Model S5832SG
Control Panel
8 to 32 Zones
Installation
Instructions
Table of Contents
Compliance and Regulatory Information ....................i
Programming the Panel ........................................ 8 - 10
Remote Programming (RPS)........................................ 8
Direct Connect ............................................................. 8
Keypad Activated RPS......................................... 8 - 9
Programming With an LED Keypad ............................ 9
Programming With an Alphanumeric Keypad ........ 10
Quick Programming Mode ...................................... 10
Menu Programming Mode ...................................... 10
Programming With an Icon Keypad .......................... 10
Installing and Connecting the Control Panel ..... 1 - 5
Sierra S5832SG PC Board Layout.............................. 1
Mounting the Panel.................................................. 1 - 2
Panel Setup and Installation ....................................... 1
Earth Ground ............................................................... 1
Mounting the Enclosures .............................................. 2
S5832S Enclosure (Small) ....................................... 2
S5832 Enclosure (Large) .......................................... 2
Backup Battery ................................................................ 3
Sierra Accessory Loading ............................................ 3
AH Requirements for Backup ...................................... 3
Determining Standby Battery Requirements ........ 3
AC Power ......................................................................... 3
Output Terminals ............................................................ 4
External Bell Supervision ............................................. 4
Keypad Wiring ................................................................ 4
Sierra Accessory Wiring Distances ......................... 4
Keypad Addressing .................................................... 5
Connecting an Auxiliary Keypad (J8) .................... 5
Zone Terminals ............................................................... 5
On-Board Relay Terminals (TB2) ................................ 5
Installer Mode Options, (Block 0) ..................... 11 - 12
Installer Walk-Test ........................................................ 11
Event Memory ............................................................... 11
Event Memory Codes...............................................11
Custom Messages ........................................................ 12
Test Report ..................................................................... 12
Test Report with Audibles ........................................... 12
Audible Test ................................................................... 12
Entry Delay Test ............................................................ 12
Exit Delay Test .............................................................. 12
Transmit Walk-Test Queue Reports .......................... 12
RPS Callback ................................................................ 12
Battery Test .................................................................... 12
Accessories .............................................................. 5 - 7
S5050 Relay/Event Memory Module.................... 5 - 6
Switch Settings............................................................ 6
Switch Configuration ................................................. 6
S5058 Zone Expansion Module.................................. 6
ZEM Addressing .......................................................... 6
SN915-BUS SpreadNet Receiver ............................... 7
SN990/991 SpreadNet Keypad/Remote ................... 7
SN961 SpreadNet Keyfob ............................................ 7
Programming Summary ...................................... 13 - 39
Block 1: Code Option Programming ............... 13 - 14
Block 2: Zone Configuration Programming ... 14 - 16
Block 3: Armed System Programming ............ 16 - 21
Block 4: Digital Communicator Programming 21 - 25
Block 5: Reporting Digits Programming ......... 25 - 29
Block 6: Real Time Clock Programming ................. 30
Block 7: Auxiliary Devices Programming....... 31 - 34
Block 8: SpreadNet Programming ............................ 35
Block 9: Partition (Area) Programming .......... 35 - 37
Block 10: User Code Programming ................ 37 - 39
Digital Communicator ............................................. 7 - 8
Removing/Installing the Digital Communicator ....... 7
Digital Communicator Terminal Connections..... 7 - 8
Terminal Connections ................................................... 8
Standby Battery Information
Country Specific Compliance Information
Singapore
The Table and worksheet below provide the installer with the infor-
mation necessary to determine the AH rating and battery require-
ments for any particular installation.
The following hardware and programming guidelines are required
for installation of this system in Singapore.
Sierra Accessory Loading
Product current consumption
Max. Standby
Max. Active
125 mA
50 mA
Hardware Requirements:
S5832 Control Panel
125 mA
1. The Digital Communicator must be Model S5070SG or S5070SG-2.
S5010 Alpha Keypad
S5020 LED Keypad
30 mA
30 mA
50 mA
S5030 Icon Keypad
30 mA
50 mA
Programming Requirements:
S5050 REMM (up to 2)
S5058 ZEM (up to 3)
S5070 Single-line Dialer
S5070-2 Dual-line Dialer
SN915-BUS RF Receiver
100 mA (each)
40 mA (each)
35 mA
100 mA
40 mA**
60 mA
1. Dial Type (Block 4, CL 101) must be programmed for DTMF only.
2. Dial Attempts (Block 4, CL 102) must not be programmed to more
than 10.
35 mA
70 mA
125 mA
170 mA
**ZEM VOUT terminals can supply up to 300 mA (max.)
Malaysia
Table A - Standby Battery Loading
The following hardware and programming guidelines are required
for installation of this system in Malaysia.
AH Requirements for Backup
Hardware Requirements:
Product/Device
S5832SG
S5010
4-Hour
0.5 AH
0.12 AH
0.12 AH
0.12 AH
0.4 AH
0.16 AH
0.14 AH
0.5 AH
0.04 AH
0.1 AH
24-Hour
3.0 AH
0.72 AH
0.72 AH
0.72 AH
2.4 AH
72-Hour
9.0 AH
Qty Total
1. The Digital Communicator must be Model S5070SG or S5070SG-2.
2.16 AH
2.16 AH
2.16 AH
7.2 AH
S5020
Programming Requirements:
S5030
S5050
1. Dial Attempts (Block 4, CL 102) must not be programmed to more
than 3.
S5058
0.96 AH
0.84 AH
3.0 AH
2.88 AH
2.52 AH
9.0 AH
S5070(-2)
SN915-BUS
Sensor (10 mA)
Sensor (25 mA)
0.24 AH
0.6 AH
0.72 AH
1.8 AH
Bell/Siren (5 min) 0.085 AH
Bell/Siren (15 min) 0.225 AH
0.085 AH
0.225 AH
0.085 AH
0.225 AH
* Bell/Siren current may be 0.7 - 1.0 A
Total AH Required
Table B - AH Requirements
Determining Standby Battery Requirements
To calculate the size (AH rating) of your system's Backup Battery,
enter the Number (Qty) of devices of each type in the chart above.
Multiply the number of devices times the AH rating for the desired
backup period (Qty x AH = Total) and enter the total in the last
column. To determine the total AH rating of the battery, add all
values in the last column.
Total current from all sensors must be considered when calculat-
ing AH rating. For example:
10 sensors @ 10 mA = 100 mA
4 sensors @ 25 mA = 100 mA
Total current all sensors = 200 mA
i
S5832SG Terminal Layout
Nylon retaining
screw
Figure 1
S5832SG PCB Terminal Layout
Panel Setup and Installation
Introduction
This manual contains basic information and program-
ming information for the Sierra Model S5832SG con-
trol panel.
The first step in any installation process is careful planning
of the installation. Install the Sierra Model S5832SG in a
location as close as possible to power and phone lines. The
control panel is designed to operate as a local panel, with an
optional plug-on digital communicator.
For additional information regarding programming and
applications, refer to the Expanded Programming sec-
tion of the S5090 Sierra Reference Manual.
EarthGround
To ensure the effectiveness of the lightning and transient
protection circuits, the control panel must be connected to
"Earth Ground". Ideally, this should be a common ground to
the power lines, telephone system, and security system.
This type of ground, called a "Unified Earth Ground", pro-
vides the best protection. The ground connection, from a
grounding rod, cold water pipe or other established ground
point, is made to the green/yellow jacketed wire, providing a
ground to the panel housing.
Mounting the Panel
The Sierra S5832SG should be mounted in a location
which allows convenient access to AC power, tele-
phone connections, and earth ground (see Figure 2).
•
•
Remove the knock-outs, if necessary.
Mark the screw mounting holes on the wall, using
the cabinet as a template.
•
•
Mount the cabinet at the desired height and pass
the cables through the knock-outs.
Power
Lines
Telephone
Lines
Mount the circuit board to the stand-offs. The stand-
offs are factory installed. The metal stand-off (lower
left corner) has a panhead screw to be used for con-
necting earth ground.
Control
Panel
Power Line
Earth Ground
Telephone
Earth Ground
•
Connect the earth ground wire (green with yellow
stripe) to the board (see Figure 1) and cabinet. The
earth ground wire will connect to the upper hinge
when using the large enclosure and to the lower
hinge on the small enclosure.
Figure 2
Connecting to
Earth Ground
Unified Earth Ground
with Bonded Ground Roots
1
Housing Mounting Holes
Housing Mounting Holes
Wiring Knock-outs
Wiring Knock-outs
Figure 3 (a)
Mounting the S5832S
Enclosure
266 mm
10.5"
Wiring Knock-outs
Top
PCB Mounting
Hardware
(see page 1
for details)
Housing
Mounting Holes
Wiring Knock-outs
Left side
Wiring Knock-outs
Right side
Housing Mounting Holes
Wiring Knock-outs
Bottom
Figure 3 (b)
Mounting the S5832
Enclosure
2
Backup Battery
AH Requirements for Backup
The system employs one or more 6.5 AH (Model 1265) or 7.0
AH (Model 1270) sealed lead-acid storage battery. Connect
the battery to the control panel PCB via the red (+) and black
(-) leads. The battery should be replaced every 3 - 5 years.
Product/Device
S5832SG
4-Hour
0.5 AH
24-Hour
3.0 AH
72-Hour
9.0 AH
Qty.
Total
S5010
S5020
S5030
S5050
0.12 AH
0.12 AH
0.12 AH
0.4 AH
0.72 AH
0.72 AH
0.72 AH
2.4 AH
2.16 AH
2.16 AH
2.16 AH
7.2 AH
When connecting two or more batteries in parallel, use the
Model S5054 Auxiliary Battery Harness. Both batteries must
have the same AH (Ampere-Hour) rating and should have
the same lot number or date code. Figure 4, below, shows
correct method for wiring the batteries in parallel.
S5058
0.16 AH
0.14 AH
0.5 AH
0.04 AH
0.1 AH
0.96 AH
0.84 AH
3.0 AH
0.24 AH
0.6 AH
2.88 AH
2.52 AH
9.0 AH
0.72 AH
1.8 AH
S5070 (-2)
SN915-BUS
Sensor (10 mA)
Sensor (25 mA)
Bell/Siren (5 min)
NOTE: Up to 2 batteries may be connected in parallel to
obtain the desired standby (backup) time.
0.085 AH 0.085 AH 0.085 AH
Bell/Siren (15 min) 0.225 AH 0.225 AH 0.225 AH
* Bell/Siren current may be 0.7 – 1.0 A
Total AH Required
Self-resetting
circuit
Table 2 - AH Requirements
To S5053 LSM
or S5832SG
Control Panel
Determining Standby Battery Requirements
To calculate the size (AH rating) of your system's Backup
Battery, enter the Number (Qty) of devices of each type in
the chart above. Multiply the number of devices times the
AH rating for the desired backup period (Qty x AH = Total)
and enter the total in the last column. To determine the
total AH rating of the battery, add all values in the last
column.
C & K Model
1265 or 1270
C & K Model
1265 or 1270
Figure 4
Connecting two Batteries in Parallel
Total current from all sensors must be considered when
calculating AH rating. For example:
10 sensors @ 10 mA = 100 mA
Sierra Accessory Loading
Product Current Consumption
S5832SG Control Panel
S5010 Alpha Keypad
S5020 Icon Keypad
Max. Standby
125 mA
Max. Active
125 mA
50 mA
4 sensors @ 25 mA = 100 mA
Total current all sensors = 200 mA
30 mA
30 mA
50 mA
S5030 LED Keypad
30 mA
100 mA (each)
50 mA
100 mA
AC Power
S5050 REMM (up to 2)
(Relay/Event Memory Module)
S5058 ZEM (up to 3)
(Zone Expansion Module)
S5070 Single-line Digital
Communicator
S5070-2 Dual-line Digital
Communicator
SN915-BUS RF Receiver
The Sierra S5832SG receives its power from a 16.5 VAC 40
VA transformer. Connect the transformer to the AC In termi-
nals on TB1 of the PCB (see Figure 1), using 18 AWG (1.02
mm) wire. (Some systems may have the transformer and
mains fuse block installed and pre-wired from the factory.)
40 mA (each)
35 mA
40 mA**
60 mA
35 mA
70 mA
Connect the AC transformer to an unswitched receptacle.
Do not share the secondary of the transformer with other
devices.
125 mA
170 mA
** ZEM VOUT Terminals can supply up to 300 mA (max.)
NOTE: AC input requirements may vary by country. Refer to
the Compliance section for additional wiring information.
Table 1 - Standby Battery Loading
Table 1 shows the current requirements for the Sierra
S5832SG control panel and accessories. Additional infor-
mation about Standby Battery requirements and Audible
times may be found in Table 2 - AH Requirements, at the top
of the next column.
3
Keypad Wiring (cont.)
Output Terminals
Figure 6, below, shows the connections for wiring the Sierra
Keypad to the Control Panel and connecting the optional
Terminate Exit Delay switch. Switch S1, in the lower right-
hand corner, is used for keypad addressing (see Table 5).
Table 3 shows the Output Terminals of the S5832SG, with
the Voltage and Current Range of each Output. The Table
also shows the maximum combined current for related out-
puts.
NOTE: If the keypad tampers are active (and programmed
in Block 3, Cmd Loc 044 - 045), tamper signals will be sent
to the control panel via the keypad bus. Keypad tamper
(hardwired keypads only) report routing is programmed in
Block 4, Cmd Loc 158. Keypad trouble conditions are also
reported on the keypad bus and the routing is defined in
Block 4, Cmd Loc 159.
Voltage
Range
Combined
Current
Function Terminal
Current
Comments
Specifically designed to
drive strobes with high
in-rush currents.
Typically used to drive
sirens mounted inside
the premises.
Supervised Siren Output
typically used to drive
bells, sirens, and other
high current devices
outside the premises.
Strobe
STROBE
Output
8.4 – 14.9 V
0.75 A
Internal
Siren
INT
SIREN
8.4 – 14.9 V
0.75 A
2.0 A
External
Siren
BELL+
BELL-
8.4 – 14.9 V
1.5 A
(3.0 A with
Battery)
Auxiliary
Power
Used to drive sensors,
etc.
AUX
8.4 – 14.9 V
8.4 – 14.9 V
1.0 A
0.3 A
Used to drive latching
devices like glassbreak
detectors or four-wire
smoke detectors that
must be reset.
Switched
Auxiliary
Power
SW AUX
Used to power keypads,
REMMs, ZEMs, and
SN915 RF Receiver.
Keypad
Power
KPWR
Z8
8.4 – 14.9 V
8.5 – 14.0 V
1.0 A
Optional Terminate
Exit Delay Switch
Zone 8
0.03 A
0.03 A
2-wire Smoke Detectors
Table 3
Output Terminal limits
Tamper Switch
External Bell Supervision
The circuit connection shown in Figure 5 is used only when
External Bell Line Super-
vision is required. For Bell
Line Supervision, the bell
must be equipped with an
internal diode.
9.X 2.2K Ohm
Figure 6
Connecting the Keypad Terminals
EOL
Sierra Accessory Wiring Distances
The Table shown below shows the maximum wiring dis-
tances for the Sierra accessories based upon total load cur-
rent drawn from each run. Refer to the Accessory Loading
Table on page 3 for load requirements.
To Bell Output Terminals
on Control Panel
Figure 5 - Bell Supervision Wiring
NOTE: Total wire distance for all devices combined not to
exceed 2440 M.
Keypad Wiring
Max Load 0.40 mm
0.51 mm
(24 AWG)
0.64 mm
(22 AWG)
0.81 mm
(20 AWG)
1.02 mm
(18 AWG)
1.29 mm
(16 AWG)
The Sierra S5832SG uses four terminals for powering and
communicating with the keypads and other devices via the
keypad data bus. The terminal connections are as follows:
per run
(mA)
(26 AWG)
(Ft.)
M
M
(Ft.)
M
(Ft.)
M
(Ft.)
M
(Ft.)
M
(Ft.)
50
100
150
200
250
300
350
400
450
500
550
600
700
800
900
1000
121 (395) 192 (629)
60 (198) 96 (314)
40 (132) 64 (210)
305 (1000) 490 (1605) 774 (2538) 1225 (4016)
153 (500) 245 (803) 387 (1269) 612 (2008)
102 (333) 163 (535) 258 (846) 408 (1339)
76 (250) 122 (401) 194 (635) 306 (1004)
61 (200) 98 (321) 155 (508) 245 (803)
51 (167) 82 (268) 129 (423) 204 (669)
44 (143) 70 (229) 111 (363) 175 (574)
38 (125) 61 (201) 97 (317) 153 (502)
34 (111) 54 (178) 86 (282) 136 (446)
31 (100) 49 (161) 77 (254) 122 (402)
KPWR This terminal supplies +12 VDC to power the key-
pads or accessories.
KY+ One half of the differential keypad data bus. This
terminal combined with the KY- terminal provides
communication between the various devices and
the control panel.
30 (99)
24 (79)
20 (66)
17 (56)
15 (49)
13 (44)
12 (40)
11 (36)
10 (33)
48 (157)
38 (126)
32 (105)
27 (90)
24 (79)
21 (70)
19 (63)
17 (57)
16 (52)
14 (45)
12 (39)
10 (35)
KY-
Used in conjunction with the KY+ terminal for data
communications on the keypad data bus.
Common (ground) terminal for Power return.
