4-178-676-42(1)
Setting up your TV
LCD
To watch TV
Digital Color TV
Setup Guide (Operating Instructions)
Additional Information
Sony Customer Support
United States
Canada
1.800.222.SONY 1.877.899.SONY
Please Do Not Return
the Product to the Store
KDL-60NX810 / 60NX801 / 60NX800 / 55NX811 / 55NX810 / 52NX800 / 46NX810
KDL-46NX800 / 46NX711 / 46NX710 / 46NX700 / 40NX711 / 40NX710 / 40NX700
Table of Contents
Checking the accessories................................................................................................4
• Operating instructions are built into your BRAVIA TV. Refer to “To use i-Manual” for
operation (page 18).
• Retain this manual for future reference.
®
The BRAVIA Full HDTV Experience
•
•
Receive over-the-air HD broadcasts with an
HD-quality antenna connected directly to the
back of your TV.
information on antenna selection and setup.
Discover the wealth of entertainment now
available on super-high resolution Blu-ray
Thank you for choosing Sony! Your new
®
BRAVIA TV opens the door to the “Full HDTV
Experience.” This document will help you get the
most out of your TV.
Please take a moment to register your TV at:
3 DSisoc™unpldayer and other Sony HD equipment.
Four Steps to a Full HD Experience
Set, Source, Sound, and Setup.
Complete the high-definition experience with a
BRAVIA Sync™ surround sound system or A/V
receiver from Sony.
1 Set
Now that you have made the best selection in LCD TV
technology, be sure to remove all accessory contents
from the packaging before setting up your TV.
4 Setup
Install your TV and connect your sources. See
page 9 for sample connection diagrams.
2 Source
TV, you need access to HD programming.
To help assure the highest quality for your HD
experience, use Sony HDMI (High-Definition
Multimedia Interface) cables.
To experience the stunning detail of your BRAVIA
To learn more about HDTV, visit:
U.S.A.: http://www.sony.com/HDTV
•
Upgrade your signal or content source to high-
definition (HD) by contacting your HD service
provider.
This TV displays all video input signals in a resolution of 1,920 dots × 1,080 lines.
3
*3 KDL-60NX801/60NX800 models are
shipped with the parts attached to the TV.
*4 These screws and spacers are required when
installing an optional Wall-Mount Bracket.
You must use these screws instead of the ones
provided with the bracket for safety reasons.
Be sure to keep them in a safe place until you
are ready to use the Wall-Mount Bracket. See
page 23 for the recommended Wall-Mount
Bracket for your TV.
Checking the accessories
For all models
Table-Top Stand (1)*1
Remote control (1)*2
Size AAA batteries (2)
For KDL-60NX801, KDL-60/52/46NX800
and KDL-46/40NX700 models
AC power cord (1)
Inserting batteries into the
remote control
Bottom Cover (1)*3 (KDL-60NX801
and KDL-60/52/46NX800 only)
Stand Rear Cover (1)*3
Fixing screws for Table-Top Stand
(M5 × 16) (4)*3
Assembling Screws for Table-Top
Stand (M5 × 16) (4) (KDL-40NX700 only)
Black Spacers (4)*4
(KDL-52/46NX800 only)
Silver Spacers (4)*4 (KDL-60NX801
and KDL-60NX800 only)
Screws (M6 × 20) (4)*4
1 Remove the protection sheet.
(KDL-60NX801 and KDL-60NX800 only)
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and
KDL-46/40NX710 models
Hexagon wrench (1)
Assembling screws for Table-Top
Stand (4)
(KDL-55NX811, KDL-60/55/46NX810,
KDL-46NX711 and KDL-46NX710 only)
Assembling screws for Table-Top
Stand (2)
(KDL-40NX711, KDL-40NX710 only)
3D Glasses (battery included) (2)
(KDL-55NX811 and KDL-46/40NX711 only)
Pouch for 3D Glasses (2)
2 Push and slide the cover upward.
Guidelines for Remote Control
• Point your remote control directly at the
IR sensor located on your TV.
• Make sure that no objects are blocking the
path between the remote control and the
IR sensor on your TV.
• Fluorescent lamps can interfere with your
remote control; try turning off the
fluorescent lamps.
• If you are having problems with the remote
control, reinsert or replace your batteries and
make sure that they are correctly inserted.
(KDL-55NX811 and KDL-46/40NX711 only)
3D Sync Transmitter (1)
(KDL-55NX811 and KDL-46/40NX711 only)
Double-sided tape (2)
(KDL-55NX811and KDL-46/40NX711 only)
*1 KDL-60NX801/60NX800 models are
shipped with the parts attached to the TV.
