DC-MX30
INSTRUCTION MANUAL
MICRO Hi-Fi SYSTEM
IMPORTANT SAFETY INFORMATION
z
Keep this unit away from dripping or
z
Ensure the unit is plugged into an AC
splashing water. Ensure that no objects
filled with liquids, such as vases, are
placed on or near the unit.
230 - 240V 50 Hz power outlet. Using
the wrong type of power outlet might
damage the unit and even ca
z
z
To completely disconnect the power
input, the mains plug of apparatus shall
be disconnected from the mains.
Keep the unit away from strong
magnetic devices, heat sources and
direct light. Overheating will cause
damage and shorten the life of the
product.
use fire.
z
z
z
Danger of damage if battery is
incorrectly replaced. Replace only with
the same or equivalent type.
Before turning on the power for the first
time, make sure the power cord is
properly installed.
To reduce the risk of electric shock, do
not remove cover (or back), no user
serviceable parts inside; refer all
servicing to qualified service personnel.
Never let anyone, especially children,
push anything into holes, slots or any
other opening, as this could result in a
fatal electric shock.
z
z
Keep the unit away from dust, moisture
and water.
Don’t obstruct the ventilation vents on
the equipment, for example with
newspaper, table-cloths, curtains or soft
furnishings.
z
z
z
Minimum 10 cm distances around the
apparatus for sufficient ventilations.
Do not use strong chemicals, abrasives
or aerosol cleaners to clean the unit..
Store your tape or CD in a cool area to
avoid the damage from heat.
Do not use the unit in areas where
extremes in temperature occur (below 5
℃ or exceeding 35℃) or where it may
be exposed to direct sunlight.
z
z
z
Do not use the unit in areas where
humidity is too high, for example in
bathroom or in a wet basement and the
like. Use the unit in relativity humidity
45%~85%.
No naked flame sources such as lighted
Candles should be placed on the
apparatus.
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are
important operating and maintenance
instructions in the information
accompanying this unit.
You can see this carved picture on the
bottom of the main unit.
REMARK: In case of malfunction due to electrostatic discharge or fast transient (Burst), just reset
the product (reconnect of power source may be required) to resume normal operation.
2
CAUTION
CLASS 1 LASER PRODUCT
Operating the unit in a way other than specified herein, or
making adjustments to the unit may result in hazardous
radiation exposure
You can see the label on the
back of the unit
LASER SAFETY
This unit employs a laser. Only qualified service personnel should attempt repair.
You can see this
label in the CD
compartment.
WARNING: RISK OF INVISIBLE LASER RADIATION WHEN CD LID IS
OPEN OR INTERLOCKS FALL. AVOID DIRECT EXPOSURE TO THE
BEAM.
Note:
z
This unit will become warm when used for a long period of time. It’s a normal phenomenon.
Don’t worry about it.
z
This CD player includes microprocessors, which may malfunction as a result of external
electrical interference or noise. If the CD is not working properly, disconnect the power source
and then reconnect it.
z
z
In case of malfunction due to electrostatic discharge or fast transient（Burst）,reconnect of
power source may be required to resume normal operation.
Do not install this equipment in a confined space, such as a bookcase or built-in cabinet.
HEARING IMPORTANT NOTE
Your hearing is important to you and to us so please take care when operating this equipment. It is
strongly recommended that you follow the listed guidelines in order to prevent possible damage to,
or loss of hearing.
Establish a safety sound lever
Over time your hearing will adapt to continuous load sounds and will give the impression that the
volume has in fact been reduced. What seems normal to you may in fact be harmful. To guard
against this, set the initial volume of the equipment to a low level.
Once you have established a comfortable listening level do not increase the sound level further.
3
LOCATION OF CONTROLS AND FUNCTIONS
MAIN UNIT
1. Power Indicator
2. REMOTE Sensor
3. BASSXPANDER Indicator
4. DISPLAY
5. FM ST Indicator
6. +VOLUME- Control
7. TUNING Control
8. Dial Pointer
9.
PLAY / PAUSE Button
Button
10.
11.
Button
12. PROGRAM Button
13. PLAY MODE Button
14.
STOP Button
15. FOLDER+ Button
16. PHONES Socket
17. AUX IN Socket
18. FUNCTION Selector
(TAPE-OFF/CD/RADIO/AUX)
19. BAND Selector (AM/ FM/ FM ST)
20. BASSXPANDER
21. Cassette Door
22.
23.