28 (91)
25 (83)
22 (71)
19 (63)
17 (55)
15 (50)
45 (146) 70 (231) 111 (365)
41 (134) 65 (212) 102 (335)
35 (115) 55 (181) 87 (287)
31 (100) 48 (159) 77 (251)
C
9
8
6
6
(28)
(25)
(22)
(20)
TRMX Optional Terminate Exit Delay switch connected
between this terminal and C terminal. When active
(Block 7, CL 012), closing the exit delay switch will
short the TRMX terminal and skip all but the last 5
seconds of the exit delay.
27 (89)
24 (80)
43 (141) 68 (223)
39 (127) 61 (201)
9
(31)
Table 4
Maximum Wiring Distance for Sierra Accessories
4
The N.O. and N.C. zone configurations do not provide for
supervision of the detection devices.
Keypad Addressing
The S5832SG control panel will support up to 16 hardwired
keypads. Each keypad must have a different address, with
addresses ranging from 1 - 16. (Figure 6 shows the location
of the switch used to address the keypad.) Table 5 lists the
switch settings for S1 for each keypad address.
The following configurations provide supervision of the de-
tection devices:
EOL: This zone configuration uses a single EOL resistor to
detect the following conditions: Normal (2.2K), Fault (open
or short).
Addr
A0
on
off
on
off
on
off
on
off
A1
off
on
on
off
off
on
on
off
A2
off
off
off
on
on
on
on
off
A3
off
off
off
off
off
off
off
on
Addr
9
A0
on
off
on
off
on
off
on
off
A1
off
on
on
off
off
on
on
off
A2
off
off
off
on
on
on
on
off
A3
on
on
on
on
on
on
on
off
1
2
3
4
5
6
7
8
Supervised EOL: This zone configuration uses a single EOL
resistor to detect the following conditions: Normal (2.2K), Fault
(short), or Trouble (open).
10
11
12
13
14
15
16
Tamper: This zone configuration uses two EOL resistors to
detect four different zone conditions: Normal (2.2K), Fault
(4.4K), Trouble (short), or Tamper (open).
NOTE: For devices requiring a 10K Ohm EOL resistor,
use Zone 7 and remove jumper J5. (See page 1, Figure
1 for jumper location.)
Table 5
Keypad Addressing
Each keypad (Alphanumeric, Icon, or LED) may draw up to
50 mA of current. Once connected, the control panel will
automatically recognize the presence of the keypad.
On-Board Relay Terminals (TB2)
The Sierra S5832EB has a single-pole, double-throw (Form
C) relay mounted on the PCB. Connections to the relay are
made at TB2. (Refer to Figure 1 for relay terminal location.)
Connecting an Auxiliary Keypad (J8)
The S5832SG Control Panel also has a 4-pin Molex® con-
nector (J8) for attaching an auxiliary keypad to the panel for
on-site programming. The connector (J8) is located on the
PCB above the Keypad Data Bus terminals (see Figure 6,
on page 4).
The on-board relay may be configured as Normally Open
(N.O.) or Normally Closed (N.C.) and can switch up to 1 A of
current at 12 VDC. For programming options, refer to Block 7,
Command Location (CL) 001.
The connections to J8 are as follows:
Accessories
Pin 1 Common (ground) for Power return.
Pin 2 Supplies +12 VDC to power the keypad.
Pin 3 KY+ on the differential keypad data bus.
Pin 4 KY– on the differential keypad data bus.
The Sierra S5832SG supports a variety of accessories which
communicate with the panel through the keypad data bus.
These accessories can include up to two Model S5050 Re-
lay/Event Memory Modules (REMM), up to three Model
S5058 Zone Expansion Modules (ZEM), and a Model SN915-
BUS SpreadNet® RF Receiver.
Pins 1 and 2 supply power and ground, while pins 3 and 4
provide communication between the panel and the keypad.
Caution: When connecting accessories to the system,
use care not to exceed rated outputs. (See Table 1
on page 3 for Accessory loading information.)
Zone Terminals
The basic configuration of the S5832SG can support up
to 8 hardwired zones. Zone 8 is a powered loop for use
with two-wire smoke detectors. This loop is current-lim-
ited at 30 mA.
S5050 Relay/Event Memory Module
The Sierra S5832SG control panel will support up to two
Model S5050 REMMs connected to the keypad data bus.
NOTE: Trouble conditions and tampers, if enabled, are re-
ported via the keypad bus. Refer to Block 4, CL 158 and
159, respectively, for report routing information.
Power for the S5050 REMM is obtained by connecting the
KPWR terminal on the REMM PCB to either the KPWR or
AUX terminal on the control panel. For the power return,
connect the C terminal on the REMM to the C terminal on
the control panel. The GND terminal on the REMM PCB is
used to connect the REMM to Earth Ground.
c) EOL
End-of-Line
Resistor
d) EOL,
Supervised
e) 2x EOL
4-state
supervision
a) N.O.
Normally
Open
b) N.C.
Normally
Closed
Figure 7
Zone Configurations
Adding one REMM will increase Event Memory storage ca-
pability from 60 events to 250 events. Adding a second
REMM will increase the storage capacity to 500 events.
Zones may be configured with Normally Open (N.O.) or Nor-
mally Closed (N.C.) contacts (although not recommended).
5
The REMM also has five independently programmable re-
lays. The relay programming options are explained in the
programming summary, Block 7.
S5058 Zone Expansion Module
The Sierra S5832SG control panel has eight hardwired
zones and may be expanded up to 32 zones. Eight addi-
tional hardwire zones are obtained by connecting an
S5058 Zone Expansion Module to the keypad data bus.
Up to three S5058 ZEMs may be connected, providing a
total of 24 additional zones.
The AUX terminal on the S5050 REMM is capable of supply-
ing up to 100 mA of output current to power sensors and
other devices.
NOTE: Total combined current from the relays and AUX
NOTE: Trouble conditions and tampers, if enabled, are re-
ported via the keypad bus. The report routing is defined in
Block 4, CL 158 and 159, respectively.
output terminal may not exceed 100 mA.
Refer to the S5050 REMM Installation Instructions (P/
N 5-051-453-00) for additional information regarding the
set up, configuration, and operation of the S5050 REMM.
Power is supplied by connecting the KPWR terminal on
the S5058 ZEM PCB to the KPWR or AUX terminal on the
control panel and the C terminal on the ZEM to the C ter-
minal on the control panel. The GND terminal on the ZEM
PCB is for connecting earth ground to the ZEM.
There are two VOUT terminals (connected in parallel),
which can provide up to 300 mA of output current to power
sensors or other devices.
Each S5058 ZEM will support up to 8 hardwired zones. If
a zone is programmed as a SpreadNet zone (see Block
2, CL 111 - 142), it is not available for use as a hardwired
zone.
Figure 8
The S5050 Relay/Event Memory Module (REMM) PCB Layout
Additional setup and wiring information is available in the
S5058 Zone Expansion Module Installation Instruc-
tions (P/N 5-051-454-00).
Switch Settings
The S5050 REMM has five (5) dip switches (S1-1 thru S1-
4 and S2-1) which can be used to provide AUX power to
the relay outputs. The default setting for each switch is
“OFF.” In this position, each relay uses the switched (S)
and common (C) terminals. Each relay is independently
programmable by the installer.
With the switch in the ON position, the +12 VDC AUX
power is applied to the respective Relay switched (S) out-
put terminal (see Figure 9, below).
Switch Configuration
Figure 9, below, shows the relationship of the switches to
the relays on the REMM.
Figure 10
S5058 Zone Expansion Module (ZEM) PCB Layout
ZEM Addressing
S2-2 is used to address the REMM. Leave S2-2 in the ON
position for REMM #1. Change S2-2 to the OFF position
to address REMM #2.
S1-1 and S1-2 are used to address the ZEMs. The ZEM ad-
dress determines which zones are added to the S5832SG
control panel.
Figure 11, below, shows the switch settings to address the
ZEMs. ZEM #1 is used to add zones 9 - 16; ZEM #2 adds
zones 17 - 24; and ZEM #3 adds zones 25 - 32.
Switch
Relay
S1-1
S1-2
S1-3
S1-4
S2-1
R1S
R2S
R3S
R4S
R5S
S1-1 S1-2 S1-3 S1-4 S2-1 S2-2
ON
S1-1
S1-2
Addr. S1-1 S1-2 Zones
1
2
3
on
off
on
off
on
on
9 - 16
17 - 24
25 - 32
Switch
REMM
S2-2
S2-2
ON = REMM #1
OFF = REMM #2
Figure 11
Addressing the ZEM
Figure 9
REMM Switch Settings (shown in default position)
6
SN915-BUS SpreadNet Receiver
The SpreadNet SN915-BUS Bus Receiver connects to the
keypad bus and provides the communication link for all
SpreadNet keypads/keyfobs and zone transmitters.
Digital Communicator Connections
Removing/Installing the Digital Communicator
The digital communicator plugs into the control panel PCB
and is secured by a nylon retaining screw.
NOTE: Tamper and trouble conditions, if enabled, are re-
ported via the keypad bus. The report routing is specified in
Block 4, CL 158 and 159, respectively. Low Battery Report
Routing for the SpreadNet Transmitters is programmed in
Block 4, CL 157.
To remove the digital communicator:
1) Remove AC and DC power from the control panel.
2) Locate and remove the nylon screw. The screw is located
near the upper right-hand corner of the digital commu-
nicator PCB. (See page 1, Figure 1.) Use a #1 phillips
head screwdriver to remove the retaining screw.
3) Unplug the digital communicator from the control panel.
Power for the SN915-BUS may be supplied from either the
KPWR or AUX and C terminals on the control panel to the V+
and GND terminals on the SpreadNet Receiver (see Figure
12).
To install the digital communicator:
1) Ensure that AC and DC power have been removed from
the control panel.
2) Carefully plug the digital communicator into the control
panel PCB. Misalignment of the pins could damage the
control panel.
For additional information on wiring and configuration of the
SN915-BUS Receiver, refer to the SN915-BUS Installation
Instructions (P/N 5-051-440-00).
3) Replace the nylon retaining screw.
4) Apply power.
Digital Communicator Telephone Connections
Line #1
Figure 12
Connecting the SN915-BUS
SN990/991 SpreadNet Keypad/Remote
The control panel can support up to eight SpreadNet key-
pads. There are two different models available, the SN990-
KEYPAD and SN991-REMOTE. Both devices are battery
operated and communicate with the panel through the
SpreadNet SN915-BUS RF Receiver.
SpreadNet keypads provide one-way communication only
and do not display any panel status information.
Additional information on the SpreadNet keypad and remote
may be found in the SN990/991 Installation Instructions (P/N
5-051-556-00).
Figure 13
Telephone Connections
SN961 SpreadNet Keyfob
The Sierra S5832SG control panel can support either a one-
or two-line plug-on digital communicator.
The control panel can have up to eight SpreadNet keyfobs.
Each keyfob will be associated with a specific user number
and will arm, home arm, or disarm the system just like the
user code. The keyfob will communicate with the control panel
via the keypad bus.
The digital communicators have four terminals for connec-
tion to the telephone lines. These terminals are labelled:
Tip, Ring, T1, and R1. The single-line digital communicator
has one set of terminals and the dual-line digital communi-
cator has two sets of terminals. Figure 13 shows how to con-
nect the digital communicator to the incoming phone lines
and the house phones using either a single-line or a dual-
line digital communicator.
SpreadNet keyfob allows one-way communication only and
cannot display any panel status information.
For information on programming the SpreadNet keyfob, refer
to the SN900-PROG Operating Manual (P/N 5-051-136-00
Rev C or later).
7
Figure 14, below, shows the layout of the S5070SG-2 dual-
line digital communicator. The terminals for line 2 are la-
belled Tip, Ring, T2, and R2.
Remote Programming (RPS)
Remote Programming of the Sierra S5832SG control
panel is available with the Commander II software. The
remote programming session can be initiated locally from
the keypad or remotely by the Commander II software.
Setup for Direct Connect to the S5832SG
The procedure for initiating Direct Connect with your
model of Digital Communicator is outlined below.
1. When using Direct Connect, connect the telco cable
from the line side of the modem to the Tip and Ring
terminals on the Digital Communicator (Line 1 only).
2. Move the jumper (J6) to the enabled position, as shown
in Figure 15, below.
3. Start Commander II and open the Panel menu. Select
the Connect option and then click on Direct Connect.
Direct Connect
Disabled
Figure 14
S5070US-2 Dual-line digital communicator
Terminal Connections
Direct Connect
Enabled
Connect the Sierra S5832SG digital communicator to the
telephone line, as shown in Figure 13 (on previous page),
using an approved, 6 or 8 conductor telephone cable (not
included). Connect the cable to the control panel as follows:
Red = Ring
Green = Tip
Grey = Seized Ring (R1)
Brown = Seized Tip (T1)
Blue & Orange = Tamper
Yellow & Black = Not Used
Programming the Panel
Figure 15
The Sierra S5832SG control panel may be programmed
from any keypad connected to the keypad data bus. Con-
nector J8 (see Figure 1) is also available to temporarily con-
nect a keypad, if desired, for programming the panel. The
panel can also be programmed, either remotely or on-site,
using the Commander II software.
Direct Connect using the S5070SG Digital Communicator
4. Enable the Direct Connect jumper (see Figure 15) and
initiate the Direct Connect function in Commander II.
When you hear the modem tones, momentarily short
the Direct Connect pads located on the left-hand side
of the digital communicator PCB. You should hear the
seize relay energize to indicate connection.
The Command Locations used to store the programming
options of the Sierra S5832SG control panel are divided into
10 sections. Each section is called a Block. The configura-
tion of the control panel determines which Blocks are pro-
grammed.
5. Commander II should indicate that the connection has
been established. You are now ready to program the
panel.
6. Be sure to return the jumper to its original position
when the RPS session is completed.
All keypad programming is done from the Installer Program-
ming Mode. To enter the Installer Programming Mode, press
and hold the [1] key for 2 seconds.
Keypad Activated RPS
The following conditions must be met before starting a
keypad activated RPS session:
When programming with an Alphanumeric keypad, you must
select the appropriate language for your panel, followed by
the [Home] key. The icon and LED keypads do not require
the [Home] key to be pressed. On the LED keypad, all LEDs
are off to indicate that you must enter the installer code.
1. The RPS Phone Number must be programmed into
Block 4, CL 085 - 100;
2. Keypad RPS Enable (Block 4, CL 106) must be pro-
grammed for Yes (2);
Next, enter the 6-digit installer code. The default installer
code is [0-1-2-3-4-5]. On the Alphanumeric keypad, press
the [Home] key to use Menu Programming or the [Bypass]
key to use Quick Programming. You are now in installer pro-
gramming mode.
3. RPS/Modem Types (Block 4, CL 107) must match the
configuration of the Commander II software;
4. The phone lines must be connected to the Tip and Ring
terminals on the digital communicator (Line 1 only);
and
To exit the Installer Programming Mode, press and hold the
[CANCEL] key for 2 seconds. This will exit the programming
mode and reset the panel.
8
Keypad Activated RPS (cont.)
Programming With an LED Keypad (cont.)
Cmd Loc 005
(flashing)
5. Commander II must be running at the remote site.
Block
#
(steady)
If the above conditions are met, you are now ready to ini-
tiate the RPS session from an Alphanumeric keypad.
1. Using an Alphanumeric Keypad, enter the Installer
Mode Programming (see Programming With an Alpha-
numeric Keypad on page 10). Select the Menu Pro-
gramming Mode and go to Block 0 (Installer
Commands). Press the [Home] key to accept.
Program Data
(steady)
Figure 18
Reading Programming Data on the LED Keypad
There are three keys used to access and enter data into the
control panel from the keypad. They are the [Bypass],
[Home], and [Cancel] keys. The function of each key is ex-
plained in the next column.
Figure 16
Accessing Installer Commands (Block 0)
Key
Function
2. Scroll through the options, using the [Bypass] key until
you get to the RPS Callback? option (option 10).
[Bypass] Moves the cursor between the Block, Com-
mand Location (Cmd Loc), and Data fields.
Press the [Bypass] key a fourth time to return
the cursor to the Cmd Loc field.
[Home]
This key has several functions, depending
upon the field being edited and the data en-
tered at the keypad.
Figure 17
Activating Keypad RPS
If the Cmd Loc field is active, press the [Home]
key to increment to the next Loc. You may also
enter a new Cmd Loc and press the [Home]
key to move to that Loc. The LEDs for zones 9
- 16 display will show the data stored in the
new Loc.
3. Press [Home] to activate the RPS feature.
Programming With an LED Keypad
You may use an LED keypad to program the control panel.
The LED display on the keypad is used to display all pro-
gramming information: Block Number, Command Location,
and Data. The Block Number is displayed using the Power,
Arm, Ready, and Service LEDs. Command Locations are dis-
played using the LEDs for zones 1 - 8. The LEDs represent-
ing zones 9 - 16 are used to display the program data. Table
6, below, lists the relative value for each LED.
If the Data field is active, pressing the [Home]
key will write the data in the display to the Cmd
Loc indicated. The system will also be incre-
mented to the next Cmd Loc. The Data field
will remain active.
If the Block field is active, press the [Home]
key to increment to the next Block and reset
the Cmd Loc to 001. You may also enter the
number of the desired Block (1 - 10 or 0 - 10
for the Alphanumeric keypad), followed by the
[Home] key to go to that Block.
