English
Français
Deutsch
Please note:
PRECAUTIONS
Your SANYO product is designed and
manufactured with high quality materials and
components which can be recycled and
reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from your
household waste.
■ In case of a problem
■ Protect from high temperatures
Do not use the unit if smoke or a strange odor comes from the unit,
or if it seems not to function correctly. Turn off the power
immediately and disconnect the power cord, and then consult your
dealer or an Authorized Sanyo Service Center.
Do not install close to stoves, or other heat sources, such as
spotlights, etc., or where it could be subject to direct sunlight, as this
could cause deformation, discoloration or other damage.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may rise to high levels.
INSTRUCTION MANUAL
VDC-C1575VP
VDC-D1585VP
VDC-W1595VP
■ Do not open or modify
COLOR CCD Camera
■ Cleaning
Please dispose of this equipment at your local
community waste collection/recycling centre.
In the European Union there are separate
collection systems for used electrical and
electronic products.
Do not open the cabinet, as it may be dangerous and cause
damage to the unit. For repairs, consult your dealer or an
Authorized Sanyo Service Center.
Dirt can be removed from the cabinet by wiping it with a soft cloth.
To remove stains, wipe with a soft cloth moistened with a soft
detergent solution and wrung dry, then dry by wiping with a soft
cloth.
Do not use benzine, thinner or other chemical products on the
cabinet, as this may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes
into contact with the cabinet for a long period of time, as this may
cause damage or paint peeling.
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
This instruction manual covers the following models. Any difference
among the three models is indicated when necessary.
VDC-C1575VP
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside
the unit. If used with a foreign object inside, it could cause a fire, a
short-circuit or damage. Be careful to protect the unit from rain, sea
water, etc. If water or liquid gets inside the unit, turn off the power
immediately and disconnect the power cord, and then consult your
dealer or an Authorized Sanyo Service Center.
Please help us to conserve the environment
we live in!
VDC-D1585VP
VDC-W1595VP
This symbol mark and recycle system
are applied only to EU countries and
not applied to countries in other areas
of the world.
Dimensions: mm (inches)
140.2 (5.5)
■ Be careful when handling the unit
To prevent damage, do not drop the unit or subject it to strong
shock or vibration.
■ Approvals: IP66
This unit has been certified to IP66 standards when properly
installed.
Ensure all openings in enclosure are sealed as per manufacturer's
instructions.
■ Do not install this unit close to magnetic fields
The magnetic fields may result in unstable operation.
■ Protect from humidity and dust
To prevent damage, do not install the unit where there is greasy
smoke or steam, where the humidity may get too high, or where
there is a lot of dust.
Depending on the conditions of use, installation and environment,
please be sure to make the appropriate settings and adjustments. If
you need help with installation and/or settings, please consult your
dealer or an Authorized Sanyo Service Center.
SANYO Electric Co., Ltd.
Printed in Korea
L5BN2/XE, XE2, XE3 (1106KP-CP-a)
TROUBLESHOOTING
SPECIFICATIONS
INSTALLATION
VDC-C1575VP
VDC-D1585VP
VDC-W1595VP
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, consult your
dealer or an Authorized Sanyo Service Center.
■ When routing the cables on ceiling or wall surfaces:
Loosen the conduit hole cover fixing screw (A) on the back of the camera
unit base with the hexagonal wrench (medium), open the cover (B), and
pass the connection cables through the conduit hole.
Scanning system
Image sensor
Number of effective
pixels
PAL standard 625 lines, 50 fields/sec.
(H)
1/3" interline transfer method CCD
752 (H) x 582 (V)
(G)
(H)
More than
(J)
■ If no image appears
Is the coaxial cable attached securely?
Horizontal resolution
More than 520 TV lines
0.05 lx
(I)
480 TV lines
1.0 lx (F1.4)
88.0
82.5
1
Loosen the four fixing screws (C) using the supplied hexagonal
wrench (large) and remove the dome cover (D).