24.
25.
26.
27.
PLAY Button
STOP/EJECT Button
RECORD Button
PAUSE Button
REWIND Button
F.FWD Button
28. Cassette Buttons Door
29. CD Door
30. CD Door OPEN Button
31. R+/R- Right Speaker Terminal
32. L+/L- Left Speaker Terminal
33. FM Antenna Wire
34. AC Cord
4
Remote Control
35.
36.
37.
38.
PLAY/ PAUSE Button
STOP Button
F.F. Button
F.R Button
39. PLAY MODE Button
40. FOLDER - Button
41. FOLDER + Button
42. PROGRAM
Note:
The distance between the remote control and the main unit should not be too far.
The remote control should be within approx. 7
meters at straight line to the REMOTE Sensor.
5
SETTING UP AND CONNECTING THE UNIT
Replacing battery of the remote control
1. Squeeze the notched tab A while pulling the battery door latch B
out to take the battery holder out.
2. Insert a “CR2025” 3V lithium battery. Make sure the polarity (the
+ and – side of the battery) is correct.
3. Replace the battery holder back in the remote control.
BATTERY PRECAUTIONS
Follow these precautions when using battery in this device..
1. Danger of explosion if battery is incorrectly replaced, use only the size and type of
battery specified.
2. Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
3. Be sure to follow the correct polarity when installing the battery as indicated in the
battery compartment. Reversed polarity may cause damage to the device.
4. If the device is not to be used for a long period of time, remove the battery to prevent
damage or injury from possible battery leakage.
5. Do not try to recharge battery, it is not intended to be recharged and doing so may
cause the battery to rupture or leak.
6. Do not dispose of batteries in general waste, contact your local Council regarding
available recycling or disposal options.
Speaker connection
To insert the speaker cable, push down the terminal lever of the RIGHT
Speaker Terminal and LEFT Speaker Terminal.
red
Please ensure the cables are connected into the speaker terminals with the
correct polarities. Connect the Left Speaker to the Left Speaker Terminals,
with red wire to the L+ and black wire to the L-.
Connect the Right Speaker to Right Speaker Terminals, with red wire to the
R+ and black wire to the R-.
black
Headphone connection
You can use headphones to listen in privacy. Insert the headphones 3.5mm plug into Phone Socket.
Use corresponding adaptors if you have different plugs, the speaker will cut off automatically when
the headphones are being used.
Note: Excessive sound pressure from earphones and headphones can cause hearing loss.
Mains connection
This unit was designed to operate at an AC 230 - 240V 50 Hz house current.
Connecting this system to any other power supply could result in damage to the unit, which is not
covered by your warranty. If this plug is not fit for your outlet, you should change your outlet by a
qualified licensed electrician.
6
1. Unwind the AC Power Cord completely.
2. Insert the plug into any convenient AC outlet.
3. As soon as the unit has been connected with the mains voltage, parts of the unit are in
operation due to the standby function. Turn off the unit completely before pulling the mains plug
out of the AC outlet.
AUX connection
1. Slide Function selector to AUX.
2. Connect a 3.5mm stereo jack lead to the AUX IN socket and the other end to your preferred
device.
3. Play your device.
BASIC OPERATION
Adjusting the sound volume
Turn the - volume + control to increase or decrease the sound level.
BASSXPANDER button
ON: Press the BASSXPANDER button once to active boost low frequency sound and the
BASSXPANDER indicator will light up.
OFF: Press once during ON mode and BASSXPANDER Indicator goes off.
RADIO OPERATION
1. Connect the power cord.
2. Slide the FUNCTION selector to RADIO position.
3. Slide the BAND selector to select the desired band. (AM/ FM/FM ST)
4. Turn the TUNING button to select the desired band.
5. Adjust + VOLUME – control to a comfortable sound level.
ANTENNA reception tips
FM: Extend and move the FM Antenna Wire. If stereo broadcast is received, the FM STEREO
indicator will light up. In case of Stereo stations with a bad reception (noise infested reception), we
recommend slide BAND selector to MONO position.
AM: This system is equipped with a built-in directional ferrite antenna,
move and rotate the system for best reception.
7
COMPACT DISC OPERATION
Notes when operating the CD disc
z
z
Only press the CD Door Open button to open the CD door.
To remove the disc, hold it by the edges and remove from the holder.