Upon entering the installer programming mode, all LEDs
will be off. The installer must then enter the installer code
[0-1-2-3-4-5]. The system will then go to Block 1, Command
Location 001 and display the data stored at that location.
The LEDs in the currently active field will blink (if any are lit)
indicating that the data may be edited.
[Cancel] The [Cancel] key allows you to undo changes
to the programming, provided you have not
stored the data. Once the data has been writ-
ten to memory (by pressing the [Home] key),
you cannot use the [Cancel] key to recover the
original data.
Block Numbers
Zone LEDs
Cmd Loc Data
LED
Value
Value
Service
Ready
Arm
1
2
4
8
8
7
6
5
4
3
2
1
16
15
14
13
12
11
10
9
1
2
4
If the data has not been changed and the Cmd
Loc field is active, pressing the [Cancel] key
will decrement to the previous Cmd Loc. If the
Block field is active, pressing the [Cancel] key
will decrement to the previous Block.
Power
8
16
32
64
128
CAUTION: Pressing and holding the [Cancel] key for 2
seconds will Exit Programming Mode.
Table 6
Reading the LEDs
9
Programming With an Alpha Keypad (cont.)
Programming With an Alpha Keypad
Upon entering the installer programming mode, the display
will ask you which language you wish to use for program-
ming the panel. Each panel supports three languages, one
of which is English. The other languages are determined by
the model number of the panel. The Alphanumeric keypad
provides two panel programming options: Quick or Menu
programming. Both options use a combination of text and
numbers in the LCD display.
Key
Function
[Bypass] Used to scroll through the different Menu op-
tions and levels.
[Home] If the PRG> prompt is displayed, this key will
write the data currently displayed to memory
and increment to the next program position.
If the Menu has additional options in sub-
menus, this key will move to the next sub-
menu.
[Cancel] Cancel the operation, if the data has not been
written to memory. If you are in a sub-menu,
this key will back up one level.
Figure 19
Selecting the Language on the Alphanumeric Keypad
CAUTION: Pressing and holding the Cancel key for 2
seconds will Exit Programming Mode.
Once a valid installer code has been entered, the installer
has the option of using either the Quick or Menu Program-
ming mode to enter data into the panel. Each method is
explained below.
Programming With an Icon Keypad
The display on the keypad consists of a 3-digit display for
showing numbers (Blocks, Cmd Locs, and Data) and fixed
text for indicating the type of data displayed.
Figure 20
Selecting the Programming Mode with the Alphanumeric Keypad
Figure 22
Quick Programming Mode
Reading Command Location on the Icon Keypad
Using the Quick Programming mode, you can easily go
directly to any Cmd Loc (Blocks 1 - 10 only; the Installer
Commands, Block 0, are not available in Quick program-
ming mode). This allows you to view or edit any of the
data programmed into the panel.
Figure 23
The Alphanumeric display will show the Block Number (1
- 10) and Programmed Data (varies by location) on the
top line of the display, with the Command Location (var-
ies by Block) shown on the bottom line.
Displaying Block Data on the Icon Keypad
Data will be displayed using only the digits required.
Figure 24
Figure 21
Viewing Program Data on the Icon Keypad
Reading Programming Data on the Alphanumeric Keypad
The [Bypass], [Home], and [Cancel] keys are used to move
between fields and to edit the data in each field, as outlined
previously.
The [Bypass], [Home], and [Cancel] keys are used to
move between fields and to edit the data in each field, as
outlined previously.
Menu Programming Mode
The Menu Programming mode uses menu options and
descriptions to guide you easily through the panel pro-
gramming. You can scroll through the Blocks by press-
ing the [Bypass] key or go directly to any Block by press-
ing the desired key (0 - 10), followed by the [Home] key.
The same three keys ([Bypass], [Home], and [Cancel])
are used in the Menu Programming mode, with slight
variations.
10
Event Memory Codes
Event
Installer Mode Options, (Block 0)
There are 10 Installer Mode Options which are available
from the Menu mode. These options allow the installer to test
the various aspects of the system's operation, program the
Custom Messages used by the Alphanumeric keypads, and
start keypad activated RPS.
Code
1
2
Description
Zone is/was in alarm
Zone is/was tampered
3
4
5
Zone is/was in trouble
Zone alarm/tamper restored
Zone has been bypassed
To access the Block 0 Commands, press and hold the [1] key
for 2 seconds. Use the [Home] and [Bypass] keys to select
the desired language. When prompted, enter your [Installer
Code]. Then press the [Home] key to select Menu mode.
Upon entering the Menu mode, pressing either [0] or [By-
pass] will take you to the first of the Block 0 options.
6
7
8
Zone Unbypassed
Area X disarmed by User Y
Area X armed by User Y
9
User Walk-test started
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
User Walk-test completed
Alarm in Area X canceled by User Y
Comm Fail Receiver X
Comm Fail restore Receiver X
AC power fail
AC power restored
Low Battery (Control Panel)
Low Battery restored (Control Panel)
Master User changed User Code Y
Primary phone line cut
Primary phone line cut restored
Secondary phone line cut
Secondary phone line cut restored
Emergency/medical alarm (hard or soft zone)
Emergency/medical alarm restored (hard / soft)
Panic/police alarm (hard or soft zone)
Panic/police alarm restore (hard / soft)
Fire alarm (hard or soft zone)
Fire alarm restore (hard / soft)
Begin Installer Programming (local)
Installer Programming completed (local)
Supervisory failure Zone X (SpreadNet)
Supervisory failure restore Zone X (SpreadNet)
Low Battery Zone X (SpreadNet)
Low Battery restore Zone X (SpreadNet)
Watchdog reset (panel reset)
Bell failure (Siren loop open or short)
Bell failure restored
Installer Walk-Test
The first option available from the Block 0 Commands is the
Walk-Test? option. To use this option, press [Home]. To pro-
ceed to the next option, press [Bypass].
After installation, the installer can perform a system Walk-
Test. Using this option, the installer can test the operation of
each zone in the system.
While in the Installer Walk-Test Mode, the zones faulted dur-
ing the current Walk-Test session will be annunciated at the
keypad and continuously displayed. This memory will be
purged when exiting Walk-Test Mode.
Event Memory
The second Block 0 Command available is Event Memory.
Press [Home] to access the Event Memory option or [By-
pass] to scroll to the next option.
After selecting Event Memory?, the display will ask if you
wish to Display Event Memory. To display the contents of
the Event Memory, press [Home]. If you wish to Erase Event
Memory, press [Bypass], then press [Home].
Event Memory stores all events which have occurred since
the panel was initially installed or the memory was last
cleared. The Sierra S5832SG control panel has an internal
Event Memory capable of storing up to 60 events with time
and date stamping. By adding the Relay/Event Memory Mod-
ule, the memory capability may be expanded to either 250
events (1 module) or 500 events (2 modules).
Exit fail, Zone X still faulted at end of Exit Delay
Duress code entered for Area X
Kidwatch open failure (Kidwatch time expired)
Begin RPS programming
Events are viewed in chronological order (oldest to newest)
by pressing the [1] key. Events may be viewed in reverse
order (newest to oldest) by pressing the [4] key.
RPS connection failure
Table 7 shows the Event Codes displayed by the LED and
Icon keypads. The event codes are displayed using the zone
LEDs (LED keypad) or the 3-digit display (Icon keypad). The
Sierra Reference Manual contains additional information on
reading the codes with the LED keypad. The events are listed
in numerical order.
RPS programming successful
Test Report (manual or automatic)
Trouble Zone X restored
User Y override of Auto Arming
Tamper Zone X restored
Ground Fault
Ground Fault restored
Brown Out
Brown Out restored
Peripheral communications trouble
Peripheral communications trouble restored
Table 7
Event Memory Codes
11
Custom Messages
Alphanumeric keypads have the ability to display custom-
ized messages. These messages are stored in the control
panel's nonvolatile memory.
Test Report
Following the Custom Messages option is the Send Test
Report option. Selecting this option will initiate a Test Re-
port to the Central Station. The keypad will display a mes-
sage indicating the success or failure of the Report.
To program the Custom Messages, use the [Bypass] key to
scroll to the Custom Messages? screen. Press the [Home]
key to display the first Custom Message (EDIT TROUBLE
MSG).
Test Report with Audibles
This option generates a Test Report to the Central Sta-
tion with all local audibles (internal and external sirens)
sounding for the duration of the Test Report attempt.
Pressing any key during the Test Report period will turn
the sirens off. The system will provide feedback to con-
firm the success or failure of the Report.
There are 41 Custom Messages available. The Edit Trouble
Message, 32 Zone Messages, and 8 Area Messages.
To assist you in entering the Custom Messages, a program-
ming template is included with the keypad. The template
is shown below and the operation of the keys is described
at the top of the next page.
Audible Test
This option turns on all local audibles (internal and exter-
nal sirens) for a period of 5 seconds.
Entry Delay Test
Using this option, the installer can test the Entry Delay to
ensure that a user has sufficient time to enter the pre-
mises and disarm the system without generating an alarm.
To begin the test, scroll to the Entry Delay Tst screen
and press [Home]. Then fault the Entry zone to begin the
delay.
1
2
5
8
0
3
4
7
6
9
Exit Delay Test
Using this option, the installer can test the Exit Delay to
ensure that a user has sufficient time to arm the system
and leave the premises without generating an alarm. To
begin the test, scroll to the Exit Delay Test screen and
press [Home]. The Exit delay will begin immediately.
Bypass
Home CANCEL
Figure 25
The Alphanumeric Keypad Programming Template
Transmit Walk-Test Queue Reports
Walk-Test events stored in Event Memory during the cur-
rent session will be transmitted to the Central Station.
The system will provide feedback to confirm the success
or failure of the Report.
To enter a Message or Label, use the following key com-
mands:
Key
[2]
[8]
[4]
[6]
Function
Scroll forward through characters/symbols
Scroll backward through characters/symbols
Move cursor left one character
Move cursor right one character
RPS Callback
Using this option, the installer can initiate an RPS ses-
sion from the Keypad.
[Cancel] Cancel current changes and restore pre-
vious message, or scroll up one message
[Home] Write message to memory and scroll down
one message
Battery Test
This option allows the installer to perform a Battery Test
on the system. The test starts when you press the [Home]
key. The system will exit the installer programming mode
and reset the panel. The test takes approximately two min-
utes to complete. The battery status will be displayed only
if a Low Battery condition exists.
In addition, other numbers on the keypad enable you to
quickly move to special places in the alphabet. These
special keys are:
[1]
[3]
[7]
[9]
Jump to the space character
Jump to the number 0
Jump to the letter A
Jump to the letter a
NOTE: The [Cancel] key will only restore previous mes-
sages if the message has not been written to
memory using the [Home] key.
12
Programming Summary - Sierra Model S5832SG
Block 1 - Code Option Programming
This programming block is divided into 80 Command Locations (CL 001 - 080). This Block used to program the Installer’s
Code (001-006), Default Installer Code on Power Up (007), Require Installer Code for Direct Connect via RPS (008), and to
set up the User Code parameters. The parameters include setting Maid Code, Duress, and Kidwatch.
Comments
Installer Code
This is a 6-digit code which is required to allow access to installer program-
ming mode. The code is programmed 1 digit per Cmd Loc.
Cmd Loc 001
002 003 004
005 006
Default
Range
0
1
2
3
4
5
0 - 9 0 - 9 0 - 9 0 - 9 0 - 9 0 - 9
Default Installer Code on Power Up?
Comments
Options:
Cmd Loc 007
If enabled (programmed as 2), this restores the Installer
Code to the default value (see CL 001 - 006) following a
power failure/restoral.
1
2
No
Default
Range
2
1 - 2
Yes
Installer Code Required on Direct Connect RPS?
Comments
Options:
Cmd Loc 008
If enabled, the Installer Code (CL 001 - 006) is required
when programming the panel with the direct connect RPS
function of COMMANDER II.
1
2
No
Default
Range
2
1 - 2
Yes
Options:
Maid Code Enable (by Area)
Comments
0
1
2
4
8
Disabled
Saturday
Friday
Thursday
Wednesday
Cmd Loc 009 010 011 012 013 014 015 016
The Maid Code may be specified by active days of
the week and by individual areas. Area 1 may also
use keypad activation for temporary access.
Default
Area
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
Range
0 - 255 (CL 009)
0 - 127 (CL 010 - 016)
NOTE: Maid Code Enable programming deter-
mines when the Maid Code may be used for disarm-
ing the system. The Maid code is always available to
arm the system.
16 Tuesday
32 Monday
64 Sunday
128 By Keypad
Maid Code Hours, Temporary Access, Area 1
Comments
Cmd Loc 017
This option is used in conjunction with keypad activation of the Maid Code
for area 1 only. Duration of the active period is from the time of activation by
grand master user (user #1) or area master (user #12). To disable keypad
(temporary) activation, program this location with 0.
Default
Range
12
0 - 254
Comments
Duress Code Enable (By Area)
Options:
If the system is divided into areas, this option deter-
mines if the duress code associated with a specific
area is active. Refer to the Sierra S5090 Reference
Manual (P/N 5-051-528-01), Block 9 programming
for details on assigning user codes to areas.
Cmd Loc 018
0
1
2
4
8
Disabled
Default
Range
0
Area 1
Area 2
Area 3
Area 4
0 - 255
16 Area 5
32 Area 6
64 Area 7
128 Area 8
Kidwatch Enable
Comments
Options:
Cmd Loc 019
If used, this option must be enabled (program
value > 128) and have the appropriate days of
the week programmed. The Kidwatch timer is
programmed from Block 6, CL 006 - 009. The
same start and end times are used for all days
when the Kidwatch feature is active.
0
1
2
4
8
Disabled
Saturday
Friday
Thursday
Wednesday
Default
Range
0
0, 129 - 255
16 Tuesday
32 Monday
64 Sunday
NOTE: If enabled, the Kidwatch code must be
entered if Area 1 is armed during the Kidwatch
window (see Block 6, CL 006 - 009).
128 Enable (Master)
Keypad Lockout Enable
Comments
Options:
Cmd Loc 020
If enabled, 10 consecutive keystrokes without pro-
ducing a valid user code will cause a keypad
delay starting at 15 seconds and doubling each
time up to a maximum of 240 seconds (4 min).
1
2
3
Disabled
Default
Range
1
1 - 3
When Disarmed
Always Active
13
Block 1 - Code Option Programming (cont.)
User Code Privileges (User # 1 - 60)
Comments
Options:
Cmd Loc 021 022 023 024 025 026 027 028
These programming Options determine which
Options the user is authorized to perform.
Some user codes may have alternate func-
tions. (See Block 9 - Partition Programming
in the Sierra Reference Manual for additional
information.)
0
1
2
4
8
Limited Functions**
User #
Cmd Loc 029 030 031 032 033 034 035 036
User # 10 11 12 13 14 15 16
Cmd Loc 037 038 039 040 041 042 043 044
User # 17 18 19 20 21 22 23 24
Cmd Loc 045 046 047 048 049 050 051 052
User # 25 26 27 28 29 30 31 32
Cmd Loc 053 054 055 056 057 058 059 060
User # 33 34 35 36 37 38 39 40
Cmd Loc 061 062 063 064 065 066 067 068
User # 41 42 43 44 45 46 47 48
Cmd Loc 069 070 071 072 073 074 075 076
User # 49 50 51 52 53 54 55 56
Cmd Loc 077 078 079 080
1
2
3
4
5
6
7
8
Disarm
Arm
Bypass
Open/Close Rpt
9
16 Lang. Code opt. 1
32 Lang. Code opt. 2
Language
English
Spanish
Italian
Program Value
0
16
32
** Limited Functions are user number specific.
They may include relay operation, restricted
SN device operation, and some end-user
functions.
User #
Default
57
58
59
60
15 (All CL)
Range 0 - 47 (All CL)
Block 2 - Zone Configuration Programming
Block 2 is divided into 160 Command Locations (CL 001 - 160) which are used to program the characteristics of each of the zones
in the control panel. The features include Delay Times, Zone Type, Zone Restoral Type, Zone Response Time, Audible Cadence,
Circuit Type, Chime Enable, Shunt Enable, and Home Arm Shunt List. The soft zone programming uses CL 155 - 160.
Entry Delay #1
Comments
Cmd Loc 001
This establishes the first of two delay times for entry zones. Time is entered
in seconds.
Default
Range
20
10 - 255 (Seconds)
Comments
Entry Delay #2
This establishes the second of two delay times for entry zones. Time is
entered in seconds.
Cmd Loc 002
Default
Range
40
10 - 255 (Seconds)
Exit Delay
Comments
Cmd Loc 003
This establishes the delay time for exit zones. The time programmed into
this location should allow the user to use the exit farthest from the keypad.
Time is entered in seconds.
Default
Range
60
20 - 255 (Seconds)
Comments
Options:
Zone Type (Zones 1 - 32)
These programming
Options determine the
zone type for each zone
(hardwired or wireless)
in the system.
8
9
Day Bell/Inst
Day Bell/Delay
0
1
2
3
4
5
6
7
Disabled
Cmd Loc 004 005 006 007 008 009 010 011
Entry Delay 1/Exit
Entry Delay 2/Exit
Interior Instant
Interior Delay 2
Instant (Perim.)