KDL-55NX811, KDL-60/55/46NX810,
KDL-46/40NX711, KDL-46/40NX710 and
KDL-40NX700 models requires assembling.
Refer to other leaflet to assemble the Table-
Top Stand.
*2 Please refer to the model name printed on the
remote control.
4
Programming the Remote Control
Your remote control can be programmed to use other equipment and is pre-programmed to
operate the following Sony equipment.
Function Button Sony Equipment Code Number
DVD
AMP
STB
DVD Player
Receiver
31033
52172
Digital Satellite 01639
Programming Other Equipment
Follow the steps below to program your TV remote control.
2
2
1 Look for the code in the Manufacturer’s Code List (refer to
i-Manual) that corresponds to the equipment you would like to
operate with the Sony remote control. If more than one code is
provided, try programming the first code listed. If your
equipment’s code is not listed, visit
list.
4
3
2 Press and hold a DVD, AMP or STB function button
simultaneously with INPUT button and release.
When in the programming mode, the function button (DVD,
AMP, STB) blinks for approximately 30 seconds until a code is
entered.
4
3 Enter the five digit code using
-
while the function
buttons (DVD, AMP, STB) are lit. If the code is not entered
within 30 seconds, you must repeat step 2.
4 Press
or ENT to confirm the code. If successfully
programmed, the function button (DVD, AMP, STB) will blink
twice, if not, it blinks five times.
Confirm the Programming
If you can turn your equipment on and off using the green POWER button, the
programming is complete. If not, try the next code listed.
~
• In some cases, you may not be able to program your remote control. If this is the case, use your
equipment’s own remote control.
• Any of the function buttons (DVD, AMP, STB) can be programmed to operate other equipment
regardless of the labeling. For example, if programmed with the correct code, a Blu-ray Disc player
can be operated with the DVD button. This is useful if your equipment does not match any of the
labeled buttons.
To reset the remote control to the factory default:
Press SCENE, TV POWER, and
simultaneously. The four function buttons (DVD,
AMP, STB, and TV) blink when successfully reset.
5
Setting up your TV
Some TV models are packaged with a
detached Table-Top Stand so you can mount
Attaching the Table-Top
Stand
Refer to the supplied Table-Top Stand
instruction leaflet for proper attachment for
some TV models.
your TV to a wall right away. If you are not
mounting the TV to a wall, you will need to
attach the Table-Top Stand. You will need a
Phillips screwdriver and the supplied screws
to complete the task. Look for the attachment
instructions provided with the TV.
~
Be sure to consider the following while
setting up your TV:
• Do not put stress on the LCD panel or the
frame around the screen.
• Be careful to not pinch your hands or the AC
power cord when you install the TV unit to the
Table-Top Stand.
•
Disconnect all cables when carrying the
TV.
•
Carry the TV with the adequate number
of people; larger size TVs require two or
more people.
For KDL-52/46NX800 and KDL-46/
40NX700
•
Correct hand placement while carrying
the TV is very important for safety and
to avoid damage.
1 Gently slide the TV unit onto the
Table-Top Stand and align the screw
holes.
•
•
•
•
Ensure your TV has adequate
For best picture quality, do not expose the
screen to direct illumination or sunlight.
Avoid installing the TV in a room with
reflective wall and floor materials.
If the TV is brought directly from a cold
to a warm location, or is placed in a very
damp room, or is placed in a room in
which heating has just been turned on,
moisture may condense on the surface or
inside the TV. Should this occur, turn off
the TV and leave the TV off until the
moisture evaporates, and then the TV
can be used. If you notice moisture
condensation between the glass panel
and the LCD, turn on the TV and the
condensation will evaporate after the TV
has warmed up.
2 Use the supplied screws to attach the
TV unit to the Table-Top Stand.
~
• If you use an electric screwdriver, set the
tightening torque at approximately 1.5 N·m
{15 kgf·cm}.
6
3 After all the screws are tighten cover
the Table-Top Stand with the
supplied Stand Rear Cover.
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and
KDL-46/40NX710
1 Align with the two dowels of the
Table-Top Stand, and gently place
the TV, checking the f mark is
facing the front.
2 Attach the TV and Table-Top Stand
with the supplied screw and hexagon
wrench.
~
• Set the torque setting to approximately 3 N·m
{30 kgf·cm}.
