OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW TREADMILL!
CONGRATULATIONS ON YOUR
NEW TREADMILL AND WELCOME
TO THE SPIRIT FAMILY!
Thank you for your purchase of this quality treadmill from Spirit Manufacturing, Inc.
Your new treadmill was manufactured by one of the leading fitness manufacturers in
the world and is backed by one of the most comprehensive warranties available.
Through your dealer, Spirit will do all we can to make your ownership experience as
pleasant as possible for many years to come. The local dealership where you
purchased this treadmill is your administrator for all Spirit warranty and service needs.
Their responsibility is to provide you with the technical knowledge and service
personnel to make your experience more informed and any difficulties easier to
remedy.
Please take a moment at this time to record the name of the dealer, their telephone
number, and the date of purchase below to make any future, needed contact easy. We
appreciate your support and we will always remember that you are the reason that we
are in business. Please complete and mail your registration card today and enjoy your
new treadmill.
Yours in Health,
Spirit Manufacturing, Inc.
Name of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase Date_______________________________________
Product Registration
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the space provided below.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
Ver. A
XT9
2
Important Safety Instructions
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your Spirit treadmill from the
electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install
the treadmill on a flat level surface with access to a 120-volt, 20-amp grounded outlet.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED
PLUG BY USING IMPROPER ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A
serious shock or fire hazard may result along with computer malfunctions. See
Grounding Instructions, page 3.
Ŷ
Ŷ
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both
carpet and treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance
between the rear of the treadmill and any fixed object.
ŶKeep children away from the treadmill. There are obvious pinch points and other
caution areas that can cause harm.
Ŷ
Ŷ
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not working
properly, call your dealer.
ŶKeep the cord away from heated surfaces.
Ŷ
Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
Ŷ
Ŷ
Ŷ
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, remove tether cord, then remove the plug
from the outlet.
Ŷ
Ŷ
Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
The pulse sensors are not medical devices. Various factors, including the user¶s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
Ŷ
Ŷ
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Remove tether cord after use to prevent unauthorized treadmill operation.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
XT9
3
Important Electrical Information
WARNING!
ƔNEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill.
Route the power cord away from any moving part of the treadmill including the elevation
mechanism and transport wheels.
Ɣ
NEVER remove any cover without first disconnecting AC power.
ƔIf voltage varies by ten percent (10%) or more, the performance of your treadmill may
be affected. Such conditions are not covered under your warranty. If you suspect
the voltage is low, contact your local power company or a licensed electrician for proper
testing. See Diagnosis Guide, page 27.
ƔNEVER expose this treadmill to rain or moisture. This product is NOT designed for
use outdoors, near a pool or spa, or in any other high humidity environment.
Grounding Instructions
This product must be grounded. If the treadmill should malfunction or breakdown, grounding
provides a path of least resistance for electric current, reducing the risk of electric shock. This
product is equipped with a cord having an equipment-grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with
all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in
doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product if it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below
may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded
outlet is not available. The temporary adapter should be used only until a properly grounded
outlet (below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the
like, extending from the adapter, must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal
screw.
Adapter
Grounded Outlet
Tab of
Grounding
Metal Screw
Screw
Grounding Pin
Grounded Outlet Box
XT9
4
ƔNEVER operate this treadmill without reading and completely understanding the results of
any operational change you request from the computer.
Ɣ
Understand that changes in speed and incline do not occur immediately. Set your desired
speed on the computer console and release the adjustment key. The computer will obey the
command gradually.
ƔNEVER use your treadmill during an electrical storm. Surges may occur in your household
power supply that could damage treadmill components.
ƔUse caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance or stray
from walking in the center of the belt; which may result in serious injury.
ƔNEVER mount or dismount the treadmill while the belt is moving. Spirit treadmills start with
at a very low speed and it is unnecessary to straddle the belt during start up. Simply
standing on the belt during slow acceleration is proper after you have learned to operate the
unit.
ƔAlways hold on to a handrail or hand bar while making control changes (incline, speed, etc.).