Day Buzzer/Inst
Day Buzzer/Delay
Zone #
Default
1
1
2
3
3
3
4
5
5
5
6
5
7
5
8
10
10 24-Hr. BA
11 Fire (FA)
12 Tamper
13 Panic/Hold-Up
14 Emergency-Med
15 Keyswitch **
Cmd Loc 012 013 014 015 016 017 018 019
Zone # 10 11 12 13 14 15 16
Cmd Loc 020 021 022 023 024 025 026 027
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 028 029 030 031 032 033 034 035
9
Zone #
Default
Range
25
26
27
28
29 30 31
32
** If the Zone Type is programmed as Keyswitch, then Zone Restoral
Type (Block 2, CL 036 - 067) will be programmed using Option #2
values.
0 (CL 012 - 035)
0 - 15 (All CL)
Zone Restoral Type (Zones 1 - 32)
Option Set #1
Comments
Option Set #2
Cmd Loc 036 037 038 039 040 041 042 043
Zone #
Cmd Loc 044 045 046 047 048 049 050 051
Zone # 10 11 12 13 14 15 16
Cmd Loc 052 053 054 055 056 057 058 059
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 060 061 062 063 064 065 066 067
1
2
3
Disabled
Option #1 values are
used for all zone types
except Keyswitch.
1
2
3
4
5
Disabled
Arm/Disarm
Arm Only
Disarm Only
N/A
1
2
3
4
5
6
7
8
Return to normal
Return to normal
and bell silenced
Return to normal
and not armed
User code entry
(zone may remain
faulted)
9
Keyswitch zones will
use the second set of
Options. Default value
for keyswitch is
(Arm/Disarm).
4
5
Zone #
Default
Range
25
2 (All CL)
1 - 5 (All CL)
26
27
28
29 30 31
32
2
14
Block 2 - Zone Configuration Programming (cont.)
Options:
Zone Response Time (Zones 1 - 8)
Comments
1
2
250 mS
500 mS
Cmd Loc 068 069 070 071 072 073 074 075
These Options select the zone response time (in mil-
liseconds) of zones 1 - 8 and zones available from
the S5058 Zone Expansion Module.
Zone #
Cmd Loc
Zone #
Cmd Loc
Zone #
Cmd Loc
Zone #
Default
1
2
3
4
5
6
7
8
076
(Zone Expander Module #1)
(Zone Expander Module #2)
(Zone Expander Module #3)
9 thru 16
077
17 thru 24
078
25 thru 32
2 (All CL)
All zones on the S5058 ZEM use the same re-
sponse time.
Range
1 - 2 (All CL)
Audible Cadence (Zones 1 - 32)
Comments
Options:
Cmd Loc 079 080 081 082 083 084 085 086
These options program the opera-
1
2
3
4
Keypad Buzzer
Zone #
Cmd Loc 087 088 089 090 091 092 093 094
Zone # 10 11 12 13 14 15 16
Cmd Loc 095 096 097 098 099 100 101 102
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 103 104 105 106 107 108 109 110
1
2
3
4
5
6
7
8
tion of the internal and external
sounders. Both internal and exter-
nal sounders will operate together.
Programming options 5 and 6 also
limit the duration of the sounder
outputs.
Pulsing Sounder (1.5s on/off)
Steady Sounder
Temporal Code 3 (0.5s on/
0.5s off 2x, 0.5s on/ 1.5s off)
On 1 Min./Off 30s
(repeated twice)
9
5
6
7
Zone #
Default
Range
25
3 (All CL)
1 - 7 (All CL)
26
27 28 29 30 31 32
On 1 Min./Off 30s
(repeated 5x)
Silent
Exceptions are: Keyswitch/Spread-
Net Arming Annunciation (Block 3,
CL 051) and Ringback (Block 4,
CL 115).
Zone Circuit Type (Zones 1 - 32)
Comments
Options:
Cmd Loc 111 112 113 114 115 116 117 118
Tamper zones use 2 EOL resistors and may
detect 4 discreet conditions (normal, fault/
alarm, trouble, and tamper).
1
2
3
4
5
6
Normally Closed
Normally Open
EOL
Supervised EOL
Tamper (2 EOL)
SpreadNet RF
Zone #
Cmd Loc 119 120 121 122 123 124 125 126
Zone # 10 11 12 13 14 15 16
Cmd Loc 127 128 129 130 131 132 133 134
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 135 136 137 138 139 140 141 142
1
2
3
4
5
6
7
8
9
If any zone is designated as a SpreadNet
zone, it will automatically be ignored as a
hardwired zone.
For devices requiring 10K EOL resistor, use zone 7 and remove J5. Refer
to the S5090 Sierra Reference Manual for additional information.
Zone #
Default
Range
25
3 (All CL)
1 - 6 (All CL)
26
27
28 29 30 31
32
Chime Enable
Comments
Options:
If programmed for chime, these zones will
sound at the keypad when the control panel
is disarmed and the zone is faulted. It is used
for delay, interior, and instant zones only. The
program value is a total of all zones in the
group which will have Chime enabled.
0
1
2
4
8
Disabled
Zone 1
Zone 2 10 18 26
Zone 3 11 19 27
Zone 4 12 20 28
Zones:
Cmd Loc
Default
Range
1 - 8
143
0
9 - 16 17 - 24
25 - 32
146
9
17 25
144
0
145
0
0 - 255
0
0 - 255 0 - 255
0 - 255
16 Zone 5 13 21 29
32 Zone 6 14 22 30
64 Zone 7 15 23 31
128 Zone 8 16 24 32
Zone Bypass Enable
Options:
Comments
0
1
2
4
8
Disabled
Zone 1
Zone 2 10 18 26
Zone 3 11 19 27
Zone 4 12 20 28
Zones:
Cmd Loc
Default
Range
1 - 8
9 - 16 17 - 24
148
255
25 - 32
150
255
These four command locations determine
which zones a user may manually bypass (if
authorized in Block 1, CL 021 - 080).
9
17 25
147
149
255
0 - 255
255
0 - 255 0 - 255
0 - 255
Zone bypass enable is divided into groups
of 8 zones each. The program value is a total
of all zones in the group which may be by-
passed.
16 Zone 5 13 21 29
32 Zone 6 14 22 30
64 Zone 7 15 23 31
128 Zone 8 16 24 32
15
Block 2 - Zone Configuration Programming (cont.)
Comments
Home Arm Bypass List
Options:
These four (4) command locations determine
which zones will be automatically bypassed
when the user home arms the system.
0
1
2
4
8
Disabled
Zone 1
Zone 2 10 18 26
Zone 3 11 19 27
Zone 4 12 20 28
Zones:
Cmd Loc
Default
Range
1 - 8
151
0
9 - 16 17 - 24
152
0
25 - 32
154
9
17 25
153
0
0 - 255
0
0 - 255 0 - 255
0 - 255
The home arm bypass list is divided into
groups of 8 zones each. The value entered is
the total of all zones in the group to be auto-
matically bypassed.
16 Zone 5 13 21 29
32 Zone 6 14 22 30
64 Zone 7 15 23 31
128 Zone 8 16 24 32
Comments
Soft Zone Enable (Medical, Police, and Fire)
Options:
If enabled, press and hold any of the soft zone keys for two
seconds to report an alarm condition (see also Block 4, CL
148 (Report Routing)). The local sounder (Block 2, CL 158 -
160) will also be activated.
Key:
Med
155
1
Police
Fire
157
1
1
2
No
Cmd Loc
Default
Range
156
Yes
1
1 - 2
1 - 2
1 - 2
Comments
Options:
Soft Zone Audible Cadence
These Options program the opera-
tion of the internal and external
sounders in response to the Medi-
cal, Police, and Fire (soft zone)
keys. Both internal and external
sounders will operate together. Pro-
gramming Options 5 and 6 also limit
the duration of the sounder out-
puts.
Key:
Med
158
3
Police
Fire
160
4
1
2
3
4
Keypad Buzzer
Pulsing Sounder (1.5S on/off)
Steady Sounder
Temporal Code 3 (0.5S on/
0.5S off 2x, 0.5 S on/ 1.5 S off)
On 1 Min./ Off 30S
(repeated twice)
Cmd Loc
Default
Range
159
2
1 - 7
1 - 7
1 - 7
5
6
7
On 1 Min./ Off 30S
(repeated 5x)
Silent
Block 3 - Armed System Programming
This Block is divided into 54 Command Locations (CL 001 - 054). This Block allows the installer to set the Arming Type, Enable
Autohome, and set the three Quick functions. In addition, the Installer can select the Keypad functions, Cross-Zoning and
Double-Knock functions, Auto Arming and Disarming, and other miscellaneous functions.
Options:
Arming Type
Comments
1
2
3
Goof-Proof
Cmd Loc 001
This option determines the conditions necessary
in order to arm the system (zone status, etc.).
For additional details on arming options, refer to
the S5090 Reference Manual.
Force Arming
Chirp-Alert
Default
Range
1
1 - 3
Autohome Enable
Comments
Options:
Cmd Loc 002
If enabled, arming the system without exiting the premises
will cause the system to automatically home arm (bypass all
zones programmed in Block 2, CL 151 - 154). Perimeter
zones will be armed with all delays active.
1
2
No
Default
Range
1
1 - 2
Yes
Comments
Options:
Quick Arming Enable
1
2
No
Cmd Loc 003
If enabled, quick arming allows the user to arm the system
without entering a user code. Quick arming pertains to full
arming, home arming, and instant arming. System delays
programmed for those functions will be in effect. (See the
S5090 Reference Manual for details on arming features.)
Yes
Default
Range
2
1 - 2
Comments
SpreadNet Single Button Disarming Enable
Options:
If enabled, allows the system to be disarmed using the “Dis-
arm” button on a SpreadNet SN991-REMOTE or SN961-
KEYFOB. With this option enabled, the “Door” button on the
SN991-REMOTE or SN990-KEYPAD may also be used to
activate a relay (see Block 7, CL 001 - 011, option 2).
Cmd Loc 004
1
2
No
Default
Range
2
1 - 2
Yes
Quick Exit Enable
Comments
Options:
Cmd Loc 005
If enabled, quick exit allows the user to Home arm the sys-
tem and then leave the premises at a later time, without the
need to disarm and re-arm the system. Pressing and hold-
ing the [Home] key for two seconds will invoke the quick exit
function.
1
2
No
Default
Range
1
1 - 2
Yes
16
Block 3 - Armed System Programming (cont.)
Quick Bypass Enable
Comments
Options:
Cmd Loc 006
If enabled, quick bypass allows any user to bypass zones
without entering a user code. To bypass a zone, press the
[Bypass] key followed by the 2-digit code for the zone to be
bypassed.
1
2
No
Default
Range
1
1 - 2
Yes
Comments
Options:
Home Arm Exit Delay Enable
1
2
No
If enabled, the exit delay (Block 2, CL 003) will start when a
user presses and holds the [Home] key for two seconds. If
disabled, the exit delay will be ignored and the system will
home arm instantly.
Cmd Loc 007
Yes
Default
Range
1
1 - 2
4X Exit Delay Extension Enable
Comments
Options:
Cmd Loc 008
If enabled, the exit delay (Block 2, CL 003) will restart if the
delay zone is faulted a second or subsequent time during
the exit delay. The exit delay may be restarted up to 4 times.
1
2
No
Default
Range
2
1 - 2
Yes
Chirp-Alert on Exit Fail
Comments
Options:
Cmd Loc 009
If enabled, all sounders (internal and external) will chirp for
three seconds at the start of the entry delay (Block 2, CL
001 or 002).
1
2
No
Default
Range
2
1 - 2
Yes
Low Battery Arming
Options:
Comments
Cmd Loc 010
1
2
No
If enabled, allows the system to be armed even if the back-
up battery is low.
Default
Range
2
1 - 2
Yes
Keypad Buzzer During Exit Delay
Comments
Options:
Cmd Loc 011
If enabled, the keypad buzzer sounds during the exit delay.
The keypad buzzer rate is faster during the last 10 seconds
of the exit delay.
1
2
No
Default
Range
2
1 - 2
Yes
Comments
Options:
Keypad Buzzer During Entry Delay
If enabled, the keypad buzzer sounds during the entry de-
lay. The keypad buzzer rate is faster during the last 10
seconds of the entry delay.
1
2
No
Cmd Loc 012
Yes
Default
Range
2
1 - 2
Comments
Options:
Keypad LED Status
This option controls the zone
and status displays of the
LED keypad.
1
2
Always display arm and zone status
Status always on while disarmed. If
armed, status displayed for 30 secs.
Display arm and zone status for 30
seconds following User Code entry.
Cmd Loc 013
Default
Range
1
1 - 3
3
NOTE: The Power and Arm
LEDs on all keypads oper-
ate the same.
Options:
Comments
Cross-Zoning List
If programmed for cross-zoning, any two
of the zones listed here must be violated
while armed in order for an alarm condition
to register.
0
1
2
4
8
Disabled
Zone 1
Zone 2 10 18 26
Zone 3 11 19 27
Zone 4 12 20 28
Zones:
Cmd Loc
Default
Range
1 - 8
014
0
9 - 16 17 - 24
25 - 32
017
9
17 25
015
0
016
0
0 - 255
0
0 - 255 0 - 255
0 - 255
If the system is divided into areas, both
zones in alarm must be within the same area.
16 Zone 5 13 21 29
32 Zone 6 14 22 30
64 Zone 7 15 23 31
NOTE: Fire, delay, and keyswitch zones
are ignored if placed on the cross-zone list. 128 Zone 8 16 24 32
Double-Knock List
Comments
Options:
Zones listed here must be violated twice
(or any two zones must be faulted) within
a 30-second period in order for an alarm
condition to register.
0
1
2
4
8
Disabled
Zone 1
Zone 2 10 18 26
Zone 3 11 19 27
Zone 4 12 20 28
Zones:
Cmd Loc
Default
Range
1 - 8
9 - 16 17 - 24
25 - 32
021
9
17 25
018
019
0
020
0
0
0
0 - 255
0 - 255 0 - 255
0 - 255
If the system is divided into areas, the
alarms must be within the same area.
16 Zone 5 13 21 29
32 Zone 6 14 22 30
64 Zone 7 15 23 31
128 Zone 8 16 24 32
NOTE: Fire, delay, and keyswitch zones
are ignored if placed on this list.
17
Block 3 - Armed System Programming (cont.)
Auto-Arming Enable (Area)
Comments
Options:
Cmd Loc 022
Auto-Arming may be enabled for any or all partitions. If
enabled, the system will be automatically armed each
day at the time specified in Block 3, CL 023 and 024. All
partitions will auto-arm using the same timer.
0
1
2
4
8
Disabled
Default
Range
0
Area 1
Area 2
Area 3
Area 4
0 - 255
Auto-Arming Time (Hours)
Cmd Loc 023
When programming the time of day for auto-arming,
use the 24-hour format. (Add 12 hours for afternoon
and evening times.)
16 Area 5
32 Area 6
64 Area 7
128 Area 8
Default
Range
0
0 - 23
The internal sounder will sound a warning two min-
utes and again at one minute prior to the Automatic
Arming of the system.
Auto-Arming Time (Minutes)
Cmd Loc 024
Default
Range
0
0 - 59
Auto-Disarming Enable (Area)
Comments
Options:
Cmd Loc 025
This will automatically disarm the partitions indicated
according to the information programmed into Block
3, CL 026 - 028. The value programmed is a total of all
areas to auto-disarm within the system.
0
1
2
4
8
Disabled
Area 1
Area 2
Area 3
Area 4
Default
Range
0
0 - 255
16 Area 5
32 Area 6
64 Area 7
128 Area 8
Auto-Disarming Enable (Day of Week)
Comments
Options:
Cmd Loc 026
This will automatically disarm the areas specified
in Block 3, CL 025. Auto-disarm will occur on the
days programmed (Block 3, CL 026) and at the
time specified (Block 3, CL 027 - 028). The value
programmed in Block 3, CL 026 is the total of all
days to auto-disarm the system.
0
Disabled
Saturday
Friday
Thursday
Wednesday
Default
Range
0
1
2
4
8
0 - 127
Auto-Disarming Time (Hours)
Cmd Loc 027
16 Tuesday
32 Monday
64 Sunday
Default
Range
0
When programming the time of day for auto-dis-
arming, use the 24-hour format. (Add 12 hours for
afternoon and evening times.)
0 - 23
Auto-Disarming Time (Minutes)
Cmd Loc 028
Default
Range
0
0 - 59
Comments
Swinger Alarm Lockout Limit
Limits the number of alarm signals reported and/or annunciated during an
armed period. Additional alarms will not be indicated. Setting the limit to
zero (0) indicates unlimited signals reported. In partitioned systems, this
limit pertains to ALL partitions (areas).
Cmd Loc 029
Default
Range
0
0 - 15
Options:
Audible Output Limits
Comments
1
2
3
Unlimited Local Audibles.
Cmd Loc 030
Determines the number of times the
sounders (bells) will indicate an alarm
condition during an armed period.
One Audible per Zone.
One Audible per Area.
Default
Range
2
1 - 3
Fire Verification Enable
Comments
Options:
Cmd Loc 031
Determines if powered loop
(zone 8) or switched aux
power will be reset for fire
alarm verification.
1
2
3
4
No Verification
Default
Range
1
1 - 4
Powered Loop Verify Only
Switched Aux Verify Only
Powered Loop and Switched Aux
AC Power Loss Delay Before Report (Minutes)
Comments
Cmd Loc 032
Specifies the number of minutes AC power must be interrupted before an
AC power fail report is sent.