Reattaching the Table-Top Stand to
the TV
Attach to the original position using the
removed screws. See “Detaching the Table-
(Continued)
7
Adjusting the viewing angle (except 60-inch models)
This TV can be adjusted within the angles shown below.
For KDL-52/46NX800 and KDL-46/40NX700
0°
6°
1
4
2
3
Remove screw as
shown.
Install screw into the
top screw hole of the
Table-Top Stand.
Slide in.
Lift up and tilt.
~
• Reverse the steps when readjusting the angle back to 0 degree.
For KDL-55NX811, KDL-55/46NX810, KDL-46/40NX711 and KDL-46/
40NX710
0°
6°
8
Connecting the TV
The following chart shows the high-definition (HD) and standard-definition (SD) video
formats supported by your BRAVIA TV inputs.
*1 720/24p format is supported by KDL-55NX811, KDL-60/55/46NX810, KDL-46/
40NX711 and KDL-46/40NX710.
*2 For supported PC formats refer to the i-Manual.
(Continued)
9
Shown with a Set Top Box with HDMI
connection
Shown with a Set Top Box with
COMPONENT connection
Set Top Box
Set Top Box
Cable System or VHF/UHF Antenna System
Cable
or
Antenna
10
Shown with HD BRAVIA® Sync™ Basic Connection
*Rear of TV
*A/V Receiver
AM
SAT
IN
DVD IN
VIDEO 2/BD IN
OUT
L
L
R
R
OPT
VIDOIN1
IN
CODAVXD
AUDIO IN AUDIO IN AUDIO IN
OSPATTIN
FRONT
R
FRONT
L
SUR
R
SUR
L
CENTER SUBWOOFER
*Blu-ray Disc
COMPONENT
VIDEO OUT
VIDEO
OUT
AUDIO
OUT
5.1CH OUTPUT
FRONT REAR CENTER
Y
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
AC IN
L
L
COAXIAL
OPTICAL
P
B/CB
HDMI
OUT
PR
/
CR
R
R
WOOFER
S
VIDEO
HD Cable Box or
HD Satellite Receiver
SAT
(Dish)
Cable/
Antenna
* Signifies a BRAVIA Sync capable device.
Shown with HD Basic Connection with Home Theater System
Side Panel
Rear of TV
Blu-ray Disc/DVD
Cable/SAT (Dish)
SD Cable Box or
SD Satellite Receiver
or
Cable/
Antenna
Home Theater System
(Continued)
11
Shown with PC Connection with SD VCR/DVD
Side Panel
Rear of TV
or
Notebook PC
PC
Splitter
VCR
DVD
VCR/DVD Combo
Cable/Antenna
12
1 Secure the Stand for the TV.
Make sure the TV stand can adequately
support the weight of the TV. Use two angle
braces (not supplied) to secure the stand.
For each angle brace use the appropriate
hardware to:
Securing the TV
Sony strongly recommends
taking measures to prevent
the TV from toppling over.
Unsecured TVs may topple
and result in property
damage, serious bodily
injury or even death.
•
Attach one side of the angle brace to the
wall stud.
•
Attach the other side to the TV stand.
Angle brace
(not supplied)
Preventing the TV from
Toppling
Stand
•
•
Secure the TV to a wall and/or stand.
Do not allow children to play or climb on
furniture and TV sets.
2 Secure the TV to the Stand.
Use the optional hardware listed below (not
supplied):
•
•
Avoid placing or hanging items on the
TV.
Never install the TV on:
– slippery, unstable and/or uneven
surfaces.
– furniture that can easily be used as
steps, such as a chest of drawers.
Install the TV where it cannot be pulled,
pushed, or knocked over.
•
A machine screw (screwed into the TV’s
Table-Top Stand)
For KDL-60NX801, KDL-60/52/
46NX800 and KDL-46/40NX700
Use M4 × 16 screw
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and
KDL-46/40NX710
•
•
Route all AC power cords and
connecting cables so that they are not
accessible to curious children.
Use M4 × 8 screw
•
•
A screw or similar (attach it to the TV
stand)
Rope or chain (strong enough to support
the weight of the TV). Make sure that
there is no excess slack in the rope or
chain.
Recommended Measures to
Secure the TV
Consider the following measures when
securing your TV to a TV stand (not
supplied).
An alternative way to secure the TV is with
an optional Sony Support Belt Kit.
Machinescrew
(not supplied)
Rope or chain
(not supplied)
Screw hole on the
Table-Top Stand
Screw (not supplied)
(Continued)
13
~
Contact Sony Customer Support to obtain the
optional Support Belt Kit by providing your TV
model name.