Loading Compact Disc
1. Slide the FUNCTION selector to CD position.
2. Press the OPEN button to open the CD door.
3. Place the disc into the tray with label side uppermost and push down to close
the CD door. The CD player will automatically scan the disc. The total
number of tracks will show in the display. For example, if the disc contains 17
tracks. The display will show as the figure on the right.
4. If there is no disc in the unit, the display will show “ NO”(refer to the figure on
the right).
Normal Playback
After loading a CD, press the
PLAY/PAUSE button on the main unit or on the remote control to
start playback. The track number will indicate in the display.
Pause control
To pause temporarily during CD playback, press the
PLAY/PAUSE button on the main unit or
PLAY/PAUSE button again to
on the remote control. The disc playback will pause. Press the
resume playback.
Skip track
During playback, press the
or
buttons on the main unit or press
F.F. or.
F.R Buttons on the remote control to skip to the previous or next tracks.
PLAY MODE CONTROL
There are three play modes. Press the PLAY MODE button once to active RPT mode, press the
PLAY MODE button twice to active RPT ALL mode, Press the PLAY MODE button third time to
active RDM mode, press the PLAY MODE button the fourth time to resume the normal playback.
Repeat a track
Select the track to be repeated and begin playback. Press the PLAY MODE button once. The RPT
indicator will show in the display and the selected track will be repeated continuously.
Repeat ALL
Press the PLAY MODE twice. The RPT ALL indicator will show in the display and all the tracks on
the disc will be repeated continuously.
Random playback
The random playback feature allows you play all the tracks on the current disc in a random
order. This function can be selected when the disc is playing or when in a stop mode. Press the
PLAY MODE button third times to random play mode. The RDM indicator is shown in the display.
8
If necessary, press the PLAY/PAUSE
select a track to play from the disc.
button to begin playback. The player will randomly
Note: In program mode, Random playback can’t be selected.
Clear play mode
Press the PLAY MODE button fourth times to cancel the play mode and normal playback will
resume.
Programmed Playback
It is possible to program a selection of up to 20 tracks for playback.
1. After loading a disc, Press the PROGRAM button in stop mode. PGM and
P01 will show in the display.
2. Press the
track number.
or
buttons repeatedly to select the desired
3. Press the PROGRAM button to confirm the first programmed track. P02
now shows in the display
4. Repeat steps 2 and 3 to store up to 20 tracks.
5. When programming is complete, press the
begin playback of the programmed tracks.
PLAY/PAUSE button to
Clear Program (Resume Normal Playback)
Press the STOP button twice during playback, or open the CD door, or change to another mode to
erase the programmed tracks.
MP3/WMA DISC OPERATION
Normal Playback
After loading a MP3/WMA, press
PLAY/PAUSE button to start playback. The MP3 or WMA
and current track number will indicate in the display.
Pause control
To pause temporarily during MP3 playback, press the
PLAY/PAUSE button. The disc playback
will pause. Press the
PLAY/PAUSE button again to resume playback.
Skip track
The procedure for skipping tracks is the same as previously described in the CD operation section
of this manual.
Skip ALBUM
In stop mode or during playback, press the FOLDER+ button repeatedly on the main unit or
FOLDER+ or FOLDER- buttons on the remote control to skip to next or previous folder, playback will
begin at the first track in the selected folder.
PLAY MODE CONTROL
There are four play modes. Press the PLAY MODE once to active RPT mode, press the PLAY
MODE twice to active RPT ALBUM mode, Press third time to active RPT ALL mode, press the PLAY
9
MODE button the fourth time to active RPT RDM mode, Press the PLAY MODE button fifth times to
resume the normal playback.
Repeat a track
Select the track to be repeated and begin playback. Press the PLAY MODE button once. The RPT
indicator will show in the display and the selected track will be repeated continuously.
Repeat ALBUM
Select the album to be repeated and begin playback. Press the PLAY MODE button twice. The
RPT and ALBUM will flash in the display and the selected album (folder) will be repeated
continuously.
Repeat ALL
Press the PLAY MODE third times. The RPT ALL indicator will show in the display and all the tracks
on the disc will be repeated continuously.
Random playback
The random playback feature allows you play all the tracks on the current disc in a random
order. This function can be selected when the disc is playing or when in a stop mode. Press the
PLAY MODE button fourth times to random play mode. The RDM indicator is shown in the display.
If necessary, press the PLAY/PAUSE button to begin playback. The player will randomly select
a track to play from the disc.
Note: In program mode, Random playback can’t be selected.