Default
Range
15
1 - 255
Battery Test Interval (Hours)
Comments
Cmd Loc 033
The interval (in hours) between battery tests. If programmed for 0, the test
is disabled. This test is conducted each time the system is reset. Additional
tests follow the test interval specified.
Default
Range
24
0 - 24
18
Block 3 - Armed System Programming (cont.)
Sounder Turn-On Delay Following Alarm (Seconds)
Comments
Number of seconds that elapse following an alarm condition before the
internal siren/external bell sounds. The keypad buzzer is active during this
period.
Cmd Loc 034
Default
Range
0
0 - 255
Strobe/Siren Disable with Low Battery
Comments
Options:
If enabled, this option disables the strobe/siren, to extend
backup time with a low battery condition.
1
2
No
Cmd Loc 035
Yes
Default
Range
2
1 - 2
Comments
Phone Line Cut or Comm Fail Indication (Silent
to Audible)
Cmd Loc 036
Options:
If enabled, alarm conditions programmed as silent will con-
vert to audible.
1
2
No
Yes
Default
Range
1
1 - 2
Comments
Options:
Phone Line Cut Audible Action
Determines the audible action
to be taken when the tele-
phone line has been cut.
1
2
3
No Local Audible Annunciation.
Turn On Sounders.
Turn On Sounders only if armed.
Cmd Loc 037
Default
Range
1
1 - 3
Comments
Internal/External Sounder Output Duration
Amount of time the internal siren and external bell will sound following an
alarm condition. Sounder cadence is progammed in Block 2, CL 079 - 110.
(Minutes)
Cmd Loc 038
Default
Range
5
0 - 60
Comments
This option specifies the duration of the strobe
output (in days) following an alarm condition.
Options:
Strobe Output Duration (Days)
0
Strobe Disabled
Cmd Loc 039
1 - 6 Days
Default
Range
7
0 - 7
7
Strobe Latched
Comments
Soak Mode (Learning Period) Duration (Days)
Panel will operate as a local system only during this period. This will give
the user time to learn the system. All alarm indications during this period will
only be annunciated by keypad buzzer. The internal and external sound-
ers are also disabled during this period.
Cmd Loc 040
Default
Range
0
0 - 31
Duress Active Only When (Area) Armed
Comments
Options:
Cmd Loc 041
If enabled, the duress code will only disarm the system. The
duress code may not be used for arming.
1
2
No
Default
Range
2
1 - 2
Yes
If disabled, this option will send a duress report when arming or disarming.
Opening Report Programming Override
Comments
Options:
Cmd Loc 042
An Opening Report will be sent if the following conditions
are met:
1
2
No
Default
Range
1
1 - 2
Yes
1 - An alarm has occurred;
2 - the cancel report timer (Block 4, CL 110) has expired; and
3 - a valid user code is entered.
The report is sent, regardless of the User Code Privileges (Block 1,
CL 021 - 080) assigned to the user. The report will not override First
to Open/Last to Close (Block 9, CL 110) option.
Options:
Comments
External Bell Supervision Enable
1
2
No
If enabled, provides for supervision of external bell wiring
for opens, shorts, and ground faults. Bell supervision re-
quires an EOL resistor at the bell terminals. This option may
not be used if External Bell Reverse (Block 3, CL 048) is
active.
Cmd Loc 043
Yes
Default
Range
1
1 - 2
For proper supervision, Ground Fault Supervision (Block 3, CL 053) should
also be enabled.
19
Block 3 - Armed System Programming (cont.)
Options:
Keypad Tamper Switch Enable (By Address)
Comments
0
1
2
4
8
Disabled
Each Cmd Loc will be programmed with
the total of the keypad addresses with ac-
tive tamper switches.
Keypad # 1 - 8
9 - 16
045
Keypad
Keypad
Keypad
Keypad
1
2
3
4
5
6
7
8
9
Cmd Loc
Default
Range
044
0
10
11
12
13
14
15
16
0
0 - 255
0 - 255
Keypad Tampers are reported via the
keypad bus.
16 Keypad
32 Keypad
64 Keypad
128 Keypad
Reserved for Future Use
Comments
Cmd Loc 046 047
These locations are Reserved for Future Use and are not available in this
firmware version.
Default
Range
0
0
N/A N/A
External Bell Reverse Enable
Comments
Options:
Cmd Loc 048
If enabled, supplies voltage to external bell when bell is off.
This option may not be used with External Bell Supervision
(Block 3, CL 043) enabled.
1
2
No
Default
Range
1
1 - 2
Yes
Options:
Comments
Sounder (Bell) Test Enable (By Area)
0
1
2
4
8
Disabled
Area 1
Area 2
Area 3
Area 4
Sounds a 5-second bell test at the start of each exit
delay. The value programmed into this Cmd Loc is the
total of all areas for which the bell test will be active.
Cmd Loc 049
Default
Range
0
0 - 255
16 Area 5
32 Area 6
64 Area 7
128 Area 8
Home Arming Enable
Comments
Options:
Cmd Loc 050
This option, when enabled, allows a system to be home
armed or instant home-armed. All zones listed in the
Home Arm Bypass List (Block 2, CL 151 - 154) will be
automatically bypassed.
1
2
No
Default
Range
1
1 - 2
Yes
Keyswitch/SpreadNet Arming Annunciation
Options:
Comments
Cmd Loc 051
0
1
2
4
8
No Annunciation
Keypad Buzzer
Strobe
Internal Siren
External Bell
This option determines how keyswitch or
SpreadNet arming is annunciated. The value
programmed into this Cmd Loc is the total of
all sounders to be activated. When arming,
the selected sounders will beep three times
(1.5 sec on/off) and the strobe will light for 3
seconds. When disarming, the selected
sounders will beep once and the strobe will
be on for 1.5 seconds.
Default
Range
0
0 - 15
Auto-Arming Enable (Day of Week)
Comments
Options:
Cmd Loc 052
This will automatically arm the areas specified in
Block 3, CL 022 at the time specified in Block 3,
CL 023 and 024. The value programmed here is
the total for all days of the week when the system
will auto-arm.
0
Disabled
Default
Range
0
1
2
4
8
Saturday
Friday
Thursday
Wednesday
0 - 127
16 Tuesday
32 Monday
64 Sunday
Ground Fault Supervision Enable
Comments
Options:
Cmd Loc 053
This option, when enabled, reports and annunciates all
ground fault conditions.
1
2
No
Default
Range
1
1 - 2
Yes
When disabled, these conditions are not reported or
annunciated.
20
Home Arm Reports Enable
Comments
Options:
Cmd Loc 054
This option, when enabled, allows opening/closing and by-
pass reports to be sent to the central station, if programmed
in Block 1, CL 021 - 080 (User Code Privilege) and Block 5,
CL 069 - 072 (Zone Bypass Reports); CL 095 - 098 (Open-
ing Reports); and/or CL 099 - 102 (Closing Reports).
1
2
No
Default
Range
1
1 - 2
Yes
Block 4 - Digital Communicator Programming
This Block is divided into 164 Command Locations (CL 001 - 164). The programming locations in this Block reflect the
Receiver Type and Message Format for Receivers 1 & 2, Account Numbers, Phone Numbers (Receiver 1, 2, and RPS), Dialing
Parameters and Delays, and Call Routing (including SpreadNet).
Receiver Type (Receiver #1)
Options:
9
Radionics / Fast
Cmd Loc 001
1
2
3
4
5
6
7
8
ADEMCO 4+2 Express (DTMF)
10 Radionics / Slow
Default
Range
2
ADEMCO Contact ID (DTMF)
ADEMCO High Speed (DTMF)
SIA Level 1 (FSK)
SIA (Date and Time)
SIA (Area)
SIA (Date & Time + Area)
CFSK-IV (FSK)
11 Silent Knight / ADEMCO Fast
12 Silent Knight / ADEMCO Slow
13 Radionics High Speed
14 Numeric DTMF Pager (4+2)
15 Personal Dialing
1 - 15
NOTE: ADEMCO High Speed (option #3) may not be used
with systems having more than 8 zones.
Options:
Comments
Message Format (Receiver #1)
1
2
3
4
3/1 Dual Round
Specifies the method of sending the
reported message (Account Num-
ber and Reporting Code) to the
Central Station.
Cmd Loc 002
4/1 Dual Round
4/2 Dual Round
3/1 Extended Dual Round
Default
Range
1
1 - 4
NOTE: The 4/1 Message Format may not be
used with Radionics High Speed.
Options:
Receiver Type (Receiver #2)
8
9
CFSK-IV (FSK)
Radionics / Fast
1
2
3
4
5
6
7
ADEMCO 4+2 Express (DTMF)
ADEMCO Contact ID (DTMF)
ADEMCO High Speed (DTMF)
SIA Level 1 (FSK)
SIA (Date and Time)
SIA (Area)
Cmd Loc 003
Default
Range
2
10 Radionics / Slow
1 - 15
11 Silent Knight / ADEMCO Fast
12 Silent Knight / ADEMCO Slow
13 Radionics High Speed
14 Numeric DTMF Pager (4+2)
15 Personal Dialing
SIA (Date & Time + Area)
NOTE: ADEMCO High Speed (option #3) may not be used with
systems having more than 8 zones.
Message Format (Receiver #2)
Comments
Options:
Cmd Loc 004
Specifies the method of sending the re-
ported message (account number and
reporting code) to the central station.
1
2
3
4
3/1 Dual Round
Default
Range
1
1 - 4
4/1 Dual Round
4/2 Dual Round
3/1 Extended Dual Round
NOTE: The 4/1 Message Format may not be
used with Radionics High Speed.
Account #1
Comments
Cmd Loc 005
006
0
007
0
008
0
009
0
010
0
This is a 6-digit account number which is used by Receiver 1.
Default
Range
0
In a partitioned system, this is the account number for area #1.
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
Account #2
Comments
Cmd Loc 011
012
0
013
0
014
0
015
0
016
0
This is a 6-digit account number which is used by Receiver 2.
Default
Range
0
In a partitioned system, this is the account number for area #2.
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
21
Block 4 - Digital Communicator Programming (cont.)
Account #3
Comments
Cmd Loc 017
018
0
019
0
020
0
021
0
022
0
In a partitioned system, this is the account number for area #3.
Default
Range
0
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
Account #4
Comments
Cmd Loc 023
024
0
025
0
026
0
027
0
028
0
In a partitioned system, this is the account number for area #4.
Default
Range
0
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
Account #5
Comments
Cmd Loc 029
030
0
031
0
032
0
033
0
034
0
In a partitioned system, this is the account number for area #5.
Default
Range
0
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
Account #6
Comments
Cmd Loc 035
036
0
037
0
038
0
039
0
040
0
In a partitioned system, this is the account number for area #6.
Default
Range
0
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
Account #7
Comments
Cmd Loc 041
042
0
043
0
044
0
045
0
046
0
In a partitioned system, this is the account number for area #7.
Default
Range
0
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
Account #8
Comments
Cmd Loc 047
048
0
049
0
050
0
051
0
052
0
In a partitioned system, this is the account number for area #8.
Default
Range
0
0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15
Options:
Telephone Number (Receiver #1)
Cmd Loc 053 054 055 056 057 058 059 060
Cmd Loc 061 062 063 064 065 066 067 068
Comments
0 - 9 Dialing Digits
Each telephone number may be
up to 16 digits long. Acceptable
values are the digits 0 - 9 and the
special characters shown at the
right.
10 Dial Tone Detect
11 Not Used
12 * [Star Key] - Not Available
with Pulse Dialing
13 # [Pound Key] -Not Avail-
able with Pulse Dialing
14 End of Number - All Cmd
Locs following this charac-
ter are ignored
Default
Range
14 (All Locations)
0 - 15 (All Locations)
Telephone Number (Receiver #2)
Cmd Loc 069 070 071 072 073 074 075 076
Cmd Loc 077 078 079 080 081 082 083 084
Default
Range
14 (All Locations)
0 - 15 (All Locations)
15 5 second Dialing Pause
Telephone Number (RPS Callback)
Cmd Loc 085 086 087 088 089 090 091 092
Cmd Loc 093 094 095 096 097 098 099 100
Default
Range
14 (All Locations)
0 - 15 (All Locations)
Options:
Dial Type
Comments
1
2
3
DTMF (5 tones/sec)
Pulse
DTMF/Pulse Alternating (DTMF first)
Cmd Loc 101
Determines the format
used for all dialing opera-
tions.
Default
Range
1
1 - 3
Dial Attempt Limit
Comments
Cmd Loc 102
Determines the number of times the digital communicator will attempt to
place a call (per phone number) before reporting a comm fail. To set up
the system as a local panel (non-reporting), enter 0 into this location.
Default
Range
6
0 - 15
Telephone Ring Cadence
Comments
Options:
Cmd Loc 103
This is the ring cadence used by the local telephone
system. In a double-ring system, two rings count as
a one.
1
2
Single Ring
Double Ring
Default
Range
2
1 - 2
Options:
Ring Count to Answer
Comments
1
Auto-Answer Disabled
Cmd Loc 104
This option determines the
procedure the system will
use when answering incom-
ing phone calls.
2 - 14 Number of Rings Before Answering
15 Answering Machine Bypass
Default
Range
15
1 - 15
22
Block 4 - Digital Communicator Programming (cont.)
Comments
RPS Callback Enable
Options:
If enabled, requires the panel to call COMMANDER II in
order to establish RPS. If disabled, the panel will stay on-line
when called by COMMANDER II the second time (following
handshaking).
Cmd Loc 105
1
2
No
Default
Range
1
1 - 2
Yes
Keypad RPS Enable
Comments
Options:
Cmd Loc 106
If enabled, allows remote programming to be initiated from
the keypad (either Block 0 or user programming).
1
2
No
Default
Range
2
1 - 2
Yes
RPS and CFSK-IV Modem Type
Comments
Options:
Cmd Loc 107
Establishes the modem protocol for RPS and CFSK-IV
communications.
1
2
Bell 103
CCITT
Default
Range
2
1 - 2
Alarm Dialing Delay (Seconds)
Cmd Loc 108
Comments
The delay (in seconds) after an alarm occurs before the report is sent.
Default
Range
0
0 - 255
24-Hour Zone Dial Delay
Comments
Options:
Cmd Loc 109
If enabled, uses the time programmed above (Block 4, CL
108) for reporting alarms on 24-hour zones. If disabled, 24-
hour zones report immediately.
1
2
No
Default
Range
1
1 - 2
Yes
Cancel Report Delay (Seconds)
Comments
Cmd Loc 110
The amount of time (in seconds), following an alarm, during which a cancel
report may be sent. The cancel report is not sent if a valid user code is
entered before the alarm dialing delay has expired.
Default
Range
0
0 - 255
Dialer Retry Sequence
Options:
Cmd Loc 111
3
4
Repeat Call Attempt Series at 30 min.
then double interval up to 128 hrs.
No additional Call Attempts After Failed
Series Until New Report is Queued.
1
Repeat Call Attempt
Series Every 30 min.
Repeat Call Attempt
Series Every four hrs.
Default
4
1 - 4
Range
2
Phone Line Call Routing
Options:
Cmd Loc 112
3
4
Line #1 with Line #2 as Backup,
Alternating (2 Attempts Each)
Line #1 with Line #2 as Backup,
Alternating (4 Attempts Each)
1
2
Line #1 Only
Default
Range
1
1 - 4
Line #1 with Line #2 Backup
(Phone Line Cut or Comm
Fail)
Test Report Interval (Days)
Comments
Cmd Loc 113
This option determines the test interval. Test reports are sent in daily
intervals, ranging from 1 to 30 days. The time of day for the report is
programmed into Block 4, CL 114. To disable reporting, set to 0.
Default
Range
7
0 - 30
Test Report Time of Day (Hours)
Comments
Cmd Loc 114
When programming the test report time of day, use the 24-hour format.
(Add 12 hours for afternoon and evening times.)
Default
Range
1
0 - 23
Ringback Outputs Enable
Comments
The selected outputs will sound for three sec-
onds following a successful closing report.
Options:
Cmd Loc 115
0
1
2
4
8
Disable
Default
Range
0
Keypad Buzzer
Strobe
Internal Siren
External Bell
0 - 15
23
Block 4 - Digital Communicator Programming (cont.)
Report Routing (Zones 1 - 32)
Comments
Options:
Cmd Loc 116 117 118 119 120 121 122 123
These locations determine the report routing
for alarms, bypasses, troubles, tampers,
restorals, and cancel reports on all zones.
1
2
3
4
5
Disable Reports
Zone #
Cmd Loc 124 125 126 127 128 129 130 131
Zone # 10 11 12 13 14 15 16
Cmd Loc 132 133 134 135 136 137 138 139
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 140 141 142 143 144 145 146 147
1
2
3
4
5
6
7
8
Receiver 1 Only
Receiver 2 Only
Receivers 1 and 2
Receiver 1, with
Receiver 2 as Back-
up, Alternating
9
Zone #
Default
Range
25
2 (All CL)
1 - 5 (All CL)
26
27
28 29 30 31
32
Comments
Keypad Medical, Police, and Fire Report Routing
Report routing for soft zone alarms, if soft
zones are enabled (Block 2, CL 155 - 157).