• For United States call: 1-800-488-7669 or
• For Canada call: 1-877-899-7669
Organizing the AC power
cord
~
• Do not bundle the AC power cord together
with other cables.
3 Anchor the TV to the Wall.
Anchor the TV to the wall by using bolts,
wall anchor and chain (or rope).
For KDL-60NX801, KDL-60/52/
46NX800 and KDL-46/40NX700
~
• KDL-60NX801, KDL-60/52/46NX800 and
KDL-46/40NX700 are shipped with screws
attached to the rear of the TV. (They are
fastened in the screw holes for wall mounting.)
Be sure to remove the upper two screws prior
to anchoring the TV on a wall.
• Securing the TV to the stand without securing
the TV and the stand to the wall provides
minimum protection against the TV toppling
over. For further protection, be sure to follow
the three measures recommended.
~
• After the AC power cord is thread as
illustrated, place the bottom cover (for NX801/
800 series only).
Anchor bolts (not supplied)
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and
KDL-46/40NX710
Rope or
Wall-
mount
holes
chain
(not
supplied)
Wall-anchor
(not
supplied)
14
Detaching the Table-Top
Stand from the TV
Remove only the screws marked with
the TV.
Running initial setup
on
~
• Do not remove the Table-Top Stand for any
reason other than to install corresponding
accessories on the TV.
1 Complete your cable connections
before proceeding with the Initial
Setup.
For KDL-60NX801, KDL-60/52/
46NX800 and KDL-46/40NX700
~
Connect the TV to your nearest power
outlet.
• The NX801/NX800/NX700 series models
must remove the stand rear cover prior to
detaching the Table-Top Stand.
• When installing the TV on a wall, remove the
four screws from the rear of the TV. (They are
fastened in the screw holes for wall mounting.)
Be sure to store the removed screws in a safe
place, keeping them away from children
(except KDL-46/40NX700).
• When attaching the Table-Top Stand again, be
sure to fasten the four screws (previously
removed) to the original holes on the rear of
the TV (except KDL-46/40NX700).
2 Check the ENERGY SAVING
3 PSrWesIsT1CH(PsOetWtinEgRi)s oonn t(hze)T. V.
When you switch the TV on for the
first time, the Language menu
appears on the screen.
~
• The TV image shown here may differ from
your TV but the operation of your TV remains
the same as indicated.
4
Follow the instructions on the screen.
~
• The ENERGY SAVING SWITCH must be on
(z) to set the clock and obtain program
information for the TV Guide.
• Home mode sets the TV to display the settings
optimized for home viewing (this setting is
ENERGY STAR compliant).
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and
KDL-46/40NX710
5 Select Continue to scan for available
channels and enable the TV Guide
®
KDL-60NX810
On Screen feature. If you receive
channels from a cable box or satellite
receiver and do not wish to use the
TV’s built-in tuner, select Skip.
Selecting Skip will disable the TV
Guide On Screen feature, which is
only available when the TV’s tuner is
used.
~
Joint
• If you skip the channel scan while in the setup
menus, TV Guide will be disabled.
15
Using a Wall-Mount Bracket Installing the TV Against a
Your TV can be mounted on a wall using a
Wall or Enclosed Area
Wall-Mount Bracket (not supplied) out of
Make sure that your TV has adequate
the box as packaged. Some larger size TV
ventilation. Allow enough space around the
may require detaching the Table-Top Stand;
TV as shown below. Avoid operating the TV
at temperatures below 41 °F (5 °C).
see “Detaching the Table-Top Stand from
Prepare the TV for the Wall-Mount Bracket
before making cable connections.
Installed with stand
7
11
/
inches
8
For product protection and safety
reasons, Sony strongly recommends that
you use the Wall-Mount Bracket
designed for your TV and the installation
should be performed by a Sony dealer or
licensed contractor.
(30 cm)
3
2
/
inches
8
4 inches
(10 cm)
4 inches
(10 cm)
(6 cm)
Leave at least this much space around the set.
•
Follow the instruction guide provided
with the Wall-Mount Bracket for your
model. Sufficient expertise is required in
installing this TV, especially to
Installed on the wall
7
11
/
8
inches
(30 cm)
determine the strength of the wall for
withstanding the TV’s weight.
4 inches
(10 cm)
4 inches
(10 cm)
•
Be sure to use the screws supplied with
the Wall-mount bracket when attaching
the mounting hooks to the TV set.