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure. Pushing harder is not going to make the unit go
faster or slower. If you feel the buttons are not functioning properly with normal pressure
contact your Spirit dealer.
Safety Tether Cord
A safety tether cord is provided with this unit. It is a simple magnetic design that should be
used at all times. It is for your safety should you fall or move too far back on the tread-belt.
Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the round metal portion of the console control head. Your
treadmill will not start and operate without this. Removing the magnet also secures the
treadmill from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note: The
magnet has strong enough power to minimize accidental, unexpected stopping. The clip
should be attached securely to make certain it does not come off. Be familiar with its function
and limitations. The treadmill will stop, depending on speed, with a one to two step coast
anytime the magnet is pulled off the console. Use the red Stop / Pause switch in normal
operation.
XT9
5
Assembly Instructions
ASSEMBLY PACK CHECK LIST
(4 pcs) 5/16´ x 19 x 1.5T Curved Washer
(4 pcs) M5 x 15 m/m Phillips Head Screw
(14 pcs) 5/16´ x15m/m Button Head Socket Screw
(1pc) Safety Key
(1 pc) Deck / Belt Lubricant
(1 pc) Combination M5 Allen Wrench & Phillips Head Screwdriver
(1pc) M6 Allen Wrench
Assembly
Ŷ
Ŷ
Ŷ
STEP 1
Remove all parts from the carton.
STEP 2
Connect Lower computer cable with Middle computer cable.
STEP 3
Hand tighten Right and Left uprights into the upright receiving tube of frame base with 8
pcs of 5/16´x 15m/m Button Head Socket Screws and 2pcs of 5/16´ x 19 x 1.5T Curved
Washers by using the Combination M5 allen Wrench & Phillips head screwdriver.
Ŷ
Ŷ
STEP 4
Connect Middle computer cable with Upper computer cable.
STEP 5
Install the Console Support into the Right and Left uprights with 6 pcs of 5/16´ x 15m/m
Button Head Socket Screws and 2pcs of 5/16´ x 19 x 1.5T Curved Washers by using the
Combination M5 allen wrench &
.
Phillips head screwdriver
Install Upper computer cable into the Console.
Install Speed cable and Incline cable into the Console.
Install 2pcs of Handpulse cable into the Console.
Ŷ
Ŷ
STEP 6
Slide the Console onto Console Support plate and attach with 4 pcs of M5 x 15 m/m
Phillips head screws by using the Combination M5 Allen Wrench & Phillips head
screwdriver.
Note that the console support plate should be inside the console housing and that the
mounting screws install though the console housing and into the mounting plate.
PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN
ASSEMBLED.
XT9
6
Assembly Instructions
XT9
7
Folding Instructions
Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power
cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired
position.
Ŷ
To Fold The Treadmill:
Make certain the treadmill is at minimum incline. Lift the treadmill running deck until it
is secured by the locking telescoping tube assembly in center back of base.
ŶTo Unfold The Treadmill:
Apply slight forward pressure* on the treadmill running deck with one hand. Pull down on the
unlocking lever and slowly lower the running deck to the floor. The deck will lower unassisted
when it reaches about waist high.
*At the rear roller area to relieve pressure on the locking system.
Transport
The treadmill is equipped with four transport wheels which are engaged when the treadmill is
folded. After folding simply roll the treadmill away.
XT9
8
Operation of Your Treadmill
Getting familiar with the control panel
Ŷ
XT9 Console
Getting started:
Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the power
switch located at the front of the treadmill below the motor hood. Ensure that the safety key is
installed, as the treadmill will not operate without it.
When the power is turned on, a message will scroll across the dot matrix showing the current
software version. Then the Time and Distance windows will display Odometer readings for a
short time, Time window will show how many hours the treadmill has been in use and the
Distance window will show how many miles (or Kilometers if the treadmill is set to metric
readings) the treadmill has gone. The treadmill will then enter idle mode, which is the starting
point for operation.
XT9
9
Quick-Start Operation:
STEP 1: Attach the Safety key to enable the display (if not already on).