Cmd Loc
Default
Range
148
2
1 - 5
Duress Report Routing
Comments
Report routing for all duress codes. Areas
are indicated by the account number.
Cmd Loc 149
Default
Range
2
1 - 5
Comments
Report routing for opening and closing re-
ports, if enabled.
Opening / Closing Report Routing
Cmd Loc 150
Default
Range
2
1 - 5
Comments
Report routing for test reports.
Test Report Routing
Cmd Loc 151
Default
Range
2
1 - 5
Comments
Report routing for AC power fail, low battery,
and the respective restoral reports.
Power Supply Report Routing
Cmd Loc 152
Default
2
Range
1 - 5
Phone Line Trouble Report Routing
Comments
Report routing for phone line cut or comm fail
reports.
Cmd Loc 153
Default
Range
2
1 - 5
Kidwatch Check-In Fail Report Routing
Comments
Cmd Loc 154
If Kidwatch is enabled and the Kidwatch code
is not entered during the Kidwatch window
(Block 6, CL 006 - 009), a report will be sent.
Default
Range
2
1 - 5
Installer Programming Report Routing
Comments
Report routing for installer programming start
and end reports (see Block 5, CL 135 - 138).
Cmd Loc 155
Default
Range
2
1 - 5
Bell Supervision Trouble Report Routing
Comments
Report routing for external bell supervision
trouble and restoral reports.
Cmd Loc 156
Default
Range
2
1 - 5
SpreadNet Transmitter Low Battery Report Routing
Comments
Report routing for all SpreadNet transmitters
low battery and restoral reports.
Cmd Loc
Default
Range
157
2
1 - 5
Keypad and Accessory Tamper Report Routing
Comments
Cmd Loc 158
Report routing for all tamper and restoral re-
ports associated with keypads and accesso-
ries connected to the system.
Default
Range
2
1 - 5
24
Block 4 - Digital Communicator Programming (cont.)
Keypad and Accessory Communications
Trouble Report Routing
Comments
Options:
Report routing for all communication trouble
and restoral reports associated with keypads
and accessories connected to the system.
1
2
3
4
5
Disable Reports
Receiver 1 Only
Receiver 2 Only
Receivers 1 and 2
Receiver 1, with
Receiver 2 as Back-
up, Alternating
Cmd Loc 159
Default
Range
2
1 - 5
Audio Verification Enable (Listen-In)
Options:
Cmd Loc 160
1
2
No Audio Verification (AV)
Default
Range
1
1 - 4
Trigger AV following alarm, but before releasing line. Panel may not
seize line for 3 min. or send reports until AV session is complete.
Same as option #1, but allows reports to interrupt AV session.
Same as option #1, except retriggers AV when panel attempts to
seize line to send alarm report.
3
4
Comments
Digital Communications Enable
Options:
If disabled, programmed for No (1), the sys-
tem will operate as a local system. Phone line
checking will also be disabled. For reporting
systems, program this location as Yes (2).
Cmd Loc 161
1
2
No (Local System)
Yes
Default
Range
1
1 - 2
Telephone Line #1 Supervision Time (Minutes)
Cmd Loc 162
Comments
Amount of time (in minutes) that the phone line must be cut (open) before
annunciation will occur and a report is sent to the central station. This is also
the time interval required before the phone line cut action (Block 3, CL 036
and 037). Programming either command location with 0 will disable phone
line checking for that line.
Default
Range
5
0 - 30
Telephone Line #2 Supervision Time (Minutes)
Cmd Loc 163
Default
Range
5
If the system is equipped with a single-line digital communicator, the pro-
gramming of CL 163 will be ignored.
0 - 30
Test Report Phone Line Routing
Comments
Options:
Cmd Loc 164
This option allows the installer to select the phone line
which will be used to send test reports. If a dual-line
digital communicator is used, both lines may be se-
lected for test reporting. The data programmed in
this location overrides the programming of Block 4,
CL 112 for test reports only.
1
2
3
Line #1 Only
Default
Range
1
1 - 3
Line #2 Only
Line #1 and
Line #2
Block 5 - Reporting Digits Programming
This Block has 180 Command Locations (CL 001 - 180). Certain reporting formats such as CFSK-IV, Contact ID, and SIA
have pre-defined codes and the data programmed here is ignored. Reports may be disabled by programming the
reporting code as 0 (or 00 for two-digit codes). Each Cmd Loc may be programmed with any value from 0 - 15.
Report Code, Alarm (Zones 1 - 32)
Cmd Loc 001 002 003 004 005 006 007 008 009 010 011 012
Comments
Default
Zone
0
1
0
1
0
1
0
1
0
1
0
1
These codes are used to indicate alarm conditions. Each report code is a
two-digit code. Reports may be disabled by programming a value of 00
into the Cmd Loc. Each location may contain any digit from 0 - 15.
1
2
3
4
5
6
Cmd Loc 013 014 015 016 017 018 019 020 021 022 023 024
Default
Zone
0
1
0
1
0
1
0
1
0
1
0
1
7
8
9
10
11
12
NOTE: The programmed digits 10 - 15 will be sent to the central station as
their hexadecimal equivalent, as shown in the table below:
Cmd Loc 025 026 027 028 029 030 031 032 033 034 035 036
Default
Zone
0
1
0
1
0
15
1
0
1
0
1
0
1
13
14
16
17
18
Cmd Loc 037 038 039 040 041 042 043 044 045 046 047 048
Reporting Digit Conversion:
Default
Zone
0
1
0
0
0
21
1
0
1
0
1
0
1
Decimal
10
Hexadecimal
19
20
22
23
24
A
B
C
D
E
F
Cmd Loc 049 050 051 052 053 054 055 056 057 058 059 060
11
12
Default
Zone
0
1
0
1
0
27
1
0
1
0
1
0
1
25
26
28
29
30
13
14
Cmd Loc 061 062 063 064
Default
Zone
0
1
0
1
15
31
32
Range
0 - 15 (All CL)
25
Block 5 - Reporting Digits Programming (cont.)
Comments
Report Code, Restoral (Zones 1 - 32)
The restoral report code is a single-digit code. For 2-digit reporting for-
mats, the relative zone number (1 - 8) is sent as the second digit. Disable
the reporting by programming 0 into the specific Cmd Loc. Disabling a
Cmd Loc disables reporting for all zones associated with that location.
Zones:
Cmd Loc
Default
Range
1 - 8
065
1
9 - 16
17 - 24 25 - 32
066
067
1
068
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Comments
Report Code, Zone Bypass (Zones 1 - 32)
The zone bypass report code is a single-digit code. For two-digit reporting
formats, the relative zone number (1 - 8) is sent as the second digit. Disable
this report by programming 0 into the specific Cmd Loc. Disabling a Cmd
Loc disables reporting for all zones associated with that location.
Zones:
Cmd Loc
Default
Range
1 - 8
069
1
9 - 16
17 - 24 25 - 32
070
071
1
072
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Report Code, Trouble (Zones 1 - 32)
Comments
The zone trouble report code is a single-digit code. For two-digit reporting
formats, the relative zone number (1 - 8) is sent as the second digit. Disable
the reporting by programming 0 into the specific Cmd Loc. Disabling a
Cmd Loc disables reporting for all zones associated with that location.
Zones:
Cmd Loc
Default
Range
1 - 8
073
1
9 - 16
17 - 24 25 - 32
075
1
074
076
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Report Code, Tamper (Zones 1 - 32)
Comments
The zone tamper report code is also a single-digit code. For two-digit
reporting formats, the relative zone number (1 - 8) is sent as the second
digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling
a Cmd Loc disables reporting for all zones associated with that location.
Zones:
Cmd Loc
Default
Range
1 - 8
077
1
9 - 16
17 - 24 25 - 32
079
1
078
080
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Report Code, Soft Zone (Medical)
Comments
This is the code sent to the central station when the Medical soft zone is
activated from the keypad. Disable reporting by programming 00 into
these Cmd Loc.
Key:
Medical
081 - 082
Cmd Loc
Default
Range
0
1
0 - 15
Comments
Report Code, Soft Zone (Medical) Restoral
This is the code sent to the central station when the user enters a valid user
code following a keypad-activated Medical emergency. Disable reporting
by programming 00 into these Cmd Loc.
Key:
Medical
Cmd Loc
Default
Range
083 - 084
0
1
0 - 15
Report Code, Soft Zone (Police)
Comments
This is the code sent to the central station when the Police soft zone is
activated from the keypad. Disable reporting by programming 00 into
these Cmd Loc.
Key:
Police
085 - 086
Cmd Loc
Default
Range
0
1
0 - 15
Report Code, Soft Zone (Police) Restoral
Comments
This is the code sent to the central station when the user enters a valid user
code following a keypad-activated Police emergency. Disable reporting
by programming 00 into these Cmd Loc.
Key:
Police
087 - 088
Cmd Loc
Default
Range
0
1
0 - 15
Report Code, Soft Zone (Fire)
Comments
This is the code sent to the central station when the Fire soft zone is acti-
vated from the keypad. Disable the reporting by programming 00 into
these Cmd Loc.
Key:
Fire
089 - 090
Cmd Loc
Default
Range
0
1
0 - 15
Report Code, Soft Zone (Fire) Restoral
Comments
This is the code sent to the central station when the user enters a valid user
code following a keypad-activated Fire emergency. Disable reporting by
programming 00 into these Cmd Loc.
Key:
Fire
Cmd Loc
Default
Range
091 - 092
0
1
0 - 15
Report Code, Duress
Comments
Cmd Loc 093 - 094
This is the code sent to the central station when the user enters a duress
code. (See Block 3, CL 041 to determine when the duress code is active.)
If the system is divided into areas, the area associated with the duress code
will be identified by the account number (see Block 4, CL 005 - 052).
Disable the reporting by programming 00 into the specified Cmd Loc.
Default
Range
0
1
0 - 15
26
Block 5 - Reporting Digits Programming (cont.)
Comments
Report Code, Opening (Users 1 - 60)
User #: 1 - 15 16 - 30 31 - 45 46 - 60
The opening report code is a single-digit code. For two-digit reporting
formats, the relative user number (1 - 15) is sent as the second digit.
Program the specific Cmd Loc with 0 to disable reporting. Disabling a
Cmd Loc disables reporting for all users associated with that location.
Cmd Loc
Default
Range
095
1
0 - 15
096
1
0 - 15
097
1
0 - 15
098
1
0 - 15
Comments
Report Code, Closing (Users 1 - 60)
User #: 1 - 15 16 - 30 31 - 45 46 - 60
The closing report code is a single-digit code. For two-digit reporting
formats, the relative user number (1 - 15) is sent as the second digit.
Program the specific Cmd Loc with 0 to disable reporting. Disabling a
Cmd Loc disables reporting for all users associated with that location.
Cmd Loc
Default
Range
099
1
0 - 15
100
1
0 - 15
101
1
0 - 15
102
1
0 - 15
Report Code, Cancel (Users 1 - 60)
User #: 1 - 15 16 - 30 31 - 45 46 - 60
Comments
The cancel report code is a single-digit code. For two-digit reporting for-
mats, the relative user number (1 - 15) is sent as the second digit. Program
the specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc
disables reporting for all users associated with that location.
Cmd Loc
Default
Range
103
0
0 - 15
104
0
0 - 15
105
0
0 - 15
106
0
0 - 15
Comments
Report Code, Exit Fail Alarm (Zones 1 - 32)
The exit fail report code is a single-digit code which is sent if the exit (delay)
zone remains faulted at the end of the exit delay. The alarm is generated in
association with the Chirp-Alert Warning (Block 3, CL 009). For two-digit
reporting formats, the relative zone number (1 - 8) is sent as the second
digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling
a Cmd Loc disables reporting for all zones associated with that location.
Zones:
Cmd Loc
Default
Range
1 - 8
107
0
9 - 16
17 - 24 25 - 32
108
109
0
110
0
0 - 15
0
0 - 15
0 - 15
0 - 15
Report Code, Kidwatch Check-in Failure
Comments
Cmd Loc 111 112
This two-digit code is sent to the central station if the Kidwatch code (user
#11) is not entered during the Kidwatch period (Block 6, CL 006 - 009).
Disable the reporting by programming 00 into these Cmd Loc.
Default
Range
0
0
0 - 15 (All CL)
Comments
Report Code, AC Power Loss
These two-digit codes are used to report AC power failures and restorals.
Only the second digit is sent when using single-digit reporting formats.
Cmd Loc 113 114
Default
Range
0
1
0 - 15 (All CL)
Report Code, AC Power Restoral
Cmd Loc 115 116
Default
Range
0
1
0 - 15 (All CL)
Comments
Report Code, Low Battery
These two-digit report codes will be sent to indicate a low battery condition
or restoral report. When using single-digit reporting formats, only the sec-
ond digit will be sent.
Cmd Loc 117 118
Default
Range
0
1
0 - 15 (All CL)
Report Code, Low Battery Restoral
Cmd Loc 119 120
Default
Range
0
1
0 - 15 (All CL)
Report Code, Test
Comments
Cmd Loc 121 122
This two-digit report code will be sent to indicate a system test. When using
single-digit reporting formats, only the second digit is sent.
Default
Range
0
1
0 - 15 (All CL)
Comments
Report Code, Failure to Report (Comm Fail)
These two-digit report codes will be sent to indicate a comm fail (failure to
report) condition. The reports are also sent to indicate a comm fail restoral.
Only the second digit is sent when using single-digit reporting formats.
Cmd Loc 123 124
Default
Range
0
0
0 - 15 (All CL)
Report Code, Fail to Report (Comm Fail) Restoral
Cmd Loc
Default
Range
125 126
0
0
0 - 15 (All CL)
Report Code, Primary Phone Line Cut
Comments
Cmd Loc 127 128
These two-digit codes are sent when the system detects a primary or
secondary phone line cut, or their respective restorals. When using single-
digit reporting formats, only the second digit is sent.
Default
Range
0
0
0 - 15 (All Locations)
27
Block 5 - Reporting Digits Programming (cont.)
Comments
Report Code, Primary Phone Line Restoral
These two-digit codes are sent when the system detects a primary or
secondary phone line cut, or their respective restorals. When using single-
digit reporting formats, only the second digit is sent.
Cmd Loc 129 130
Default
Range
0
0
0 - 15 (All Locations)
Report Code, Secondary Phone Line Cut
Cmd Loc 131 132
Default
Range
0
0
0 - 15 (All Locations)
Report Code, Secondary Phone Line Restoral
Cmd Loc 133 134
Default
Range
0
0
0 - 15 (All Locations)
Comments
Report Code, Installer Programming Start
This two-digit report code will be sent to indicate the start of installer pro-
gramming. Single-digit reporting formats will only send the second digit to
the central station.
Cmd Loc 135 136
Default
Range
0
0
0 - 15 (All Locations)
Report Code, Installer Programming Complete
Cmd Loc 137 138
Default
Range
0
1
0 - 15 (All Locations)
Report Code, Bell Supervision Trouble
Comments
Cmd Loc 139 140
These two-digit report codes will be sent to indicate an external bell super-
vision trouble condition or a restoral report. When using single-digit report-
ing formats, only the second digit will be sent.
Default
Range
0
0
0 - 15 (All Locations)
Report Code, Bell Supervision Trouble Restoral
Cmd Loc 141 142
Default
Range
0
0
0 - 15 (All Locations)
Report Code, SpreadNet Supervisory Trouble
Comments
The SpreadNet supervisory trouble and supervisory trouble restoral re-
port codes are single-digit codes. For two-digit reporting formats, the
relative zone number (1 - 8) is sent as the second digit. Program the
specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc dis-
ables reporting for all zones associated with that location.
Zones:
Cmd Loc
Default
Range
1 - 8
143
1
9 - 16
17 - 24 25 - 32
144
145
1
146
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Report Code, SN Supervisory Trouble Restoral
Zones:
Cmd Loc
Default
Range
1 - 8
147
1
9 - 16
17 - 24 25 - 32
148
149
1
150
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Report Code, SN Transmitter Low Battery
Comments
Zones:
Cmd Loc
Default
Range
1 - 8
151
1
9 - 16
17 - 24 25 - 32
The SpreadNet low battery and low battery restoral report codes are a
single-digit code. For two-digit reporting formats, the relative zone number
(1 - 8) is sent as the second digit. Program the specific Cmd Loc with 0 to
disable reporting. Disabling a Cmd Loc disables reporting for all zones
associated with that location.
152
153
1
154
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Report Code, SN Tx Low Battery Restoral
Zones:
Cmd Loc
Default
Range
1 - 8
155
1
9 - 16
17 - 24 25 - 32
156
157
1
158
1
0 - 15
1
0 - 15
0 - 15
0 - 15
Report Code, Ground Fault
Cmd Loc 159 160
Comments
These two-digit report codes will be sent to indicate a ground fault condi-
tion or restoral report. When using single-digit reporting formats, only the
second digit will be sent.
Default
Range
0
0
0 - 15 (All CL)
Report Code, Ground Fault Restoral
Cmd Loc 161 162
Default
Range
0
0
0 - 15 (All CL)
28
Block 5 - Reporting Digits Programming (cont.)
Comments
Report Code, Report Queue Overflow
This two-digit report code will indicate that the report buffer has over-
flowed. When using single-digit reporting formats, only the second digit is
sent.