The supplied screws are designed so that
they are 8 mm to 12 mm in length when
measured from the attaching surface of
the mounting hook.
Leave at
least this
much space
around the
set.
4 inches (10 cm)
Never install the TV set as follows:
Air circulation is blocked.
The diameter and length of the screws
differ depending on the Wall-mount
bracket model. Use of screws other than
those supplied may result in internal
damage to the TV set or cause it to fall,
etc.
Air circulation is blocked.
Wall
Wall
8-12 mm
Screw
(supplied with the
Wall-mount bracket)
Mounting Hook
~
Hook attachment on rear of
TV set
• Inadequate ventilation can lead to overheating
of the TV and may cause damage to your TV
or cause a fire.
•
Be sure to store the unused screws and
Table-Top Stand in a safe place until you
are ready to attach the Table-Top Stand.
Keep the screws away from small
children.
~
• Read the supplied Safety Booklet for
additional safety information.
16
To watch TV
To watch programs
Turn on the TV.
1
2
1-2
1 Check the ENERGY SAVING
SWITCH setting is on (z).
2 Press 1 (POWER) on the TV or
TV ?/1 on the remote control to
turn on the TV. (You may use the
TV ?/1 button located on the
back of the remote control.)
GUIDE
OPTIONS
HOME
~
• The TV image shown here may differ
from your TV but the operation of your
TV remains the same as indicated.
Select a TV channel.
0-9
ENT
2
To use the Guide
Press GUIDE to display the TV Guide
On Screen to view scheduled
programs or to select a program to
watch. Press again to exit the Guide.
Use with 0-9 and ENT to select digital
channels. For example, to enter 2.1,
press
,
,
, and ENT.
To use the TV features
Press HOME to display TV Home Menu/
XMB™ to access TV Settings and other
media and network related content.
Press OPTIONS to display a list of
convenient functions and menu shortcuts.
The Options menu items vary based on
current input and/or content.
Picture Adjustments
Sound Adjustments
Add to Favorites
Speakers
Settings
Picture
&
Display
Adjust the picture and screen settings
Press
or:
Picture Adjustments
Ambient Sensor
Screen
Pro Picture Setup
T
(Continued)
17
To use i-Manual
Your BRAVIA TV comes with an on-screen
manual. You can browse your i-Manual
anytime you need to find the varieties of
convenient functions.
Press i-MANUAL.
1
1
2
Press F/f/G/g/ to navigate
and select items.
2
i-Manual
Welcome to i-Manual
BRAVIA TV Features
Watching TV
Using the Home Menu
Fun Features with Connected Equipment
Parts Description
Troubleshooting
Index
RETURN Back
x Welcome to i-Manual
x BRAVIA TV Features
x Watching TV
x Fun Features with Connected
Equipment
Introduces how to connect and enjoy
optional equipment.
Introduces convenient features such as TV
Guide, Favorites, etc.
x Parts Description
x Troubleshooting
x Using the Home Menu
You can find solutions for your problems.
You can find how to customize your TV
settings, etc.
x Index
~
• Images and illustrations may differ from what you are watching on this TV.
18
Additional Information
Troubleshooting
The TV will indicate any problems with the STANDBY indicator flashing in red.
When the STANDBY indicator is flashing
The self-diagnosis function is activated.
1 Count how many times the STANDBY indicator flashes between each three
second break.
For example, the indicator may flash three times, go off for three seconds, then flash
again three times.
2 Press 1 (POWER) on the TV to turn it off, disconnect the AC power cord, and
inform your dealer or Sony service center of how the indicator flashes (number
of flashes).
When the STANDBY indicator is not flashing
1 Check the items in the tables below. (Also refer to “Troubleshooting” in the
i-Manual.)
2 If the problem persists, contact Sony Customer Support (information provided
on the front cover).
Condition
Explanation/Solution
Picture
There is no picture
(screen is dark) and no
sound.
• Check the antenna/cable connection.
• Connect the TV to the AC power, and press 1 (POWER) on
the TV.
• If the STANDBY indicator lights up in red, press TV ?/1
on the remote control.
Tiny black dots and/or • The screen is composed of pixels. Tiny black dots and/or
bright dots (pixels) on the screen do not indicate a
malfunction.
bright dots appear on the
screen.
General
The TV’s power cannot • Check to see the (z) mark on the ENERGY SAVING
SWITCH is pressed.
be turned on.
The TV turns off
automatically (the TV
enters standby mode).