Clear Play mode
Press the PLAY MODE button fifth times to cancel the play mode and normal playback will resume.
Programmed Playback
It is possible to program a selection of up to 20 tracks for playback.
1. After loading a disc, Press the PROGRAM button in stop mode. PGM and P01 will show in the
display.
2. Press the FOLDER+ on the main unit or FOLDER+ or FOLDER - buttons on the remote control
to select desired ALBUM (FOLDER) and then Press the
repeatedly to select the desired track number.
or
buttons
3. Press the PROGRAM button to confirm the first programmed track. P02 now shows in the
display
4. Repeat steps 2 and 3 to store up to 20 tracks.
5. When programming is complete, press the
selected tracks.
PLAY/PAUSE button to begin playback of the
Clear Program (Resume Normal Playback)
Press the STOP button twice during playback, or open the CD door, or change to another mode to
erase the programmed tracks.
IMPORTANT NOTE FOR MP3/CD PLAYBACK CAPABILITY
Because of none-standardized format definition / production of MP3 / CD, playback quality &
performance are not guaranteed.
SANYO is not responsible for the playability of MP3 in any case due to recording conditions
such as PC performance, writing software, media ability and etc.
10
CASSETTE RECORDER OPERATION
Checking the Cassette
Make sure that the cassette tape has on slack before inserting it to cassette compartment. If the
tape slacks, the trouble may result when you play the tape, use a pencil as shown to take up slack
on one of the reels.(Refer to figure on the right.)
PLAYBACK
1. Slide FUNCTION selector to TAPE-OFF.
2. Open the CASSETTE BUTTON DOOR
3. Press the
button to open the cassette door. Insert a prerecorded cassette into the
cassette compartment with the exposed side uppermost and push the door to close the door.
4. Press the
button to start playback.
5. Press the
STOP/EJECT button to stop playing.
PAUSE control
To pause temporarily during tape playback, Press the
press the button again to resume playback
Fast Forward and REWIND
Press the F. FWD or
button. The disc playback will pause,
REWIND Buttons on the main unit to wind the tape backward quickly
or wind the tape forward quickly.
RECORDING
A) Recording from the radio
1. Slide the FUNCTION button to RADIO position.
2. Turn the TUNING button to select the desired band.
3.
Insert a blank tape with exposed side downwards and full spool to the left side into cassette
compartment and close cassette door.
4.
5.
Press the
Press the
RECORD button to start recording,
button to stop recording
B) Recording from the Compact Disc
1. Slide the FUNCTION button to CD position.
2. Load a CD and select the desired track.
11
3.
Insert a blank tape with exposed side downwards and full spool to the left side into cassette
compartment and close cassette door.
4.
5.
Press the
Press the
RECORD button to start recording
STOP/EJECT button to stop recording and the CD will be change to pause
mode, press the
button again to remove the cassette.
Note:
RECORD button to continue recording. Press the
STOP/EJECT
When the end of the tape was reached, the cassette deck will stop automatically even at
playback or recording mode.
Preventing accidental erasure
Whenever a recording is made, the sound previously recorded is erased automatically. To protect
valuable recordings from accidental erasure, the unit and cassette are equipped with standard
safety features. To keep the recorded material permanently, break out the tab on the back of the
cassette with a screwdriver
To protect side A, break out tab (1).
To protect side B, break out tab (2)
Note: A cassette with the erase guard tabs removed cannot be erased or used for recording and the
RECORD button cannot be pressed. To record on a cassette from which the cab has been
removed, simply attach adhesive tape over the tab opening.(3)
MAINTENANCE
Cleaning the unit
z
z
z
To prevent fire or shock hazard, disconnect your unit from the AC power source when
cleaning.
If the cabinet becomes dusty, wipe it with a soft dry dust cloth. Do not use any wax or polish
sprays on the cabinet.
If the cabinet becomes dirty or smudged with fingerprints it may be cleaned with a soft cloth
slightly dampened with a mild soap and water solution. Never use abrasive cloths or polishes,
as these will mar the finish of your unit.
Caution: Never allow any water or other liquids to get inside the unit while cleaning.
12
Compact Discs Maintenance
z
Treat the disc carefully. Handle the disc only by its edge. Never allow your fingers to contact
with the shiny, unprinted side of the disc.
z
z
Do not attach adhesive tape, stickers etc., to the disc label.
Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents or adhesive
cleaners to clean the disc. If necessary, use a CD cleaning kit.
z
z
z
z
If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged
(scratched).