Cmd Loc 163 164
Default
Range
0
0
0 - 15 (All CL)
Report Code, SN Keypad Supervisory Failure
Comments
Cmd Loc 165
The SpreadNet keypad supervisory (check-in) failure and restoral report
codes are a single-digit code. For two-digit reporting formats, the keypad
address is sent as the second digit. To disable reporting, program 0 into
the specific location.
Default
Range
1
0 - 15
Report Code, SN Kpd Supervisory Fail Restoral
Cmd Loc 166
Default
Range
1
0 - 15
Report Code, SpreadNet Keypad/Keyfob Low
Battery
Cmd Loc 167
Comments
These report codes apply to the SpreadNet keypad, remote, and keyfob.
The low battery and restoral report codes are a single-digit code. For two-
digit reporting formats, the respective keypad number or user number
associated with the remote/keyfob will be sent as the second digit. To
disable reporting, program 0 into the specific location.
Default
Range
1
0 - 15
Report Code, SpreadNet Keypad/Keyfob Low
Battery Restoral
Cmd Loc 168
Default
Range
1
0 - 15
Report Code, Accessory Tamper
Comments
Accessory Addresses
1 - ZEM #1
2 - ZEM #2
3 - ZEM #3
4 - Not Used (Reserved)
5 - REMM #1
Cmd Loc 169
The respective report code is sent to indi-
cate a tamper or trouble condition (or the
respective restoral report) associated with
a specific accessory. For two-digit report-
ing formats, a hardcoded address is
added as the second digit. The addresses
for each accessory are listed to the right.
Default
Range
1
0 - 15
Report Code, Accessory Tamper Restoral
Cmd Loc 170
Default
Range
1
6 - REMM #2
7 - SN915-BUS Receiver
0 - 15
Report Code, Accessory Trouble
Cmd Loc 171
Default
Range
1
0 - 15
Report Code, Accessory Trouble Restoral
Cmd Loc 172
Default
Range
1
0 - 15
Report Code, Keypad Tamper
Comments
Cmd Loc 173 174
These two-digit report codes indicate tamper, trouble, and restoral con-
ditions associated with hardwired keypads. When using single-digit
reporting formats, only the second digit is sent.
Default
Range
0
1
0 - 15 (All CL)
Report Code, Keypad Tamper Restoral
Cmd Loc 175 176
Default
Range
0
1
0 - 15 (All CL)
Report Code, Keypad Trouble
Cmd Loc 177 178
Default
Range
0
0
0 - 15 (All CL)
Report Code, Keypad Trouble Restoral
Cmd Loc 179 180
Default
Range
0
0
0 - 15 (All CL)
29
Block 6 - Real Time Clock Programming
The Real Time Clock Programming Block is divided into two sections and has a total of 9 Command Locations (CL 001
- 009). The two sections relate to the system clock and the Kidwatch timer.
Date (Day of Month)
Comments
Cmd Loc 001
The system clock is used for date and time stamping of events stored in
Default
Range
1
Event Memory. This information is also associated with certain reporting
formats (see Block 4, CL 001 and 003 for additional information).
1 - 31
Date (Month)
Cmd Loc 002
Default
Range
1
1 - 12
Date (Current Year)
Cmd Loc 003
Default
Range
98
00 - 99
Time of Day (Hours)
Cmd Loc 004
Default
Range
0
0 - 23
Time of Day (Minutes)
Cmd Loc 005
Default
Range
0
0 - 59
Comments
Kidwatch Start Time (Hours)
If the Kidwatch feature is enabled (see Block 1, CL 019), the Kidwatch
timer (window) is programmed into these Cmd Locs.
Cmd Loc 006
Default
Range
0
0 - 23
Failure to enter the Kidwatch code during this period will result in the
system sending a Kidwatch Check-In Fail Report (see Block 4, CL 154 and
Block 5, CL 111 - 112 for additional details).
Kidwatch Start Time (Minutes)
Cmd Loc 007
Default
Range
0
0 - 59
Kidwatch End Time (Hours)
Cmd Loc 008
Default
Range
0
0 - 23
Kidwatch End Time (Minutes)
Cmd Loc 009
Default
Range
0
0 - 59
30
Block 7 - Auxiliary Devices Programming
The Auxiliary Devices Programming Block has a total of 79 Command Locations (CL 001 - 079). Each of the first 11
commands has an input range of 1 - 82. Additional relay Options are provided for setting up specific timing operations.
Options:
1 Disabled, relay open
2 Close on SN “Door” button (keypad or re-
mote) activation
3 Closed when entire system armed
4 Closed when entire system disarmed
5 0.5 sec on/off (3x) when keyswitch or Spread-
Net arming; 1.5 sec on for keyswitch or
SpreadNet disarming (ignores timer)
6 Close on any tamper
42 Close when armed, oscillate at 0.5 Hz when
home armed (area 8)
On Board Relay
Cmd Loc 001
43 Close on relay user code 14 entry
44 Close on relay user code 18 entry
45 Close on relay user code 22 entry
46 Close on relay user code 26 entry
47 Close on relay user code 30 entry
48 Close on relay user code 34 entry
49 Close on relay user code 38 entry
50 Close on relay user code 42 entry
51 Close on user code entry (area 1)
52 Close on user code entry (area 2)
53 Close on user code entry (area 3)
54 Close on user code entry (area 4)
55 Close on user code entry (area 5)
56 Close on user code entry (area 6)
57 Close on user code entry (area 7)
58 Close on user code entry (area 8)
59 Close on duress (area 1), open on next area 1
user code entry (except Duress code)
60 Close on duress (area 2), open on next area 2
user code entry (except Duress code)
61 Close on duress (area 3), open on next area 3
user code entry (except Duress code)
62 Close on duress (area 4), open on next area 4
user code entry (except Duress code)
63 Close on duress (area 5), open on next area 5
user code entry (except Duress code)
64 Close on duress (area 6), open on next area 6
user code entry (except Duress code)
65 Close on duress (area 7), open on next area 7
user code entry (except Duress code)
66 Close on duress (area 8), open on next area 8
user code entry (except Duress code)
67 Relay status #1 (see below) (ignores timer)
68 Relay status #2 (see below) (ignores timer)
69 Close on bell supervision trouble
70 Close on keypad/accessory trouble or tamper
71 Close on Medical alarm
Default
Range
1
1 - 82
Relay #1 - REMM #1
Cmd Loc 002
Default
Range
1
1 - 82
Relay #2 - REMM #1
Cmd Loc 003
7 Close when phone line cut
8 Close when comm fail occurs
9 3-sec toggle to activate listen-in (ignores timer)
10 Follow keypad audible sounder (exit/entry de-
lays, area 1 only) (ignores timer)
11 Close on fault (except 24-hr. zone); open when
faulted zone is bypassed, restored, system
armed, or timer
12 Close on any alarm
13 Close on fire alarm
14 Close on burglar alarm
15 Close on panic/holdup
16 Close in installer programming mode
17 Activated by Commander II (RPS)
18 Close at end of exit delay (all areas armed),
open at start of entry delay
19 Close on area 1 alarm
20 Close on area 2 alarm
21 Close on area 3 alarm
22 Close on area 4 alarm
23 Close on area 5 alarm
24 Close on area 6 alarm
25 Close on area 7 alarm
26 Close on area 8 alarm
27 Close when area 1 armed
28 Close when area 2 armed
29 Close when area 3 armed
30 Close when area 4 armed
31 Close when area 5 armed
32 Close when area 6 armed
33 Close when area 7 armed
34 Close when area 8 armed
35 Close when armed, oscillate at 0.5 Hz when
home armed (area 1)
36 Close when armed, oscillate at 0.5 Hz when
home armed (area 2)
37 Close when armed, oscillate at 0.5 Hz when
home armed (area 3)
38 Close when armed, oscillate at 0.5 Hz when
home armed (area 4)
39 Close when armed, oscillate at 0.5 Hz when
home armed (area 5)
Default
Range
1
1 - 82
Relay #3 - REMM #1
Cmd Loc 004
Default
Range
1
1 - 82
Relay #4 - REMM #1
Cmd Loc 005
Default
Range
1
1 - 82
Relay #5 - REMM #1
Cmd Loc 006
Default
Range
1
1 - 82
Relay #1 - REMM #2
Cmd Loc 007
Default
Range
1
1 - 82
Relay #2 - REMM #2
Cmd Loc 008
Default
Range
1
1 - 82
Relay #3 - REMM #2
Cmd Loc 009
72 3-sec toggle for annunciator shutoff (ignores
timer)
73 3-sec toggle on local bell test (ignores timer)
74 Close on alarm associated with zone activated
relay (see Block 7, CL 035 - 066)
75 Close on AC fail
76 Close on low battery
77 Close on chime zone fault
78 Close on system trouble
79 Close on Pre-set Timer #1 (Block 7, CL 067 -
069)
80 Close on Pre-set Timer #2 (Block 7, CL 070 -
072)
Default
Range
1
1 - 82
Relay #4 - REMM #2
Cmd Loc 010
Default
Range
1
1 - 82
Relay #5 - REMM #2
Cmd Loc 011
Default
Range
1
1 - 82
40 Close when armed, oscillate at 0.5 Hz when
home armed (area 6)
81 Close on Pre-set Timer #3 (Block 7, CL 073 -
075)
41 Close when armed, oscillate at 0.5 Hz when
home armed (area 7)
82 Close on Pre-set Timer #4 (Block 7, CL 076 -
078)
Relay status #1
Relay status #2
NOTE: All relays may be programmed to open ac-
cording to a timer (Block 7, CL 013 - 034), unless
otherwise indicated. For additional information,
refer to the S5090 Reference Manual.
System Status Alarms? Relay State
System Status Alarms? Relay State
Disarmed
Disarmed
Armed
No
Yes
No
Yes
Closed
Open
Closed
Open
Disarmed
Disarmed
Armed
No
Yes
No
Yes
Open
Open
Closed
Open
Armed
Armed
NOTE: Relays are open when de-energized.
31
Block 7 - Auxiliary Devices Programming (cont.)
Exit Delay Terminator
Comments
Options:
Cmd Loc 012
If enabled, jumps to the last 5 seconds of the exit delay,
then arms the system. Requires a normally open switch
connected to keypad (TXD and C terminals).
1
2
No
Default
Range
1
1 - 2
Yes
Options:
Timer Units (On Board Relay)
Comments
1
2
3
4
5
Latched
Seconds
Minutes
Hours
Cmd Loc 013
Each relay has its own independent countdown timer.
The timer consists of two parts: the Units and the Counter.
The countdown timer determines the amount of time a
relay will remain closed. For the On-Board Relay, CL 013
stores the units, while CL 014 stores the starting count.
The timer will count backwards and when it reaches 0,
the respective relay will open.
Default
Range
2
1 - 5
Timer Count (On Board Relay)
Cmd Loc 014
Days
Default
Range
30
1 - 255
NOTE: The timer function is ignored if the Relay option (Block 7, CL 001 -
011) is programmed for SpreadNet Arming/Disarming (option #5), Listen-In
Trigger (option #9), Follows Keypad Sounder (option #10), Relay Status #1
(option #67), Relay Status #2 (option #68), 3-second Toggle for Audible
Shutoff (option #72), or 3-second Toggle for Local Bell Test (option #73).
Comments
Timer Units (REMM #1, Relay #1)
For REMM #1, Relay #1, CL 015 stores the units, while
CL 016 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 015
Default
Range
2
1 - 5
Timer Count (REMM #1, Relay #1)
Cmd Loc 016
Default
Range
30
1 - 255
Comments
Timer Units (REMM #1, Relay #2)
For REMM #1, Relay #2, CL 017 stores the units, while
CL 018 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 017
Default
Range
2
1 - 5
Timer Count (REMM #1, Relay #2)
Cmd Loc 018
Default
Range
30
1 - 255
Comments
Timer Units (REMM #1, Relay #3)
For REMM #1, Relay #3, CL 019 stores the units, while
CL 020 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 019
Default
Range
2
1 - 5
Timer Count (REMM #1, Relay #3)
Cmd Loc 020
Default
Range
30
1 - 255
Comments
Timer Units (REMM #1, Relay #4)
For REMM #1, Relay #4, CL 021 stores the units, while
CL 022 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 021
Default
Range
2
1 - 5
Timer Count (REMM #1, Relay #4)
Cmd Loc 022
Default
Range
30
1 - 255
Comments
Timer Units (REMM #1, Relay #5)
For REMM #1, Relay #5, CL 023 stores the units, while
CL 024 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 023
Default
Range
2
1 - 5
Timer Count (REMM #1, Relay #5)
Cmd Loc 024
Default
Range
30
1 - 255
32
Block 7 - Auxiliary Devices Programming (cont.)
Options:
Comments
Timer Units (REMM #2, Relay #1)
1
2
3
4
5
Latched
For REMM #2, Relay #1, CL 025 stores the units, while
CL 026 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 025
Seconds
Minutes
Hours
Default
Range
2
1 - 5
Timer Count (REMM #2, Relay #1)
Cmd Loc 026
Days
NOTE: The timer function is ignored if the Relay option (Block 7, CL 001 -
011) is programmed for SpreadNet Arming/Disarming (option #5), Listen-In
Trigger (option #9), Follows Keypad Sounder (option #10), Relay Status #1
(option #67), Relay Status #2 (option #68), 3-second Toggle for Audible
Shutoff (option #72), or 3-second Toggle for Local Bell Test (option #73).
Default
Range
30
1 - 255
Comments
Timer Units (REMM #8, Relay #2)
For REMM #2, Relay #2, CL 027 stores the units, while
CL 028 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 027
Default
Range
2
1 - 5
Timer Count (REMM #2, Relay #2)
Cmd Loc 028
Default
Range
30
1 - 255
Comments
Timer Units (REMM #2, Relay #3)
For REMM #2, Relay #3, CL 029 stores the units, while
CL 030 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 029
Default
Range
2
1 - 5
Timer Count (REMM #2, Relay #3)
Cmd Loc 030
Default
Range
30
1 - 255
Comments
Timer Units (REMM #2, Relay #4)
For REMM #2, Relay #4, CL 031 stores the units, while
CL 032 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 031
Default
Range
2
1 - 5
Timer Count (REMM #2, Relay #4)
Cmd Loc 032
Default
Range
30
1 - 255
Comments
Timer Units (REMM #2, Relay #5)
For REMM #2, Relay #5, CL 033 stores the units, while
CL 034 stores the starting count. The timer will count
backwards and when it reaches 0, the respective relay
will open.
Cmd Loc 033
Default
Range
2
1 - 5
Timer Count (REMM #2, Relay #5)
Cmd Loc 034
Default
Range
30
1 - 255
Relay Activation By Zone (Zones 1 - 32)
Comments
Options:
Cmd Loc 035 036 037 038 039 040 041 042
These Options determine which relay(s) are
activated following an alarm on a specific
zone. Each relay may be specified by one or
more zones.
0
1
2
3
4
5
6
7
8
9
No Relay Activation
Zone #
Cmd Loc 043 044 045 046 047 048 049 050
Zone # 10 11 12 13 14 15 16
Cmd Loc 051 052 053 054 055 056 057 058
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 059 060 061 062 063 064 065 066
1
2
3
4
5
6
7
8
On Board Relay
REMM #1, Relay #1
REMM #1, Relay #2
REMM #1, Relay #3
REMM #1, Relay #4
REMM #1, Relay #5
REMM #2, Relay #1
REMM #2, Relay #2
REMM #2, Relay #3
9
The specific relay (Block 7, CL 001 - 011)
must be programmed for zone activation (Op-
tion #74).
Zone #
Default
Range
25
0 (All CL)
0 - 11 (All CL)
26
27
28 29 30 31
32
10 REMM #2, Relay #4
11 REMM #2, Relay #5
33
Block 7 - Auxiliary Devices Programming (cont.)
Comments
Options: (CL 067)
Timed Relay Closing (Timer #1 - Day of Week)
These Options will determine the Day(s) of
the Week and Time of Day when the pro-
grammed relay will automatically close. The
value programmed into CL 067 is the total for
all days the relay is to be activated. The relay
to be closed is programmed in Block 7, CL
001 - 011 using Option 79.
0
1
2
4
8
Disabled
Saturday
Friday
Thursday
Wednesday
Cmd Loc 067
Default
Range
0
0 - 127
Timed Relay Closing (Timer #1 - Hours)
Cmd Loc 068
16 Tuesday
32 Monday
64 Sunday
Default
Range
0
0 - 23
Once activated, the relay will remain closed
for the amount of time programmed into the
countdown timer for the specific relay (Block
7, CL 013 - 034).
Timed Relay Closing (Timer #1 - Minutes)
Cmd Loc 069
Default
Range
0
0 - 59
Comments
Options: (CL 070)
Timed Relay Closing (Timer #2 - Day of Week)
These Options will determine the Day(s) of
the Week and Time of Day when the pro-
grammed relay will automatically close. The
value programmed into CL 070 is the total for
all days the relay is to be activated. The relay
to be closed is programmed in Block 7, CL
001 - 011 using Option 80.
Cmd Loc 070
0
1
2
4
8
Disabled
Saturday
Friday
Thursday
Wednesday
Default
Range
0
0 - 127
Timed Relay Closing (Timer #2 - Hours)
Cmd Loc 071
16 Tuesday
32 Monday
64 Sunday
Default
Range
0
0 - 23
Once activated, the relay will remain closed
for the amount of time programmed into the
countdown timer for the specific relay (Block
7, CL 013 - 034).
