SIIG Computer Hardware 04 0444A User Manual

Hi-Speed USB 5-Port PCI  
Quick Installation Guide  
FeaturesandBenefits  
Compliant with USB specifications revision 2.0  
Conforms to PCI specifications revision 2.2  
Supports simultaneous operation of multiple  
high-speed USB 2.0 and USB 1.1 devices  
Supports high-speed (480 Mbps), full-speed (12  
Mbps), and low-speed (1.5 Mbps) data transfer  
modes  
User friendly hot-swapping feature allows you to  
attach/removeUSBdeviceswithouturningoffyour  
system  
Note: USB 1.1 devices are limited to USB 1.1 speeds  
evenwhentheyareconnectedtoUSB2.0hostadapter  
or USB 2.0 hubs.  
SystemRequirements  
PC:  
Pentium-class computer with an available PCI slot  
Windows 2000 SP4 or later/XP SP1 or later/  
Server 2003/Vista  
Mac:  
Power Mac G3 (blue & white) or later with an  
available PCI slot  
Mac OS 10.2.8 or later  
04-0444A  
 
1
USBPin-outHeader  
The USB pin-out header consists of 4 pins and allows for  
1 USB connection.  
Important: The internal USB port and the USB Pin-out  
Header can not be used at the same time. Do not connect  
devices to both ports at the same time.  
Black  
Green  
GND  
White  
DATA +  
Red  
DATA -  
VCC/+ 5VDC  
Figure 2. USB Pin-out Header  
Hardware Installation  
General instructions for installing the card are provided  
below. Since the design of computer cases and  
motherboards vary, refer to your computer’s reference  
manual for further information, if needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computer's case for a few  
seconds. Avoid any contact with internal parts and  
handle card only by their external edges.  
1. Turn OFF the power to your computer and any  
other connected peripheral devices.  
2. Unplugthepowercordandremoveyourcomputer's  
cover.  
3. Remove the slot bracket from an available PCI slot.  
3
 
4. Carefully align the card to the selected PCI slot,  
push the board down firmly, but gently, until it is  
well seated.  
5. Replace the slot bracket's holding screw to secure  
the card.  
6. Replacethecomputercoverandreconnectthepower  
cord.  
Windows Driver Installation  
The Hi-Speed USB 5-Port PCI has three built-in USB hosts.  
Two hosts handle USB 1.1 devices and the third host  
handles USB 2.0 devices. USB 1.1 and USB 2.0 devices are  
automatically routed to the correct USB hosts.  
WindowsDriverInstallation  
Windows 2000 Service Pack 4 or later, Windows XP  
Service Pack 1 or later, Windows 2003 Server, and Vista  
have built-in driver support for this controller. Just  
install the board and Windows will automatically detect  
and install the correct drivers for it. No additional driver  
is necessary.  
ToVerifyWindowsInstallation  
Right click My Computer. Click Manage, then click  
Device Manager.  
Under Universal Serial Bus controllers:  
- NEC PCI to USB Open Host Controller  
- NEC PCI to USB Open Host Controller  
- Standard Enhanced PCI to USB Host Controller  
- USB Root Hub (USB 2.0 Root Hub in Win2K)  
- USB Root Hub  
- USB Root Hub  
4
 
Mac OS Driver Installation  
Mac OS has built-in driver support for this controller.  
Just install the board and Mac OS will automatically  
detect and install the correct drivers for it. No additional  
driver is necessary.  
To Verify Mac OS Driver Installation  
Mac OS X (v10.2.8)  
The only way to verify the board works is actually  
connecting devices to the USB ports.  
Mac OS X (v10.3.0) or later  
Check System Profiler to verify successfull installation.  
Click Go, then Utilities. Double click on System Profiler  
Under USB  
- USB High-Speed Bus  
- USB Bus  
- USB Bus  
5
 
Blank Page  
6
 
Technical Support and Warranty  
QUESTIONS?  
SIIG’s Online Support has answers!  
Simply visit our website at www.siig.com and click on Support.  
Our online support database is updated daily with new drivers  
and solutions. Answers to your questions could be just a few clicks  
away. Youcanalsosubmitquestionsonlineandoneofourtechnical  
support analysts will promptly respond.  
Thisproductcomeswithalifetimemanufacturerwarranty. Pleasesee  
SIIGwebsiteformorewarrantydetails. Ifyoushouldhappentohave  
any problems with this product, follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective,anRMAnumberwillbeissued. SIIGRMAdepartment  
can also be reached at (510)413-5333.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
7
 
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel  
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),  
Networking,SoundCards,andotheraccessories. SIIGisthepremier  
one-stop source of upgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
foundincomputerretailstores,mailordercatalogs,ande-commerce  
sitesintheAmericasandtheUK,aswellasthroughmajordistributors,  
system integrators, and VARs.  
PRODUCT NAME  
Hi-Speed USB 5-Port PCI  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Ave.  
Fremont, CA 94538-3152  
Hi-SpeedUSB 5-PortPCIisatrademarkofSIIG,Inc.  
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are  
registered trademarks of Microsoft Corporation. Mac and Mac OS are registered trademarks of  
AppleCorporation. PentiumisaregisteredtrademarkofIntelCorporation. Othernamesusedin  
publicationareforidentificationonlyandmaybetrademarksoftheirrespectivecompanies.  
December, 2006  
Copyright ©2006 by SIIG, Inc. All rights reserved.  
 

Sharp CD Player CD DD4500 User Manual
Soleus Air Air Conditioner air condition User Manual
Sony Car Stereo System XR M510 User Manual
Sony DVR DCR IP5 IP7BT User Manual
Sony Ericsson Cell Phone MT15a User Manual
Sony Headphones MDR EX85LP BLK User Manual
Sony Home Security System BRCSDP12 User Manual
StarTechcom Switch SV565USAGB User Manual
Subaru Robin Power Products Portable Generator RGX2400 User Manual
Sylvania TV DVD Combo 6513DD 6519DD User Manual