When cleaning the disc, wipe in straight lines from the center of the disc to the edge of the
disc. Never wipe in circular motions.
To remove a disc from its storage case, press down on the center of the case and lift the disc
out, holding it carefully by the edges.
Fingerprints and dust should be carefully wiped off the disc’s recorded surface with a soft
cloth. Unlike conventional records, compact discs have no groove to collect dust and
microscopic debris, so gently wiping with a piece of soft cloth should remove most particle.
Cleaning the tape heads
When dust or reddish-brown oxide has accumulated on the tape deck heads, pinch roller and
capstan. Failure to clean these parts can result in inferior quality of sound, distortion of recorded
sound, deterioration of high frequency sound reproduction and inconsistent tape speed.
To ensure playback and recording with good quality sound, use a cleaning tape (available from your
local audio dealer) to clean the head block of the deck after about every 10 hours of use.
1. Open the cassette compartment lid by pressing
STOP/EJECT button.
2.
Moisten a cotton bud with isopropyl alcohol or special head cleaning fluid. Gently rub the face
of PLAY and RECORD head and erase head. Also clean the capstan and pinch roller.
13
TROUBLESHOOTING GUIDE
If you experience any difficulties in operating this unit, please take the time to read the hints and tips
shown in the troubleshooting guide below.
Symptom
Possible cause
Solution
Radio
No signal from the Radio
Unit is not in Radio mode
Slide the FUNCTION selector to
Radio mode
Noise or sound distorted on AM Station is not tuned properly for Retune the AM or FM broadcast
or FM broadcasting
AM or FM
station
FM: Wire antenna is not
extended enough
AM: Unit is not positioned
correctly
Extend FM wire antenna
Reposition the unit until the best
reception is obtained
FM STEREO indicator does not FM signal not enough strong or Extend antenna or find another
light
the station is not in stereo
broadcasting
FM stereo station
AM or FM no sound
Unit not at TUNER function AM Slide the BAND selector to
or FM band
select AM or FM band
Volume at minimum
Increase the volume level
CD/MP3 Player
CD Player doesn’t play
Unit not in CD mode
Slide the FUNCION selector to
CD mode
CD is not installed or installed
incorrectly
Load a CD; check that the CD is
placed in the tray with the label
side uppermost
Disc is non-standard
Disc is not compatible with
format
Use correct disc
Change compatible CD format
CD skips while playing
Disc is dirty or scratched
Wipe disc with soft dry cloth or
use another disc
Cassette Recorder
No sound
Function selector is not at
RADIO mode.
Slide the Function selector to
Radio
Volume at minimum
Head is dirty
Increase Volume
Clean the head
Sound distorted
Speed varies
Tape old or worn
Replace the tape
Clean roller and capstan
Dirty roller and capstan
Can’t be recorded
Record protection tab removed Attach adhesive tape over the
tab opening
Defective tape or dirty tape head Replace tape or clean tape
head
Distorted sound on playback
14
SPECIFICATIONS
Radio Section
Frequency Range --------------------------------
AM (Built-in ferrite bar): 530 – 1600 KHz
FM (wire antenna): 88 – 108 MHz
CD / MP3 Player
Playback System --------------------------------
Memory Program --------------------------------
Laser Output (Maximum) ------------------------
Wavelength---------------------------------
Cassette Recorder
Top load CD mechanism
20 Tracks
5 mW
790 土 30 nM
Recording System -------------------------------
Erase System -------------------------------------
Audio Section
DC Bias
Magnet Erase
Power Output -------------------------------------
Headphone Impedance ------------------------
Speaker System
2 Watts RMS X 2
8 – 32 ohm
Impedance------------------------------------------
Driver -----------------------------------------------
General
4 ohm
3 inch full range
Power Source ------------------------------------
AC 230 - 240V 50Hz
DC 3V - 1 pc of “CR2025” lithium battery (included)
or equivalent for remote handset
23 Watts
Power Consumption ----------------------------
Dimension (mm)------------------------------------
Main Unit
: 155(W) x 224(H) x 211.5(D)
Speaker Box : 119(W) x224(H) x 153(D) (approx)
Net Weight------------------------------------------------- 4 kg
ACCESSORIES:
Instruction Manual
----------------------------
1 pc
1 pc
Remote Control Handset --------------------
15
CODE NO: 172-G401043010-OSY
SANYO Electric Co., Ltd.
Made in China
|