• Check if the Sleep Timer, Timer, or Idle TV Standby is
activated.
• The Auto Shut-off function may be set to On. If Auto
Shut-off is activated and TV receives no signal, the TV will
automatically enter standby mode in 15 minutes. Check
Auto Shut-off is activated under Eco feature of this TV.
(Continued)
19
Condition
The remote does not
Explanation/Solution
• Replace the batteries.
• Your TV may be in SYNC mode. Press SYNC MENU,
select TV Control and then select Home (Menu) or
Options to control the TV.
function.
The TV and its
surrounding become
warm.
• When the TV is used for an extended period of time, the TV
and its surround may become warm to touch. This is not
malfunction of the TV.
The Parental Lock
password has been
forgotten.
• Enter 4357 for the PIN code. (PIN code 4357 is always
accepted.)
How to Care for Your BRAVIA
Safety is very important, please read and follow the safety documentation (Safety Booklet)
separately provided.
Unplug the TV and other connected equipment from the
wall outlet before you begin cleaning your TV.
• Wipe the LCD screen gently with a soft cloth.
• Stubborn stains may be removed with a cloth slightly
moistened with a solution of mild soap and warm water.
• If using a chemically pretreated cloth, please follow the
instruction provided on the package.
• Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
• Do not plug in the TV into the wall outlet until the moisture from cleaning has evaporated.
The TV should also be placed on a stable surface to prevent it from toppling over (see
page 13). If you have young children or pets at home, check regularly to insure the TV is
securely fastened.
20
Specifications
Model name KDL-
60NX801/
60NX800
52NX800
46NX800
46NX700
40NX700
System
Television system
NTSC: American TV standard
ATSC (8VSB terrestrial): ATSC compliant 8VSB
QAM on cable: ANSI/SCTE 07 2000 (Does not include CableCARD functionality)
Channel coverage
Analog terrestrial: 2 - 69 / Digital terrestrial: 2 - 69
Analog Cable: 1 - 135 / Digital Cable: 1 - 135
Panel system
LCD (Liquid Crystal Display) Panel
10 W + 10 W
Speaker output
Input/Output jacks
CABLE/ANTENNA
VIDEO IN 1/2
75-ohm external terminal for RF inputs
VIDEO / AUDIO
COMPONENT IN
YPBPR (Component Video) / Signal format: 480i, 480p, 720p, 1080i, 1080p
AUDIO
HDMI IN 1/2/3/4
HDMI: Video: 480i, 480p, 720p, 1080i, 1080p, 1080/24p
HDMI: Audio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20 and 24 bits,
Dolby Digital
AUDIO (HDMI IN 2)
AUDIO OUT
500 mVrms (typical)
DIGITAL AUDIO OUT
(OPTICAL)
PCM/Dolby Digital optical signal
PC IN
D-sub 15-pin, analog RGB
Stereo mini jack
PC/HDMI 2 AUDIO IN
LAN
10BASE-T/100BASE-TX connector (Connection speed may differ depending on the network
environment. 10BASE-T/100BASE-TX communication rate and communication quality are not
guaranteed for this TV.)*1
USB/DLNA
Refer to the i-Manual for supported format.
Power and others
Power requirement
Power consumption
in use
110-240 V AC, 50/60 Hz (U.S.A./Canada 120 V AC, 60 Hz)
222 W
169 W
153 W
129 W
109 W
in DAM*2
18 W
(You may hear a clicking noise during the download but this is normal.)
Less than 0.13 W
in standby
with 120 V AC
and less than
0.2 W with 240 V
AC
Less than 0.17 W with 120 V AC and less than 0.23 W with 240 V AC
Screen size
(inches measured diagonally)
60 inches
52 inches
46 inches
40 inches
Display resolution
1,920 dots (horizontal) × 1,080 lines (vertical)
Speaker
Full range
34 × 100 (2)
1 3/8 × 4
34 × 160 (2)
1 3/8 × 6 3/8
(mm)
(inches)
Dimensions with stand (mm)
(inches) 56
without stand (mm) 1,440 × 889 × 64 1,261 × 787 × 64 1,127 × 710 × 64 1,127 × 716 × 64 994 × 641 × 64
(inches) 56 3/4 × 35 × 2 5/8 49 3/4 × 31 × 2 5/8 44 3/8 × 28 × 2 5/8 44 3
1,440 × 927 × 380 1,261 × 819 × 400 1,127 × 742 × 320 1,127 × 748 × 320 994 × 673 × 290
3
3
/
4
× 36
/
8
× 15 49 3
/4
× 32 1
/4
× 15 3
/4
44 3
/8
× 29 1
/4
× 12 5
/8
44 3
/8
× 29 1
/2
× 12 5
/8
39 1
/4
× 26 1
/2
× 11 1
/2
/8
× 28 1
/4
× 2 5
/8
39 1
/4
× 25 1
/4
× 2 5
/8
wall-mount hole pattern(mm)
wall-mount screw size (mm)
400 × 300
300 × 300
Mass
with stand (kg)/(lb.)