STEP 2: Press the Start key to begin belt movement, then adjust to the desired speed using
the Fast / Slow keys (console or handgrip). You may also use the rapid speed keys 2 through
10 to adjust the speed.
STEP 3: To slow tread-belt press and hold the Slow key (console or handgrip) to the desired
speed. You may also press the rapid speed adjust keys, 2 through 10.
STEP 4: To stop the tread-belt press Stop key or pull away Safety key.
Pause/Stop/Reset Feature:
STEP 1: When the treadmill is running the pause feature may be utilized by pressing the red
Stop key once. This will slowly decelerate the tread-belt to a stop. The incline will go to zero
percent. The Time, Distance and Calorie readings will hold while the unit is in the pause mode.
After 5 minutes the display will reset and return to the start up screen.
STEP 2: To resume your exercise, when in Pause mode, press the Start key. The speed and
incline will return to their previous settings.
l
Pause is executed when the Stop button is pressed once. If the Stop key is pressed a
second time, the program will end and a workout summary will be displayed. If the Stop
button is pressed a third time, the console will return to the idle mode (start up) screen. If
the Stop button is held down for more than 3 seconds the console will reset.
Incline Feature:
l
Incline may be adjusted anytime after belt movement.
l
Press and hold the Adjust UP/DOWN keys (console or handgrip) to achieve desired level
of effort. You may also choose a more rapid increase / decrease by selecting desired key, 2
through 10, on left hand side of console (incline).
l
The display will indicate incline position as adjustments are made.
XT9
10
Dot Matrix Center Display (Program Operation):
Twenty rows of dots (8 high) indicate each segment of a workout. The dots are only to show an
approximate level (speed/incline) of effort. They do not necessarily indicate a specific value -
only an approximate percent to compare levels of intensity. In operation the Speed / Incline dot
matrix window will build a profile ³picture´ as values are changed during a workout.
When the Speed indicator which is above dot matrix is lit the Dot matrix displays the Speed
profile and when the Incline indicator is lit the Dot Matrix displays the Incline profile.
You may change the Dot Matrix profile view which you desired by pressing the DISPLAY button.
After scrolling through the three profiles which include incline, speed and incline+ speed profile,
by pressing the DISPLAY button, the Dot matrix will automatically scroll through the three
displays showing each one for five seconds.
1/4 mile Track:
The 1/4 mile track will be displayed around the dot matrix window. The flashing dot indicates
your progress. Once the 1/4 mile is complete this feature will begin again. The amount of laps
are accumuled in the laps window which is below PULSE.
Pulse Grip Feature:
The Pulse (Heart Rate) console window will display your current heart rate in beats per minute
during the workout. You must use both stainless steel sensors on the front cross bar to display
your pulse or the wireless chest strap. Pulse value displays anytime the upper display is
receiving a Pulse signal.
Calorie Display:
Displays the cumulative calories burned at any given time during your workout.
Note: This is only a rough guide used for comparison of different exercise sessions, which
cannot be used for medical purposes.
To Turn Treadmill Off (Blank out Display):
Two methods accomplish this: Use either one.
(1) Display will automatically turn off (blank out) after 10 minutes (no key operations) in
Pause / Stop mode.
(2) Remove safety key.
XT9
11
Programmable Features
Factory preset programs (P1~P5), 2 user defined programs, and one Manual program.
Each preset program has a maximum speed level that is displayed when a desired workout is
chosen. The maximum speed that the particular program will achieve will be displayed in the
Speed window.
Also included are two user programs (User 1 and User 2) for custom workouts.
To Select a Program:
STEP 1: Press the PROGRAM
Ÿź
key to select desired program. Press enter to select the
program. The display will prompt you through the programming or you can just press Start to
begin the program with default values.
STEP 2: If enter was pressed, the Time window will display with the default value of 20 minutes.
You may use any of the up/down, fast/slow keys to adjust the time. After adjusting, or to accept
the default value, press enter. (Note: You may press start at any time during the programming to
start the program.)
STEP 3: The Calorie window will now be displaying a value, which is your Body Weight.
