of explosion if a battery
is replaced by an incorrect type.
2. TURN ON TV
(VIDEO)
A Composite connection is used to hookup your analog
equipment such as a VCR or an older DVD player.
3. TV SET LOCATION SELECTION:
Select “Home Mode” to set the
HDTV’s backlight to a lower energy
consumption level, or select “Store
Mode” to set the backlight to a retail
high brightness display level.
• Keep away from moisture.
Match the YELLOW connector from your external device to
the GREEN Y-VIDEO jack on the HDTV.
• Be sure to match the “+” and “–”
signs on the batteries with marks
inside the remote control.
NOTE: Stand base screws are located
in the literature package.
2
3
NOTE: Use the WHITE and RED (L and R) jacks for AUDIO signal.
(DVI AUDIO)
• Please properly dispose of used up
batteries.
COMPONENT Connection
4. CHANNEL AND SIGNAL SEARCH:
Select “Signal Search” and press
ENTER to perform a channel search
from an Antenna or a direct Cable
connection, and a signal search
from devices hooked up to the
HDTV’s AV input jacks.
A Component connection will accept SDTV, EDTV and
HDTV video signals. Use it for great image quality from di-
gital devices such as a DVD player or Video Game system.
WARNING: The batteries (or battery
pack) shall not be exposed to excessive
heat such as sunshine, fire or the like.
HDMI
INPUT2
Match your digital device’s Component output jacks to the
Component input jack set on your HDTV.
HDMI
(DVI)
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
Hook up your antenna or your cable
service to the HDTV’s ANT terminal
with the use of a 75 OHM coaxial cable.
NOTE: Use the GREEN (Y), BLUE (Pb) and RED (Pr) jacks for the
VIDEO signal and the WHITE and RED (L and R) jacks for
the AUDIO signal.
INPUT1
Position the HDTV on a firm and
5. SIGNAL SEARCH RESULT SCREEN
3
flat surface with adequate space
for proper ventilation.
The final setup screen displays ana-
log and digital channels found, as
well as AV inputs detected.
Select Finish Setup and press
ENTER.
4
5
3
HDMI (INPUT1 or INPUT2)
Use HDMI INPUT1 & 2 to hookup HD digital devices such as
a Blu-ray player, HD Cable Box, HD Satellite Receiver or
Video-game System.
Connect your digital device’s HDMI output to any of the two
(2) HDMI inputs on your HDTV’s side panel with the use of
an HDMI cable.
WALL MOUNTING (OPTIONAL)
Wall mounting of the HDTV must be
performed by a skilled person.
NOTE: Keep your indoor antenna at
least 3 ft. away from the televi-
sion set and any other electron-
ic equipment.
HDTV BACK PANEL
NOTE: If you wish to repeat the
process, select Repeat.
If stand base disassembly is required:
Place HDTV face down on a padded or
cushioned flat surface to protect the
screen and finish.
•
•
ANTENNA
Channel Search Result: Succesfully Completed
NOTE: A DVI connection is possible via the HDMI (DVI) INPUT1
using an appropriate cable or adapter and connecting the
audio to the L and R (VIDEO INPUT) jacks.
DIGITAL
AUDIO OUTPUT
Analog Channels 16
Digital Channels 26
Remove the four (4) screws securing
the foot stand. CAUTION: Hold the
stand firmly as you remove the last
screw.
Video
HDMI 1
HDMI 2
4
5
USB
ANALOG / DIGITAL
Repeat
Finish Setup
USB input jack is used to connect a USB mass storage
device to watch digital images stored in JPEG format.
ANTENNA IN
CABLE
If you are having problems, call us toll-free at 1-800-877-5032
Use the four (4) screws included in the
literature package (or removed from
the foot stand) to secure the HDTV to a
wall mounting kit.
DIGITAL AUDIO OUTPUT (Coaxial)
Hookup a multichannel receiver with the use of a phono-
type digital audio cable.
AV INPUT SELECTION
Press the INPUT key to select the
correct AV input for the video source
you wish to watch.
The tuner in this HDTV can receive:
IMPORTANT: Wall mount kit
must comply with VESA standard
200 x 200. All four (4) screws must
be threaded to the wall mount
and HDTV’s back cabinet
• Digital and Analog off air signals
from an antenna
Sanyo Manufacturing Corp. 3333
Sanyo Road, Forrest City, AR 72335
NOTE: Unused AV inputs may be dis-
abled with the Input Setting feature.
• Analog or ClearQAM cable channels
from a direct Cable TV connection.
Printed in Mexico, February 2013
US3C / 39-Z6SP / GXFA
Mounting screws measurements:
M6 (6mm) Diameter, Length—12mm
(maximum)
Need help?
1-800-877-5032
Need help?
1-800-877-5032
|