(E)
Minimum illumination
(approx.)
(F1.4, B/W mode)
Are the power and voltage normal?
Has the iris of the lens been adjusted correctly (with the level
volume)?
1.0 lx (F1.4)
88.0
1.0 lx
(F)
2
3
4
Make screw holes and a cable hole in the rubber cushion (E).
Attach the rubber cushion to the back of the camera unit (F).
(F1.4, color mode)
Video output
Video S/N ratio
Lens
Pan/Tilt adjustment
Backlight compensation
Iris setting
White balance
Gain control
1.0 V(p-p) / 75 Ω, composite, BNC
More than 50 dB (AGC off)
Built-in vari-focal auto-iris, f = 2.6 - 6 mm, F = 1.4 - 2.0
Pan: ±180º, Tilt: ±60º (Ceiling Installed)
46.0
(A)
Is there adequate illumination?
Place the supplied "Mounting template" (G) on the mounting
surface, and mark four positions shown in (G).
■ If the image is unclear
Is the monitor adjusted correctly?
OFF / ON (Center zone metering)
AI / EI (Only AI is available for the built-in lens)
ATW / ATW-A ATW / ATW-A
ON / OFF
–
(M)
5
Drill holes at the positions as marked and insert the supplied
screw holds (H) in the holes.
(B)
(K)
Is the lens in focus?
(D)
6
7
Cut a hole in the ceiling or the wall for routing the cables.
Is the lens clean?
Wide dynamic range
Dynamic range
Sync system
–
–
–
–
ON / OFF
54 dB typical
Pass the power cable (I) and video cable (J) from the camera unit
through the cable hole in the ceiling or the wall.
Dirt or fingerprints on the lens can adversely affect the image.
Gently wipe any dirt or fingerprints off the lens with a soft cloth or
lens cleaning paper and cleaning fluid (commercially available).
DC 12 V user: Internal sync, AC 24 V user: Line-lock
(L)
Day/Night function
–
Always active
–
8
9
Align the unit mounting holes of the camera unit with the holes in
the ceiling or the wall.
(N)
-10 - +40°C
(14 - 104°F)
Temperature: -10 - +50°C (14 - 122°F)
Operating environment
Drop-prevention cord
Humidity: less than 90% RH (no condensation)
24 V AC ±10%, 50 Hz/12 - 15 V DC
Secure with the supplied mounting screws (K).
Power supply
Power consumption
(approx.)
(C)
10 Carry out the settings and adjustments for the camera. Refer to
“CONNECTIONS AND SETTINGS” for camera settings and lens
adjustments.
2.6 W
2.6 W
4.0 W
SERVICE
The camera is a precision instrument. Handle it carefully and
always follow the safety precautions. If the camera requires service,
never try to repair it yourself or open the casing.
Since the conduit hole cover is not waterproof-finished, always be sure to
seal the cover entirely by caulking, for example, upon completion of
installation.
Make sure to perform waterproofing properly to the ceiling or wall where
you are installing the unit.
When setting up this camera, make sure that it is installed securely.
Check that the installation location is strong enough to bear the camera
weight before proceeding. Install on a ceiling or wall that has no surface
unevenness. In addition, do not touch the camera unit except when
settings and adjustments are necessary.
Weight (approx.)
850 g (30 oz)
Hexagonal wrench, Large, Medium and Small ....... each1
Rubber cushion............................................................... 1
Mounting screw............................................................... 4
Screw hold ...................................................................... 4
Mounting template .......................................................... 1
11 If a whole surface of the lens does not show through the camera
window (L), loosen the screws (M) and adjust the dome liner (N).
And then secure the dome cover by tightening the fixing screws
(C) with the hexagonal wrench (large).
Accessories
For servicing, maintenance, or repairs, consult your dealer or an
Authorized Sanyo Service Center.
The factory setting value is represented in bold.
Appearance and specifications are subject to change without prior notice.
|