Entering the correct body weight will affect the calorie count. Use the Up/Down keys, Fast/Slow
to adjust, then press enter.
A note about the Calorie display: No exercise machine can give you an exact calorie count
because there are too many factors which determine exact calorie burn for a particular person.
Even if someone is the exact same body weight, age and height, their calorie burn may be very
different than yours. The Calorie display is to be used as a reference only to monitor
improvement from workout to workout.
STEP 4: The Calorie window will display the preset top speed of the selected program. Use the
Up/Down, Fast/Slow keys to adjust, then press enter. Each program has various speed changes
through out, this allows you to limit the highest speed the program can reach.
User Programs:
STEP 1: Select User 1 or User 2 via the PROGRAM key then press Enter. Note that the dot
matrix display portion will have a single row of dots at the bottom (Unless there is a previously
stored program).
STEP 2: Note the Time window is flashing. Use the Adjust UP/DOWN keys to adjust up from 10
minutes (if desired). Press ENTER key. This is a must to continue even if time is not adjusted.
STEP 3: The Calorie window will now be blinking a bodyweight value. Enter your bodyweight
and press Enter.
STEP 4: The Calorie window will now be blinking an Age value. Adjust the age and press enter.
XT9
12
STEP 5: The first column (segment) will now be blinking. Using the Fast / Slow or rapid keys,
adjust the speed level to your desired effort for the first segment then press enter. The second
column will now be blinking. Repeat the above process until all segments have been
programmed. The first column will be blinking again. This is for the incline programming. Repeat
the above process to program all segments for incline.
STEP 6: Press the Start button to begin the workout and also save the program to memory.
XT9
13
General Maintenance
Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is
maximized when the bed is kept as clean as possible. Use a soft, damp cloth or paper towel to
wipe the edge of the belt and the area between the belt edge and frame. Also reach as far as
practical directly under the belt edge. This should be done once a month to extend belt and
bed life. Use water only - no cleaners or abrasives. A mild soap and water solution along with
a nylon scrub brush will clean the top of the textured belt. Allow to dry before using.
Belt Dust - This occurs during normal break-in or until the belt stabilizes. Wiping excess off
with a damp cloth will minimize buildup.
General Cleaning - Dirt, dust, and pet hair can block air inlets and accumulate on the running
belt. On a monthly basis, vacuum underneath your treadmill to prevent buildup. Once a year,
you should remove the black motor hood and vacuum out dirt that may accumulate. UNPLUG
POWER CORD BEFORE THIS TASK.
BELT ADJUSTMENTS:
Treadbelt Tension Adjustment - Belt tension is not critical for most users. It is very important
for joggers and runners in order to provide a smooth, steady running surface. Adjustment must
be made from the right side of the rear roller in order to adjust tension with the 6 mm Allen
wrench provided in the parts package. The adjustment bolt is located at the end of the right
side rail as noted in diagram below.
Tracking / Tension
Adjustment
Tracking / Tension
Adjustment
Note: Adjustment is through small hole in end
Tighten the rear roller only enough to prevent slippage at the front roller. Turn the treadbelt
tension adjusting bolt in increments of 1/4 turn and inspect for proper tension.
When an adjustment is made to the belt tension, you must also make a tracking
adjustment to compensate for the change in belt tension. This is accomplished by turning
both the tension and tracking Allen bolts an equal amount. This adjustment should be made by
turning both bolts clockwise by no more than a 1/4 turn at a time.
DO NOT OVERTIGHTEN ± Over tightening will cause belt damage and premature bearing
failure.
XT9
14
TREADBELT TRACKING ADJUSTMENT:
The performance of your treadmill is dependent on the frame running on a reasonably level
surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt
adjustment may be necessary.
The treadmill is designed to keep the treadbelt reasonably centered while in use. It is normal
for some belts to drift near one side while the belt is running with no one on it. After a few
minutes of use, the treadbelt should have a tendency to center itself. If, during use, the belt
continues to move toward one side, adjustments are necessary.