Timed Relay Closing (Timer #2 - Minutes)
Cmd Loc 072
Default
Range
0
0 - 59
Comments
Options: (CL 073)
Timed Relay Closing (Timer #3 - Day of Week)
These Options will determine the Day(s) of
the Week and Time of Day when the pro-
grammed relay will automatically close. The
value programmed into CL 073 is the total for
all days the relay is to be activated. The relay
to be closed is programmed in Block 7, CL
001 - 011 using Option 81.
0
1
2
4
8
Disabled
Saturday
Friday
Thursday
Wednesday
Cmd Loc 073
Default
Range
0
0 - 127
Timed Relay Closing (Timer #3 - Hours)
Cmd Loc 074
16 Tuesday
32 Monday
64 Sunday
Default
Range
0
0 - 23
Once activated, the relay will remain closed
for the amount of time programmed into the
countdown timer for the specific relay (Block
7, CL 013 - 034).
Timed Relay Closing (Timer #3 - Minutes)
Cmd Loc 075
Default
Range
0
0 - 59
Comments
Options: (CL 076)
Timed Relay Closing (Timer #4 - Day of Week)
These Options will determine the Day(s) of
the Week and Time of Day when the pro-
grammed relay will automatically close. The
value programmed into CL 076 is the total for
all days the relay is to be activated. The relay
to be closed is programmed in Block 7, CL
001 - 011 using Option 82.
Cmd Loc 076
0
1
2
4
8
Disabled
Saturday
Friday
Thursday
Wednesday
Default
Range
0
0 - 127
Timed Relay Closing (Timer #4 - Hours)
Cmd Loc 077
16 Tuesday
32 Monday
64 Sunday
Default
Range
0
0 - 23
Once activated, the relay will remain closed
for the amount of time programmed into the
countdown timer for the specific relay (Block
7, CL 013 - 034).
Timed Relay Closing (Timer #4 - Minutes)
Cmd Loc 078
Default
Range
0
0 - 59
Comments
Options:
Number of REMMs
This option determines where panel events are stored.
0 = No REMMs installed, all events are stored in the
control panel’s event memory (60 events maxi-
mum).
0
1
2
None
Cmd Loc
Default
Range
079
0
0 - 2
REMM 1 only
REMM 1 and 2
1 = REMM #1 installed. Control panel events will be
stored in the REMM (250 events maximum).
2 = Both REMM #1 and REMM #2 are installed.
Control panel events will be stored using a both
REMMs (500 events maximum).
34
Block 8 - SpreadNet Programming
The SpreadNet Programming Block has a total of 45 Command Locations (CL 001 - 045). The SpreadNet transmitters
must be programmed with the SpreadNet Programmer. Refer to the Sierra Reference Manual for additional information.
SpreadNet Channel
Cmd Loc 001
Comments
The Spread Spectrum channel used by the system.
Default
Range
1
1 - 2
SpreadNet Property Code
Cmd Loc 002 003 004 005
Comments
Unique Property Code used to identify a transmitter as being part of the
system. Program one digit per Cmd Loc.
Default
Range
0001
0001 - 4048
SpreadNet Zone Transmitter Supervisory Rates
(Zones 1 - 32)
Comments
Options:
The Supervisory Rate is the time interval
between transmitter check-ins. A total of
eight consecutive supervisory check-ins
must be missed before a supervisory fail-
ure is reported.
1
Unsupervised, Battery
status sent hourly
30 seconds
Cmd Loc 006 007 008 009 010 011 012 013
2
3
4
Zone #
Cmd Loc 014 015 016 017 018 019 020 021
Zone # 10 11 12 13 14 15 16
Cmd Loc 022 023 024 025 026 027 028 029
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 030 031 032 033 034 035 036 037
1
2
3
4
5
6
7
8
120 seconds
300 seconds
9
If option 1 is selected, unsupervised transmitters will send battery status
hourly, only if they are within range of the receiver. Transmitters which are
out of range will not be reported as missing, because they are unsu-
pervised.
Zone #
Default
Range
25
1 (All CL)
1 - 4 (All CL)
26
27
28
29 30 31
32
SpreadNet Keypad Supervisory Rate
(Keypads 1 - 8)
Cmd Loc
Keypad #
Default
038 039 040 041 042 043 044 045
1
2
3
4
5
6
7
8
1 (All CL)
1 - 4 (All CL)
Range
Block 9 - Partition (Area) Programming
This Block has 178 Command Locations (CL 001 - 178) and is used to define all partition information, including which
zones, user codes, and keypads are assigned to each partition. SpreadNet SN991-REMOTEs and SN961-KEYFOBs are
associated with a specific user number and both sections must be programmed for them to function.
Partition Type
Comments
Options:
Cmd Loc 001
This option is used to specify whether or
not a partitioned system has a common
area and the type of display used in the
common area.
1
2
No Common Area
Default
Range
1
1 - 3
Common Area - Full
View Keypad
3
Common Area - Limited
View Keypad
Zone Assignments to Areas (Zones 1 - 32)
Comments
Each zone may be individually assigned to an
Area (Partition) or disabled.
Options:
Cmd Loc 002 003 004 005 006 007 008 009
0
1
2
3
4
5
6
7
8
Zone Disabled
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
Zone #
Cmd Loc 010 011 012 013 014 015 016 017
Zone # 10 11 12 13 14 15 16
Cmd Loc 018 019 020 021 022 023 024 025
Zone # 17 18 19 20 21 22 23 24
Cmd Loc 026 027 028 029 030 031 032 033
1
2
3
4
5
6
7
8
9
Zone #
Default
Range
25
1 (All CL)
0 - 8 (All CL)
26
27
28
29 30 31
32
35
Block 9 - Partition (Area) Programming (cont.)
Area Access by User Number (User # 1 - 60)
Comments
Options:
Cmd Loc 034 035 036 037 038 039 040 041
If common area is enabled, then area 1 must
be active for each user who requires access to
the common area.
1
Area 1(Common
User #
Cmd Loc 042 043 044 045 046 047 048 049
User # 10 11 12 13 14 15 16
Cmd Loc 050 051 052 053 054 055 056 057
User # 17 18 19 20 21 22 23 24
Cmd Loc 058 059 060 061 062 063 064 065
User # 25 26 27 28 29 30 31 32
Cmd Loc 066 067 068 069 070 071 072 073
User # 33 34 35 36 37 38 39 40
Cmd Loc 074 075 076 077 078 079 080 081
User # 41 42 43 44 45 46 47 48
Cmd Loc 082 083 084 085 086 087 088 089
User # 49 50 51 52 53 54 55 56
Cmd Loc 090 091 092 093
User # 57 58 59 60
1
2
3
4
5
6
7
8
Area, if enabled)
Area 2
Area 3
2
4
8
9
Assigned user codes, if used:
System Master Code - user #1
Kidwatch Code - user #11
Area Masters
Area 1 - user #12
Area 2 - user #16
Area 3 - user #20
Area 4 - user #24
Area 4
16 Area 5
32 Area 6
64 Area 7
128 Area 8
Area 5 - user #28
Area 6 - user #32
Area 7 - user #36
Area 8 - user #40
Maid Codes
Area 1 - user #13
Area 2 - user #17
Area 3 - user #21
Area 4 - user #25
Area 5 - user #29
Area 6 - user #33
Area 7 - user #37
Area 8 - user #41
Default 255 (CL 034), 1 (All Other Locations)
Range 1 - 255 (All Locations)
Relay Activation Codes
Area 1 - user #14
Area 2 - user #18
Area 3 - user #22
Area 4 - user #26
Area 5 - user #30
Area 6 - user #34
Area 7 - user #38
Area 8 - user #42
Duress Codes
Area 1 - user #15
Area 2 - user #19
Area 3 - user #23
Area 4 - user #27
Area 5 - user #31
Area 6 - user #35
Area 7 - user #39
Area 8 - user #43
Keypad Assignments to Areas (Keypads 1 - 16)
Options:
Comments
Cmd Loc 094 095 096 097 098 099 100 101
0
1
2
3
4
5
6
7
8
9
Disabled
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
Each keypad may be assigned to any area
(partition) or designated as a Common Key-
pad.
Keypad #
1
2
3
4
5
6
7
8
Cmd Loc 102 103 104 105 106 107 108 109
Keypad #
Default
Range
9
10
1 (All Locations)
0 - 9 (All Locations)
11
12
13
14
15
16
NOTE: Only Alphanumeric keypads may be
designated as Common Keypads.
Common Keypad
Options:
First to Open/Last to Close Enable
Comments
1
2
No
Cmd Loc 110
If enabled (programmed as 2), the first user to disarm any
area will send an opening report to the central station. The
last user to arm any area will send the closing report. The
user must be authorized to send opening/closing reports
(Block 1, CL 021 - 080).
Yes
Default
Range
2
1 - 2
Area Assignments (SpreadNet Keypads 1 - 8)
Comments
Options:
Cmd Loc 111 112 113 114 115 116 117 118
If the system is divided into areas, this option deter-
mines the area(s) associated with each SpreadNet
SN990-KEYPAD. SpreadNet keypads arm and dis-
arm all assigned areas at the same time. The value
programmed into the specific location is the total of
all areas the keypad will be able to access. To send
a Panic report from a SpreadNet keypad, the Police
Soft Zone (Block 2, CL 156) must also be enabled.
0
1
2
4
8
Disabled
Area 1
Area 2
Area 3
Area 4
Keypad #
Default
1
2
3
4
5
6
7
8
0 (All Locations)
0 - 255 (All Locations)
Range
16 Area 5
32 Area 6
64 Area 7
128 Area 8
36
Block 9 - Partition (Area) Programming (cont.)
Area Access (SN Keyfob/Remote # 1 - 60)
Comments
Options:
Cmd Loc 119 120 121 122 123 124 125 126
If the system is divided into areas, this option deter-
mines the area(s) associated with each SpreadNet
SN991-REMOTE or SN961-KEYFOB. The SpreadNet
remotes and keyfobs are associated with a specific
user number and will arm or disarm all assigned areas
at the same time. The value programmed into the spe-
cific location is the total of all areas the remote/keyfob
will be able to access. To send a Panic report from a
keyfob or remote, the Police Soft Zone (Block 2, CL
156) must also be enabled.
0
1
2
4
8
Disabled
User #
Cmd Loc 127 128 129 130 131 132 133 134
User # 10 11 12 13 14 15 16
Cmd Loc 135 136 137 138 139 140 141 142
User # 17 18 19 20 21 22 23 24
Cmd Loc 143 144 145 146 147 148 149 150
User # 25 26 27 28 29 30 31 32
Cmd Loc 151 152 153 154 155 156 157 158
User # 33 34 35 36 37 38 39 40
Cmd Loc 159 160 161 162 163 164 165 166
User # 41 42 43 44 45 46 47 48
Cmd Loc 167 168 169 170 171 172 173 174
User # 49 50 51 52 53 54 55 56
Cmd Loc 175 176 177 178
User # 57 58 59 60
Default 1 (All Locations)
Range 0 - 255 (All Locations)
1
2
3
4
5
6
7
8
Area 1
Area 2
Area 3
Area 4
9
16 Area 5
32 Area 6
64 Area 7
128 Area 8
NOTE: If the user code for the specific user number is
disabled, the remote or keyfob will not work. The
SN991-REMOTE or SN961-KEYFOB may be assigned
to any or all areas to which the user has authority (see
Block 9, CL 034 - 093).
Block 10 - User Code Programming
User Codes (User # 1 - 60)
Comments
Cmd Loc
User #1
Cmd Loc
User #2
001 002 003 004
Each user code is a 4-digit code which may be used to arm and
disarm the system or to bypass zones. Valid entries are the digits
0 - 9. To disable a user code, enter 0-0-0-0 (default code for all
user codes except user #1).
System Master Code
5
8
3
2
005 006 007 008
0
0
0
0
Cmd Loc
User #3
Cmd Loc
User #4
009 010 011 012
User code authority is programmed in Block 1, CL 021 - 080.
User codes are programmed with 1 digit per Cmd Loc.
0
0
0
0
013 014 015 016
0
0
0
0
Cmd Loc
User #5
Cmd Loc
User #6
017 018 019 020
0
0
0
0
021 022 023 024
0
0
0
0
Cmd Loc
User #7
Cmd Loc
User #8
025 026 027 028
0
0
0
0
029 030 031 032
0
0
0
0
Cmd Loc
User #9
033 034 035 036
0
0
0
0
Cmd Loc
User #10
Cmd Loc
User #11
Cmd Loc
User #12
Cmd Loc
User #13
Cmd Loc
User #14
Cmd Loc
User #15
Cmd Loc
User #16
Cmd Loc
User #17
Cmd Loc
User #18
Cmd Loc
User #19
Cmd Loc
User #20
Cmd Loc
User #21
037 038 039 040
0
0
0
0
041 042 043 044
0
045 046 047 048
0
049 050 051 052
0
053 054 055 056
0
057 058 059 060
0
061 062 063 064
0
065 066 067 068
0
069 070 071 072
0
Kidwatch Code
0
0
0
Area 1 Master Code
Area 1 Maid Code
0
0
0
0
0
0
Area 1 Relay Code
Area 1 Duress Code
0
0
0
0
0
0
Area 2 Master Code
Area 2 Maid Code
Area 2 Relay Code
0
0
0
0
0
0
0
0
0
073 074 075 076
0
077 078 079 080
0
081 082 083 084
0
Area 2 Duress Code
Area 3 Master Code
0
0
0
0
0
0
Area 3 Maid Code
0
0
0
37
Block 10 - User Code Programming (cont.)
User Codes (cont.)
Comments
Cmd Loc
User #22
Cmd Loc
User #23
Cmd Loc
User #24
Cmd Loc
User #25
Cmd Loc
User #26
Cmd Loc
User #27
Cmd Loc
User #28
Cmd Loc
User #29
Cmd Loc
User #30
Cmd Loc
User #31
Cmd Loc
User #32
Cmd Loc
User #33
Cmd Loc
User #34
Cmd Loc
User #35
Cmd Loc
User #36
Cmd Loc
User #37
Cmd Loc
User #38
Cmd Loc
User #39
Cmd Loc
User #40
Cmd Loc
User #41
Cmd Loc
User #42
Cmd Loc
User #43
Cmd Loc
User #44
Cmd Loc
User #45
Cmd Loc
User #46
Cmd Loc
User #47
Cmd Loc
User #48
Cmd Loc
User #49
Cmd Loc
User #50
Cmd Loc
User #51
Cmd Loc
User #52
Cmd Loc
User #53
085 086 087 088
Each user code is a 4-digit code which may be used to arm and
disarm the system or to bypass zones. Valid entries are the digits
0 - 9. To disable a user code, enter 0-0-0-0 (default code for all
user codes except user #1).
Area 3 Relay Code
Area 3 Duress Code
Area 4 Master Code
0
0
0
0
089 090 091 092
0
093 094 095 096
0
097 098 099 100
0
101 102 103 104
0
105 106 107 108
0
109 110 111 112
0
113 114 115 116
0
117 118 119 120
0
121 122 123 124
0
125 126 127 128
0
129 130 131 132
0
133 134 135 136
0
137 138 139 140
0
141 142 143 144
0
145 146 147 148
0
149 150 151 152
0
153 154 155 156
0
157 158 159 160
0
161 162 163 164
0
165 166 167 168
0
169 170 171 172
0
173 174 175 176
0
177 178 179 180
0
181 182 183 184
0
185 186 187 188
0
189 190 191 192
0
193 194 195 196
0
197 198 199 200
0
201 202 203 204
0
205 206 207 208
0
209 210 211 212
0
0
0
0
User code authority is programmed in Block 1, CL 021 - 080.
User codes are programmed with 1 digit per Cmd Loc.
0
0
0
Area 4 Maid Code
Area 4 Relay Code
Area 4 Duress Code
Area 5 Master Code
Area 5 Maid Code
Area 5 Relay Code
Area 5 Duress Code
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Area 6 Master Code
Area 6 Maid Code
0
0
0
0
0
0
Area 6 Relay Code
Area 6 Duress Code
Area 7 Master Code
Area 7 Maid Code
Area 7 Relay Code
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Area 7 Duress Code
Area 8 Master Code
0
0
0
0
0
0
Area 8 Maid Code
Area 8 Relay Code
Area 8 Duress Code
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
38
Block 10 - User Code Programming (cont.)
User Codes (cont.)
Comments
Cmd Loc
User #54
Cmd Loc
User #55
Cmd Loc
User #56
Cmd Loc
User #57
Cmd Loc
User #58
Cmd Loc
User #59
Cmd Loc
User #60
213 214 215 216
Each user code is a 4-digit code which may be used to arm and
disarm the system or to bypass zones. Valid entries are the digits
0 - 9. To disable a user code, enter 0-0-0-0 (default code for all
user codes except user #1).
0
0
0
0
217 218 219 220
0
221 222 223 224
0
225 226 227 228
0
229 230 231 232
0
233 234 235 236
0
237 238 239 240
0
0
0
0
User code authority is programmed in Block 1, CL 021 - 080.
User codes are programmed with 1 digit per Cmd Loc.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
39
C & K is a registered trademark of C & K Components
Sierra and SpreadNet are registered trademarks of C & K Systems, Inc.
All other trademarks are the property of their respective owners.
Copyright 1999, C & K Systems, Inc.
P/N 5-051-533-16 Rev A
|