50.6/111.5
43.3/95.4
36.1/79.6
30.1/66.3
28.8/63.5
24.8/54.7
27.8/61.3
24.0/52.9
22.6/49.8
19.2/42.3
without stand (kg)/(lb.)
Supplied accessories
Optional accessories
Connecting cables / Support Belt Kit / Wall-Mount Bracket / Wall-Hanging Bracket
(Continued)
21
Model name KDL-
60NX810
55NX811/
55NX810
46NX810
46NX711/
46NX710
40NX711/
40NX710
System
Television system
NTSC: American TV standard
ATSC (8VSB terrestrial): ATSC compliant 8VSB
QAM on cable: ANSI/SCTE 07 2000 (Does not include CableCARD functionality)
Channel coverage
Analog terrestrial: 2 - 69 / Digital terrestrial: 2 - 69
Analog Cable: 1 - 135 / Digital Cable: 1 - 135
Panel system
LCD (Liquid Crystal Display) Panel
8 W + 8 W + 10 W
Speaker output
Input/Output jacks
CABLE/ANTENNA
VIDEO IN 1/2
75-ohm external terminal for RF inputs
VIDEO / AUDIO
COMPONENT IN
YPBPR (Component Video) / Signal format: 480i, 480p, 720p, 1080i, 1080p
AUDIO
HDMI IN 1/2/3/4
HDMI: Video: 480i, 480p, 720p, 720/24p, 1080i, 1080p, 1080/24p
HDMI: Audio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20 and 24 bits,
Dolby Digital
AUDIO (HDMI IN 2)
AUDIO OUT
500 mVrms (typical)
DIGITAL AUDIO OUT (OPTICAL)
PCM/Dolby Digital optical signal
D-sub 15-pin, analog RGB
Stereo mini jack
PC IN
PC/HDMI 2 AUDIO IN
LAN
10BASE-T/100BASE-TX connector (Connection speed may differ depending on the
network environment. 10BASE-T/100BASE-TX communication rate and communication
quality are not guaranteed for this TV.)*1
USB/DLNA
Refer to the i-Manual for supported format.
3D Sync terminal for optional transmitter
3D SYNC
Power and others
Power requirement
Power consumption
in use
110-240 V AC, 50/60 Hz (U.S.A./Canada 120 V AC, 60 Hz)
215 W
18 W
175 W
156 W
153 W
137 W
in DAM*2
22 W
(You may hear a clicking noise during the download but this is normal.)
Less than 0.12 W with 120 V AC and less than 0.2 W with 240 V AC
54.6 inches
in standby
Screen size
(inches measured diagonally)
60 inches
46 inches
40 inches
(55 class)
Display resolution
Speaker
1,920 dots (horizontal) × 1,080 lines (vertical)
Full range
(mm)
(inches)
(mm)
20 × 70 (4)
13/16 × 2 7/8 (4)
Φ 60 (1)
20 × 90 (2)
13/16 × 3 5/8 (2)
40 × 90 (1)
Woofer
(inches)
Φ 2 3/8 (1)
1 5/8 × 3 5/8 (1)
Dimensions with stand
withoutstand
(mm)
(inches)
1,400 × 865 × 303 1,276 × 800 × 323 1,083 × 690 × 270 1,083 × 690 × 270 944 × 612 × 245
1
1
1
3
55
/8
× 34
/8
× 12 50 1
/4
× 31 1
/2
× 12 3
/4
42 3
/4
× 27 1
/4
× 10 3
/4
42 3
/4
× 27 1
/4
× 10 3
/4
37
/4
× 24 × 9
/
4
(mm)
(inches)
1,400 × 836 × 45 1,276 × 770 × 32 1,083 × 660 × 31 1,083 × 660 × 31 944 × 582 × 32
1
7
3
1
3
1
1
1
55
/
8
× 33 × 1
/8
50 1
/4
× 30 3
/
8
× 1 3
/
8
42
/
4
× 26 × 1
300 × 300
/
4
42
/
4
× 26 × 1
/4
37
/4
× 23 × 1
/
4
wall-mount hole pattern(mm)
400 × 300
wall-mount screw size (mm)
with stand (kg)/(lb.)