TO SET TREADBELT TRACKING:
A 6 mm Allen wrench is provided to adjust the rear roller. Make tracking adjustments from the
left side only. Set belt speed at
approximately 2 to 3 mph. A small
adjustment can make a dramatic difference.
Turn the bolt only a 1/4 turn and wait a few
minutes for the belt to adjust itself.
Continue to make 1/4 turns until the belt
stabilizes in the center of the running deck.
The belt may require periodic tracking
adjustment depending on use and
walking/running characteristics. Some
users will affect tracking differently. Expect
to make adjustments as required to center the treadbelt. Adjustments will become less of a
maintenance concern as the belt is used. Proper belt tracking is an owner responsibility
common with all treadmills.
ATTENTION:
DAMAGE TO THE RUNNING BELT RESULTING FROM IMPROPER TRACKING /
TENSION ADJUSTMENTS IS NOT COVERED UNDER THE SPIRIT WARRANTY.
XT9
15
BELT / DECK LUBRICATION:
Do not lubricate with other than Spirit approved lubricant. Your treadmill comes with one tube of
lubricant and extra tubes can be ordered directly from Spirit. There are commercially available
lube kits, but the only one currently approved by Spirit is Lube-N-Walk. These kits come with an
application wand that makes applying the lubrication easier. The kits can be purchased from Spirit
or directly from Lube-N-Walk here: http://www.jadfitness.com/
Keeping the deck lubricated at the recommended intervals ensures the longest life possible for
your treadmill. If the lubricant dries out, the friction between the belt and deck rises and places
undue stress on the drive motor, drive belt and electronic motor control board, which could result
in catastrophic failure of these expensive components. Failure to lubricate the deck at regular
intervals may void the warranty.
The deck comes pre-lubricated and subsequent lubrication should be performed every 180 hours
of use, or every three months, whichever comes first. The console has a built in lubrication
reminder indicator that lights every 180 hours of use. To lubricate the deck with the tube of
lubricant supplied it will be necessary to loosen the walking belt. Using the 6 mm allen wrench
supplied, loosen the two rear roller adjustment bolts -- located in the rear end caps ± enough to
get your hand under the belt (5 ±10 turns). Make sure to loosen both bolts the same amount of
turns and also remember how many turns, because when finished you will need to tighten the
bolts back to the point they were before.
Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the
whole tube of lubricant onto the deck surface about 18 inches from the motor cover. Squeeze out
the contents of the tube across the deck (parallel to the motor cover) in about a one foot line, like
toothpaste on a toothbrush. The one foot line should be in the middle of the deck at approximately
equal distance from both side edges of the belt. You want the lubricant to be applied about the
spot that your feet would hit the belt as you are walking. This should be about 18 inches from the
motor cover, but you may want to walk on the treadmill before loosening the belt to note where
your feet land on the belt. If you mostly run on the treadmill the spot where your feet land may be
different from walking.
Once the lubricant is applied, tighten the rear roller bolts the same amount of turns as when you
loosened them. Run the treadmill at about 6 mph without walking on it for about a minute or two
to make sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the
belt tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on
the treadmill immediately for at least 5 minutes to ensure the lubricant is evenly distributed. If you
purchase a Lube-N-Walk kit, follow the instructions that come with it to apply the lubrication.
XT9
16
Service Checklist - Diagnosis Guide
Before contacting your dealer for aid, please review the following information. It may save you
both time and expense. This list includes common problems that may not be covered under
the treadmill¶s warranty.
PROBLEM
SOLUTION/CAUSE
Display does not light
Tether cord not in position.
Circuit breaker on front grill tripped. Push circuit breaker in
until it locks.
Plug is disconnected. Make sure plug is firmly pushed into
AC household wall outlet.
Household circuit breaker may be tripped.
Treadmill defect. Contact your Spirit dealer.
Treadbelt does not stay centered
Treadmill belt hesitates when walked/run on
A user may be walking while favoring or putting more weight
on either the left or right foot. If this walking pattern is natural,
track the belt slightly off-center to the side opposite from the
belt movement. See General Maintenance section on
Treadbelt Tension. Adjust as necessary.
Motor is not responsive / Display is lit
Make certain clock is running.
