English
Electret Condenser
Microphone
Troubleshooting
Precautions
The supplied extension cord can be
used with this microphone only, and
cannot be used with any other
devices (stereo microphone, etc.).
This microphone is a precision
instrument. Never disassemble it.
Do not expose the microphone to a
mechanical shock such as by
dropping or striking it.
No sound, unable to record
The connected recorder is not a
4-273-325-11(1)
plug-in-power supply system device.
Connect the microphone to a
plug-in-power supply system
device.
Electret Condenser
Microphone
Operating Instructions
Mode d’emploi
WARNING
To reduce the risk of fire or electric
shock, do not expose this
Check with the operating
instructions of the connected
device.
apparatus to rain or moisture.
If the microphone is placed near
speakers/headphones, a high pitched
noise may be heard (howling effect).
This is caused by the microphone
catching sound from the speakers/
headphones repeatedly. In this case,
place the microphone as far as
possible from the speakers/
headphones.
Do not leave the microphone in a
humid, dusty or hot place, or under
direct sunlight. This may cause a
malfunction.
When using outdoors, never let the
microphone become wet with rain
or saltwater.
When the microphone and the plug
become dirty, wipe them with a dry
cloth. Do not blow on the
The connected recorder is a
To reduce the risk of electrical
shock, do not open the cabinet.
Refer servicing to qualified
personnel only.
monaural device.
Manual de instrucciones
Use a PC-236MS stereo-monaural
converter plug (sold separately).
©2011 Sony Corporation
Printed in China
No sound, noisy sound
The plug does not fit properly.
You are cautioned that any changes or
modifications not expressly approved
in this manual could void your
Wipe the plug with a soft cloth.
Insert the plug all the way into the
microphone jack, and make sure it
is secure.
authority to operate this equipment.
ECM-PC60
Features
High-quality metal body and a
compact, stylish, easy-to-carry
design
Specifications
Type:
Electret condenser
microphone
The supplied holding clip allows you
to use the microphone at meetings,
etc., without it getting in the way.
Acoustic characteristics suitable for
voice and chat services
Plug:
Three-conductor gold-
plated mini plug (monaural)
microphone when dusting it. A dirty
plug will cause deterioration of
sound quality and intermitted
sound.
Always hold the plug when
disconnecting. Pulling the cord may
cause it to snap.
Power supply:
Plug-in-power supply
system
Directivity:
Omni-directional
Front sensitivity (Open circuit
output voltage level):
–38.0 dB 3.5 dB
Identifying the
parts (see fig. )
(1,000 Hz, 0 dB = 1 V/Pa)
Frequency response:
50 Hz - 15,000 Hz
Microphone
Microphone holder
Post
Cord length:
Base
Approx. 1.2 m (47 1/4 in)
Dimensions (including projecting
parts):
Three-conductor gold-plated mini
plug
Sounds are output in monaural.
Cord guide
Microphone: Approx.
ø8 mm × 19 mm (11/32 in ×
3/4 in) (diameter/length)
With stand: Approx.
ø50 mm × 100 mm (2 in ×
4 in) (diameter of the base/
height)
How to use
2
With the stand
(see fig. )
Mass:
Microphone: Approx. 12 g
(0.42 oz) (Incl. cord)
With stand: Approx. 40 g
(1.4 oz)
1
Connect the plug to the
microphone jack of a plug-in-
power system recording device.
3
Operating temperature:
5 °C to 35 °C
(41 °F to 95 °F)
2
Clip the microphone in the
microphone holder, aligning
the groove () and ridge ().
Supplied accessories:
Stand (1), Extension cord
(Approx. 1.0 m (39 3/8 in)
long) (1), Holding clip (1)
3
4
Insert the cord into the cord
guide.
Adjust the post degree.
Optional accessory:
4
PC-236MS stereo-monaural
converter plug
When carrying the microphone
If the microphone is
connected to a monaural
recorder, the microphone
may not be able to work to
its full capability, depending
on the recorder. In such a
case, use the PC-236MS
stereo-monaural converter
plug.
(see fig. )
Remove the microphone from the
microphone holder, and fold the post
against the base.
MIC
(PLUG IN POWER)
With the holding clip
1
(see fig. )
Clip the microphone in the
microphone holder of the clip, aligning
the groove () and ridge ().
Design and specifications are subject
to change without notice.
|