Mass
43.0/ 94.8
36.6/ 80.7
32.2/71
26.9/59.3
24.8/54.7
20.5/45.2
24.4/53.8
20.5/45.2
19.8/43.7
16.1/35.5
without stand (kg)/(lb.)
Supplied accessories
Optional accessories
Connecting cables / Support Belt Kit / Wall-Mount Bracket / Wall-Hanging Bracket /
3D Glasses / 3D Sync Transmitter
*1 For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied).
*2 Download Acquisition Mode (DAM) is used for software updates and/or collecting data for TV Guide On Screen.
• Optional accessories availability depends on its stock.
• Design and specifications are subject to change without notice.
22
This equipment complies with FCC/IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed and
operated with minimum distance 20 cm between the
radiator and your body (excluding extremities: hands,
wrists and feet).
This device and its antenna(s) must not be co-located or
operating with any other antenna or transmitter except
Grant condition.
Declaration of Conformity
Trade Name: SONY
Model: KDL-60NX810/KDL-60NX801/
KDL-60NX800/KDL-55NX811/KDL-55NX810/
KDL-52NX800/KDL-46NX810/KDL-46NX800/
KDL-46NX711/KDL-46NX710/KDL-46NX700/
KDL-40NX711/KDL-40NX710/KDL-40NX700
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo,
Note
San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-2230
This television includes a QAM demodulator which should
allow you to receive unscrambled digital cable television
programming via subscription service to a cable service
provider. Availability of digital cable television programming
in your area depends on the type of programming and signal
provided by your cable service provider.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Compatible optional accessories
information
Use the following Sony optional accessories with
your TV model.
For customers in Canada
This Class B digital apparatus complies with Canadian
ICES-003.
FCC Related Information
Sony Model No.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
KDL-
60NX801/ 52NX800 46NX800 40NX700
60NX800
46NX700
Sony Wall-
interference in a residential installation. This
Mount Bracket SU-WL500
SU-WL700
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1
*
Model No.
Sony Wall-
HangingBracket
SU-WH500
1
*
Model No.
Sony TV
Stand No.
SU-52NX1 SU-46NX1 SU-40NX1
Sony Model No.
2
*
KDL-
60NX810 55NX811/ 46NX810/ 40NX711/
55NX810 46NX711/ 40NX710
46NX710
❑
❑
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
❑
❑
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Sony Wall-
Mount Bracket SU-WL500
SU-WL700/WL500
1
*
Model No.
Sony Wall-
HangingBracket
SU-WH500
1
*
Pursuant to FCC regulations, you are cautioned that
any changes or modifications not expressly approved
in this manual could void your authority to operate
this equipment.
Model No.
Sony TV
Stand No.
SU-B550S SU-B460S SU-B400S
2
*
Use with other optional accessories may cause instability
and could result in property damages or injury.
Safety and Regulatory
1
To prevent radio interference to the licensed service,
this device is intended to be operated indoors and away
from windows to provide maximum shielding.
Equipment (or its transmit antenna) that is installed
outdoors is subject to licensing.
* For instructions on using with your TV please go to
download “Additional Information for Using Sony
Wall-Mount Bracket” or “Additional Information for
Using Sony Wall-Hanging Bracket”.
* Some of these TV stand models may not be available
in your area.
2
Only use Wireless LAN indoors when using it with
IEEE 802.11a/n (5 GHz).
High power radars are allocated as primary users
(meaning they have priority) of 5250-5350 MHz and
5650-5850 MHz and these radars could cause
interference and/or damage to this device.
This device uses 5 GHz band for wireless LAN
communication and the maximum gain of the antenna
in this device is 6 dBi.
To Customers
Sufficient expertise is required for TV installations. Be
sure to subcontract the installation to a Sony dealer or
licensed contractor and pay adequate attention to safety
during the installation.
23
For Your Convenience
Be sure to register your TV.
Online
Registration:
United States
Canada
Your TV is capable of receiving software updates. For the
latest information about software updates for your TV, visit:
United States
Canada
Software
Updates:
NOTE: If your TV is connected to the Internet, you can check
for software updates by selecting Settings, Product
Support and then Automatic Software Update.
© 2010 Sony Corporation Printed in U.S.A.
|