Treadmill will only achieve approximately
7 mph but shows higher speed on display
This indicates motor should be receiving power to
operate. Low AC voltage to treadmill. Do not use an
extension cord. If an extension cord is required it should be
as short as possible and heavy duty 16 gauge minimum. Low
household voltage. Contact an electrician or your Spirit dealer.
A minimum of 110 volt AC current is required.
Treadbelt stops quickly/suddenly when
tether cord is pulled
High belt/deck friction. See General Maintenance
section on lubrication.
Treadmill trips on board 15 amp circuit
Computer shuts off when console is
High belt/deck friction. See General Maintenance
touched (on a cold day)while walking/running Treadmill is not grounded. Static electricity is ³crashing´ the
computer. Refer to Grounding Instructions on page 4.
XT9
17
Manufacturer’s Limited Warranty
Effective October 15, 2006
TREADMILL WARRANTY
Spirit Manufacturing Inc. warrants all its home use treadmills¶ parts for a period of 5 years from the date of retail sale, as determined by sale receipt,
or in the absence of a receipt eighteen (18) months from the original factory shipping date. Spirit¶s responsibilities include providing new or
remanufactured parts, at Spirit¶s option, and technical support to our independent dealers and servicing organizations. In the absence of a dealer
or service organization, these warranties will be administered by Spirit directly to a consumer. An extended warranty period applies to the following
components:
Home Use WARRANTY
Drive Motor
30 Years
3 Years
Lifetime
1 Year
Electronics / Belt / Rollers
Frame Weldments
Labor
NORMAL RESPONSIBILITIES OF THE CONSUMER
This warranty applies only to products in ordinary household use or light Institutional facility. The consumer is responsible for the items listed
below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original purchase to
validate the manufacturer¶s limited warranty.
2. Proper use of the treadmill in accordance with the instructions provided in this manual, including belt tracking.
3. Proper installation by an authorized Spirit service company in accordance with instructions provided with the treadmill and with all local electric
codes.
4. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house
wiring.
5. Expenses for making the treadmill accessible for servicing, including any item that was not part of the treadmill at the time it was shipped from
the factory.
6. Damages to the treadmill finish during shipping, installation or following installation.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve malfunction or
defects in workmanship or material, for units that are beyond the warranty period, for units that are beyond the service call
reimbursement period, for treadmills not requiring component replacement, or treadmills not in ordinary household use.
3. Damages caused by services performed by persons other than authorized Spirit service companies; use of parts other than original
Spirit parts; or external causes such as alterations, modifications, abuse, misuse, accident, improper maintenance, inadequate power supply, or
acts of God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been sold, transferred, bartered, or given to a third party.
6. Products that do not have a warranty registration card on file at Spirit Mfg. Spirit reserves the right to request proof of
purchase if no warranty record exists for the product.
7. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
SERVICE
Keep your bill of sale. Twelve (12) months from the date on the bill of sale or eighteen (18) months from the date of factory
shipping as determined by the serial number establishes the warranty period should service be required. If service is performed,
it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have
other rights that vary from state to state. Service under this warranty must be obtained by following these steps, in order:
1. Contact your selling authorized Spirit dealer. OR
2. Contact your local authorized Spirit service organization.
3. If there is a question as to where to obtain service, contact our service department at (870) 935-1107.
4. If no local service is available, Spirit will repair or replace the parts, at Spirit¶s option, within the warranty period at no charge
for parts. All transportation costs, both to our factory and upon return to the owner, are the responsibility of the owner. The
owner is responsible for adequate packaging upon return to Spirit. Spirit is not responsible for damages in shipping. Make all
freight damage claims with the appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN
AUTHORIZATION NUMBER. All units arriving without a return authorization number will be refused.
5. For any further information, or to contact our service department by mail, send your correspondence to:
Spirit Manufacturing, Inc.
P.O. Box 2037
Jonesboro, AR 72402-2037
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by
Spirit Manufacturing, Inc. This warranty applies only in the 50 states of the U.S.A. and Canada.
XT9
18
|